diff options
author | Andrey Smirnov <andrew.smirnov@gmail.com> | 2017-02-03 07:53:23 -0800 |
---|---|---|
committer | Sascha Hauer <s.hauer@pengutronix.de> | 2017-02-07 09:46:38 +0100 |
commit | aefc67826ed9e8eea82851dec4de10b94015b062 (patch) | |
tree | 4f2871567e89b313406a03fbbaa1b41a76575a9f /arch/arm/dts | |
parent | 1dfe9f050f54c7e9d6cfe971aff354ff531e5d91 (diff) | |
download | barebox-aefc67826ed9e8eea82851dec4de10b94015b062.tar.gz barebox-aefc67826ed9e8eea82851dec4de10b94015b062.tar.xz |
i.MX: vf610: Add support for ZII VF610 Dev Family
Add support for ZII VF610 Dev based designs such as:
- VF610 Dev, revision B
- VF610 Dev, revision C
- CFU1, revision A
- SPU3, revision A
- SCU4 AIB, revision C
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Diffstat (limited to 'arch/arm/dts')
-rw-r--r-- | arch/arm/dts/Makefile | 7 | ||||
-rw-r--r-- | arch/arm/dts/vf610-zii-cfu1-rev-a.dts | 208 | ||||
-rw-r--r-- | arch/arm/dts/vf610-zii-dev-rev-b.dts | 431 | ||||
-rw-r--r-- | arch/arm/dts/vf610-zii-dev-rev-c.dts | 445 | ||||
-rw-r--r-- | arch/arm/dts/vf610-zii-dev.dtsi | 436 | ||||
-rw-r--r-- | arch/arm/dts/vf610-zii-scu4-aib-rev-c.dts | 457 | ||||
-rw-r--r-- | arch/arm/dts/vf610-zii-spu3-rev-a.dts | 140 |
7 files changed, 2124 insertions, 0 deletions
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index d77a7b612c..70359d8242 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -82,5 +82,12 @@ pbl-dtb-$(CONFIG_MACH_VSCOM_BALTOS) += am335x-baltos-minimal.dtb.o pbl-dtb-$(CONFIG_MACH_WARP7) += imx7s-warp.dtb.o pbl-dtb-$(CONFIG_MACH_VF610_TWR) += vf610-twr.dtb.o pbl-dtb-$(CONFIG_MACH_ZII_RDU2) += imx6q-zii-rdu2.dtb.o imx6qp-zii-rdu2.dtb.o +pbl-dtb-$(CONFIG_MACH_ZII_VF610_DEV) += \ + vf610-zii-dev-rev-b.dtb.o \ + vf610-zii-dev-rev-c.dtb.o \ + vf610-zii-cfu1-rev-a.dtb.o \ + vf610-zii-spu3-rev-a.dtb.o \ + vf610-zii-scu4-aib-rev-c.dtb.o + clean-files := *.dtb *.dtb.S .*.dtc .*.pre .*.dts *.dtb.lzo diff --git a/arch/arm/dts/vf610-zii-cfu1-rev-a.dts b/arch/arm/dts/vf610-zii-cfu1-rev-a.dts new file mode 100644 index 0000000000..4147d138bc --- /dev/null +++ b/arch/arm/dts/vf610-zii-cfu1-rev-a.dts @@ -0,0 +1,208 @@ +/* + * Copyright (C) 2015, 2016 Zodiac Inflight Innovations + * + * Based on an original 'vf610-twr.dts' which is Copyright 2015, + * Freescale Semiconductor, Inc. + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + + + +/dts-v1/; +#include "vf610-zii-dev.dtsi" + +/ { + model = "ZII VF610 CFU1 Switch Management Board"; + compatible = "zii,vf610cfu1-a", "zii,vf610dev", "fsl,vf610"; + + aliases { + /delete-property/ serial1; + /delete-property/ serial2; + }; + + gpio-leds { + debug { + gpios = <&gpio2 18 GPIO_ACTIVE_HIGH>; + }; + + fail { + label = "zii_fail"; + gpios = <&gpio3 12 GPIO_ACTIVE_LOW>; + default-state = "off"; + max-brightness = <1>; + }; + + status { + label = "zii_status"; + gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>; + default-state = "off"; + max-brightness = <1>; + }; + + status_a { + label = "zii_status_a"; + gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>; + default-state = "off"; + max-brightness = <1>; + }; + + status_b { + label = "zii_status_b"; + gpios = <&gpio3 15 GPIO_ACTIVE_HIGH>; + default-state = "on"; + max-brightness = <1>; + }; + }; +}; + +&dspi1 { + bus-num = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_dspi1>; + status = "okay"; + + m25p128@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "m25p128", "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <50000000>; + + partition@0 { + label = "m25p128-0"; + reg = <0x0 0x01000000>; + }; + }; +}; + +&esdhc0 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_esdhc0>; + bus-width = <8>; + status = "okay"; +}; + +&fec0 { + status = "disabled"; +}; + +&i2c0 { + clock-frequency = <400000>; + + pca9554@22 { + compatible = "nxp,pca9554"; + reg = <0x22>; + gpio-controller; + #gpio-cells = <2>; + }; +}; + +/delete-node/ &i2c1; +/delete-node/ &i2c2; +/delete-node/ &uart1; +/delete-node/ &uart2; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hog>; + + pinctrl_hog: hoggrp { + fsl,pins = < + VF610_PAD_PTE2__GPIO_107 0x31c2 /* SOC_SW_RSTn */ + VF610_PAD_PTB28__GPIO_98 0x31c1 /* E6352_INTn */ + + /* PTE27 is wired to signal SD on part CONN + * SFF-F4 via net FIM_DS. An active high + * on this indicates a received optical + * signal + + * SPEED=0b11 HIGH, SRE=0b0, ODE=0b0, HYS=0b0 + * DSE=0b001 150Ohm, PUS=0b10 100k UP + * PKE=0b0, PUE=0b0, OBE=0b0, IBE=0b1 + */ + VF610_PAD_PTE27__GPIO_132 0x3061 + + /* + * PTE13 is wired to signal T_DIS on part CONN + * SFF-F4 via net FIM_TDIS. Setting this high + * will disable optical output from the SFF-F4 + + * SPEED=0b11 HIGH, SRE=0b0, ODE=0b0, HYS=0b0 + * DSE=0b001 150Ohm, PUS=0b00 100k DOWN + * PKE=0b0, PUE=0b0, OBE=0b1, IBE=0b1 + * TODO: probably want IBE=0b0 + */ + VF610_PAD_PTE13__GPIO_118 0x3043 + >; + }; + + pinctrl_dspi1: dspi1grp { + fsl,pins = < + VF610_PAD_PTD5__DSPI1_CS0 0x1182 + VF610_PAD_PTC6__DSPI1_SIN 0x1181 + VF610_PAD_PTC7__DSPI1_SOUT 0x1182 + VF610_PAD_PTC8__DSPI1_SCK 0x1182 + >; + }; + + pinctrl_esdhc0: esdhc0grp { + fsl,pins = < + VF610_PAD_PTC0__ESDHC0_CLK 0x31ef + VF610_PAD_PTC1__ESDHC0_CMD 0x31ef + VF610_PAD_PTC2__ESDHC0_DAT0 0x31ef + VF610_PAD_PTC3__ESDHC0_DAT1 0x31ef + VF610_PAD_PTC4__ESDHC0_DAT2 0x31ef + VF610_PAD_PTC5__ESDHC0_DAT3 0x31ef + VF610_PAD_PTD23__ESDHC0_DAT4 0x31ef + VF610_PAD_PTD22__ESDHC0_DAT5 0x31ef + VF610_PAD_PTD21__ESDHC0_DAT6 0x31ef + VF610_PAD_PTD20__ESDHC0_DAT7 0x31ef + >; + }; + + pinctrl_leds_debug: pinctrl-leds-debug { + fsl,pins = < + VF610_PAD_PTD3__GPIO_82 0x31c2 + VF610_PAD_PTE3__GPIO_108 0x31c2 + VF610_PAD_PTE4__GPIO_109 0x31c2 + VF610_PAD_PTE5__GPIO_110 0x31c2 + VF610_PAD_PTE6__GPIO_111 0x31c2 + >; + }; +}; diff --git a/arch/arm/dts/vf610-zii-dev-rev-b.dts b/arch/arm/dts/vf610-zii-dev-rev-b.dts new file mode 100644 index 0000000000..bf0a01021e --- /dev/null +++ b/arch/arm/dts/vf610-zii-dev-rev-b.dts @@ -0,0 +1,431 @@ +/* + * Copyright (C) 2015, 2016 Zodiac Inflight Innovations + * + * Based on an original 'vf610-twr.dts' which is Copyright 2015, + * Freescale Semiconductor, Inc. + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; + +#include "vf610-zii-dev.dtsi" + +/* + * ============================================================= + * The following code is shared with Linux kernel and should be + * removed once it trickles down from there eventually + * ============================================================= + */ + +/ { + model = "ZII VF610 Development Board, Rev B"; + compatible = "zii,vf610dev-b", "zii,vf610dev", "fsl,vf610"; + + mdio-mux { + compatible = "mdio-mux-gpio"; + pinctrl-0 = <&pinctrl_mdio_mux>; + pinctrl-names = "default"; + gpios = <&gpio0 8 GPIO_ACTIVE_HIGH + &gpio0 9 GPIO_ACTIVE_HIGH + &gpio0 24 GPIO_ACTIVE_HIGH + &gpio0 25 GPIO_ACTIVE_HIGH>; + mdio-parent-bus = <&mdio1>; + #address-cells = <1>; + #size-cells = <0>; + + mdio_mux_1: mdio@1 { + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + + switch0: switch0@0 { + compatible = "marvell,mv88e6085"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + dsa,member = <0 0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + label = "lan0"; + }; + + port@1 { + reg = <1>; + label = "lan1"; + }; + + port@2 { + reg = <2>; + label = "lan2"; + }; + + switch0port5: port@5 { + reg = <5>; + label = "dsa"; + phy-mode = "rgmii-txid"; + link = <&switch1port6 + &switch2port9>; + }; + + port@6 { + reg = <6>; + label = "cpu"; + ethernet = <&fec1>; + fixed-link { + speed = <100>; + full-duplex; + }; + }; + }; + }; + }; + + mdio_mux_2: mdio@2 { + reg = <2>; + #address-cells = <1>; + #size-cells = <0>; + + switch1: switch1@0 { + compatible = "marvell,mv88e6085"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + dsa,member = <0 1>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + label = "lan3"; + phy-handle = <&switch1phy0>; + }; + + port@1 { + reg = <1>; + label = "lan4"; + phy-handle = <&switch1phy1>; + }; + + port@2 { + reg = <2>; + label = "lan5"; + phy-handle = <&switch1phy2>; + }; + + switch1port5: port@5 { + reg = <5>; + label = "dsa"; + link = <&switch2port9>; + phy-mode = "rgmii-txid"; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + switch1port6: port@6 { + reg = <6>; + label = "dsa"; + phy-mode = "rgmii-txid"; + link = <&switch0port5>; + }; + }; + mdio { + #address-cells = <1>; + #size-cells = <0>; + switch1phy0: switch1phy0@0 { + reg = <0>; + }; + switch1phy1: switch1phy0@1 { + reg = <1>; + }; + switch1phy2: switch1phy0@2 { + reg = <2>; + }; + }; + }; + }; + + mdio_mux_4: mdio@4 { + #address-cells = <1>; + #size-cells = <0>; + reg = <4>; + + switch2: switch2@0 { + compatible = "marvell,mv88e6085"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + dsa,member = <0 2>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + label = "lan6"; + }; + + port@1 { + reg = <1>; + label = "lan7"; + }; + + port@2 { + reg = <2>; + label = "lan8"; + }; + + port@3 { + reg = <3>; + label = "optical3"; + fixed-link { + speed = <1000>; + full-duplex; + link-gpios = <&gpio6 2 + GPIO_ACTIVE_HIGH>; + }; + }; + + port@4 { + reg = <4>; + label = "optical4"; + fixed-link { + speed = <1000>; + full-duplex; + link-gpios = <&gpio6 3 + GPIO_ACTIVE_HIGH>; + }; + }; + + switch2port9: port@9 { + reg = <9>; + label = "dsa"; + phy-mode = "rgmii-txid"; + link = <&switch1port5 + &switch0port5>; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + }; + }; + + mdio_mux_8: mdio@8 { + reg = <8>; + #address-cells = <1>; + #size-cells = <0>; + }; + }; + + spi0 { + compatible = "spi-gpio"; + pinctrl-0 = <&pinctrl_gpio_spi0>; + pinctrl-names = "default"; + #address-cells = <1>; + #size-cells = <0>; + gpio-sck = <&gpio1 12 GPIO_ACTIVE_HIGH>; + gpio-mosi = <&gpio1 11 GPIO_ACTIVE_HIGH>; + gpio-miso = <&gpio1 10 GPIO_ACTIVE_HIGH>; + cs-gpios = <&gpio1 9 GPIO_ACTIVE_HIGH + &gpio1 8 GPIO_ACTIVE_HIGH>; + num-chipselects = <2>; + + m25p128@0 { + compatible = "m25p128", "jedec,spi-nor"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0>; + spi-max-frequency = <1000000>; + }; + + at93c46d@1 { + compatible = "atmel,at93c46d"; + pinctrl-0 = <&pinctrl_gpio_e6185_eeprom_sel>; + pinctrl-names = "default"; + #address-cells = <0>; + #size-cells = <0>; + reg = <1>; + spi-max-frequency = <500000>; + spi-cs-high; + data-size = <16>; + select-gpios = <&gpio4 4 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&i2c0 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c0>; + status = "okay"; + + gpio5: pca9554@20 { + compatible = "nxp,pca9554"; + reg = <0x20>; + gpio-controller; + #gpio-cells = <2>; + + }; + + gpio6: pca9554@22 { + compatible = "nxp,pca9554"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pca9554_22>; + reg = <0x22>; + gpio-controller; + #gpio-cells = <2>; + interrupt-parent = <&gpio2>; + interrupts = <2 IRQ_TYPE_LEVEL_LOW>; + }; +}; + +&i2c2 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; + + tca9548@70 { + compatible = "nxp,pca9548"; + pinctrl-0 = <&pinctrl_i2c_mux_reset>; + pinctrl-names = "default"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x70>; + reset-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>; + + i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + sfp1: at24c04@50 { + compatible = "atmel,24c02"; + reg = <0x50>; + }; + }; + + i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + sfp2: at24c04@50 { + compatible = "atmel,24c02"; + reg = <0x50>; + }; + }; + + i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <2>; + + sfp3: at24c04@50 { + compatible = "atmel,24c02"; + reg = <0x50>; + }; + }; + + i2c@3 { + #address-cells = <1>; + #size-cells = <0>; + reg = <3>; + + sfp4: at24c04@50 { + compatible = "atmel,24c02"; + reg = <0x50>; + }; + }; + + i2c@4 { + #address-cells = <1>; + #size-cells = <0>; + reg = <4>; + }; + }; +}; + + +&iomuxc { + pinctrl_gpio_e6185_eeprom_sel: pinctrl-gpio-e6185-eeprom-spi0 { + fsl,pins = < + VF610_PAD_PTE27__GPIO_132 0x33e2 + >; + }; + + pinctrl_gpio_spi0: pinctrl-gpio-spi0 { + fsl,pins = < + VF610_PAD_PTB22__GPIO_44 0x33e2 + VF610_PAD_PTB21__GPIO_43 0x33e2 + VF610_PAD_PTB20__GPIO_42 0x33e1 + VF610_PAD_PTB19__GPIO_41 0x33e2 + VF610_PAD_PTB18__GPIO_40 0x33e2 + >; + }; + + pinctrl_mdio_mux: pinctrl-mdio-mux { + fsl,pins = < + VF610_PAD_PTA18__GPIO_8 0x31c2 + VF610_PAD_PTA19__GPIO_9 0x31c2 + VF610_PAD_PTB2__GPIO_24 0x31c2 + VF610_PAD_PTB3__GPIO_25 0x31c2 + >; + }; + + pinctrl_pca9554_22: pinctrl-pca95540-22 { + fsl,pins = < + VF610_PAD_PTB28__GPIO_98 0x219d + >; + }; +}; + +/* + * ============================================================= + * End of shared part + * ============================================================= +*/ diff --git a/arch/arm/dts/vf610-zii-dev-rev-c.dts b/arch/arm/dts/vf610-zii-dev-rev-c.dts new file mode 100644 index 0000000000..5228942632 --- /dev/null +++ b/arch/arm/dts/vf610-zii-dev-rev-c.dts @@ -0,0 +1,445 @@ +/* + * Copyright (C) 2015, 2016 Zodiac Inflight Innovations + * + * Based on an original 'vf610-twr.dts' which is Copyright 2015, + * Freescale Semiconductor, Inc. + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; + +#include "vf610-zii-dev.dtsi" + +/* + * ============================================================= + * The following code is shared with Linux kernel and should be + * removed once it trickles down from there eventually + * ============================================================= + */ + +/ { + model = "ZII VF610 Development Board, Rev C"; + compatible = "zii,vf610dev-c", "zii,vf610dev", "fsl,vf610"; + + mdio-mux { + compatible = "mdio-mux-gpio"; + pinctrl-0 = <&pinctrl_mdio_mux>; + pinctrl-names = "default"; + gpios = <&gpio0 8 GPIO_ACTIVE_HIGH + &gpio0 9 GPIO_ACTIVE_HIGH + &gpio0 25 GPIO_ACTIVE_HIGH>; + mdio-parent-bus = <&mdio1>; + #address-cells = <1>; + #size-cells = <0>; + + mdio_mux_1: mdio@1 { + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + + switch0: switch0@0 { + compatible = "marvell,mv88e6190"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + dsa,member = <0 0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "cpu"; + ethernet = <&fec1>; + fixed-link { + speed = <100>; + full-duplex; + }; + }; + + port@1 { + reg = <1>; + label = "lan1"; + }; + + port@2 { + reg = <2>; + label = "lan2"; + }; + + port@3 { + reg = <3>; + label = "lan3"; + }; + + port@4 { + reg = <4>; + label = "lan4"; + }; + + switch0port10: port@10 { + reg = <10>; + label = "dsa"; + phy-mode = "xgmii"; + link = <&switch1port10>; + }; + }; + }; + }; + + mdio_mux_2: mdio@2 { + reg = <2>; + #address-cells = <1>; + #size-cells = <0>; + + switch1: switch1@0 { + compatible = "marvell,mv88e6190"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + dsa,member = <0 1>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + reg = <1>; + label = "lan5"; + }; + + port@2 { + reg = <2>; + label = "lan6"; + }; + + port@3 { + reg = <3>; + label = "lan7"; + }; + + port@4 { + reg = <4>; + label = "lan8"; + }; + + + switch1port10: port@10 { + reg = <10>; + label = "dsa"; + phy-mode = "xgmii"; + link = <&switch0port10>; + }; + }; + }; + }; + + mdio_mux_4: mdio@4 { + reg = <4>; + #address-cells = <1>; + #size-cells = <0>; + }; + }; +}; + +&dspi0 { + bus-num = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_dspi0>; + status = "okay"; + spi-num-chipselects = <2>; + + m25p128@0 { + compatible = "m25p128", "jedec,spi-nor"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0>; + spi-max-frequency = <50000000>; + }; + + atzb-rf-233@1 { + compatible = "atmel,at86rf233"; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctr_atzb_rf_233>; + + spi-max-frequency = <7500000>; + reg = <1>; + interrupts = <4 IRQ_TYPE_LEVEL_HIGH>; + interrupt-parent = <&gpio3>; + xtal-trim = /bits/ 8 <0x06>; + + sleep-gpio = <&gpio0 24 GPIO_ACTIVE_HIGH>; + reset-gpio = <&gpio6 10 GPIO_ACTIVE_HIGH>; + + fsl,spi-cs-sck-delay = <180>; + fsl,spi-sck-cs-delay = <250>; + }; +}; + +&dspi2 { + bus-num = <2>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_dspi2>; + status = "okay"; + spi-num-chipselects = <2>; +}; + +&i2c0 { + /* + * U712 + * + * Exposed signals: + * P1 - WE2_CMD + * P2 - WE2_CLK + */ + gpio5: pca9557@18 { + compatible = "nxp,pca9557"; + reg = <0x18>; + gpio-controller; + #gpio-cells = <2>; + }; + + /* + * U121 + * + * Exposed signals: + * I/O0 - ENET_SWR_EN + * I/O1 - ESW1_RESETn + * I/O2 - ARINC_RESET + * I/O3 - DD1_IO_RESET + * I/O4 - ESW2_RESETn + * I/O5 - ESW3_RESETn + * I/O6 - ESW4_RESETn + * I/O8 - TP909 + * I/O9 - FEM_SEL + * I/O10 - WIFI_RESETn + * I/O11 - PHY_RSTn + * I/O12 - OPT1_SD + * I/O13 - OPT2_SD + * I/O14 - OPT1_TX_DIS + * I/O15 - OPT2_TX_DIS + */ + gpio6: sx1503@20 { + compatible = "semtech,sx1503q"; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sx1503_20>; + #gpio-cells = <2>; + #interrupt-cells = <2>; + reg = <0x20>; + interrupt-parent = <&gpio0>; + interrupts = <23 IRQ_TYPE_EDGE_FALLING>; + gpio-controller; + interrupt-controller; + + enet_swr_en { + gpio-hog; + gpios = <0 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "enet-swr-en"; + }; + }; + + /* + * U715 + * + * Exposed signals: + * IO0 - WE1_CLK + * IO1 - WE1_CMD + */ + gpio7: pca9554@22 { + compatible = "nxp,pca9554"; + reg = <0x22>; + gpio-controller; + #gpio-cells = <2>; + + }; +}; + +&i2c1 { + at24mac602@00 { + compatible = "atmel,24c02"; + reg = <0x50>; + read-only; + }; +}; + +&i2c2 { + tca9548@70 { + compatible = "nxp,pca9548"; + pinctrl-0 = <&pinctrl_i2c_mux_reset>; + pinctrl-names = "default"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x70>; + reset-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>; + + i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + }; + + i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + sfp2: at24c04@50 { + compatible = "atmel,24c02"; + reg = <0x50>; + }; + }; + + i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <2>; + + sfp3: at24c04@50 { + compatible = "atmel,24c02"; + reg = <0x50>; + }; + }; + + i2c@3 { + #address-cells = <1>; + #size-cells = <0>; + reg = <3>; + }; + }; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>; + status = "okay"; +}; + +&gpio0 { + eth0_intrp { + gpio-hog; + gpios = <23 GPIO_ACTIVE_HIGH>; + input; + line-name = "sx1503-irq"; + }; +}; + +&gpio3 { + eth0_intrp { + gpio-hog; + gpios = <2 GPIO_ACTIVE_HIGH>; + input; + line-name = "eth0-intrp"; + }; +}; + +&fec0 { + mdio { + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + + ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec0_phy_int>; + + interrupt-parent = <&gpio3>; + interrupts = <2 IRQ_TYPE_LEVEL_LOW>; + reg = <0>; + }; + }; +}; + +&iomuxc { + pinctr_atzb_rf_233: pinctrl-atzb-rf-233 { + fsl,pins = < + VF610_PAD_PTB2__GPIO_24 0x31c2 + VF610_PAD_PTE27__GPIO_132 0x33e2 + >; + }; + + + pinctrl_sx1503_20: pinctrl-sx1503-20 { + fsl,pins = < + VF610_PAD_PTB1__GPIO_23 0x219d + >; + }; + + pinctrl_uart3: uart3grp { + fsl,pins = < + VF610_PAD_PTA20__UART3_TX 0x21a2 + VF610_PAD_PTA21__UART3_RX 0x21a1 + >; + }; + + pinctrl_mdio_mux: pinctrl-mdio-mux { + fsl,pins = < + VF610_PAD_PTA18__GPIO_8 0x31c2 + VF610_PAD_PTA19__GPIO_9 0x31c2 + VF610_PAD_PTB3__GPIO_25 0x31c2 + >; + }; + + pinctrl_fec0_phy_int: pinctrl-fec0-phy-int { + fsl,pins = < + VF610_PAD_PTB28__GPIO_98 0x219d + >; + }; +}; + +/* + * ============================================================= + * End of shared part + * ============================================================= + */ + + +&dspi0 { + m25p128@0 { + partition@0 { + label = "bootloader"; + reg = <0x0 0x100000>; + }; + }; +}; diff --git a/arch/arm/dts/vf610-zii-dev.dtsi b/arch/arm/dts/vf610-zii-dev.dtsi new file mode 100644 index 0000000000..dae077cedb --- /dev/null +++ b/arch/arm/dts/vf610-zii-dev.dtsi @@ -0,0 +1,436 @@ +/* + * Copyright (C) 2015, 2016 Zodiac Inflight Innovations + * + * Based on an original 'vf610-twr.dts' which is Copyright 2015, + * Freescale Semiconductor, Inc. + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use +n * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + + +/* + * ============================================================= + * The following code is shared with Linux kernel and should be + * removed once it trickles down from there eventually + * ============================================================= + */ + +#include <arm/vf610.dtsi> + +/ { + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory { + reg = <0x80000000 0x20000000>; + }; + + gpio-leds { + compatible = "gpio-leds"; + pinctrl-0 = <&pinctrl_leds_debug>; + pinctrl-names = "default"; + + debug { + label = "zii:green:debug1"; + gpios = <&gpio2 10 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + }; + }; + + reg_vcc_3v3_mcu: regulator-vcc-3v3-mcu { + compatible = "regulator-fixed"; + regulator-name = "vcc_3v3_mcu"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + usb0_vbus: regulator-usb0-vbus { + compatible = "regulator-fixed"; + pinctrl-0 = <&pinctrl_usb_vbus>; + regulator-name = "usb_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + gpio = <&gpio0 6 0>; + }; +}; + +&adc0 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_adc0_ad5>; + vref-supply = <®_vcc_3v3_mcu>; + status = "okay"; +}; + +&edma0 { + status = "okay"; +}; + +&esdhc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_esdhc1>; + bus-width = <4>; + status = "okay"; +}; + +&fec0 { + phy-mode = "rmii"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec0>; + status = "okay"; +}; + +&fec1 { + phy-mode = "rmii"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec1>; + status = "okay"; + + fixed-link { + speed = <100>; + full-duplex; + }; + + mdio1: mdio { + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + }; +}; + +&i2c0 { + clock-frequency = <100000>; + pinctrl-names = "default", "gpio"; + pinctrl-0 = <&pinctrl_i2c0>; + pinctrl-1 = <&pinctrl_i2c0_gpio>; + scl-gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>; + sda-gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>; + status = "okay"; + + lm75@48 { + compatible = "national,lm75"; + reg = <0x48>; + }; + + at24c04@50 { + compatible = "atmel,24c04"; + reg = <0x50>; + }; + + at24c04@52 { + compatible = "atmel,24c04"; + reg = <0x52>; + }; + + ds1682@6b { + compatible = "dallas,ds1682"; + reg = <0x6b>; + }; +}; + +&i2c1 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; +}; + +&i2c2 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart0>; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + status = "okay"; +}; + +&usbdev0 { + disable-over-current; + vbus-supply = <&usb0_vbus>; + dr_mode = "host"; + status = "okay"; +}; + +&usbh1 { + disable-over-current; + status = "okay"; +}; + +&usbmisc0 { + status = "okay"; +}; + +&usbmisc1 { + status = "okay"; +}; + +&usbphy0 { + status = "okay"; +}; + +&usbphy1 { + status = "okay"; +}; + +&iomuxc { + pinctrl_adc0_ad5: adc0ad5grp { + fsl,pins = < + VF610_PAD_PTC30__ADC0_SE5 0x00a1 + >; + }; + + pinctrl_dspi0: dspi0grp { + fsl,pins = < + VF610_PAD_PTB18__DSPI0_CS1 0x1182 + VF610_PAD_PTB19__DSPI0_CS0 0x1182 + VF610_PAD_PTB20__DSPI0_SIN 0x1181 + VF610_PAD_PTB21__DSPI0_SOUT 0x1182 + VF610_PAD_PTB22__DSPI0_SCK 0x1182 + >; + }; + + pinctrl_dspi2: dspi2grp { + fsl,pins = < + VF610_PAD_PTD31__DSPI2_CS1 0x1182 + VF610_PAD_PTD30__DSPI2_CS0 0x1182 + VF610_PAD_PTD29__DSPI2_SIN 0x1181 + VF610_PAD_PTD28__DSPI2_SOUT 0x1182 + VF610_PAD_PTD27__DSPI2_SCK 0x1182 + >; + }; + + pinctrl_esdhc1: esdhc1grp { + fsl,pins = < + VF610_PAD_PTA24__ESDHC1_CLK 0x31ef + VF610_PAD_PTA25__ESDHC1_CMD 0x31ef + VF610_PAD_PTA26__ESDHC1_DAT0 0x31ef + VF610_PAD_PTA27__ESDHC1_DAT1 0x31ef + VF610_PAD_PTA28__ESDHC1_DATA2 0x31ef + VF610_PAD_PTA29__ESDHC1_DAT3 0x31ef + VF610_PAD_PTA7__GPIO_134 0x219d + >; + }; + + pinctrl_fec0: fec0grp { + fsl,pins = < + VF610_PAD_PTC0__ENET_RMII0_MDC 0x30d2 + VF610_PAD_PTC1__ENET_RMII0_MDIO 0x30d3 + VF610_PAD_PTC2__ENET_RMII0_CRS 0x30d1 + VF610_PAD_PTC3__ENET_RMII0_RXD1 0x30d1 + VF610_PAD_PTC4__ENET_RMII0_RXD0 0x30d1 + VF610_PAD_PTC5__ENET_RMII0_RXER 0x30d1 + VF610_PAD_PTC6__ENET_RMII0_TXD1 0x30d2 + VF610_PAD_PTC7__ENET_RMII0_TXD0 0x30d2 + VF610_PAD_PTC8__ENET_RMII0_TXEN 0x30d2 + >; + }; + + pinctrl_fec1: fec1grp { + fsl,pins = < + VF610_PAD_PTA6__RMII_CLKIN 0x30d1 + VF610_PAD_PTC9__ENET_RMII1_MDC 0x30d2 + VF610_PAD_PTC10__ENET_RMII1_MDIO 0x30d3 + VF610_PAD_PTC11__ENET_RMII1_CRS 0x30d1 + VF610_PAD_PTC12__ENET_RMII1_RXD1 0x30d1 + VF610_PAD_PTC13__ENET_RMII1_RXD0 0x30d1 + VF610_PAD_PTC14__ENET_RMII1_RXER 0x30d1 + VF610_PAD_PTC15__ENET_RMII1_TXD1 0x30d2 + VF610_PAD_PTC16__ENET_RMII1_TXD0 0x30d2 + VF610_PAD_PTC17__ENET_RMII1_TXEN 0x30d2 + >; + }; + + pinctrl_gpio_spi0: pinctrl-gpio-spi0 { + fsl,pins = < + VF610_PAD_PTB22__GPIO_44 0x33e2 + VF610_PAD_PTB21__GPIO_43 0x33e2 + VF610_PAD_PTB20__GPIO_42 0x33e1 + VF610_PAD_PTB19__GPIO_41 0x33e2 + VF610_PAD_PTB18__GPIO_40 0x33e2 + >; + }; + + pinctrl_i2c_mux_reset: pinctrl-i2c-mux-reset { + fsl,pins = < + VF610_PAD_PTE14__GPIO_119 0x31c2 + >; + }; + + pinctrl_i2c0: i2c0grp { + fsl,pins = < + VF610_PAD_PTB14__I2C0_SCL 0x37ff + VF610_PAD_PTB15__I2C0_SDA 0x37ff + >; + }; + + pinctrl_i2c0_gpio: i2c0grp-gpio { + fsl,pins = < + VF610_PAD_PTB14__GPIO_36 0x31c2 + VF610_PAD_PTB15__GPIO_37 0x31c2 + >; + }; + + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + VF610_PAD_PTB16__I2C1_SCL 0x37ff + VF610_PAD_PTB17__I2C1_SDA 0x37ff + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + VF610_PAD_PTA22__I2C2_SCL 0x37ff + VF610_PAD_PTA23__I2C2_SDA 0x37ff + >; + }; + + pinctrl_leds_debug: pinctrl-leds-debug { + fsl,pins = < + VF610_PAD_PTD20__GPIO_74 0x31c2 + >; + }; + + pinctrl_qspi0: qspi0grp { + fsl,pins = < + VF610_PAD_PTD7__QSPI0_B_QSCK 0x31c3 + VF610_PAD_PTD8__QSPI0_B_CS0 0x31ff + VF610_PAD_PTD9__QSPI0_B_DATA3 0x31c3 + VF610_PAD_PTD10__QSPI0_B_DATA2 0x31c3 + VF610_PAD_PTD11__QSPI0_B_DATA1 0x31c3 + VF610_PAD_PTD12__QSPI0_B_DATA0 0x31c3 + >; + }; + + pinctrl_uart0: uart0grp { + fsl,pins = < + VF610_PAD_PTB10__UART0_TX 0x21a2 + VF610_PAD_PTB11__UART0_RX 0x21a1 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + VF610_PAD_PTB23__UART1_TX 0x21a2 + VF610_PAD_PTB24__UART1_RX 0x21a1 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + VF610_PAD_PTD0__UART2_TX 0x21a2 + VF610_PAD_PTD1__UART2_RX 0x21a1 + >; + }; + + pinctrl_usb_vbus: pinctrl-usb-vbus { + fsl,pins = < + VF610_PAD_PTA16__GPIO_6 0x31c2 + >; + }; + + pinctrl_usb0_host: usb0-host-grp { + fsl,pins = < + VF610_PAD_PTD6__GPIO_85 0x0062 + >; + }; +}; + +/* + * ============================================================= + * End of shared part + * ============================================================= + */ + +/ { + audio_ext: mclk_osc { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <0>; + }; + + enet_ext: eth_osc { + compatible = "fixed-clock"; + clock-output-names = "enet_ext"; + #clock-cells = <0>; + clock-frequency = <50000000>; + }; + + anaclk1: anaclk1 { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <0>; + }; +}; + +&clks { + clocks = <&sxosc>, <&fxosc>, <&enet_ext>, <&audio_ext>, <&anaclk1>, + <&clks VF610_CLK_SYS_BUS>, <&clks VF610_CLK_PLATFORM_BUS>, + <&clks VF610_CLK_IPG_BUS>, <&clks VF610_CLK_DDRMC>; + clock-names = "sxosc", "fxosc", "enet_ext", "audio_ext", "anaclk1", + "cpu", "bus", "ipg", "ddr"; + + assigned-clocks = <&clks VF610_CLK_ENET_SEL>, + <&clks VF610_CLK_ENET_TS_SEL>; + assigned-clock-parents = <&clks VF610_CLK_ENET_EXT>, + <&clks VF610_CLK_ENET_EXT>; +}; + +&ocotp { + barebox,provide-mac-address = <&fec0 0x620>, + <&fec1 0x640>; +}; diff --git a/arch/arm/dts/vf610-zii-scu4-aib-rev-c.dts b/arch/arm/dts/vf610-zii-scu4-aib-rev-c.dts new file mode 100644 index 0000000000..d10f460e32 --- /dev/null +++ b/arch/arm/dts/vf610-zii-scu4-aib-rev-c.dts @@ -0,0 +1,457 @@ +/* + * Copyright (C) 2015, 2016 Zodiac Inflight Innovations + * + * Based on an original 'vf610-twr.dts' which is Copyright 2015, + * Freescale Semiconductor, Inc. + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; + +#include "vf610-zii-dev.dtsi" + +/ { + model = "ZII VF610 SCU4 AIB, Rev C"; + compatible = "zii,vf610scu4-aib-c", "zii,vf610dev", "fsl,vf610"; + + chosen { + bootargs = "console=ttyLP0,115200n8"; + }; + + gpio-leds { + debug { + gpios = <&gpio3 0 GPIO_ACTIVE_HIGH>; + }; + }; + + mdio-mux { + compatible = "mdio-mux-gpio"; + pinctrl-0 = <&pinctrl_mdio_mux>; + pinctrl-names = "default"; + gpios = <&gpio4 4 GPIO_ACTIVE_HIGH + &gpio4 5 GPIO_ACTIVE_HIGH + &gpio3 30 GPIO_ACTIVE_HIGH + &gpio3 31 GPIO_ACTIVE_HIGH>; + mdio-parent-bus = <&mdio1>; + #address-cells = <1>; + #size-cells = <0>; + + mdio_mux_1: mdio@1 { + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + }; + + mdio_mux_2: mdio@2 { + reg = <2>; + #address-cells = <1>; + #size-cells = <0>; + }; + + mdio_mux_4: mdio@4 { + reg = <4>; + #address-cells = <1>; + #size-cells = <0>; + }; + + mdio_mux_8: mdio@8 { + reg = <8>; + #address-cells = <1>; + #size-cells = <0>; + }; + }; + + spi2 { + compatible = "spi-gpio"; + pinctrl-0 = <&pinctrl_dspi2>; + pinctrl-names = "default"; + #address-cells = <1>; + #size-cells = <0>; + + gpio-sck = <&gpio2 3 GPIO_ACTIVE_HIGH>; + gpio-mosi = <&gpio2 2 GPIO_ACTIVE_HIGH>; + gpio-miso = <&gpio2 1 GPIO_ACTIVE_HIGH>; + cs-gpios = <&gpio2 0 GPIO_ACTIVE_HIGH>; + num-chipselects = <1>; + + at93c46d@0 { + compatible = "atmel,at93c46d"; + #address-cells = <0>; + #size-cells = <0>; + reg = <0>; + spi-max-frequency = <500000>; + spi-cs-high; + data-size = <16>; + select-gpios = <&gpio2 4 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&dspi0 { + pinctrl-0 = <&pinctrl_dspi0>, <&pinctrl_dspi0_cs_4_5>; + pinctrl-names = "default"; + status = "okay"; +}; + +&dspi1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_dspi1>; + status = "okay"; + + m25p128@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "m25p128", "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <50000000>; + + partition@0 { + label = "m25p128-0"; + reg = <0x0 0x01000000>; + }; + }; + + m25p128@1 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "m25p128", "jedec,spi-nor"; + reg = <1>; + spi-max-frequency = <50000000>; + + partition@0 { + label = "m25p128-1"; + reg = <0x0 0x01000000>; + }; + }; +}; + +&esdhc0 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_esdhc0>; + bus-width = <8>; + status = "okay"; +}; + +&fec0 { + status = "disabled"; +}; + +&i2c0 { + /* Reset Signals */ + gpio5: pca9505@20 { + compatible = "nxp,pca9554"; + reg = <0x20>; + gpio-controller; + #gpio-cells = <2>; + }; + + /* Board Revision */ + gpio6: pca9505@22 { + compatible = "nxp,pca9554"; + reg = <0x22>; + gpio-controller; + #gpio-cells = <2>; + }; +}; + +&i2c1 { + /* Wireless 2 */ + gpio8: pca9554@18 { + compatible = "nxp,pca9557"; + reg = <0x18>; + gpio-controller; + #gpio-cells = <2>; + }; + + /* Wireless 1 */ + gpio7: pca9554@24 { + compatible = "nxp,pca9554"; + reg = <0x24>; + gpio-controller; + #gpio-cells = <2>; + }; + + /* AIB voltage monitor */ + adt7411@4a { + compatible = "adi,adt7411"; + reg = <0x4a>; + }; +}; + +&i2c2 { + /* FIB voltage monitor */ + adt7411@4a { + compatible = "adi,adt7411"; + reg = <0x4a>; + }; + + lm75_swb { + compatible = "national,lm75"; + reg = <0x4e>; + }; + + lm75_swa { + compatible = "national,lm75"; + reg = <0x4f>; + }; + + /* FIB Nameplate */ + at24c08@57 { + compatible = "atmel,24c08"; + reg = <0x57>; + }; + + tca9548@70 { + compatible = "nxp,pca9548"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x70>; + + i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + sff0: at24c04@50 { + compatible = "atmel,24c04"; + reg = <0x50>; + }; + }; + + i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <2>; + + sff1: at24c04@50 { + compatible = "atmel,24c04"; + reg = <0x50>; + }; + }; + + i2c@3 { + #address-cells = <1>; + #size-cells = <0>; + reg = <3>; + + sff2: at24c04@50 { + compatible = "atmel,24c04"; + reg = <0x50>; + }; + }; + + i2c@4 { + #address-cells = <1>; + #size-cells = <0>; + reg = <4>; + + sff3: at24c04@50 { + compatible = "atmel,24c04"; + reg = <0x50>; + }; + }; + + i2c@5 { + #address-cells = <1>; + #size-cells = <0>; + reg = <5>; + + sff4: at24c04@50 { + compatible = "atmel,24c04"; + reg = <0x50>; + }; + }; + }; + + + tca9548@71 { + compatible = "nxp,pca9548"; + reg = <0x71>; + #address-cells = <1>; + #size-cells = <0>; + + i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + sff5: at24c04@50 { + compatible = "atmel,24c04"; + reg = <0x50>; + }; + }; + + i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <2>; + + sff6: at24c04@50 { + compatible = "atmel,24c04"; + reg = <0x50>; + }; + }; + + i2c@3 { + #address-cells = <1>; + #size-cells = <0>; + reg = <3>; + + sff7: at24c04@50 { + compatible = "atmel,24c04"; + reg = <0x50>; + }; + + }; + + i2c@4 { + #address-cells = <1>; + #size-cells = <0>; + reg = <4>; + + sff8: at24c04@50 { + compatible = "atmel,24c04"; + reg = <0x50>; + }; + }; + + i2c@5 { + #address-cells = <1>; + #size-cells = <0>; + reg = <5>; + + sff9: at24c04@50 { + compatible = "atmel,24c04"; + reg = <0x50>; + }; + }; + }; +}; + +&uart1 { + linux,rs485-enabled-at-boot-time; + pinctrl-0 = <&pinctrl_uart1>, <&pinctrl_uart1_rts>; +}; + +&uart2 { + linux,rs485-enabled-at-boot-time; + pinctrl-0 = <&pinctrl_uart2>, <&pinctrl_uart2_rts>; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpo_public>; + + + pinctrl_gpo_public: gpopubgrp { + fsl,pins = < + VF610_PAD_PTE2__GPIO_107 0x2062 + VF610_PAD_PTE3__GPIO_108 0x2062 + VF610_PAD_PTE4__GPIO_109 0x2062 + VF610_PAD_PTE5__GPIO_110 0x2062 + VF610_PAD_PTE6__GPIO_111 0x2062 + >; + }; + + pinctrl_dspi0_cs_4_5: dspi0grp-cs-4-5 { + fsl,pins = < + VF610_PAD_PTB13__DSPI0_CS4 0x1182 + VF610_PAD_PTB12__DSPI0_CS5 0x1182 + >; + }; + + pinctrl_dspi1: dspi1grp { + fsl,pins = < + VF610_PAD_PTD5__DSPI1_CS0 0x1182 + VF610_PAD_PTD4__DSPI1_CS1 0x1182 + VF610_PAD_PTC6__DSPI1_SIN 0x1181 + VF610_PAD_PTC7__DSPI1_SOUT 0x1182 + VF610_PAD_PTC8__DSPI1_SCK 0x1182 + >; + }; + + pinctrl_esdhc0: esdhc0grp { + fsl,pins = < + VF610_PAD_PTC0__ESDHC0_CLK 0x31ef + VF610_PAD_PTC1__ESDHC0_CMD 0x31ef + VF610_PAD_PTC2__ESDHC0_DAT0 0x31ef + VF610_PAD_PTC3__ESDHC0_DAT1 0x31ef + VF610_PAD_PTC4__ESDHC0_DAT2 0x31ef + VF610_PAD_PTC5__ESDHC0_DAT3 0x31ef + VF610_PAD_PTD23__ESDHC0_DAT4 0x31ef + VF610_PAD_PTD22__ESDHC0_DAT5 0x31ef + VF610_PAD_PTD21__ESDHC0_DAT6 0x31ef + VF610_PAD_PTD20__ESDHC0_DAT7 0x31ef + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + VF610_PAD_PTA30__I2C3_SCL 0x37ff + VF610_PAD_PTA31__I2C3_SDA 0x37ff + >; + }; + + pinctrl_leds_debug: pinctrl-leds-debug { + fsl,pins = < + VF610_PAD_PTB26__GPIO_96 0x31c2 + >; + }; + + pinctrl_uart1_rts: uart1grp-rts { + fsl,pins = < + VF610_PAD_PTB25__UART1_RTS 0x2062 + >; + }; + + pinctrl_uart2_rts: uart2grp-rts { + fsl,pins = < + VF610_PAD_PTD2__UART2_RTS 0x2062 + >; + }; + + pinctrl_mdio_mux: pinctrl-mdio-mux { + fsl,pins = < + VF610_PAD_PTE27__GPIO_132 0x31c2 + VF610_PAD_PTE28__GPIO_133 0x31c2 + VF610_PAD_PTE21__GPIO_126 0x31c2 + VF610_PAD_PTE22__GPIO_127 0x31c2 + >; + }; +}; diff --git a/arch/arm/dts/vf610-zii-spu3-rev-a.dts b/arch/arm/dts/vf610-zii-spu3-rev-a.dts new file mode 100644 index 0000000000..25ab26ddfd --- /dev/null +++ b/arch/arm/dts/vf610-zii-spu3-rev-a.dts @@ -0,0 +1,140 @@ +/* + * Copyright (C) 2015, 2016 Zodiac Inflight Innovations + * + * Based on an original 'vf610-twr.dts' which is Copyright 2015, + * Freescale Semiconductor, Inc. + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "vf610-zii-dev.dtsi" + + +/ { + model = "ZII VF610 SPU3 Switch Management Board"; + compatible = "zii,vf610spu3-a", "zii,vf610dev", "fsl,vf610"; + + aliases { + /delete-property/ serial2; + }; + + gpio-leds { + debug { + gpios = <&gpio2 18 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&dspi1 { + bus-num = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_dspi1>; + status = "okay"; + + m25p128@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "m25p128", "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <50000000>; + + partition@0 { + label = "m25p128-0"; + reg = <0x0 0x01000000>; + }; + }; +}; + +&esdhc0 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_esdhc0>; + bus-width = <8>; + status = "okay"; +}; + +&fec0 { + status = "disabled"; +}; + +&i2c0 { + /* Board Revision */ + gpio6: pca9505@22 { + compatible = "nxp,pca9554"; + reg = <0x22>; + gpio-controller; + #gpio-cells = <2>; + }; +}; + +/delete-node/ &i2c1; +/delete-node/ &i2c2; +/delete-node/ &uart2; + +&iomuxc { + pinctrl_dspi1: dspi1grp { + fsl,pins = < + VF610_PAD_PTD5__DSPI1_CS0 0x1182 + VF610_PAD_PTD4__DSPI1_CS1 0x1182 + VF610_PAD_PTC6__DSPI1_SIN 0x1181 + VF610_PAD_PTC7__DSPI1_SOUT 0x1182 + VF610_PAD_PTC8__DSPI1_SCK 0x1182 + >; + }; + + pinctrl_esdhc0: esdhc0grp { + fsl,pins = < + VF610_PAD_PTC0__ESDHC0_CLK 0x31ef + VF610_PAD_PTC1__ESDHC0_CMD 0x31ef + VF610_PAD_PTC2__ESDHC0_DAT0 0x31ef + VF610_PAD_PTC3__ESDHC0_DAT1 0x31ef + VF610_PAD_PTC4__ESDHC0_DAT2 0x31ef + VF610_PAD_PTC5__ESDHC0_DAT3 0x31ef + VF610_PAD_PTD23__ESDHC0_DAT4 0x31ef + VF610_PAD_PTD22__ESDHC0_DAT5 0x31ef + VF610_PAD_PTD21__ESDHC0_DAT6 0x31ef + VF610_PAD_PTD20__ESDHC0_DAT7 0x31ef + >; + }; + + pinctrl_leds_debug: pinctrl-leds-debug { + fsl,pins = < + VF610_PAD_PTD3__GPIO_82 0x31c2 + >; + }; +}; |