Add support for AMCC 440SPe CPU based eval board (Yucca).

9 files changed, 623 insertions, 70 deletions

diff --git a/cpu/ppc4xx/405gp_pci.c b/cpu/ppc4xx/405gp_pci.c
index 64431ab13a..2fda60e390 100644
--- a/cpu/ppc4xx/405gp_pci.c
+++ b/cpu/ppc4xx/405gp_pci.c
@@ -437,7 +437,7 @@ void pci_440_init (struct pci_controller *hose)
 	 * The PCI initialization sequence enable bit must be set ... if not abort
 	 * pci setup since updating the bit requires chip reset.
 	 *--------------------------------------------------------------------------*/
-#if defined(CONFIG_440GX) || defined(CONFIG_440SP)
+#if defined(CONFIG_440GX) || defined(CONFIG_440SP) || defined(CONFIG_440SPE)
 	unsigned long strap;
 
 	mfsdr(sdr_sdstp1,strap);
@@ -501,7 +501,7 @@ void pci_440_init (struct pci_controller *hose)
 	out16r( PCIX0_CLS, 0x00060000 ); /* Bridge, host bridge */
 #endif
 
-#if defined(CONFIG_440GX)
+#if defined(CONFIG_440GX) || defined(CONFIG_440SPE)
 	out32r( PCIX0_BRDGOPT1, 0x04000060 );               /* PLB Rq pri highest   */
 	out32r( PCIX0_BRDGOPT2, in32(PCIX0_BRDGOPT2) | 0x83 ); /* Enable host config, clear Timeout, ensure int src1  */
 #elif defined(PCIX0_BRDGOPT1)
@@ -519,8 +519,13 @@ void pci_440_init (struct pci_controller *hose)
 	out32r( PCIX0_POM0SA, 0 ); /* disable */
 	out32r( PCIX0_POM1SA, 0 ); /* disable */
 	out32r( PCIX0_POM2SA, 0 ); /* disable */
+#if defined(CONFIG_440SPE)
+	out32r( PCIX0_POM0LAL, 0x10000000 );
+	out32r( PCIX0_POM0LAH, 0x0000000c );
+#else
 	out32r( PCIX0_POM0LAL, 0x00000000 );
 	out32r( PCIX0_POM0LAH, 0x00000003 );
+#endif
 	out32r( PCIX0_POM0PCIAL, CFG_PCI_MEMBASE );
 	out32r( PCIX0_POM0PCIAH, 0x00000000 );
 	out32r( PCIX0_POM0SA, 0xf0000001 ); /* 256MB, enabled */
diff --git a/cpu/ppc4xx/4xx_enet.c b/cpu/ppc4xx/4xx_enet.c
index 86dc2d066e..fab65aff78 100644
--- a/cpu/ppc4xx/4xx_enet.c
+++ b/cpu/ppc4xx/4xx_enet.c
@@ -181,6 +181,9 @@ static void ppc_4xx_eth_halt (struct eth_device *dev)
 {
 	EMAC_4XX_HW_PST hw_p = dev->priv;
 	uint32_t failsafe = 10000;
+#if defined(CONFIG_440SPE)
+	unsigned long mfr;
+#endif
 
 	out32 (EMAC_IER + hw_p->hw_addr, 0x00000000);	/* disable emac interrupts */
 
@@ -202,8 +205,23 @@ static void ppc_4xx_eth_halt (struct eth_device *dev)
 	}
 
 	/* EMAC RESET */
+#if defined(CONFIG_440SPE)
+	/* provide clocks for EMAC internal loopback  */
+	mfsdr (sdr_mfr, mfr);
+	mfr |= 0x08000000;
+	mtsdr(sdr_mfr, mfr);
+#endif
+
 	out32 (EMAC_M0 + hw_p->hw_addr, EMAC_M0_SRST);
 
+#if defined(CONFIG_440SPE)
+	/* remove clocks for EMAC internal loopback  */
+	mfsdr (sdr_mfr, mfr);
+	mfr &= ~0x08000000;
+	mtsdr(sdr_mfr, mfr);
+#endif
+
+
 #ifndef CONFIG_NETCONSOLE
 	hw_p->print_speed = 1;	/* print speed message again next time */
 #endif
@@ -301,7 +319,7 @@ int ppc_4xx_eth_setup_bridge(int devnum, bd_t * bis)
 	return ((int)pfc1);
 
 }
-#endif
+#endif	/* CONFIG_440_GX */
 
 static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis)
 {
@@ -314,12 +332,16 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis)
 	unsigned mode_reg;
 	unsigned short devnum;
 	unsigned short reg_short;
-#if defined(CONFIG_440GX) || defined(CONFIG_440SP)
+#if defined(CONFIG_440GX) || defined(CONFIG_440SP) || defined(CONFIG_440SPE)
 	sys_info_t sysinfo;
-#if defined(CONFIG_440GX)
+#if defined(CONFIG_440GX) || defined(CONFIG_440SPE)
 	int ethgroup = -1;
 #endif
 #endif
+#if defined(CONFIG_440SPE)
+	unsigned long mfr;
+#endif
+
 
 	EMAC_4XX_HW_PST hw_p = dev->priv;
 
@@ -330,7 +352,7 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis)
 		return -1;
 	}
 
-#if defined(CONFIG_440GX) || defined(CONFIG_440SP)
+#if defined(CONFIG_440GX) || defined(CONFIG_440SP) || defined(CONFIG_440SPE)
 	/* Need to get the OPB frequency so we can access the PHY */
 	get_sys_info (&sysinfo);
 #endif
@@ -360,6 +382,7 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis)
 	hw_p->stats.pkts_tx = 0;
 	hw_p->stats.pkts_rx = 0;
 	hw_p->stats.pkts_handled = 0;
+	hw_p->print_speed = 1;	/* print speed message again next time */
 #endif
 
 	hw_p->tx_err_index = 0; /* Transmit Error Index for tx_err_log */
@@ -373,7 +396,7 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis)
 	hw_p->tx_i_index = 0;	/* Transmit Interrupt Queue Index */
 	hw_p->tx_u_index = 0;	/* Transmit User Queue Index */
 
-#if defined(CONFIG_440) && !defined(CONFIG_440SP)
+#if defined(CONFIG_440) && !defined(CONFIG_440SP) && !defined(CONFIG_440SPE)
 	/* set RMII mode */
 	/* NOTE: 440GX spec states that mode is mutually exclusive */
 	/* NOTE: Therefore, disable all other EMACS, since we handle */
@@ -406,6 +429,12 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis)
 	__asm__ volatile ("eieio");
 
 	/* reset emac so we have access to the phy */
+#if defined(CONFIG_440SPE)
+	/* provide clocks for EMAC internal loopback  */
+	mfsdr (sdr_mfr, mfr);
+	mfr |= 0x08000000;
+	mtsdr(sdr_mfr, mfr);
+#endif
 
 	out32 (EMAC_M0 + hw_p->hw_addr, EMAC_M0_SRST);
 	__asm__ volatile ("eieio");
@@ -416,7 +445,14 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis)
 		failsafe--;
 	}
 
-#if defined(CONFIG_440GX) || defined(CONFIG_440SP)
+#if defined(CONFIG_440SPE)
+	/* remove clocks for EMAC internal loopback  */
+	mfsdr (sdr_mfr, mfr);
+	mfr &= ~0x08000000;
+	mtsdr(sdr_mfr, mfr);
+#endif
+
+#if defined(CONFIG_440GX) || defined(CONFIG_440SP) || defined(CONFIG_440SPE)
 	/* Whack the M1 register */
 	mode_reg = 0x0;
 	mode_reg &= ~0x00000038;
@@ -468,7 +504,7 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis)
 	if (hw_p->first_init == 0) {
 		miiphy_reset (dev->name, reg);
 
-#if defined(CONFIG_440GX) || defined(CONFIG_440SP)
+#if defined(CONFIG_440GX) || defined(CONFIG_440SP) || defined(CONFIG_440SPE)
 #if defined(CONFIG_CIS8201_PHY)
 		/*
 		 * Cicada 8201 PHY needs to have an extended register whacked
@@ -544,7 +580,7 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis)
 			(int) speed, (duplex == HALF) ? "HALF" : "FULL");
 	}
 
-#if defined(CONFIG_440) && !defined(CONFIG_440SP)
+#if defined(CONFIG_440) && !defined(CONFIG_440SP) && !defined(CONFIG_440SPE)
 #if defined(CONFIG_440EP) || defined(CONFIG_440GR)
 	mfsdr(sdr_mfr, reg);
 	if (speed == 100) {
@@ -575,7 +611,7 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis)
 #endif /* defined(CONFIG_440) && !defined(CONFIG_440SP) */
 
 	/* set the Mal configuration reg */
-#if defined(CONFIG_440GX) || defined(CONFIG_440SP)
+#if defined(CONFIG_440GX) || defined(CONFIG_440SP) || defined(CONFIG_440SPE)
 	mtdcr (malmcr, MAL_CR_PLBB | MAL_CR_OPBBL | MAL_CR_LEA |
 	       MAL_CR_PLBLT_DEFAULT | MAL_CR_EOPIE | 0x00330000);
 #else
@@ -759,8 +795,7 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis)
 
 	/* set speed */
 	if (speed == _1000BASET) {
-#if defined(CONFIG_440SP)
-#define SDR0_PFC1_EM_1000	0x00200000
+#if defined(CONFIG_440SP) || defined(CONFIG_440SPE)
 		unsigned long pfc1;
 		mfsdr (sdr_pfc1, pfc1);
 		pfc1 |= SDR0_PFC1_EM_1000;
@@ -787,7 +822,7 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis)
 
 	/* set receive	low/high water mark register */
 #if defined(CONFIG_440)
-	/* 440GP has a 64 byte burst length */
+	/* 440s has a 64 byte burst length */
 	out32 (EMAC_RX_HI_LO_WMARK + hw_p->hw_addr, 0x80009000);
 #else
 	/* 405s have a 16 byte burst length */
@@ -895,7 +930,7 @@ static int ppc_4xx_eth_send (struct eth_device *dev, volatile void *ptr,
 
 #if defined (CONFIG_440)
 
-#if defined(CONFIG_440SP)
+#if defined(CONFIG_440SP) || defined(CONFIG_440SPE)
 /*
  * Hack: On 440SP all enet irq sources are located on UIC1
  * Needs some cleanup. --sr
@@ -1367,21 +1402,20 @@ int ppc_4xx_eth_initialize (bd_t * bis)
 #endif
 	/* set phy num and mode */
 	bis->bi_phynum[0] = CONFIG_PHY_ADDR;
+	bis->bi_phymode[0] = 0;
+
 #if defined(CONFIG_PHY1_ADDR)
 	bis->bi_phynum[1] = CONFIG_PHY1_ADDR;
+	bis->bi_phymode[1] = 0;
 #endif
 #if defined(CONFIG_440GX)
 	bis->bi_phynum[2] = CONFIG_PHY2_ADDR;
 	bis->bi_phynum[3] = CONFIG_PHY3_ADDR;
-	bis->bi_phymode[0] = 0;
-	bis->bi_phymode[1] = 0;
 	bis->bi_phymode[2] = 2;
 	bis->bi_phymode[3] = 2;
 
-#if defined (CONFIG_440GX)
 	ppc_4xx_eth_setup_bridge(0, bis);
 #endif
-#endif
 
 	for (eth_num = 0; eth_num < LAST_EMAC_NUM; eth_num++) {
 
@@ -1478,9 +1512,15 @@ int ppc_4xx_eth_initialize (bd_t * bis)
 
 		if (0 == virgin) {
 			/* set the MAL IER ??? names may change with new spec ??? */
+#if defined(CONFIG_440SPE)
+			mal_ier =
+				MAL_IER_PT | MAL_IER_PRE | MAL_IER_PWE |
+				MAL_IER_DE | MAL_IER_OTE | MAL_IER_OE | MAL_IER_PE ;
+#else
 			mal_ier =
 				MAL_IER_DE | MAL_IER_NE | MAL_IER_TE |
 				MAL_IER_OPBE | MAL_IER_PLBE;
+#endif
 			mtdcr (malesr, 0xffffffff);	/* clear pending interrupts */
 			mtdcr (maltxdeir, 0xffffffff);	/* clear pending interrupts */
 			mtdcr (malrxdeir, 0xffffffff);	/* clear pending interrupts */
@@ -1510,11 +1550,13 @@ int ppc_4xx_eth_initialize (bd_t * bis)
 #else
 		emac0_dev = dev;
 #endif
+
+#if defined(CONFIG_NET_MULTI)
 #if defined(CONFIG_MII) || (CONFIG_COMMANDS & CFG_CMD_MII)
 		miiphy_register (dev->name,
 				 emac4xx_miiphy_read, emac4xx_miiphy_write);
 #endif
-
+#endif
 	}			/* end for each supported device */
 	return (1);
 }
diff --git a/cpu/ppc4xx/cpu.c b/cpu/ppc4xx/cpu.c
index a26533c59c..3e85a88560 100644
--- a/cpu/ppc4xx/cpu.c
+++ b/cpu/ppc4xx/cpu.c
@@ -78,7 +78,9 @@ int pci_arbiter_enabled(void)
 	return (mfdcr(cpc0_strp1) & CPC0_STRP1_PAE_MASK);
 #endif
 
-#if defined(CONFIG_440GX) || defined(CONFIG_440EP) || defined(CONFIG_440GR) || defined(CONFIG_440SP)
+#if defined(CONFIG_440GX) || defined(CONFIG_440EP) || \
+     defined(CONFIG_440GR) || defined(CONFIG_440SP) || \
+     defined(CONFIG_440SPE)
 	unsigned long val;
 
 	mfsdr(sdr_sdstp1, val);
@@ -87,8 +89,8 @@ int pci_arbiter_enabled(void)
 }
 #endif
 
-#if defined(CONFIG_405EP)|| defined(CONFIG_440EP) || defined(CONFIG_440GR) || \
-	defined(CONFIG_440GX) || defined(CONFIG_440SP)
+#if defined(CONFIG_405EP) || defined(CONFIG_440EP) || defined(CONFIG_440GR) ||  \
+     defined(CONFIG_440GX) || defined(CONFIG_440SP) || defined(CONFIG_440SPE)
 
 #define I2C_BOOTROM
 
@@ -98,7 +100,9 @@ int i2c_bootrom_enabled(void)
 	return (mfdcr(cpc0_boot) & CPC0_BOOT_SEP);
 #endif
 
-#if defined(CONFIG_440GX) || defined(CONFIG_440EP) || defined(CONFIG_440GR) || defined(CONFIG_440SP)
+#if defined(CONFIG_440GX) || defined(CONFIG_440EP) || \
+     defined(CONFIG_440GR) || defined(CONFIG_440SP) || \
+	defined(CONFIG_440SPE)
 	unsigned long val;
 
 	mfsdr(sdr_sdcs, val);
@@ -237,6 +241,12 @@ int checkcpu (void)
 		puts("SP Rev. B");
 		break;
 
+	case PVR_440SPe_RA:
+		puts("SPe 3GA533C");
+		break;
+	case PVR_440SPe_RB:
+		puts("SPe 3GB533C");
+		break;
 	default:
 		printf (" UNKNOWN (PVR=%08x)", pvr);
 		break;
diff --git a/cpu/ppc4xx/interrupts.c b/cpu/ppc4xx/interrupts.c
index 1d8dc7c221..fdae846dcc 100644
--- a/cpu/ppc4xx/interrupts.c
+++ b/cpu/ppc4xx/interrupts.c
@@ -48,18 +48,22 @@ struct	irq_action {
 };
 
 static struct irq_action irq_vecs[32];
+void uic0_interrupt( void * parms); /* UIC0 handler */
 
 #if defined(CONFIG_440)
 static struct irq_action irq_vecs1[32]; /* For UIC1 */
 
 void uic1_interrupt( void * parms); /* UIC1 handler */
 
-#if defined(CONFIG_440GX)
+#if defined(CONFIG_440GX) || defined(CONFIG_440SPE)
 static struct irq_action irq_vecs2[32]; /* For UIC2 */
-
-void uic0_interrupt( void * parms); /* UIC0 handler */
 void uic2_interrupt( void * parms); /* UIC2 handler */
-#endif /* CONFIG_440GX */
+#endif /* CONFIG_440GX CONFIG_440SPE */
+
+#if defined(CONFIG_440SPE)
+static struct irq_action irq_vecs3[32]; /* For UIC3 */
+void uic3_interrupt( void * parms); /* UIC3 handler */
+#endif /* CONFIG_440SPE */
 
 #endif /* CONFIG_440 */
 
@@ -115,11 +119,16 @@ int interrupt_init_cpu (unsigned *decrementer_count)
 		irq_vecs1[vec].handler = NULL;
 		irq_vecs1[vec].arg = NULL;
 		irq_vecs1[vec].count = 0;
-#if defined(CONFIG_440GX)
+#if defined(CONFIG_440GX) || defined(CONFIG_440SPE)
 		irq_vecs2[vec].handler = NULL;
 		irq_vecs2[vec].arg = NULL;
 		irq_vecs2[vec].count = 0;
 #endif /* CONFIG_440GX */
+#if defined(CONFIG_440SPE)
+		irq_vecs3[vec].handler = NULL;
+		irq_vecs3[vec].arg = NULL;
+		irq_vecs3[vec].count = 0;
+#endif /* CONFIG_440SPE */
 #endif
 	}
 
@@ -221,6 +230,34 @@ void external_interrupt(struct pt_regs *regs)
 
 } /* external_interrupt CONFIG_440GX */
 
+#elif defined(CONFIG_440SPE)
+void external_interrupt(struct pt_regs *regs)
+{
+	ulong uic_msr;
+
+	/*
+	 * Read masked interrupt status register to determine interrupt source
+	 */
+	/* 440 SPe uses base uic register */
+	uic_msr = mfdcr(uic0msr);
+
+	if ( (UICB0_UIC1CI & uic_msr) || (UICB0_UIC1NCI & uic_msr) )
+		uic1_interrupt(0);
+
+	if ( (UICB0_UIC2CI & uic_msr) || (UICB0_UIC2NCI & uic_msr) )
+		uic2_interrupt(0);
+
+	if ( (UICB0_UIC3CI & uic_msr) || (UICB0_UIC3NCI & uic_msr) )
+		uic3_interrupt(0);
+
+	if (uic_msr & ~(UICB0_ALL))
+		uic0_interrupt(0);
+
+	mtdcr(uic0sr, uic_msr);
+
+	return;
+} /* external_interrupt CONFIG_440SPE */
+
 #else
 
 void external_interrupt(struct pt_regs *regs)
@@ -266,7 +303,7 @@ void external_interrupt(struct pt_regs *regs)
 }
 #endif
 
-#if defined(CONFIG_440GX)
+#if defined(CONFIG_440GX) || defined(CONFIG_440SPE)
 /* Handler for UIC0 interrupt */
 void uic0_interrupt( void * parms)
 {
@@ -357,8 +394,8 @@ void uic1_interrupt( void * parms)
 }
 #endif /* defined(CONFIG_440) */
 
-#if defined(CONFIG_440GX)
-/* Handler for UIC1 interrupt */
+#if defined(CONFIG_440GX) || defined(CONFIG_440SPE)
+/* Handler for UIC2 interrupt */
 void uic2_interrupt( void * parms)
 {
 	ulong uic2_msr;
@@ -384,7 +421,7 @@ void uic2_interrupt( void * parms)
 				(*irq_vecs2[vec].handler)(irq_vecs2[vec].arg);
 			} else {
 				mtdcr(uic2er, mfdcr(uic2er) & ~(0x80000000 >> vec));
-				printf ("Masking bogus interrupt vector (uic1) 0x%x\n", vec);
+				printf ("Masking bogus interrupt vector (uic2) 0x%x\n", vec);
 			}
 
 			/*
@@ -402,6 +439,51 @@ void uic2_interrupt( void * parms)
 }
 #endif /* defined(CONFIG_440GX) */
 
+#if defined(CONFIG_440SPE)
+/* Handler for UIC3 interrupt */
+void uic3_interrupt( void * parms)
+{
+	ulong uic3_msr;
+	ulong msr_shift;
+	int vec;
+
+	/*
+	 * Read masked interrupt status register to determine interrupt source
+	 */
+	uic3_msr = mfdcr(uic3msr);
+	msr_shift = uic3_msr;
+	vec = 0;
+
+	while (msr_shift != 0) {
+		if (msr_shift & 0x80000000) {
+			/*
+			 * Increment irq counter (for debug purpose only)
+			 */
+			irq_vecs3[vec].count++;
+
+			if (irq_vecs3[vec].handler != NULL) {
+				/* call isr */
+				(*irq_vecs3[vec].handler)(irq_vecs3[vec].arg);
+			} else {
+				mtdcr(uic3er, mfdcr(uic3er) & ~(0x80000000 >> vec));
+				printf ("Masking bogus interrupt vector (uic3) 0x%x\n", vec);
+			}
+
+			/*
+			 * After servicing the interrupt, we have to remove the status indicator.
+			 */
+			mtdcr(uic3sr, (0x80000000 >> vec));
+		}
+
+		/*
+		 * Shift msr to next position and increment vector
+		 */
+		msr_shift <<= 1;
+		vec++;
+	}
+}
+#endif /* defined(CONFIG_440SPE) */
+
 /****************************************************************************/
 
 /*
@@ -414,7 +496,7 @@ void irq_install_handler (int vec, interrupt_handler_t * handler, void *arg)
 	int i = vec;
 
 #if defined(CONFIG_440)
-#if defined(CONFIG_440GX)
+#if defined(CONFIG_440GX) || defined(CONFIG_440SPE)
 	if ((vec > 31) && (vec < 64)) {
 		i = vec - 32;
 		irqa = irq_vecs1;
@@ -441,7 +523,7 @@ void irq_install_handler (int vec, interrupt_handler_t * handler, void *arg)
 	irqa[i].arg = arg;
 
 #if defined(CONFIG_440)
-#if defined(CONFIG_440GX)
+#if defined(CONFIG_440GX) || defined(CONFIG_440SPE)
 	if ((vec > 31) && (vec < 64))
 		mtdcr (uic1er, mfdcr (uic1er) | (0x80000000 >> i));
 	else if (vec > 63)
@@ -464,7 +546,7 @@ void irq_free_handler (int vec)
 	int i = vec;
 
 #if defined(CONFIG_440)
-#if defined(CONFIG_440GX)
+#if defined(CONFIG_440GX) || defined(CONFIG_440SPE)
 	if ((vec > 31) && (vec < 64)) {
 		irqa = irq_vecs1;
 		i = vec - 32;
@@ -485,7 +567,7 @@ void irq_free_handler (int vec)
 #endif
 
 #if defined(CONFIG_440)
-#if defined(CONFIG_440GX)
+#if defined(CONFIG_440GX) || defined(CONFIG_440SPE)
 	if ((vec > 31) && (vec < 64))
 		mtdcr (uic1er, mfdcr (uic1er) & ~(0x80000000 >> i));
 	else if (vec > 63)
@@ -553,7 +635,7 @@ do_irqinfo(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 	printf("\n");
 #endif
 
-#if defined(CONFIG_440GX)
+#if defined(CONFIG_440GX) || defined(CONFIG_440SPE)
 	printf ("\nUIC 2\n");
 	printf ("Nr  Routine   Arg       Count\n");
 
@@ -566,6 +648,19 @@ do_irqinfo(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 	printf("\n");
 #endif
 
+#if defined(CONFIG_440SPE)
+	printf ("\nUIC 3\n");
+	printf ("Nr  Routine   Arg       Count\n");
+
+	for (vec=0; vec<32; vec++) {
+		if (irq_vecs3[vec].handler != NULL)
+			printf ("%02d  %08lx  %08lx  %d\n",
+					vec+63, (ulong)irq_vecs3[vec].handler,
+					(ulong)irq_vecs3[vec].arg, irq_vecs3[vec].count);
+	}
+	printf("\n");
+#endif
+
 	return 0;
 }
 #endif  /* CONFIG_COMMANDS & CFG_CMD_IRQ */
diff --git a/cpu/ppc4xx/miiphy.c b/cpu/ppc4xx/miiphy.c
index f26f2a203a..aa580ed48f 100644
--- a/cpu/ppc4xx/miiphy.c
+++ b/cpu/ppc4xx/miiphy.c
@@ -50,7 +50,7 @@
 #include <405_mal.h>
 #include <miiphy.h>
 
-
+#undef ET_DEBUG
 /***********************************************************/
 /* Dump out to the screen PHY regs			   */
 /***********************************************************/
@@ -90,6 +90,10 @@ int phy_setup_aneg (char *devname, unsigned char addr)
 		PHY_ANLPAR_10);
 	miiphy_write (devname, addr, PHY_ANAR, adv);
 
+	miiphy_read (devname, addr, PHY_1000BTCR, &adv);
+	adv |= (0x0300);
+	miiphy_write (devname, addr, PHY_1000BTCR, adv);
+
 	/* Start/Restart aneg */
 	miiphy_read (devname, addr, PHY_BMCR, &ctl);
 	ctl |= (PHY_BMCR_AUTON | PHY_BMCR_RST_NEG);
@@ -104,7 +108,7 @@ int phy_setup_aneg (char *devname, unsigned char addr)
 /***********************************************************/
 unsigned int miiphy_getemac_offset (void)
 {
-#if (defined(CONFIG_440) && !defined(CONFIG_440SP)) && defined(CONFIG_NET_MULTI)
+#if (defined(CONFIG_440) && !defined(CONFIG_440SP) && !defined(CONFIG_440SPE)) && defined(CONFIG_NET_MULTI)
 	unsigned long zmii;
 	unsigned long eoffset;
 
@@ -155,10 +159,12 @@ int emac4xx_miiphy_read (char *devname, unsigned char addr,
 	i = 0;
 
 	/* see if it is ready for  sec */
-	while ((in32 (EMAC_STACR + emac_reg) & EMAC_STACR_OC) == 0) {
+	while ((in32 (EMAC_STACR + emac_reg) & EMAC_STACR_OC) == EMAC_STACR_OC_MASK) {
 		udelay (7);
 		if (i > 5) {
-#if 0
+#ifdef ET_DEBUG
+			sta_reg = in32 (EMAC_STACR + emac_reg);
+			printf ("read : EMAC_STACR=0x%0x\n", sta_reg);	/* test-only */
 			printf ("read err 1\n");
 #endif
 			return -1;
@@ -167,31 +173,41 @@ int emac4xx_miiphy_read (char *devname, unsigned char addr,
 	}
 	sta_reg = reg;		/* reg address */
 	/* set clock (50Mhz) and read flags */
-#if defined(CONFIG_440GX)
-	sta_reg |= EMAC_STACR_READ;
+#if defined(CONFIG_440GX) || defined(CONFIG_440SPE)
+#if defined(CONFIG_IBM_EMAC4_V4)      /* EMAC4 V4 changed bit setting */
+		sta_reg = (sta_reg & ~EMAC_STACR_OP_MASK) | EMAC_STACR_READ;
+#else
+		sta_reg |= EMAC_STACR_READ;
+#endif
 #else
 	sta_reg = (sta_reg | EMAC_STACR_READ) & ~EMAC_STACR_CLK_100MHZ;
 #endif
 
-#if defined(CONFIG_PHY_CLK_FREQ) && !defined(CONFIG_440GX)
+#if defined(CONFIG_PHY_CLK_FREQ) && !defined(CONFIG_440GX) && !defined(CONFIG__440SP) && !defined(CONFIG__440SPE)
 	sta_reg = sta_reg | CONFIG_PHY_CLK_FREQ;
 #endif
 	sta_reg = sta_reg | (addr << 5);	/* Phy address */
-
+	sta_reg = sta_reg | EMAC_STACR_OC_MASK;	/* new IBM emac v4 */
 	out32 (EMAC_STACR + emac_reg, sta_reg);
-#if 0				/* test-only */
+#ifdef ET_DEBUG
 	printf ("a2: write: EMAC_STACR=0x%0x\n", sta_reg);	/* test-only */
 #endif
 
 	sta_reg = in32 (EMAC_STACR + emac_reg);
+#ifdef ET_DEBUG
+		printf ("a21: read : EMAC_STACR=0x%0x\n", sta_reg);	/* test-only */
+#endif
 	i = 0;
-	while ((sta_reg & EMAC_STACR_OC) == 0) {
+	while ((sta_reg & EMAC_STACR_OC) == EMAC_STACR_OC_MASK) {
 		udelay (7);
 		if (i > 5) {
 			return -1;
 		}
 		i++;
 		sta_reg = in32 (EMAC_STACR + emac_reg);
+#ifdef ET_DEBUG
+		printf ("a22: read : EMAC_STACR=0x%0x\n", sta_reg);	/* test-only */
+#endif
 	}
 	if ((sta_reg & EMAC_STACR_PHYE) != 0) {
 		return -1;
@@ -219,7 +235,7 @@ int emac4xx_miiphy_write (char *devname, unsigned char addr,
 	/* see if it is ready for 1000 nsec */
 	i = 0;
 
-	while ((in32 (EMAC_STACR + emac_reg) & EMAC_STACR_OC) == 0) {
+	while ((in32 (EMAC_STACR + emac_reg) & EMAC_STACR_OC) == EMAC_STACR_OC_MASK) {
 		if (i > 5)
 			return -1;
 		udelay (7);
@@ -228,16 +244,21 @@ int emac4xx_miiphy_write (char *devname, unsigned char addr,
 	sta_reg = 0;
 	sta_reg = reg;		/* reg address */
 	/* set clock (50Mhz) and read flags */
-#if defined(CONFIG_440GX)
-	sta_reg |= EMAC_STACR_WRITE;
+#if defined(CONFIG_440GX) || defined(CONFIG_440SPE)
+#if defined(CONFIG_IBM_EMAC4_V4)      /* EMAC4 V4 changed bit setting */
+		sta_reg = (sta_reg & ~EMAC_STACR_OP_MASK) | EMAC_STACR_WRITE;
+#else
+		sta_reg |= EMAC_STACR_WRITE;
+#endif
 #else
 	sta_reg = (sta_reg | EMAC_STACR_WRITE) & ~EMAC_STACR_CLK_100MHZ;
 #endif
 
-#if defined(CONFIG_PHY_CLK_FREQ) && !defined(CONFIG_440GX)
+#if defined(CONFIG_PHY_CLK_FREQ) && !defined(CONFIG_440GX) && !defined(CONFIG__440SP) && !defined(CONFIG__440SPE)
 	sta_reg = sta_reg | CONFIG_PHY_CLK_FREQ;	/* Set clock frequency (PLB freq. dependend) */
 #endif
-	sta_reg = sta_reg | ((unsigned long) addr << 5);	/* Phy address */
+	sta_reg = sta_reg | ((unsigned long) addr << 5);/* Phy address */
+	sta_reg = sta_reg | EMAC_STACR_OC_MASK;		/* new IBM emac v4 */
 	memcpy (&sta_reg, &value, 2);	/* put in data */
 
 	out32 (EMAC_STACR + emac_reg, sta_reg);
@@ -245,12 +266,18 @@ int emac4xx_miiphy_write (char *devname, unsigned char addr,
 	/* wait for completion */
 	i = 0;
 	sta_reg = in32 (EMAC_STACR + emac_reg);
-	while ((sta_reg & EMAC_STACR_OC) == 0) {
+#ifdef ET_DEBUG
+		printf ("a31: read : EMAC_STACR=0x%0x\n", sta_reg);	/* test-only */
+#endif
+	while ((sta_reg & EMAC_STACR_OC) == EMAC_STACR_OC_MASK) {
 		udelay (7);
 		if (i > 5)
 			return -1;
 		i++;
 		sta_reg = in32 (EMAC_STACR + emac_reg);
+#ifdef ET_DEBUG
+		printf ("a32: read : EMAC_STACR=0x%0x\n", sta_reg);	/* test-only */
+#endif
 	}
 
 	if ((sta_reg & EMAC_STACR_PHYE) != 0)
diff --git a/cpu/ppc4xx/serial.c b/cpu/ppc4xx/serial.c
index e7f6bcbe1e..2734520987 100644
--- a/cpu/ppc4xx/serial.c
+++ b/cpu/ppc4xx/serial.c
@@ -277,11 +277,11 @@ int serial_tstc ()
 #define UART1_BASE  CFG_PERIPHERAL_BASE + 0x00000300
 #endif
 
-#if defined(CONFIG_440SP)
+#if defined(CONFIG_440SP) || defined(CONFIG_440SPE)
 #define UART2_BASE  CFG_PERIPHERAL_BASE + 0x00000600
 #endif
 
-#if defined(CONFIG_440GX) || defined(CONFIG_440EP) || defined(CONFIG_440GR) || defined(CONFIG_440SP)
+#if defined(CONFIG_440GX) || defined(CONFIG_440EP) || defined(CONFIG_440GR) || defined(CONFIG_440SP) || defined(CONFIG_440SPE)
 #define CR0_MASK        0xdfffffff
 #define CR0_EXTCLK_ENA  0x00800000
 #define CR0_UDIV_POS    0
@@ -311,14 +311,18 @@ int serial_tstc ()
 #if defined(CONFIG_UART1_CONSOLE)
 #define ACTING_UART0_BASE	UART1_BASE
 #define ACTING_UART1_BASE	UART0_BASE
-#if defined(CONFIG_440GX) || defined(CONFIG_440EP) || defined(CONFIG_440GR) || defined(CONFIG_440SP)
+#if defined(CONFIG_440GX) || defined(CONFIG_440EP) || \
+	defined(CONFIG_440GR) || defined(CONFIG_440SP) || \
+	defined(CONFIG_440SPE)
 #define UART0_SDR           sdr_uart1
 #define UART1_SDR           sdr_uart0
 #endif /* CONFIG_440GX */
 #else
 #define ACTING_UART0_BASE	UART0_BASE
 #define ACTING_UART1_BASE	UART1_BASE
-#if defined(CONFIG_440GX) || defined(CONFIG_440EP) || defined(CONFIG_440GR) || defined(CONFIG_440SP)
+#if defined(CONFIG_440GX) || defined(CONFIG_440EP) || \
+	defined(CONFIG_440GR) || defined(CONFIG_440SP) || \
+	defined(CONFIG_440SPE)
 #define UART0_SDR           sdr_uart0
 #define UART1_SDR           sdr_uart1
 #endif /* CONFIG_440GX */
@@ -441,7 +445,8 @@ int serial_init(void)
 	unsigned long tmp;
 #endif
 
-#if defined(CONFIG_440GX) || defined(CONFIG_440SP)
+#if defined(CONFIG_440GX) || defined(CONFIG_440SP) || \
+	defined(CONFIG_440SPE)
 #if defined(CONFIG_SERIAL_MULTI)
 	if (UART0_BASE == dev_base) {
 		mfsdr(UART0_SDR,reg);
@@ -470,7 +475,9 @@ int serial_init(void)
 	serial_divs (gd->baudrate, &udiv, &bdiv);
 #endif
 
-#if defined(CONFIG_440GX) || defined(CONFIG_440EP) || defined(CONFIG_440GR) || defined(CONFIG_440SP)
+#if defined(CONFIG_440GX) || defined(CONFIG_440EP) || \
+	defined(CONFIG_440GR) || defined(CONFIG_440SP) || \
+	defined(CONFIG_440SPE)
 	reg |= udiv << CR0_UDIV_POS;	/* set the UART divisor */
 #if defined(CONFIG_SERIAL_MULTI)
 	if (UART0_BASE == dev_base) {
@@ -615,8 +622,28 @@ void serial_setbrg (void)
 #else
 	udiv = ((mfdcr (cntrl0) & 0x3e) >> 1) + 1;
 #endif /* CONFIG_405EP */
+
+#if !defined(CFG_EXT_SERIAL_CLOCK) && \
+	( defined(CONFIG_440GX) || defined(CONFIG_440EP) || \
+	  defined(CONFIG_440GR) || defined(CONFIG_440SP) || \
+	  defined(CONFIG_440SPE) )
+	serial_divs (gd->baudrate, &udiv, &bdiv);
+	tmp = udiv << CR0_UDIV_POS;		/* set the UART divisor */
+#if defined(CONFIG_SERIAL_MULTI)
+	if (UART0_BASE == dev_base) {
+		mtsdr (UART0_SDR, tmp);
+	} else {
+		mtsdr (UART1_SDR, tmp);
+	}
+#else
+	mtsdr (UART0_SDR, tmp);
+#endif
+
+#else
+
 	tmp = gd->baudrate * udiv * 16;
 	bdiv = (clk + tmp / 2) / tmp;
+#endif /* !defined(CFG_EXT_SERIAL_CLOCK) && (...) */ 
 
 #if defined(CONFIG_SERIAL_MULTI)
 	out8 (dev_base + UART_LCR, 0x80);	/* set DLAB bit */
diff --git a/cpu/ppc4xx/speed.c b/cpu/ppc4xx/speed.c
index 553c491e24..7778271932 100644
--- a/cpu/ppc4xx/speed.c
+++ b/cpu/ppc4xx/speed.c
@@ -29,7 +29,11 @@
 /* ------------------------------------------------------------------------- */
 
 #define ONE_BILLION        1000000000
-
+#ifdef DEBUG
+#define DEBUGF(fmt,args...) printf(fmt ,##args)
+#else
+#define DEBUGF(fmt,args...)
+#endif
 
 #if defined(CONFIG_405GP) || defined(CONFIG_405CR)
 
@@ -283,7 +287,7 @@ ulong get_PCI_freq (void)
 	return sys_info.freqPCI;
 }
 
-#elif !defined(CONFIG_440GX) && !defined(CONFIG_440SP)
+#elif !defined(CONFIG_440GX) && !defined(CONFIG_440SP) && !defined(CONFIG_440SPE)
 void get_sys_info (sys_info_t * sysInfo)
 {
 	unsigned long strp0;
@@ -326,6 +330,26 @@ void get_sys_info (sys_info_t * sysInfo)
 	unsigned long m;
 	unsigned long prbdv0;
 
+#if defined(CONFIG_440SPE)
+	unsigned long sys_freq;
+	unsigned long sys_per=0;
+	unsigned long msr;
+	unsigned long pci_clock_per;
+	unsigned long sdr_ddrpll;
+
+	/*-------------------------------------------------------------------------+
+	 | Get the system clock period.
+	 +-------------------------------------------------------------------------*/
+	sys_per = determine_sysper();
+
+	msr = (mfmsr () & ~(MSR_EE));	/* disable interrupts */
+
+	/*-------------------------------------------------------------------------+
+	 | Calculate the system clock speed from the period.
+	 +-------------------------------------------------------------------------*/
+	sys_freq=(ONE_BILLION/sys_per)*1000;
+#endif
+
 	/* Extract configured divisors */
 	mfsdr( sdr_sdstp0,strp0 );
 	mfsdr( sdr_sdstp1,strp1 );
@@ -360,12 +384,238 @@ void get_sys_info (sys_info_t * sysInfo)
 		m = sysInfo->pllExtBusDiv * sysInfo->pllOpbDiv * sysInfo->pllFwdDivB;
 
 	/* Now calculate the individual clocks */
+#if defined(CONFIG_440SPE)
+	sysInfo->freqVCOMhz = (m * sys_freq) ;
+#else
 	sysInfo->freqVCOMhz = (m * CONFIG_SYS_CLK_FREQ) + (m>>1);
+#endif
 	sysInfo->freqProcessor = sysInfo->freqVCOMhz/sysInfo->pllFwdDivA;
 	sysInfo->freqPLB = sysInfo->freqVCOMhz/sysInfo->pllFwdDivB/prbdv0;
 	sysInfo->freqOPB = sysInfo->freqPLB/sysInfo->pllOpbDiv;
 	sysInfo->freqEPB = sysInfo->freqOPB/sysInfo->pllExtBusDiv;
 
+#if defined(CONFIG_440SPE)
+	/* Determine PCI Clock Period */
+	pci_clock_per = determine_pci_clock_per();
+	sysInfo->freqPCI = (ONE_BILLION/pci_clock_per) * 1000;
+	mfsdr(sdr_ddr0, sdr_ddrpll);
+	sysInfo->freqDDR = ((sysInfo->freqPLB) * SDR0_DDR0_DDRM_DECODE(sdr_ddrpll));
+#endif
+
+
+}
+
+#endif
+
+#if defined(CONFIG_440SPE)
+unsigned long determine_sysper(void)
+{
+	unsigned int fpga_clocking_reg;
+	unsigned int master_clock_selection;
+	unsigned long master_clock_per = 0;
+	unsigned long fb_div_selection;
+	unsigned int vco_div_reg_value;
+	unsigned long vco_div_selection;
+	unsigned long sys_per = 0;
+	int extClkVal;
+
+	/*-------------------------------------------------------------------------+
+	 | Read FPGA reg 0 and reg 1 to get FPGA reg information
+	 +-------------------------------------------------------------------------*/
+	fpga_clocking_reg = in16(FPGA_REG16);
+
+
+	/* Determine Master Clock Source Selection */
+	master_clock_selection = fpga_clocking_reg & FPGA_REG16_MASTER_CLK_MASK;
+
+	switch(master_clock_selection) {
+		case FPGA_REG16_MASTER_CLK_66_66:
+			master_clock_per = PERIOD_66_66MHZ;
+			break;
+		case FPGA_REG16_MASTER_CLK_50:
+			master_clock_per = PERIOD_50_00MHZ;
+			break;
+		case FPGA_REG16_MASTER_CLK_33_33:
+			master_clock_per = PERIOD_33_33MHZ;
+			break;
+		case FPGA_REG16_MASTER_CLK_25:
+			master_clock_per = PERIOD_25_00MHZ;
+			break;
+		case FPGA_REG16_MASTER_CLK_EXT:
+			if ((extClkVal==EXTCLK_33_33)
+					&& (extClkVal==EXTCLK_50)
+					&& (extClkVal==EXTCLK_66_66)
+					&& (extClkVal==EXTCLK_83)) {
+				/* calculate master clock period from external clock value */
+				master_clock_per=(ONE_BILLION/extClkVal) * 1000;
+			} else {
+				/* Unsupported */
+				DEBUGF ("%s[%d] *** master clock selection failed ***\n", __FUNCTION__,__LINE__);
+				hang();
+			}
+			break;
+		default:
+			/* Unsupported */
+			DEBUGF ("%s[%d] *** master clock selection failed ***\n", __FUNCTION__,__LINE__);
+			hang();
+			break;
+	}
+
+	/* Determine FB divisors values */
+	if ((fpga_clocking_reg & FPGA_REG16_FB1_DIV_MASK) == FPGA_REG16_FB1_DIV_LOW) {
+		if ((fpga_clocking_reg & FPGA_REG16_FB2_DIV_MASK) == FPGA_REG16_FB2_DIV_LOW)
+			fb_div_selection = FPGA_FB_DIV_6;
+		else
+			fb_div_selection = FPGA_FB_DIV_12;
+	} else {
+		if ((fpga_clocking_reg & FPGA_REG16_FB2_DIV_MASK) == FPGA_REG16_FB2_DIV_LOW)
+			fb_div_selection = FPGA_FB_DIV_10;
+		else
+			fb_div_selection = FPGA_FB_DIV_20;
+	}
+
+	/* Determine VCO divisors values */
+	vco_div_reg_value = fpga_clocking_reg & FPGA_REG16_VCO_DIV_MASK;
+
+	switch(vco_div_reg_value) {
+		case FPGA_REG16_VCO_DIV_4:
+			vco_div_selection = FPGA_VCO_DIV_4;
+			break;
+		case FPGA_REG16_VCO_DIV_6:
+			vco_div_selection = FPGA_VCO_DIV_6;
+			break;
+		case FPGA_REG16_VCO_DIV_8:
+			vco_div_selection = FPGA_VCO_DIV_8;
+			break;
+		case FPGA_REG16_VCO_DIV_10:
+		default:
+			vco_div_selection = FPGA_VCO_DIV_10;
+			break;
+	}
+
+	if (master_clock_selection == FPGA_REG16_MASTER_CLK_EXT) {
+		switch(master_clock_per) {
+			case PERIOD_25_00MHZ:
+				if (fb_div_selection == FPGA_FB_DIV_12) {
+					if (vco_div_selection == FPGA_VCO_DIV_4)
+						sys_per = PERIOD_75_00MHZ;
+					if (vco_div_selection == FPGA_VCO_DIV_6)
+						sys_per = PERIOD_50_00MHZ;
+				}
+				break;
+			case PERIOD_33_33MHZ:
+				if (fb_div_selection == FPGA_FB_DIV_6) {
+					if (vco_div_selection == FPGA_VCO_DIV_4)
+						sys_per = PERIOD_50_00MHZ;
+					if (vco_div_selection == FPGA_VCO_DIV_6)
+						sys_per = PERIOD_33_33MHZ;
+				}
+				if (fb_div_selection == FPGA_FB_DIV_10) {
+					if (vco_div_selection == FPGA_VCO_DIV_4)
+						sys_per = PERIOD_83_33MHZ;
+					if (vco_div_selection == FPGA_VCO_DIV_10)
+						sys_per = PERIOD_33_33MHZ;
+				}
+				if (fb_div_selection == FPGA_FB_DIV_12) {
+					if (vco_div_selection == FPGA_VCO_DIV_4)
+						sys_per = PERIOD_100_00MHZ;
+					if (vco_div_selection == FPGA_VCO_DIV_6)
+						sys_per = PERIOD_66_66MHZ;
+					if (vco_div_selection == FPGA_VCO_DIV_8)
+						sys_per = PERIOD_50_00MHZ;
+				}
+				break;
+			case PERIOD_50_00MHZ:
+				if (fb_div_selection == FPGA_FB_DIV_6) {
+					if (vco_div_selection == FPGA_VCO_DIV_4)
+						sys_per = PERIOD_75_00MHZ;
+					if (vco_div_selection == FPGA_VCO_DIV_6)
+						sys_per = PERIOD_50_00MHZ;
+				}
+				if (fb_div_selection == FPGA_FB_DIV_10) {
+					if (vco_div_selection == FPGA_VCO_DIV_6)
+						sys_per = PERIOD_83_33MHZ;
+					if (vco_div_selection == FPGA_VCO_DIV_10)
+						sys_per = PERIOD_50_00MHZ;
+				}
+				if (fb_div_selection == FPGA_FB_DIV_12) {
+					if (vco_div_selection == FPGA_VCO_DIV_6)
+						sys_per = PERIOD_100_00MHZ;
+					if (vco_div_selection == FPGA_VCO_DIV_8)
+						sys_per = PERIOD_75_00MHZ;
+				}
+				break;
+			case PERIOD_66_66MHZ:
+				if (fb_div_selection == FPGA_FB_DIV_6) {
+					if (vco_div_selection == FPGA_VCO_DIV_4)
+						sys_per = PERIOD_100_00MHZ;
+					if (vco_div_selection == FPGA_VCO_DIV_6)
+						sys_per = PERIOD_66_66MHZ;
+					if (vco_div_selection == FPGA_VCO_DIV_8)
+						sys_per = PERIOD_50_00MHZ;
+				}
+				if (fb_div_selection == FPGA_FB_DIV_10) {
+					if (vco_div_selection == FPGA_VCO_DIV_8)
+						sys_per = PERIOD_83_33MHZ;
+					if (vco_div_selection == FPGA_VCO_DIV_10)
+						sys_per = PERIOD_66_66MHZ;
+				}
+				if (fb_div_selection == FPGA_FB_DIV_12) {
+					if (vco_div_selection == FPGA_VCO_DIV_8)
+						sys_per = PERIOD_100_00MHZ;
+				}
+				break;
+			default:
+				break;
+		}
+
+		if (sys_per == 0) {
+			/* Other combinations are not supported */
+			DEBUGF ("%s[%d] *** sys period compute failed ***\n", __FUNCTION__,__LINE__);
+			hang();
+		}
+	} else {
+		/* calcul system clock without cheking */
+		/* if engineering option clock no check is selected */
+		/* sys_per = master_clock_per * vco_div_selection / fb_div_selection */
+		sys_per = (master_clock_per/fb_div_selection) * vco_div_selection;
+	}
+
+	return(sys_per);
+
+}
+
+/*-------------------------------------------------------------------------+
+| determine_pci_clock_per.
++-------------------------------------------------------------------------*/
+unsigned long determine_pci_clock_per(void)
+{
+	unsigned long pci_clock_selection,  pci_period;
+
+	/*-------------------------------------------------------------------------+
+	 | Read FPGA reg 6 to get PCI 0 FPGA reg information
+	 +-------------------------------------------------------------------------*/
+	pci_clock_selection = in16(FPGA_REG16);	/* was reg6 averifier */
+
+
+	pci_clock_selection = pci_clock_selection & FPGA_REG16_PCI0_CLK_MASK;
+
+	switch (pci_clock_selection) {
+		case FPGA_REG16_PCI0_CLK_133_33:
+			pci_period = PERIOD_133_33MHZ;
+			break;
+		case FPGA_REG16_PCI0_CLK_100:
+			pci_period = PERIOD_100_00MHZ;
+			break;
+		case FPGA_REG16_PCI0_CLK_66_66:
+			pci_period = PERIOD_66_66MHZ;
+			break;
+		default:
+			pci_period = PERIOD_33_33MHZ;;
+			break;
+	}
+
+	return(pci_period);
 }
 #endif
 
diff --git a/cpu/ppc4xx/start.S b/cpu/ppc4xx/start.S
index 48b430d14d..c1e787f680 100644
--- a/cpu/ppc4xx/start.S
+++ b/cpu/ppc4xx/start.S
@@ -155,6 +155,11 @@
 
 /**************************************************************************/
 _start_440:
+	/*----------------------------------------------------------------+
+	| Core bug fix.  Clear the esr
+	+-----------------------------------------------------------------*/
+        addi	r0,r0,0x0000
+        mtspr	esr,r0
 	/*----------------------------------------------------------------*/
 	/* Clear and set up some registers. */
 	/*----------------------------------------------------------------*/
@@ -166,7 +171,7 @@ _start_440:
 	mtspr	srr1,r0
 	mtspr	csrr0,r0
 	mtspr	csrr1,r0
-#if defined(CONFIG_440GX) || defined(CONFIG_440SP) /* NOTE: 440GX adds machine check status regs */
+#if defined(CONFIG_440GX) || defined(CONFIG_440SP) || defined(CONFIG_440SPE)  /* NOTE: 440GX adds machine check status regs */
 	mtspr	mcsrr0,r0
 	mtspr	mcsrr1,r0
 	mfspr	r1, mcsr
@@ -200,6 +205,33 @@ _start_440:
 	ori	r1,r1,0x6000	/* cache touch */
 	mtspr	ccr0,r1
 
+#if defined (CONFIG_440SPE)
+	/*----------------------------------------------------------------+
+	| Initialize Core Configuration Reg1.
+	| a. ICDPEI: Record even parity. Normal operation.
+	| b. ICTPEI: Record even parity. Normal operation.
+	| c. DCTPEI: Record even parity. Normal operation.
+	| d. DCDPEI: Record even parity. Normal operation.
+	| e. DCUPEI: Record even parity. Normal operation.
+	| f. DCMPEI: Record even parity. Normal operation.
+	| g. FCOM:   Normal operation
+	| h. MMUPEI: Record even parity. Normal operation.
+	| i. FFF:    Flush only as much data as necessary.
+	| j. TCS:    Timebase increments from externally supplied clock
+	+-----------------------------------------------------------------*/
+	addis	r0, r0, 0x0000
+	ori	r0, r0, 0x0080
+	mtspr	ccr1, r0
+
+	/*----------------------------------------------------------------+
+	| Reset the timebase.
+	| The previous write to CCR1 sets the timebase source.
+	+-----------------------------------------------------------------*/
+	addi	r0, r0, 0x0000
+	mtspr	tbl, r0
+	mtspr	tbu, r0
+#endif
+
 	/*----------------------------------------------------------------*/
 	/* Setup interrupt vectors */
 	/*----------------------------------------------------------------*/
@@ -261,15 +293,26 @@ _start_440:
 	mtspr	ivlim,r1
 	mtspr	dvlim,r1
 
+	/*----------------------------------------------------------------+
+	|Initialize MMUCR[STID] = 0.
+	+-----------------------------------------------------------------*/
+	mfspr	r0,mmucr
+	addis	r1,0,0xFFFF
+	ori	r1,r1,0xFF00
+	and	r0,r0,r1
+	mtspr	mmucr,r0
+
 	/*----------------------------------------------------------------*/
 	/* Clear all TLB entries -- TID = 0, TS = 0 */
 	/*----------------------------------------------------------------*/
-	mtspr	mmucr,r0
+	addis	r0,0,0x0000
 	li	r1,0x003f	/* 64 TLB entries */
 	mtctr	r1
-0:	tlbwe	r0,r1,0x0000	/* Invalidate all entries (V=0)*/
+rsttlb:	tlbwe	r0,r1,0x0000	/* Invalidate all entries (V=0)*/
+	tlbwe	r0,r1,0x0001
+	tlbwe	r0,r1,0x0002
 	subi	r1,r1,0x0001
-	bdnz	0b
+	bdnz	rsttlb
 
 	/*----------------------------------------------------------------*/
 	/* TLB entry setup -- step thru tlbtab */
@@ -340,7 +383,7 @@ _start:
 	mtspr	tcr,r0			/* disable all */
 	mtspr	esr,r0			/* clear exception syndrome register */
 	mtxer	r0			/* clear integer exception register */
-#if !defined(CONFIG_440GX)
+#if !defined(CONFIG_440GX) && !defined(CONFIG_440SPE)
 	lis	r1,0x0002		/* set CE bit (Critical Exceptions) */
 	ori	r1,r1,0x1000		/* set ME bit (Machine Exceptions) */
 	mtmsr	r1			/* change MSR */
@@ -394,7 +437,7 @@ __440gx_msr_continue:
 	addi	r3,r3,32
 	bdnz	..d_ag
 #else
-#if defined (CONFIG_440GX) || defined(CONFIG_440SP)
+#if defined (CONFIG_440GX) || defined(CONFIG_440SP) || defined(CONFIG_440SPE)
 	mtdcr	l2_cache_cfg,r0		/* Ensure L2 Cache is off */
 #endif
 	mtdcr	isram0_sb1cr,r0		/* Disable bank 1 */
@@ -421,6 +464,19 @@ __440gx_msr_continue:
 	lis	r1, 0x8003
 	ori	r1,r1, 0x0980		/* fourth 64k */
 	mtdcr	isram0_sb3cr,r1
+#elif defined(CONFIG_440SPE)
+	lis	r1,0x0000		/* BAS = 0000_0000 */
+	ori	r1,r1,0x0984		/* first 64k */
+	mtdcr	isram0_sb0cr,r1
+	lis	r1,0x0001
+	ori	r1,r1,0x0984		/* second 64k */
+	mtdcr	isram0_sb1cr,r1
+	lis	r1, 0x0002
+	ori	r1,r1, 0x0984		/* third 64k */
+	mtdcr	isram0_sb2cr,r1
+	lis	r1, 0x0003
+	ori	r1,r1, 0x0984		/* fourth 64k */
+	mtdcr	isram0_sb3cr,r1
 #else
 	ori	r1,r1,0x0380		/* 8k rw */
 	mtdcr	isram0_sb0cr,r1
@@ -1220,7 +1276,7 @@ ppcSync:
  */
 	.globl	relocate_code
 relocate_code:
-#if defined(CONFIG_440EP) || defined(CONFIG_440GR)
+#if defined(CONFIG_440EP) || defined(CONFIG_440GR) || defined(CONFIG_440SPE)
 	dccci	0,0			    /* Invalidate data cache, now no longer our stack */
 	sync
 	addi	r1,r0,0x0000		/* TLB entry #0 */
diff --git a/cpu/ppc4xx/vecnum.h b/cpu/ppc4xx/vecnum.h
index cbfe41db9c..93cef026a3 100644
--- a/cpu/ppc4xx/vecnum.h
+++ b/cpu/ppc4xx/vecnum.h
@@ -31,7 +31,48 @@
 #ifndef _VECNUMS_H_
 #define _VECNUMS_H_
 
-#if defined(CONFIG_440SP)
+#if defined(CONFIG_440SPE)
+/* UIC 0 */
+#define VECNUM_U0           0           /* UART0                        */
+#define VECNUM_U1           1           /* UART1                        */
+#define VECNUM_IIC0         2           /* IIC0                         */
+#define VECNUM_IIC1         3           /* IIC1                         */
+#define VECNUM_PIM          4           /* PCI inbound message          */
+#define VECNUM_PCRW         5           /* PCI command reg write        */
+#define VECNUM_PPM          6           /* PCI power management         */
+#define VECNUM_MSI0         7           /* PCI MSI level 0              */
+#define VECNUM_MSI1         8           /* PCI MSI level 0              */
+#define VECNUM_MSI2         9           /* PCI MSI level 0              */
+#define VECNUM_D0           12          /* DMA channel 0                */
+#define VECNUM_D1           13          /* DMA channel 1                */
+#define VECNUM_D2           14          /* DMA channel 2                */
+#define VECNUM_D3           15          /* DMA channel 3                */
+#define VECNUM_UIC1NC       30          /* UIC1 non-critical interrupt  */
+#define VECNUM_UIC1C        31          /* UIC1 critical interrupt      */
+
+/* UIC 1 */
+#define VECNUM_MS           (32 + 1 )   /* MAL SERR                     */
+#define VECNUM_TXDE         (32 + 2 )   /* MAL TXDE                     */
+#define VECNUM_RXDE         (32 + 3 )   /* MAL RXDE                     */
+#define VECNUM_MTE          (32 + 6 )   /* MAL Tx EOB                   */
+#define VECNUM_MRE          (32 + 7 )   /* MAL Rx EOB                   */
+#define VECNUM_CT0          (32 + 12 )  /* GPT compare timer 0          */
+#define VECNUM_CT1          (32 + 13 )  /* GPT compare timer 1          */
+#define VECNUM_CT2          (32 + 14 )  /* GPT compare timer 2          */
+#define VECNUM_CT3          (32 + 15 )  /* GPT compare timer 3          */
+#define VECNUM_CT4          (32 + 16 )  /* GPT compare timer 4          */
+#define VECNUM_ETH0         (32 + 28)   /* Ethernet interrupt status    */
+#define VECNUM_EWU0         (32 + 29)   /* Emac  wakeup                 */
+
+/* UIC 2 */
+#define VECNUM_EIR5         (62 + 24)   /* External interrupt 5         */
+#define VECNUM_EIR4         (62 + 25)   /* External interrupt 4         */
+#define VECNUM_EIR3         (62 + 26)   /* External interrupt 3         */
+#define VECNUM_EIR2         (62 + 27)   /* External interrupt 2         */
+#define VECNUM_EIR1         (62 + 28)   /* External interrupt 1         */
+#define VECNUM_EIR0         (62 + 29)   /* External interrupt 0         */
+
+#elif defined(CONFIG_440SP)
 
 /* UIC 0 */
 #define VECNUM_U0           0           /* UART0                        */