ARM: initial ConnectCore® i.MX51 board support

This patch adds support for ConnectCore® i.MX51 board from Digi International.
A separate option includes support for debugging board for this module.
Some code taken from the bootloader U-Boot and patch from Digi.
Functional of Ethernet not tested yet.

barebox 2012.05.0-00316-g4024d9c-dirty #0 Wed Jun 6 13:08:25 MSK 2012

Board: ConnectCore i.MX51
Module Variant: i.MX515@600MHz, PHY, Acceleromter (0x0b)
Module HW Rev : 02
Module Serial : B111156789
mc13xxx-spi@mc13xxx-spi0: Found MC13892 ID: 0x0045d0 [Rev: 2.0a]
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron NAND 256MiB 3,3V 8-bit)
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
nand_read_bbt: Bad block at 0x00ce0000
nand_read_bbt: Bad block at 0x05bc0000
nand_read_bbt: Bad block at 0x0bc40000
ehci@ehci0: USB EHCI 1.00
detected i.MX51 rev 3.0
imx-esdhc@mci0: registered as mci0
imx-esdhc@mci1: registered as mci1
Malloc space: 0x95f00000 -> 0x97efffff (size 32 MB)
Stack space : 0x95ef8000 -> 0x95f00000 (size 32 kB)
envfs: wrong magic on /dev/env0
no valid environment found on /dev/env0. Using default environment
running /env/bin/init...

Hit any key to stop autoboot: 3
barebox@ConnectCore i.MX51:/

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

11 files changed, 843 insertions, 0 deletions

diff --git a/arch/arm/Makefile b/arch/arm/Makefile
index bd684dc23a..1225df782d 100644
--- a/arch/arm/Makefile
+++ b/arch/arm/Makefile
@@ -136,6 +136,7 @@ board-$(CONFIG_MACH_TQMA53)			:= tqma53
 board-$(CONFIG_MACH_TX51)			:= karo-tx51
 board-$(CONFIG_MACH_MX6Q_ARM2)			:= freescale-mx6-arm2
 board-$(CONFIG_MACH_TOSHIBA_AC100)		:= toshiba-ac100
+board-$(CONFIG_MACH_CCMX51)			:= ccxmx51
 
 machdirs := $(patsubst %,arch/arm/mach-%/,$(machine-y))
 
diff --git a/arch/arm/boards/ccxmx51/Makefile b/arch/arm/boards/ccxmx51/Makefile
new file mode 100644
index 0000000000..249927ef2e
--- /dev/null
+++ b/arch/arm/boards/ccxmx51/Makefile
@@ -0,0 +1,2 @@
+obj-y					+= flash_header.o ccxmx51.o
+obj-$(CONFIG_MACH_CCMX51_BASEBOARD)	+= ccxmx51js.o
diff --git a/arch/arm/boards/ccxmx51/ccxmx51.c b/arch/arm/boards/ccxmx51/ccxmx51.c
new file mode 100644
index 0000000000..f494174b18
--- /dev/null
+++ b/arch/arm/boards/ccxmx51/ccxmx51.c
@@ -0,0 +1,489 @@
+/*
+ * (C) Copyright 2009-2010 Digi International, Inc.
+ * Copyright (C) 2007 Sascha Hauer, Pengutronix
+ * (c) 2011 Eukrea Electromatique, Eric Bénard <eric@eukrea.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <net.h>
+#include <init.h>
+#include <environment.h>
+#include <mach/imx-regs.h>
+#include <fec.h>
+#include <mach/gpio.h>
+#include <asm/armlinux.h>
+#include <generated/mach-types.h>
+#include <partition.h>
+#include <fs.h>
+#include <fcntl.h>
+#include <sizes.h>
+#include <nand.h>
+#include <notifier.h>
+#include <spi/spi.h>
+#include <mfd/mc13xxx.h>
+#include <asm/io.h>
+#include <mach/imx-nand.h>
+#include <mach/spi.h>
+#include <mach/generic.h>
+#include <mach/iomux-mx51.h>
+#include <mach/devices-imx51.h>
+#include <mach/iim.h>
+#include <mach/clock-imx51_53.h>
+#include <mach/imx5.h>
+
+#include "ccxmx51.h"
+
+static struct ccxmx51_ident ccxmx51_ids[] = {
+/* 0x00 */	{ "Unknown",						0,       0, 0, 0, 0 },
+/* 0x01 */	{ "Not supported",					0,       0, 0, 0, 0 },
+/* 0x02 */	{ "i.MX515@800MHz, Wireless, PHY, Ext. Eth, Accel",	SZ_512M, 0, 1, 1, 1 },
+/* 0x03 */	{ "i.MX515@800MHz, PHY, Ext. Eth, Accel",		SZ_512M, 0, 1, 1, 0 },
+/* 0x04 */	{ "i.MX515@600MHz, Wireless, PHY, Ext. Eth, Accel",	SZ_512M, 1, 1, 1, 1 },
+/* 0x05 */	{ "i.MX515@600MHz, PHY, Ext. Eth, Accel",		SZ_512M, 1, 1, 1, 0 },
+/* 0x06 */	{ "i.MX515@800MHz, Wireless, PHY, Accel",		SZ_512M, 0, 1, 0, 1 },
+/* 0x07 */	{ "i.MX515@800MHz, PHY, Accel",				SZ_512M, 0, 1, 0, 0 },
+/* 0x08 */	{ "i.MX515@800MHz, Wireless, PHY, Accel",		SZ_256M, 0, 1, 0, 1 },
+/* 0x09 */	{ "i.MX515@800MHz, PHY, Accel",				SZ_256M, 0, 1, 0, 0 },
+/* 0x0a */	{ "i.MX515@600MHz, Wireless, PHY, Accel",		SZ_256M, 1, 1, 0, 1 },
+/* 0x0b */	{ "i.MX515@600MHz, PHY, Accel",				SZ_256M, 1, 1, 0, 0 },
+/* 0x0c */	{ "i.MX515@800MHz, Wireless, PHY, Accel",		SZ_128M, 0, 1, 0, 1 },
+/* 0x0d */	{ "i.MX512@800MHz",					SZ_128M, 0, 0, 0, 0 },
+/* 0x0e */	{ "i.MX515@800MHz, Wireless, PHY, Accel",		SZ_512M, 0, 1, 0, 1 },
+/* 0x0f */	{ "i.MX515@600MHz, PHY, Accel",				SZ_128M, 1, 1, 0, 0 },
+/* 0x10 */	{ "i.MX515@600MHz, Wireless, PHY, Accel",		SZ_128M, 1, 1, 0, 1 },
+/* 0x11 */	{ "i.MX515@800MHz, PHY, Accel",				SZ_128M, 0, 1, 0, 0 },
+/* 0x12 */	{ "i.MX515@600MHz, Wireless, PHY, Accel",		SZ_512M, 1, 1, 0, 1 },
+/* 0x13 */	{ "i.MX515@800MHz, PHY, Accel",				SZ_512M, 0, 1, 0, 0 },
+};
+
+struct ccxmx51_ident *ccxmx51_id;
+
+struct imx_nand_platform_data nand_info = {
+	.width		= 1,
+	.hw_ecc		= 1,
+	.flash_bbt	= 1,
+};
+
+#ifdef CONFIG_DRIVER_NET_FEC_IMX
+static struct fec_platform_data fec_info = {
+	.xcv_type	= MII100,
+	.phy_addr	= 7,
+};
+#endif
+
+static iomux_v3_cfg_t ccxmx51_pads[] = {
+	/* UART1 */
+	MX51_PAD_UART1_RXD__UART1_RXD,
+	MX51_PAD_UART1_TXD__UART1_TXD,
+	/* UART2 */
+	MX51_PAD_UART2_RXD__UART2_RXD,
+	MX51_PAD_UART2_TXD__UART2_TXD,
+	/* UART3 */
+	MX51_PAD_UART3_RXD__UART3_RXD,
+	MX51_PAD_UART3_TXD__UART3_TXD,
+	/* I2C2 */
+	MX51_PAD_GPIO1_2__I2C2_SCL,
+	MX51_PAD_GPIO1_3__I2C2_SDA,
+	/* eCSPI1 */
+	MX51_PAD_CSPI1_MOSI__ECSPI1_MOSI,
+	MX51_PAD_CSPI1_MISO__ECSPI1_MISO,
+	MX51_PAD_CSPI1_SCLK__ECSPI1_SCLK,
+	MX51_PAD_CSPI1_RDY__ECSPI1_RDY,
+	MX51_PAD_CSPI1_SS0__ECSPI1_SS0,
+	MX51_PAD_CSPI1_SS1__ECSPI1_SS1,
+	/* FEC */
+	MX51_PAD_DISP2_DAT14__FEC_RDATA0,
+	MX51_PAD_DI2_DISP_CLK__FEC_RDATA1,
+	MX51_PAD_DI_GP4__FEC_RDATA2,
+	MX51_PAD_DISP2_DAT0__FEC_RDATA3,
+	MX51_PAD_DISP2_DAT15__FEC_TDATA0,
+	MX51_PAD_DISP2_DAT6__FEC_TDATA1,
+	MX51_PAD_DISP2_DAT7__FEC_TDATA2,
+	MX51_PAD_DISP2_DAT8__FEC_TDATA3,
+	MX51_PAD_DISP2_DAT9__FEC_TX_EN,
+	MX51_PAD_DISP2_DAT10__FEC_COL,
+	MX51_PAD_DISP2_DAT11__FEC_RX_CLK,
+	MX51_PAD_DISP2_DAT12__FEC_RX_DV,
+	MX51_PAD_DISP2_DAT13__FEC_TX_CLK,
+	MX51_PAD_DI2_PIN2__FEC_MDC,
+	MX51_PAD_DI2_PIN4__FEC_CRS,
+	MX51_PAD_DI2_PIN3__FEC_MDIO,
+	MX51_PAD_DI_GP3__FEC_TX_ER,
+	MX51_PAD_DISP2_DAT1__FEC_RX_ER,
+	/* WEIM */
+	MX51_PAD_EIM_DA0__EIM_DA0,
+	MX51_PAD_EIM_DA1__EIM_DA1,
+	MX51_PAD_EIM_DA2__EIM_DA2,
+	MX51_PAD_EIM_DA3__EIM_DA3,
+	MX51_PAD_EIM_DA4__EIM_DA4,
+	MX51_PAD_EIM_DA5__EIM_DA5,
+	MX51_PAD_EIM_DA6__EIM_DA6,
+	MX51_PAD_EIM_DA7__EIM_DA7,
+	MX51_PAD_EIM_D16__EIM_D16,
+	MX51_PAD_EIM_D17__EIM_D17,
+	MX51_PAD_EIM_D18__EIM_D18,
+	MX51_PAD_EIM_D19__EIM_D19,
+	MX51_PAD_EIM_D20__EIM_D20,
+	MX51_PAD_EIM_D21__EIM_D21,
+	MX51_PAD_EIM_D22__EIM_D22,
+	MX51_PAD_EIM_D23__EIM_D23,
+	MX51_PAD_EIM_D24__EIM_D24,
+	MX51_PAD_EIM_D25__EIM_D25,
+	MX51_PAD_EIM_D26__EIM_D26,
+	MX51_PAD_EIM_D27__EIM_D27,
+	MX51_PAD_EIM_D28__EIM_D28,
+	MX51_PAD_EIM_D29__EIM_D29,
+	MX51_PAD_EIM_D30__EIM_D30,
+	MX51_PAD_EIM_D31__EIM_D31,
+	MX51_PAD_EIM_OE__EIM_OE,
+	MX51_PAD_EIM_CS5__EIM_CS5,
+	/* NAND */
+	MX51_PAD_NANDF_D0__NANDF_D0,
+	MX51_PAD_NANDF_D1__NANDF_D1,
+	MX51_PAD_NANDF_D2__NANDF_D2,
+	MX51_PAD_NANDF_D3__NANDF_D3,
+	MX51_PAD_NANDF_D4__NANDF_D4,
+	MX51_PAD_NANDF_D5__NANDF_D5,
+	MX51_PAD_NANDF_D6__NANDF_D6,
+	MX51_PAD_NANDF_D7__NANDF_D7,
+	MX51_PAD_NANDF_ALE__NANDF_ALE,
+	MX51_PAD_NANDF_CLE__NANDF_CLE,
+	MX51_PAD_NANDF_RE_B__NANDF_RE_B,
+	MX51_PAD_NANDF_WE_B__NANDF_WE_B,
+	MX51_PAD_NANDF_WP_B__NANDF_WP_B,
+	MX51_PAD_NANDF_CS0__NANDF_CS0,
+	MX51_PAD_NANDF_RB0__NANDF_RB0,
+	/* LAN9221 IRQ (GPIO1.9) */
+	MX51_PAD_GPIO1_9__GPIO1_9,
+	/* MC13892 IRQ (GPIO1.5) */
+	MX51_PAD_GPIO1_5__GPIO1_5,
+	/* MMA7455LR IRQ1 (GPIO1.7) */
+	MX51_PAD_GPIO1_7__GPIO1_7,
+	/* MMA7455LR IRQ2 (GPIO1.6) */
+	MX51_PAD_GPIO1_6__GPIO1_6,
+};
+
+#define CCXMX51_ECSPI1_CS0	IMX_GPIO_NR(4, 24)
+#define CCXMX51_ECSPI1_CS1	IMX_GPIO_NR(4, 25)
+
+static int ecspi_0_cs[] = { CCXMX51_ECSPI1_CS0, CCXMX51_ECSPI1_CS1, };
+
+static struct spi_imx_master ecspi_0_data = {
+	.chipselect	= ecspi_0_cs,
+	.num_chipselect	= ARRAY_SIZE(ecspi_0_cs),
+};
+
+static const struct spi_board_info ccxmx51_spi_board_info[] = {
+	{
+		.name		= "mc13xxx-spi",
+		.max_speed_hz	= 6000000,
+		.bus_num	= 0,
+		.chip_select	= 0,
+	},
+};
+
+static int ccxmx51_mem_init(void)
+{
+	/* Add minimal SDRAM first */
+	arm_add_mem_device("ram0", MX51_CSD0_BASE_ADDR, SZ_128M);
+
+	return 0;
+}
+mem_initcall(ccxmx51_mem_init);
+
+static void ccxmx51_otghost_init(void)
+{
+#define MX51_USBOTHER_REGS_OFFSET		0x800
+#define MX51_USBCTRL_OFFSET			0x0
+#define MX51_USB_PHY_CTR_FUNC_OFFSET		0x8
+#define MX51_USB_PHY_CTR_FUNC2_OFFSET		0xc
+#define MX51_USB_UTMI_PHYCTRL1_PLLDIV_MASK	0x3
+#define MX51_USB_PLL_DIV_19_2_MHZ		0x00
+#define MX51_USB_PLL_DIV_24_MHZ			0x01
+#define MX51_USB_PLL_DIV_26_MHZ			0x02
+#define MX51_USB_PLL_DIV_27_MHZ			0x03
+#define MX51_OTG_PHYCTRL_OC_DIS_BIT		(1 << 8)
+#define MX51_OTG_UCTRL_OWIE_BIT			(1 << 27)
+#define MX51_OTG_UCTRL_OPM_BIT			(1 << 24)
+
+#define USBOTHER_BASE				(MX51_OTG_BASE_ADDR + MX51_USBOTHER_REGS_OFFSET)
+
+	u32 reg;
+
+	/* Set sysclock to 24 MHz */
+	reg = readl(USBOTHER_BASE + MX51_USB_PHY_CTR_FUNC2_OFFSET);
+	reg &= ~MX51_USB_UTMI_PHYCTRL1_PLLDIV_MASK;
+	reg |= MX51_USB_PLL_DIV_24_MHZ;
+	writel(reg, USBOTHER_BASE + MX51_USB_PHY_CTR_FUNC2_OFFSET);
+
+	/* OC is not used */
+	reg = readl(USBOTHER_BASE + MX51_USB_PHY_CTR_FUNC_OFFSET);
+	reg |= MX51_OTG_PHYCTRL_OC_DIS_BIT;
+	writel(reg, USBOTHER_BASE + MX51_USB_PHY_CTR_FUNC_OFFSET);
+
+	/* Power pins enable */
+	reg = readl(USBOTHER_BASE + MX51_USBCTRL_OFFSET);
+	reg |= MX51_OTG_UCTRL_OWIE_BIT | MX51_OTG_UCTRL_OPM_BIT;
+	writel(reg, USBOTHER_BASE + MX51_USBCTRL_OFFSET);
+
+	/* Setup PORTSC */
+	reg = readl(MX51_OTG_BASE_ADDR + 0x184);
+	reg &= ~(3 << 30);
+	reg |= 1 << 28;
+	writel(reg, MX51_OTG_BASE_ADDR + 0x184);
+
+	mdelay(10);
+
+	add_generic_usb_ehci_device(0, MX51_OTG_BASE_ADDR, NULL);
+}
+
+static int ccxmx51_power_init(void)
+{
+	struct mc13xxx *mc13xxx_dev;
+	u32 val;
+
+	mc13xxx_dev = mc13xxx_get();
+	if (!mc13xxx_dev)
+		return -ENODEV;
+
+	mc13xxx_reg_read(mc13xxx_dev, MC13892_REG_POWER_MISC, &val);
+	/* Reset devices by clearing GP01-GPO4 */
+	val &= ~((1 << 21) | (3 << 12) | (3 << 10) | (3 << 8) | (3 << 6));
+	/* Switching off the PWGT1SPIEN */
+	val |= (1 << 15);
+	/* Switching on the PWGT2SPIEN */
+	val &= ~(1 << 16);
+	/* Enable short circuit protection */
+	val |= (1 << 0);
+	mc13xxx_reg_write(mc13xxx_dev, MC13892_REG_POWER_MISC, val);
+
+	/* Allow charger to charge (4.2V and 560mA) */
+	val = 0x238033;
+	mc13xxx_reg_write(mc13xxx_dev, MC13892_REG_CHARGE, val);
+
+	/* Set core voltage (SW1) to 1.1V */
+	mc13xxx_reg_read(mc13xxx_dev, MC13892_REG_SW_0, &val);
+	val &= ~0x00001f;
+	val |=  0x000014;
+	mc13xxx_reg_write(mc13xxx_dev, MC13892_REG_SW_0, val);
+
+	if (imx_silicon_revision() < IMX_CHIP_REV_3_0) {
+		/* Setup VCC (SW2) to 1.25 */
+		mc13xxx_reg_read(mc13xxx_dev, MC13892_REG_SW_1, &val);
+		val &= ~0x00001f;
+		val |=  0x00001a;
+		mc13xxx_reg_write(mc13xxx_dev, MC13892_REG_SW_1, val);
+
+		/* Setup 1V2_DIG1 (SW3) to 1.25 */
+		mc13xxx_reg_read(mc13xxx_dev, MC13892_REG_SW_2, &val);
+		val &= ~0x00001f;
+		val |=  0x00001a;
+		mc13xxx_reg_write(mc13xxx_dev, MC13892_REG_SW_2, val);
+	} else {
+		/* Setup VCC (SW2) to 1.225 */
+		mc13xxx_reg_read(mc13xxx_dev, MC13892_REG_SW_1, &val);
+		val &= ~0x00001f;
+		val |=  0x000019;
+		mc13xxx_reg_write(mc13xxx_dev, MC13892_REG_SW_1, val);
+
+		/* Setup 1V2_DIG1 (SW3) to 1.2 */
+		mc13xxx_reg_read(mc13xxx_dev, MC13892_REG_SW_2, &val);
+		val &= ~0x00001f;
+		val |=  0x000018;
+		mc13xxx_reg_write(mc13xxx_dev, MC13892_REG_SW_2, val);
+	}
+
+	if (mc13xxx_dev->revision <= MC13892_REVISION_2_0) {
+		/* Set switchers in PWM mode for Atlas 2.0 and lower */
+		/* Setup the switcher mode for SW1 & SW2*/
+		mc13xxx_reg_read(mc13xxx_dev, MC13892_REG_SW_4, &val);
+		val &= ~0x003c0f;
+		val |=  0x001405;
+		mc13xxx_reg_write(mc13xxx_dev, MC13892_REG_SW_4, val);
+
+		/* Setup the switcher mode for SW3 & SW4 */
+		mc13xxx_reg_read(mc13xxx_dev, MC13892_REG_SW_5, &val);
+		val &= ~0x000f0f;
+		val |=  0x000505;
+		mc13xxx_reg_write(mc13xxx_dev, MC13892_REG_SW_5, val);
+	} else {
+		/* Set switchers in Auto in NORMAL mode & STANDBY mode for Atlas 2.0a */
+		/* Setup the switcher mode for SW1 & SW2*/
+		mc13xxx_reg_read(mc13xxx_dev, MC13892_REG_SW_4, &val);
+		val &= ~0x003c0f;
+		val |=  0x002008;
+		mc13xxx_reg_write(mc13xxx_dev, MC13892_REG_SW_4, val);
+
+		/* Setup the switcher mode for SW3 & SW4 */
+		mc13xxx_reg_read(mc13xxx_dev, MC13892_REG_SW_5, &val);
+		val &= ~0x000f0f;
+		val |=  0x000808;
+		mc13xxx_reg_write(mc13xxx_dev, MC13892_REG_SW_5, val);
+	}
+
+	/* Set VVIDEO to 2.775V, VAUDIO to 3V, VSD to 3.15V */
+	mc13xxx_reg_read(mc13xxx_dev, MC13892_REG_SETTING_1, &val);
+	val &= ~0x0001fc;
+	val |=  0x0001f4;
+	mc13xxx_reg_write(mc13xxx_dev, MC13892_REG_SETTING_1, val);
+
+	/* Configure VGEN3 and VCAM regulators to use external PNP */
+	val = 0x000208;
+	mc13xxx_reg_write(mc13xxx_dev, MC13892_REG_MODE_1, val);
+	udelay(200);
+
+	/* Set VGEN3 to 1.8V */
+	mc13xxx_reg_read(mc13xxx_dev, MC13892_REG_SETTING_0, &val);
+	val &= ~(1 << 14);
+	mc13xxx_reg_write(mc13xxx_dev, MC13892_REG_SETTING_0, val);
+
+	/* Enable VGEN3, VCAM, VAUDIO, VVIDEO, VSD regulators */
+	val = 0x049249;
+	mc13xxx_reg_write(mc13xxx_dev, MC13892_REG_MODE_1, val);
+
+	/* Enable USB1 charger */
+	val = 0x000409;
+	mc13xxx_reg_write(mc13xxx_dev, MC13892_REG_USB1, val);
+
+	/* Set VCOIN to 3.0V and Enable It */
+	mc13xxx_reg_read(mc13xxx_dev, MC13892_REG_POWER_CTL0, &val);
+	val &= ~(7 << 20);
+	val |= (4 << 20) | (1 << 23);
+	mc13xxx_reg_write(mc13xxx_dev, MC13892_REG_POWER_CTL0, val);
+	/* Keeps VSRTC and CLK32KMCU */
+	val |= (1 << 4);
+	mc13xxx_reg_write(mc13xxx_dev, MC13892_REG_POWER_CTL0, val);
+
+	/* De-assert reset of external devices on GP01, GPO2, GPO3 and GPO4 */
+	mc13xxx_reg_read(mc13xxx_dev, MC13892_REG_POWER_MISC, &val);
+	/* GPO1 - External */
+	/* GP02 - LAN9221  */
+	/* GP03 - FEC      */
+	/* GP04 - Wireless */
+	if (IS_ENABLED(CONFIG_DRIVER_NET_SMC911X) && ccxmx51_id->eth0)
+		val |= (1 << 8);
+	if (IS_ENABLED(CONFIG_DRIVER_NET_FEC_IMX) && ccxmx51_id->eth1)
+		val |= (1 << 10);
+	if (ccxmx51_id->wless)
+		val |= (1 << 12);
+	mc13xxx_reg_write(mc13xxx_dev, MC13892_REG_POWER_MISC, val);
+
+	udelay(100);
+
+	return 0;
+}
+
+static int ccxmx51_devices_init(void)
+{
+	u8 hwid[6];
+	int pwr;
+	char manloc;
+
+	if ((imx_iim_read(1, 9, hwid, sizeof(hwid)) != sizeof(hwid)) || (hwid[0] < 0x02) || (hwid[0] >= ARRAY_SIZE(ccxmx51_ids)))
+		memset(hwid, 0x00, sizeof(hwid));
+
+	ccxmx51_id = &ccxmx51_ids[hwid[0]];
+	printf("Module Variant: %s (0x%02x)\n", ccxmx51_id->id_string, hwid[0]);
+
+	if (hwid[0]) {
+		printf("Module HW Rev : %02x\n", hwid[1]);
+		switch (hwid[2] & 0xc0) {
+		case 0x00:
+			manloc = 'B';
+			break;
+		case 0x40:
+			manloc = 'W';
+			break;
+		case 0x80:
+			manloc = 'S';
+			break;
+		default:
+			manloc = 'N';
+			break;
+		}
+		printf("Module Serial : %c%d\n", manloc, ((hwid[2] & 0x3f) << 24) | (hwid[3] << 16) | (hwid[4] << 8) | hwid[5]);
+		if ((ccxmx51_id->mem_sz - SZ_128M) > 0)
+			arm_add_mem_device("ram1", MX51_CSD0_BASE_ADDR + SZ_128M, ccxmx51_id->mem_sz - SZ_128M);
+	}
+
+	imx51_add_uart1();
+	imx51_add_uart2();
+
+	spi_register_board_info(ccxmx51_spi_board_info, ARRAY_SIZE(ccxmx51_spi_board_info));
+	imx51_add_spi0(&ecspi_0_data);
+
+	pwr = ccxmx51_power_init();
+	console_flush();
+	imx51_init_lowlevel((ccxmx51_id->industrial || pwr) ? 600 : 800);
+	clock_notifier_call_chain();
+	if (pwr)
+		printf("Could not setup PMIC. Clocks not adjusted.\n");
+
+	imx51_add_i2c1(NULL);
+
+	imx51_add_nand(&nand_info);
+	devfs_add_partition("nand0", 0x00000, 0x80000, DEVFS_PARTITION_FIXED, "self_raw");
+	dev_add_bb_dev("self_raw", "self0");
+	devfs_add_partition("nand0", 0x80000, 0x40000, DEVFS_PARTITION_FIXED, "env_raw");
+	dev_add_bb_dev("env_raw", "env0");
+
+#ifdef CONFIG_DRIVER_NET_FEC_IMX
+	if (ccxmx51_id->eth0 && !pwr) {
+		imx51_add_fec(&fec_info);
+		eth_register_ethaddr(0, hwid);
+	}
+#endif
+
+#ifdef CONFIG_DRIVER_NET_SMC911X
+	if (ccxmx51_id->eth1 && !pwr) {
+		/* Configure the WEIM CS5 timming, bus width, etc */
+		/* 16 bit on DATA[31..16], not multiplexed, async */
+		writel(0x00420081, MX51_WEIM_BASE_ADDR + WEIM_CSxGCR1(5));
+		/* ADH has not effect on non muxed bus */
+		writel(0, MX51_WEIM_BASE_ADDR + WEIM_CSxGCR2(5));
+		/* RWSC=50, RADVA=2, RADVN=6, OEA=0, OEN=0, RCSA=0, RCSN=0 */
+		writel(0x32260000, MX51_WEIM_BASE_ADDR + WEIM_CSxRCR1(5));
+		/* APR=0 */
+		writel(0, MX51_WEIM_BASE_ADDR + WEIM_CSxRCR2(5));
+		/* WAL=0, WBED=1, WWSC=50, WADVA=2, WADVN=6, WEA=0, WEN=0, WCSA=0 */
+		writel(0x72080f00, MX51_WEIM_BASE_ADDR + WEIM_CSxWCR1(5));
+
+		/* LAN9221 network controller */
+		add_generic_device("smc911x", 1, NULL, MX51_CS5_BASE_ADDR, SZ_4K, IORESOURCE_MEM, NULL);
+	}
+#endif
+
+	ccxmx51_otghost_init();
+
+	armlinux_set_bootparams((void *)(MX51_CSD0_BASE_ADDR + 0x100));
+
+	armlinux_set_architecture(ccxmx51_id->wless ? MACH_TYPE_CCWMX51 : MACH_TYPE_CCMX51);
+
+	return 0;
+}
+device_initcall(ccxmx51_devices_init);
+
+static int ccxmx51_console_init(void)
+{
+	mxc_iomux_v3_setup_multiple_pads(ccxmx51_pads, ARRAY_SIZE(ccxmx51_pads));
+
+	imx51_add_uart0();
+
+	return 0;
+}
+console_initcall(ccxmx51_console_init);
diff --git a/arch/arm/boards/ccxmx51/ccxmx51.dox b/arch/arm/boards/ccxmx51/ccxmx51.dox
new file mode 100644
index 0000000000..cc28e8d66a
--- /dev/null
+++ b/arch/arm/boards/ccxmx51/ccxmx51.dox
@@ -0,0 +1,7 @@
+/** @page ccxmx51 Digi ConnectCore board
+
+This boards is based on a Freescale i.MX51 CPU. The board is shipped with:
+- Up to 8 GB NAND Flash.
+- Up to 512 MB DDR2 RAM.
+
+*/
diff --git a/arch/arm/boards/ccxmx51/ccxmx51.h b/arch/arm/boards/ccxmx51/ccxmx51.h
new file mode 100644
index 0000000000..3feacac034
--- /dev/null
+++ b/arch/arm/boards/ccxmx51/ccxmx51.h
@@ -0,0 +1,35 @@
+/*
+ * Copyright 2010 Digi International Inc. All Rights Reserved.
+ */
+
+/*
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#ifndef _CCXMX51_H_
+#define _CCXMX51_H_
+
+struct ccxmx51_hwid {
+	u8		variant;
+	u8		version;
+	u32		sn;
+	char		mloc;
+};
+
+struct ccxmx51_ident {
+	const char	*id_string;
+	const int	mem_sz;
+	const char	industrial;
+	const char	eth0;
+	const char	eth1;
+	const char	wless;
+};
+
+extern struct ccxmx51_ident *ccxmx51_id;
+
+#endif	/* _CCXMX51_H_ */
diff --git a/arch/arm/boards/ccxmx51/ccxmx51js.c b/arch/arm/boards/ccxmx51/ccxmx51js.c
new file mode 100644
index 0000000000..f04615d888
--- /dev/null
+++ b/arch/arm/boards/ccxmx51/ccxmx51js.c
@@ -0,0 +1,90 @@
+/*
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <io.h>
+#include <init.h>
+#include <mci.h>
+#include <asm/armlinux.h>
+#include <mach/imx-regs.h>
+#include <mach/iomux-mx51.h>
+#include <mach/devices-imx51.h>
+#include <generated/mach-types.h>
+
+#include "ccxmx51.h"
+
+static iomux_v3_cfg_t ccxmx51js_pads[] = {
+	/* SD1 */
+	MX51_PAD_SD1_CLK__SD1_CLK,
+	MX51_PAD_SD1_CMD__SD1_CMD,
+	MX51_PAD_SD1_DATA0__SD1_DATA0,
+	MX51_PAD_SD1_DATA1__SD1_DATA1,
+	MX51_PAD_SD1_DATA2__SD1_DATA2,
+	MX51_PAD_SD1_DATA3__SD1_DATA3,
+	/* SD3 */
+	MX51_PAD_NANDF_CS7__SD3_CLK,
+	MX51_PAD_NANDF_RDY_INT__SD3_CMD,
+	MX51_PAD_NANDF_D8__SD3_DATA0,
+	MX51_PAD_NANDF_D9__SD3_DATA1,
+	MX51_PAD_NANDF_D10__SD3_DATA2,
+	MX51_PAD_NANDF_D11__SD3_DATA3,
+	MX51_PAD_NANDF_D12__SD3_DAT4,
+	MX51_PAD_NANDF_D13__SD3_DAT5,
+	MX51_PAD_NANDF_D14__SD3_DAT6,
+	MX51_PAD_NANDF_D15__SD3_DAT7,
+	/* USB HOST1 */
+	MX51_PAD_USBH1_CLK__USBH1_CLK,
+	MX51_PAD_USBH1_DIR__USBH1_DIR,
+	MX51_PAD_USBH1_NXT__USBH1_NXT,
+	MX51_PAD_USBH1_STP__USBH1_STP,
+	MX51_PAD_USBH1_DATA0__USBH1_DATA0,
+	MX51_PAD_USBH1_DATA1__USBH1_DATA1,
+	MX51_PAD_USBH1_DATA2__USBH1_DATA2,
+	MX51_PAD_USBH1_DATA3__USBH1_DATA3,
+	MX51_PAD_USBH1_DATA4__USBH1_DATA4,
+	MX51_PAD_USBH1_DATA5__USBH1_DATA5,
+	MX51_PAD_USBH1_DATA6__USBH1_DATA6,
+	MX51_PAD_USBH1_DATA7__USBH1_DATA7,
+};
+
+static struct esdhc_platform_data sdhc1_pdata = {
+	.cd_type	= ESDHC_CD_NONE,
+	.wp_type	= ESDHC_WP_NONE,
+	.caps		= MMC_MODE_4BIT,
+};
+
+static struct esdhc_platform_data sdhc3_pdata = {
+	.cd_type	= ESDHC_CD_NONE,
+	.wp_type	= ESDHC_WP_NONE,
+	.caps		= MMC_MODE_4BIT | MMC_MODE_8BIT,
+};
+
+static int ccxmx51js_init(void)
+{
+	mxc_iomux_v3_setup_multiple_pads(ccxmx51js_pads, ARRAY_SIZE(ccxmx51js_pads));
+
+	if (IS_ENABLED(CONFIG_MCI_IMX_ESDHC)) {
+		imx51_add_mmc0(&sdhc1_pdata);
+		imx51_add_mmc2(&sdhc3_pdata);
+	}
+
+	armlinux_set_architecture(ccxmx51_id->wless ? MACH_TYPE_CCWMX51JS : MACH_TYPE_CCMX51JS);
+
+	return 0;
+}
+
+late_initcall(ccxmx51js_init);
diff --git a/arch/arm/boards/ccxmx51/config.h b/arch/arm/boards/ccxmx51/config.h
new file mode 100644
index 0000000000..fdf2f819a1
--- /dev/null
+++ b/arch/arm/boards/ccxmx51/config.h
@@ -0,0 +1,24 @@
+/**
+ * @file
+ * @brief Global defintions for the ARM i.MX51 based ccmx51 board
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#endif	/* __CONFIG_H */
diff --git a/arch/arm/boards/ccxmx51/env/config b/arch/arm/boards/ccxmx51/env/config
new file mode 100644
index 0000000000..bbd43e712e
--- /dev/null
+++ b/arch/arm/boards/ccxmx51/env/config
@@ -0,0 +1,37 @@
+#!/bin/sh
+
+machine=ccmx51
+
+# use 'dhcp' to do dhcp in barebox and in kernel
+# use 'none' if you want to skip kernel ip autoconfiguration
+ip=none
+
+# or set your networking parameters here
+#eth0.ipaddr=a.b.c.d
+#eth0.netmask=a.b.c.d
+#eth0.gateway=a.b.c.d
+#eth0.serverip=a.b.c.d
+
+# can be either 'nfs', 'tftp' or 'nand'
+kernel_loc=nand
+# can be either 'net', 'nand' or 'initrd'
+rootfs_loc=nand
+
+# rootfs
+rootfs_type=cramfs
+
+# kernel
+kernelimage_type=zimage
+kernel_img=/dev/nand0.kernel
+
+autoboot_timeout=3
+
+bootargs="console=ttymxc0,115200"
+
+device_type="nand"
+nand_device="mxc_nand"
+nand_parts="512k(barebox)ro,256k(bareboxenv),3328k(kernel),-(root)"
+rootfs_mtdblock_nand=3
+
+# set a fancy prompt (if support is compiled in)
+PS1="\e[1;32mbarebox@\e[1;31m\h:\w\e[0m "
diff --git a/arch/arm/boards/ccxmx51/flash_header.c b/arch/arm/boards/ccxmx51/flash_header.c
new file mode 100644
index 0000000000..c148eea4ff
--- /dev/null
+++ b/arch/arm/boards/ccxmx51/flash_header.c
@@ -0,0 +1,84 @@
+#include <common.h>
+#include <mach/imx-flash-header.h>
+#include <asm/barebox-arm-head.h>
+
+void __naked __flash_header_start go(void)
+{
+	barebox_arm_head();
+}
+
+struct imx_dcd_entry __dcd_entry_section dcd_entry[] = {
+	{ .ptr_type = 4, .addr = 0x73fa88a0, .val = 0x00000200, },
+	{ .ptr_type = 4, .addr = 0x73fa850c, .val = 0x000020c5, },
+	{ .ptr_type = 4, .addr = 0x73fa8510, .val = 0x000020c5, },
+	{ .ptr_type = 4, .addr = 0x73fa883c, .val = 0x00000002, },
+	{ .ptr_type = 4, .addr = 0x73fa8848, .val = 0x00000002, },
+	{ .ptr_type = 4, .addr = 0x73fa84b8, .val = 0x000000e7, },
+	{ .ptr_type = 4, .addr = 0x73fa84bc, .val = 0x00000045, },
+	{ .ptr_type = 4, .addr = 0x73fa84c0, .val = 0x00000045, },
+	{ .ptr_type = 4, .addr = 0x73fa84c4, .val = 0x00000045, },
+	{ .ptr_type = 4, .addr = 0x73fa84c8, .val = 0x00000045, },
+	{ .ptr_type = 4, .addr = 0x73fa8820, .val = 0x00000000, },
+	{ .ptr_type = 4, .addr = 0x73fa84a4, .val = 0x00000003, },
+	{ .ptr_type = 4, .addr = 0x73fa84a8, .val = 0x00000003, },
+	{ .ptr_type = 4, .addr = 0x73fa84ac, .val = 0x000000e3, },
+	{ .ptr_type = 4, .addr = 0x73fa84b0, .val = 0x000000e3, },
+	{ .ptr_type = 4, .addr = 0x73fa84b4, .val = 0x000000e3, },
+	{ .ptr_type = 4, .addr = 0x73fa84cc, .val = 0x000000e3, },
+	{ .ptr_type = 4, .addr = 0x73fa84d0, .val = 0x000000e2, },
+	{ .ptr_type = 4, .addr = 0x73fa882c, .val = 0x00000004, },
+	{ .ptr_type = 4, .addr = 0x73fa88a4, .val = 0x00000004, },
+	{ .ptr_type = 4, .addr = 0x73fa88ac, .val = 0x00000004, },
+	{ .ptr_type = 4, .addr = 0x73fa88b8, .val = 0x00000004, },
+	{ .ptr_type = 4, .addr = 0x83fd9000, .val = 0x82a20000, },
+	{ .ptr_type = 4, .addr = 0x83fd9008, .val = 0x82a20000, },
+	{ .ptr_type = 4, .addr = 0x83fd9010, .val = 0x000ad0d0, },
+	{ .ptr_type = 4, .addr = 0x83fd9004, .val = 0x3f3584ab, },
+	{ .ptr_type = 4, .addr = 0x83fd900c, .val = 0x3f3584ab, },
+	{ .ptr_type = 4, .addr = 0x83fd9014, .val = 0x04008008, },
+	{ .ptr_type = 4, .addr = 0x83fd9014, .val = 0x0000801a, },
+	{ .ptr_type = 4, .addr = 0x83fd9014, .val = 0x0000801b, },
+	{ .ptr_type = 4, .addr = 0x83fd9014, .val = 0x00448019, },
+	{ .ptr_type = 4, .addr = 0x83fd9014, .val = 0x07328018, },
+	{ .ptr_type = 4, .addr = 0x83fd9014, .val = 0x04008008, },
+	{ .ptr_type = 4, .addr = 0x83fd9014, .val = 0x00008010, },
+	{ .ptr_type = 4, .addr = 0x83fd9014, .val = 0x00008010, },
+	{ .ptr_type = 4, .addr = 0x83fd9014, .val = 0x06328018, },
+	{ .ptr_type = 4, .addr = 0x83fd9014, .val = 0x03808019, },
+	{ .ptr_type = 4, .addr = 0x83fd9014, .val = 0x00408019, },
+	{ .ptr_type = 4, .addr = 0x83fd9014, .val = 0x00008000, },
+	{ .ptr_type = 4, .addr = 0x83fd9014, .val = 0x0400800c, },
+	{ .ptr_type = 4, .addr = 0x83fd9014, .val = 0x0000801e, },
+	{ .ptr_type = 4, .addr = 0x83fd9014, .val = 0x0000801f, },
+	{ .ptr_type = 4, .addr = 0x83fd9014, .val = 0x0000801d, },
+	{ .ptr_type = 4, .addr = 0x83fd9014, .val = 0x0732801c, },
+	{ .ptr_type = 4, .addr = 0x83fd9014, .val = 0x0400800c, },
+	{ .ptr_type = 4, .addr = 0x83fd9014, .val = 0x00008014, },
+	{ .ptr_type = 4, .addr = 0x83fd9014, .val = 0x00008014, },
+	{ .ptr_type = 4, .addr = 0x83fd9014, .val = 0x0632801c, },
+	{ .ptr_type = 4, .addr = 0x83fd9014, .val = 0x0380801d, },
+	{ .ptr_type = 4, .addr = 0x83fd9014, .val = 0x0040801d, },
+	{ .ptr_type = 4, .addr = 0x83fd9014, .val = 0x00008004, },
+	{ .ptr_type = 4, .addr = 0x83fd9000, .val = 0xb2a20000, },
+	{ .ptr_type = 4, .addr = 0x83fd9008, .val = 0xb2a20000, },
+	{ .ptr_type = 4, .addr = 0x83fd9010, .val = 0x000ad6d0, },
+	{ .ptr_type = 4, .addr = 0x83fd9034, .val = 0x90000000, },
+	{ .ptr_type = 4, .addr = 0x83fd9014, .val = 0x00000000, },
+};
+
+#define APP_DEST	0x90000000
+
+struct imx_flash_header __flash_header_section flash_header = {
+	.app_code_jump_vector	= APP_DEST + 0x1000,
+	.app_code_barker	= APP_CODE_BARKER,
+	.app_code_csf		= 0,
+	.dcd_ptr_ptr		= APP_DEST + 0x400 + offsetof(struct imx_flash_header, dcd),
+	.super_root_key		= 0,
+	.dcd			= APP_DEST + 0x400 + offsetof(struct imx_flash_header, dcd_barker),
+	.app_dest		= APP_DEST,
+	.dcd_barker		= DCD_BARKER,
+	.dcd_block_len		= sizeof (dcd_entry),
+};
+
+unsigned long __image_len_section barebox_len = DCD_BAREBOX_SIZE;
+
diff --git a/arch/arm/configs/ccmx51_defconfig b/arch/arm/configs/ccmx51_defconfig
new file mode 100644
index 0000000000..d14de556b3
--- /dev/null
+++ b/arch/arm/configs/ccmx51_defconfig
@@ -0,0 +1,55 @@
+CONFIG_ARCH_IMX=y
+CONFIG_ARCH_IMX51=y
+CONFIG_MACH_CCMX51=y
+CONFIG_AEABI=y
+CONFIG_ARM_OPTIMZED_STRING_FUNCTIONS=y
+CONFIG_MALLOC_SIZE=0x2000000
+CONFIG_LONGHELP=y
+CONFIG_GLOB=y
+CONFIG_HUSH_FANCY_PROMPT=y
+CONFIG_CMDLINE_EDITING=y
+CONFIG_AUTO_COMPLETE=y
+CONFIG_PARTITION=y
+CONFIG_DEFAULT_ENVIRONMENT_GENERIC=y
+CONFIG_DEFAULT_ENVIRONMENT_PATH="defaultenv arch/arm/boards/ccxmx51/env"
+CONFIG_CMD_EDIT=y
+CONFIG_CMD_SLEEP=y
+CONFIG_CMD_SAVEENV=y
+CONFIG_CMD_LOADENV=y
+CONFIG_CMD_EXPORT=y
+CONFIG_CMD_PRINTENV=y
+CONFIG_CMD_READLINE=y
+CONFIG_CMD_ECHO_E=y
+CONFIG_CMD_MEMINFO=y
+CONFIG_CMD_MTEST=y
+CONFIG_CMD_FLASH=y
+CONFIG_CMD_BOOTM_ZLIB=y
+CONFIG_CMD_BOOTM_BZLIB=y
+CONFIG_CMD_BOOTM_SHOW_TYPE=y
+CONFIG_CMD_RESET=y
+CONFIG_CMD_GO=y
+CONFIG_CMD_TIMEOUT=y
+CONFIG_CMD_PARTITION=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_UNLZO=y
+CONFIG_CMD_I2C=y
+CONFIG_NET=y
+CONFIG_NET_DHCP=y
+CONFIG_NET_PING=y
+CONFIG_NET_TFTP=y
+CONFIG_DRIVER_NET_SMC911X=y
+CONFIG_DRIVER_NET_FEC_IMX=y
+CONFIG_DRIVER_SPI_IMX=y
+CONFIG_I2C=y
+CONFIG_I2C_IMX=y
+CONFIG_MTD=y
+CONFIG_NAND=y
+CONFIG_NAND_IMX=y
+CONFIG_USB=y
+CONFIG_USB_EHCI=y
+CONFIG_MCI=y
+# CONFIG_MCI_WRITE is not set
+CONFIG_MCI_IMX_ESDHC=y
+CONFIG_FS_CRAMFS=y
+CONFIG_FS_FAT=y
+CONFIG_FS_FAT_LFN=y
diff --git a/arch/arm/mach-imx/Kconfig b/arch/arm/mach-imx/Kconfig
index 564e2fe92d..15b7bfb918 100644
--- a/arch/arm/mach-imx/Kconfig
+++ b/arch/arm/mach-imx/Kconfig
@@ -26,6 +26,7 @@ config ARCH_TEXT_BASE
 	default 0x7ff00000 if MACH_TQMA53
 	default 0x97f00000 if MACH_TX51
 	default 0x4fc00000 if MACH_MX6Q_ARM2
+	default 0x97f00000 if MACH_CCMX51
 
 config BOARDINFO
 	default "Eukrea CPUIMX25" if MACH_EUKREA_CPUIMX25
@@ -50,6 +51,7 @@ config BOARDINFO
 	default "TQ tqma53" if MACH_TQMA53
 	default "Ka-Ro tx51" if MACH_TX51
 	default "Freescale i.MX6q armadillo2" if MACH_MX6Q_ARM2
+	default "ConnectCore i.MX51" if MACH_CCMX51
 
 choice
 	prompt "Select boot mode"
@@ -405,6 +407,23 @@ config MACH_TX51
 	help
 	  Say Y here if you are using the Ka-Ro tx51 board
 
+config MACH_CCMX51
+	bool "ConnectCore i.MX51"
+	select IMX_IIM
+	select SPI
+	select DRIVER_SPI_IMX
+	select MFD_MC13XXX
+	help
+	  Say Y here if you are using Digi ConnectCore (W)i-i.MX51
+	  equipped with a Freescale i.MX51 Processor
+
+config MACH_CCMX51_BASEBOARD
+	bool "Digi development board for CCMX51 module"
+	depends on MACH_CCMX51
+	default y
+	help
+	  This adds board specific devices that can be found on Digi
+	  evaluation board for CCMX51 module.
 
 endchoice