at91sam9260/9g20-ek: add usb host, device and mci support

configure BP4 and BP3

use BP4 to start DFU mode at boot

if BP4 is pressed at boot time and maintain at least 5s the dfu is started
otherwise we boot normaly

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

1 files changed, 46 insertions, 0 deletions

diff --git a/arch/arm/boards/at91sam9260ek/init.c b/arch/arm/boards/at91sam9260ek/init.c
index 5aacc75123..dbd65418ec 100644
--- a/arch/arm/boards/at91sam9260ek/init.c
+++ b/arch/arm/boards/at91sam9260ek/init.c
@@ -165,6 +165,40 @@ static void at91sam9260ek_phy_reset(void)
 				     AT91_RSTC_URSTEN);
 }
 
+/*
+ * MCI (SD/MMC)
+ */
+#if defined(CONFIG_MCI_ATMEL)
+static struct atmel_mci_platform_data __initdata ek_mci_data = {
+	.bus_width	= 4,
+};
+
+static void ek_usb_add_device_mci(void)
+{
+	if (machine_is_at91sam9g20ek())
+		ek_mci_data.detect_pin = AT91_PIN_PC9;
+
+	at91_add_device_mci(1, &ek_mci_data);
+}
+#else
+static void ek_usb_add_device_mci(void) {}
+#endif
+
+/*
+ * USB Host port
+ */
+static struct at91_usbh_data __initdata ek_usbh_data = {
+	.ports		= 2,
+};
+
+/*
+ * USB Device port
+ */
+static struct at91_udc_data __initdata ek_udc_data = {
+	.vbus_pin	= AT91_PIN_PC5,
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
+};
+
 static int at91sam9260ek_mem_init(void)
 {
 	at91_add_device_sdram(64 * 1024 * 1024);
@@ -173,11 +207,23 @@ static int at91sam9260ek_mem_init(void)
 }
 mem_initcall(at91sam9260ek_mem_init);
 
+static void __init ek_add_device_buttons(void)
+{
+	at91_set_gpio_input(AT91_PIN_PA30, 1);	/* btn3 */
+	at91_set_deglitch(AT91_PIN_PA30, 1);
+	at91_set_gpio_input(AT91_PIN_PA31, 1);	/* btn4 */
+	at91_set_deglitch(AT91_PIN_PA31, 1);
+}
+
 static int at91sam9260ek_devices_init(void)
 {
 	ek_add_device_nand();
 	at91sam9260ek_phy_reset();
 	at91_add_device_eth(&macb_pdata);
+	at91_add_device_usbh_ohci(&ek_usbh_data);
+	at91_add_device_udc(&ek_udc_data);
+	ek_usb_add_device_mci();
+	ek_add_device_buttons();
 
 	armlinux_set_bootparams((void *)(AT91_CHIPSELECT_1 + 0x100));
 	ek_set_board_type();