m25p80: re-import it againt mtd_add_host

so we now create the cdev via mtd

This will also simplify sync with linux

to avoid the m25p8000 or m25p00 the cdev is still named name m25p and the
drivers m25p80

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

1 files changed, 937 insertions, 0 deletions

diff --git a/drivers/mtd/devices/m25p80.c b/drivers/mtd/devices/m25p80.c
new file mode 100644
index 0000000000..b4ac0459e4
--- /dev/null
+++ b/drivers/mtd/devices/m25p80.c
@@ -0,0 +1,937 @@
+/*
+ * MTD SPI driver for ST M25Pxx (and similar) serial flash chips
+ *
+ * Author: Mike Lavender, mike@steroidmicros.com
+ * Copyright (c) 2005, Intec Automation Inc.
+ *
+ * Some parts are based on lart.c by Abraham Van Der Merwe
+ *
+ * Cleaned up and generalized based on mtd_dataflash.c
+ *
+ * This code is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <common.h>
+#include <init.h>
+#include <driver.h>
+#include <spi/spi.h>
+#include <spi/flash.h>
+#include <xfuncs.h>
+#include <malloc.h>
+#include <errno.h>
+#include <linux/err.h>
+#include <clock.h>
+#include <linux/math64.h>
+#include <linux/mtd/cfi.h>
+#include <linux/mtd/mtd.h>
+
+/* Flash opcodes. */
+#define	OPCODE_WREN		0x06	/* Write enable */
+#define	OPCODE_RDSR		0x05	/* Read status register */
+#define	OPCODE_WRSR		0x01	/* Write status register 1 byte */
+#define	OPCODE_NORM_READ	0x03	/* Read data bytes (low frequency) */
+#define	OPCODE_FAST_READ	0x0b	/* Read data bytes (high frequency) */
+#define	OPCODE_PP		0x02	/* Page program (up to 256 bytes) */
+#define	OPCODE_BE_4K		0x20	/* Erase 4KiB block */
+#define	OPCODE_BE_32K		0x52	/* Erase 32KiB block */
+#define	OPCODE_CHIP_ERASE	0xc7	/* Erase whole flash chip */
+#define	OPCODE_SE		0xd8	/* Sector erase (usually 64KiB) */
+#define	OPCODE_RDID		0x9f	/* Read JEDEC ID */
+
+/* Used for SST flashes only. */
+#define	OPCODE_BP		0x02	/* Byte program */
+#define	OPCODE_WRDI		0x04	/* Write disable */
+#define	OPCODE_AAI_WP		0xad	/* Auto address increment word program */
+
+/* Used for Macronix flashes only. */
+#define	OPCODE_EN4B		0xb7	/* Enter 4-byte mode */
+#define	OPCODE_EX4B		0xe9	/* Exit 4-byte mode */
+
+/* Used for Spansion flashes only. */
+#define	OPCODE_BRWR		0x17	/* Bank register write */
+
+/* Status Register bits. */
+#define	SR_WIP			1	/* Write in progress */
+#define	SR_WEL			2	/* Write enable latch */
+/* meaning of other SR_* bits may differ between vendors */
+#define	SR_BP0			4	/* Block protect 0 */
+#define	SR_BP1			8	/* Block protect 1 */
+#define	SR_BP2			0x10	/* Block protect 2 */
+#define	SR_SRWD			0x80	/* SR write protect */
+
+/* Define max times to check status register before we give up. */
+#define	MAX_READY_WAIT		40	/* M25P16 specs 40s max chip erase */
+#define MAX_CMD_SIZE		6
+
+#define JEDEC_MFR(_jedec_id)	((_jedec_id) >> 16)
+
+/****************************************************************************/
+
+#define SPI_NAME_SIZE   32
+
+struct spi_device_id {
+	char name[SPI_NAME_SIZE];
+	unsigned long driver_data;
+};
+
+struct m25p {
+	struct spi_device	*spi;
+	struct mtd_info		mtd;
+	u16			page_size;
+	unsigned		sector_size;
+	u16			addr_width;
+	u8			erase_opcode;
+	u8			erase_opcode_4k;
+	u8			*command;
+};
+
+static inline struct m25p *mtd_to_m25p(struct mtd_info *mtd)
+{
+	return container_of(mtd, struct m25p, mtd);
+}
+
+/****************************************************************************/
+
+/*
+ * Internal helper functions
+ */
+
+/*
+ * Read the status register, returning its value in the location
+ * Return the status register value.
+ * Returns negative if error occurred.
+ */
+static int read_sr(struct m25p *flash)
+{
+	ssize_t retval;
+	u8 code = OPCODE_RDSR;
+	u8 val;
+
+	retval = spi_write_then_read(flash->spi, &code, 1, &val, 1);
+
+	if (retval < 0) {
+		dev_err(&flash->spi->dev, "error %d reading SR\n",
+				(int) retval);
+		return retval;
+	}
+
+	return val;
+}
+
+/*
+ * Write status register 1 byte
+ * Returns negative if error occurred.
+ */
+static int write_sr(struct m25p *flash, u8 val)
+{
+	flash->command[0] = OPCODE_WRSR;
+	flash->command[1] = val;
+
+	return spi_write(flash->spi, flash->command, 2);
+}
+
+/*
+ * Set write enable latch with Write Enable command.
+ * Returns negative if error occurred.
+ */
+static inline int write_enable(struct m25p *flash)
+{
+	u8	code = OPCODE_WREN;
+
+	return spi_write_then_read(flash->spi, &code, 1, NULL, 0);
+}
+
+/*
+ * Send write disble instruction to the chip.
+ */
+static inline int write_disable(struct m25p *flash)
+{
+	u8	code = OPCODE_WRDI;
+
+	return spi_write_then_read(flash->spi, &code, 1, NULL, 0);
+}
+
+/*
+ * Enable/disable 4-byte addressing mode.
+ */
+static inline int set_4byte(struct m25p *flash, u32 jedec_id, int enable)
+{
+	switch (JEDEC_MFR(jedec_id)) {
+	case CFI_MFR_MACRONIX:
+		flash->command[0] = enable ? OPCODE_EN4B : OPCODE_EX4B;
+		return spi_write(flash->spi, flash->command, 1);
+	default:
+		/* Spansion style */
+		flash->command[0] = OPCODE_BRWR;
+		flash->command[1] = enable << 7;
+		return spi_write(flash->spi, flash->command, 2);
+	}
+}
+
+/*
+ * Service routine to read status register until ready, or timeout occurs.
+ * Returns non-zero if error.
+ */
+static int wait_till_ready(struct m25p *flash)
+{
+	int sr;
+	uint64_t timer_start;
+
+	timer_start = get_time_ns();
+
+	do {
+		if ((sr = read_sr(flash)) < 0)
+			break;
+		else if (!(sr & SR_WIP))
+			return 0;
+
+	} while (!(is_timeout(timer_start, MAX_READY_WAIT * SECOND)));
+
+	return -ETIMEDOUT;
+}
+
+/*
+ * Erase the whole flash memory
+ *
+ * Returns 0 if successful, non-zero otherwise.
+ */
+static int erase_chip(struct m25p *flash)
+{
+	dev_dbg(&flash->spi->dev, "%s %lldKiB\n",
+		__func__, (long long)(flash->mtd.size >> 10));
+
+	/* Wait until finished previous write command. */
+	if (wait_till_ready(flash))
+		return -ETIMEDOUT;
+
+	/* Send write enable, then erase commands. */
+	write_enable(flash);
+
+	/* Set up command buffer. */
+	flash->command[0] = OPCODE_CHIP_ERASE;
+
+	spi_write(flash->spi, flash->command, 1);
+
+	return 0;
+}
+
+static void m25p_addr2cmd(struct m25p *flash, unsigned int addr, u8 *cmd)
+{
+	/* opcode is in cmd[0] */
+	cmd[1] = addr >> (flash->addr_width * 8 -  8);
+	cmd[2] = addr >> (flash->addr_width * 8 - 16);
+	cmd[3] = addr >> (flash->addr_width * 8 - 24);
+	cmd[4] = addr >> (flash->addr_width * 8 - 32);
+}
+
+static int m25p_cmdsz(struct m25p *flash)
+{
+	return 1 + flash->addr_width;
+}
+
+/*
+ * Erase one sector of flash memory at offset ``offset'' which is any
+ * address within the sector which should be erased.
+ *
+ * Returns 0 if successful, non-zero otherwise.
+ */
+static int erase_sector(struct m25p *flash, u32 offset, u32 command)
+{
+	dev_dbg(&flash->spi->dev, "%s %dKiB at 0x%08x\n",
+		__func__, flash->mtd.erasesize / 1024, offset);
+
+	/* Wait until finished previous write command. */
+	if (wait_till_ready(flash))
+		return -ETIMEDOUT;
+
+	/* Send write enable, then erase commands. */
+	write_enable(flash);
+
+	/* Set up command buffer. */
+	flash->command[0] = command;
+	m25p_addr2cmd(flash, offset, flash->command);
+
+	spi_write(flash->spi, flash->command, m25p_cmdsz(flash));
+
+	return 0;
+}
+
+/****************************************************************************/
+
+/*
+ * MTD implementation
+ */
+
+/*
+ * Erase an address range on the flash chip.  The address range may extend
+ * one or more erase sectors.  Return an error is there is a problem erasing.
+ */
+static int m25p80_erase(struct mtd_info *mtd, struct erase_info *instr)
+{
+	struct m25p *flash = mtd_to_m25p(mtd);
+	u32 addr, len;
+	uint32_t rem;
+
+	dev_dbg(&flash->spi->dev, "%s at 0x%llx, len %lld\n",
+			__func__, (long long)instr->addr,
+			(long long)instr->len);
+
+	div_u64_rem(instr->len, mtd->erasesize, &rem);
+	if (rem)
+		return -EINVAL;
+
+	addr = instr->addr;
+	len = instr->len;
+
+	/* whole-chip erase? */
+	if (len == flash->mtd.size) {
+		if (erase_chip(flash)) {
+			instr->state = MTD_ERASE_FAILED;
+			return -EIO;
+		}
+		return 0;
+	}
+
+	if (flash->erase_opcode_4k) {
+		while (len && (addr & (flash->sector_size - 1))) {
+			if (ctrlc())
+				return -EINTR;
+			if (erase_sector(flash, addr, flash->erase_opcode_4k))
+				return -EIO;
+			addr += mtd->erasesize;
+			len -= mtd->erasesize;
+		}
+
+		while (len >= flash->sector_size) {
+			if (ctrlc())
+				return -EINTR;
+			if (erase_sector(flash, addr, flash->erase_opcode))
+				return -EIO;
+			addr += flash->sector_size;
+			len -= flash->sector_size;
+		}
+
+		while (len) {
+			if (ctrlc())
+				return -EINTR;
+			if (erase_sector(flash, addr, flash->erase_opcode_4k))
+				return -EIO;
+			addr += mtd->erasesize;
+			len -= mtd->erasesize;
+		}
+	} else {
+		while (len) {
+			if (ctrlc())
+				return -EINTR;
+			if (erase_sector(flash, addr, flash->erase_opcode))
+				return -EIO;
+
+			if (len <= mtd->erasesize)
+				break;
+			addr += mtd->erasesize;
+			len -= mtd->erasesize;
+		}
+	}
+
+	if (wait_till_ready(flash))
+		return -ETIMEDOUT;
+
+	instr->state = MTD_ERASE_DONE;
+	mtd_erase_callback(instr);
+
+	return 0;
+}
+
+/*
+ * Read an address range from the flash chip.  The address range
+ * may be any size provided it is within the physical boundaries.
+ */
+static int m25p80_read(struct mtd_info *mtd, loff_t from, size_t len,
+	size_t *retlen, u_char *buf)
+{
+	struct m25p *flash = mtd_to_m25p(mtd);
+	struct spi_transfer t[2];
+	struct spi_message m;
+	int fast_read = 0;
+
+	if (flash->spi->max_speed_hz >= 25000000)
+		fast_read = 1;
+
+	spi_message_init(&m);
+	memset(t, 0, (sizeof t));
+
+	/* NOTE:
+	 * OPCODE_FAST_READ (if available) is faster.
+	 * Should add 1 byte DUMMY_BYTE.
+	 */
+	t[0].tx_buf = flash->command;
+	t[0].len = m25p_cmdsz(flash) + fast_read;
+	spi_message_add_tail(&t[0], &m);
+
+	t[1].rx_buf = buf;
+	t[1].len = len;
+	spi_message_add_tail(&t[1], &m);
+
+	/* Wait till previous write/erase is done. */
+	if (wait_till_ready(flash))
+		return -ETIMEDOUT;
+
+	/* FIXME switch to OPCODE_FAST_READ.  It's required for higher
+	 * clocks; and at this writing, every chip this driver handles
+	 * supports that opcode.
+	 */
+
+	/* Set up the write data buffer. */
+	flash->command[0] = fast_read ? OPCODE_FAST_READ : OPCODE_NORM_READ;
+	m25p_addr2cmd(flash, from, flash->command);
+
+	spi_sync(flash->spi, &m);
+
+	*retlen = m.actual_length - m25p_cmdsz(flash) - fast_read;
+
+	return 0;
+}
+
+/*
+ * Write an address range to the flash chip.  Data must be written in
+ * FLASH_PAGESIZE chunks.  The address range may be any size provided
+ * it is within the physical boundaries.
+ */
+static int m25p80_write(struct mtd_info *mtd, loff_t to, size_t len,
+	size_t *retlen, const u_char *buf)
+{
+	struct m25p *flash = mtd_to_m25p(mtd);
+	u32 page_offset, page_size;
+	struct spi_transfer t[2];
+	struct spi_message m;
+
+	debug("m25p80_write %ld bytes at 0x%08lX\n", (unsigned long)count, offset);
+
+	spi_message_init(&m);
+	memset(t, 0, (sizeof t));
+
+	t[0].tx_buf = flash->command;
+	t[0].len = m25p_cmdsz(flash);
+	spi_message_add_tail(&t[0], &m);
+
+	t[1].tx_buf = buf;
+	spi_message_add_tail(&t[1], &m);
+
+	/* Wait until finished previous write command. */
+	if (wait_till_ready(flash))
+		return -ETIMEDOUT;
+
+	write_enable(flash);
+
+	/* Set up the opcode in the write buffer. */
+	flash->command[0] = OPCODE_PP;
+	m25p_addr2cmd(flash, to, flash->command);
+
+	page_offset = to & (flash->page_size - 1);
+
+	/* do all the bytes fit onto one page? */
+	if (page_offset + len <= flash->page_size) {
+		t[1].len = len;
+
+		spi_sync(flash->spi, &m);
+
+		*retlen = m.actual_length - m25p_cmdsz(flash);
+	} else {
+		u32 i;
+
+		/* the size of data remaining on the first page */
+		page_size = flash->page_size - page_offset;
+
+		t[1].len = page_size;
+		spi_sync(flash->spi, &m);
+
+		*retlen = m.actual_length - m25p_cmdsz(flash);
+
+		/* write everything in flash->page_size chunks */
+		for (i = page_size; i < len; i += page_size) {
+			page_size = len - i;
+			if (page_size > flash->page_size)
+				page_size = flash->page_size;
+
+			/* write the next page to flash */
+			m25p_addr2cmd(flash, to + i, flash->command);
+
+			t[1].tx_buf = buf + i;
+			t[1].len = page_size;
+
+			wait_till_ready(flash);
+
+			write_enable(flash);
+
+			spi_sync(flash->spi, &m);
+
+			*retlen += m.actual_length - m25p_cmdsz(flash);
+		}
+	}
+
+	return 0;
+}
+
+static int sst_write(struct mtd_info *mtd, loff_t to, size_t len,
+		size_t *retlen, const u_char *buf)
+{
+	struct m25p *flash = mtd_to_m25p(mtd);
+	struct spi_transfer t[2];
+	struct spi_message m;
+	size_t actual;
+	int cmd_sz, ret;
+
+	pr_debug("%s: %s to 0x%08x, len %zd\n", dev_name(&flash->spi->dev),
+			__func__, (u32)to, len);
+
+	spi_message_init(&m);
+	memset(t, 0, (sizeof t));
+
+	t[0].tx_buf = flash->command;
+	t[0].len = m25p_cmdsz(flash);
+	spi_message_add_tail(&t[0], &m);
+
+	t[1].tx_buf = buf;
+	spi_message_add_tail(&t[1], &m);
+
+	/* Wait until finished previous write command. */
+	ret = wait_till_ready(flash);
+	if (ret)
+		goto time_out;
+
+	write_enable(flash);
+
+	actual = to % 2;
+	/* Start write from odd address. */
+	if (actual) {
+		flash->command[0] = OPCODE_BP;
+		m25p_addr2cmd(flash, to, flash->command);
+
+		/* write one byte. */
+		t[1].len = 1;
+		spi_sync(flash->spi, &m);
+		ret = wait_till_ready(flash);
+		if (ret)
+			goto time_out;
+		*retlen += m.actual_length - m25p_cmdsz(flash);
+	}
+	to += actual;
+
+	flash->command[0] = OPCODE_AAI_WP;
+	m25p_addr2cmd(flash, to, flash->command);
+
+	/* Write out most of the data here. */
+	cmd_sz = m25p_cmdsz(flash);
+	for (; actual < len - 1; actual += 2) {
+		t[0].len = cmd_sz;
+		/* write two bytes. */
+		t[1].len = 2;
+		t[1].tx_buf = buf + actual;
+
+		spi_sync(flash->spi, &m);
+		ret = wait_till_ready(flash);
+		if (ret)
+			goto time_out;
+		*retlen += m.actual_length - cmd_sz;
+		cmd_sz = 1;
+		to += 2;
+	}
+	write_disable(flash);
+	ret = wait_till_ready(flash);
+	if (ret)
+		goto time_out;
+
+	/* Write out trailing byte if it exists. */
+	if (actual != len) {
+		write_enable(flash);
+		flash->command[0] = OPCODE_BP;
+		m25p_addr2cmd(flash, to, flash->command);
+		t[0].len = m25p_cmdsz(flash);
+		t[1].len = 1;
+		t[1].tx_buf = buf + actual;
+
+		spi_sync(flash->spi, &m);
+		ret = wait_till_ready(flash);
+		if (ret)
+			goto time_out;
+		*retlen += m.actual_length - m25p_cmdsz(flash);
+		write_disable(flash);
+	}
+
+time_out:
+	return ret;
+}
+
+/****************************************************************************/
+
+/*
+ * SPI device driver setup and teardown
+ */
+
+struct flash_info {
+	/* JEDEC id zero means "no ID" (most older chips); otherwise it has
+	 * a high byte of zero plus three data bytes: the manufacturer id,
+	 * then a two byte device id.
+	 */
+	u32		jedec_id;
+	u16             ext_id;
+
+	/* The size listed here is what works with OPCODE_SE, which isn't
+	 * necessarily called a "sector" by the vendor.
+	 */
+	unsigned	sector_size;
+	u16		n_sectors;
+
+	u16		page_size;
+	u16		addr_width;
+
+	u16		flags;
+#define	SECT_4K		0x01		/* OPCODE_BE_4K works uniformly */
+#define	M25P_NO_ERASE	0x02		/* No erase command needed */
+};
+
+#define INFO(_jedec_id, _ext_id, _sector_size, _n_sectors, _flags)	\
+	((unsigned long)&(struct flash_info) {				\
+		.jedec_id = (_jedec_id),				\
+		.ext_id = (_ext_id),					\
+		.sector_size = (_sector_size),				\
+		.n_sectors = (_n_sectors),				\
+		.page_size = 256,					\
+		.flags = (_flags),					\
+	})
+
+#define CAT25_INFO(_sector_size, _n_sectors, _page_size, _addr_width)	\
+	((unsigned long)&(struct flash_info) {				\
+		.sector_size = (_sector_size),				\
+		.n_sectors = (_n_sectors),				\
+		.page_size = (_page_size),				\
+		.addr_width = (_addr_width),				\
+		.flags = M25P_NO_ERASE,					\
+	})
+
+/* NOTE: double check command sets and memory organization when you add
+ * more flash chips.  This current list focusses on newer chips, which
+ * have been converging on command sets which including JEDEC ID.
+ */
+static const struct spi_device_id m25p_ids[] = {
+	/* Atmel -- some are (confusingly) marketed as "DataFlash" */
+	{ "at25fs010",  INFO(0x1f6601, 0, 32 * 1024,   4, SECT_4K) },
+	{ "at25fs040",  INFO(0x1f6604, 0, 64 * 1024,   8, SECT_4K) },
+
+	{ "at25df041a", INFO(0x1f4401, 0, 64 * 1024,   8, SECT_4K) },
+	{ "at25df641",  INFO(0x1f4800, 0, 64 * 1024, 128, SECT_4K) },
+
+	{ "at26f004",   INFO(0x1f0400, 0, 64 * 1024,  8, SECT_4K) },
+	{ "at26df081a", INFO(0x1f4501, 0, 64 * 1024, 16, SECT_4K) },
+	{ "at26df161a", INFO(0x1f4601, 0, 64 * 1024, 32, SECT_4K) },
+	{ "at26df321",  INFO(0x1f4700, 0, 64 * 1024, 64, SECT_4K) },
+
+	/* EON -- en25xxx */
+	{ "en25f32", INFO(0x1c3116, 0, 64 * 1024,  64, SECT_4K) },
+	{ "en25p32", INFO(0x1c2016, 0, 64 * 1024,  64, 0) },
+	{ "en25p64", INFO(0x1c2017, 0, 64 * 1024, 128, 0) },
+
+	/* Intel/Numonyx -- xxxs33b */
+	{ "160s33b",  INFO(0x898911, 0, 64 * 1024,  32, 0) },
+	{ "320s33b",  INFO(0x898912, 0, 64 * 1024,  64, 0) },
+	{ "640s33b",  INFO(0x898913, 0, 64 * 1024, 128, 0) },
+
+	/* Macronix */
+	{ "mx25l4005a",  INFO(0xc22013, 0, 64 * 1024,   8, SECT_4K) },
+	{ "mx25l8005",   INFO(0xc22014, 0, 64 * 1024,  16, 0) },
+	{ "mx25l3205d",  INFO(0xc22016, 0, 64 * 1024,  64, 0) },
+	{ "mx25l6405d",  INFO(0xc22017, 0, 64 * 1024, 128, 0) },
+	{ "mx25l12805d", INFO(0xc22018, 0, 64 * 1024, 256, 0) },
+	{ "mx25l12855e", INFO(0xc22618, 0, 64 * 1024, 256, 0) },
+	{ "mx25l25635e", INFO(0xc22019, 0, 64 * 1024, 512, 0) },
+	{ "mx25l25655e", INFO(0xc22619, 0, 64 * 1024, 512, 0) },
+
+	/* Spansion -- single (large) sector size only, at least
+	 * for the chips listed here (without boot sectors).
+	 */
+	{ "s25sl004a",  INFO(0x010212,      0,  64 * 1024,   8, 0) },
+	{ "s25sl008a",  INFO(0x010213,      0,  64 * 1024,  16, 0) },
+	{ "s25sl016a",  INFO(0x010214,      0,  64 * 1024,  32, 0) },
+	{ "s25sl032a",  INFO(0x010215,      0,  64 * 1024,  64, 0) },
+	{ "s25sl032p",  INFO(0x010215, 0x4d00,  64 * 1024,  64, SECT_4K) },
+	{ "s25sl064a",  INFO(0x010216,      0,  64 * 1024, 128, 0) },
+	{ "s25sl12800", INFO(0x012018, 0x0300, 256 * 1024,  64, 0) },
+	{ "s25sl12801", INFO(0x012018, 0x0301,  64 * 1024, 256, 0) },
+	{ "s25fl129p0", INFO(0x012018, 0x4d00, 256 * 1024,  64, 0) },
+	{ "s25fl129p1", INFO(0x012018, 0x4d01,  64 * 1024, 256, 0) },
+	{ "s25fl016k",  INFO(0xef4015,      0,  64 * 1024,  32, SECT_4K) },
+	{ "s25fl064k",  INFO(0xef4017,      0,  64 * 1024, 128, SECT_4K) },
+
+	/* SST -- large erase sizes are "overlays", "sectors" are 4K */
+	{ "sst25vf040b", INFO(0xbf258d, 0, 64 * 1024,  8, SECT_4K) },
+	{ "sst25vf080b", INFO(0xbf258e, 0, 64 * 1024, 16, SECT_4K) },
+	{ "sst25vf016b", INFO(0xbf2541, 0, 64 * 1024, 32, SECT_4K) },
+	{ "sst25vf032b", INFO(0xbf254a, 0, 64 * 1024, 64, SECT_4K) },
+	{ "sst25wf512",  INFO(0xbf2501, 0, 64 * 1024,  1, SECT_4K) },
+	{ "sst25wf010",  INFO(0xbf2502, 0, 64 * 1024,  2, SECT_4K) },
+	{ "sst25wf020",  INFO(0xbf2503, 0, 64 * 1024,  4, SECT_4K) },
+	{ "sst25wf040",  INFO(0xbf2504, 0, 64 * 1024,  8, SECT_4K) },
+
+	/* ST Microelectronics -- newer production may have feature updates */
+	{ "m25p05",  INFO(0x202010,  0,  32 * 1024,   2, 0) },
+	{ "m25p10",  INFO(0x202011,  0,  32 * 1024,   4, 0) },
+	{ "m25p20",  INFO(0x202012,  0,  64 * 1024,   4, 0) },
+	{ "m25p40",  INFO(0x202013,  0,  64 * 1024,   8, 0) },
+	{ "m25p80",  INFO(0x202014,  0,  64 * 1024,  16, 0) },
+	{ "m25p16",  INFO(0x202015,  0,  64 * 1024,  32, 0) },
+	{ "m25p32",  INFO(0x202016,  0,  64 * 1024,  64, 0) },
+	{ "m25p64",  INFO(0x202017,  0,  64 * 1024, 128, 0) },
+	{ "m25p128", INFO(0x202018,  0, 256 * 1024,  64, 0) },
+
+	{ "m25p05-nonjedec",  INFO(0, 0,  32 * 1024,   2, 0) },
+	{ "m25p10-nonjedec",  INFO(0, 0,  32 * 1024,   4, 0) },
+	{ "m25p20-nonjedec",  INFO(0, 0,  64 * 1024,   4, 0) },
+	{ "m25p40-nonjedec",  INFO(0, 0,  64 * 1024,   8, 0) },
+	{ "m25p80-nonjedec",  INFO(0, 0,  64 * 1024,  16, 0) },
+	{ "m25p16-nonjedec",  INFO(0, 0,  64 * 1024,  32, 0) },
+	{ "m25p32-nonjedec",  INFO(0, 0,  64 * 1024,  64, 0) },
+	{ "m25p64-nonjedec",  INFO(0, 0,  64 * 1024, 128, 0) },
+	{ "m25p128-nonjedec", INFO(0, 0, 256 * 1024,  64, 0) },
+
+	{ "m45pe10", INFO(0x204011,  0, 64 * 1024,    2, 0) },
+	{ "m45pe80", INFO(0x204014,  0, 64 * 1024,   16, 0) },
+	{ "m45pe16", INFO(0x204015,  0, 64 * 1024,   32, 0) },
+
+	{ "m25pe80", INFO(0x208014,  0, 64 * 1024, 16,       0) },
+	{ "m25pe16", INFO(0x208015,  0, 64 * 1024, 32, SECT_4K) },
+
+	{ "m25px64", INFO(0x207117,  0, 64 * 1024, 128, 0) },
+
+	/* Winbond -- w25x "blocks" are 64K, "sectors" are 4KiB */
+	{ "w25x10", INFO(0xef3011, 0, 64 * 1024,  2,  SECT_4K) },
+	{ "w25x20", INFO(0xef3012, 0, 64 * 1024,  4,  SECT_4K) },
+	{ "w25x40", INFO(0xef3013, 0, 64 * 1024,  8,  SECT_4K) },
+	{ "w25x80", INFO(0xef3014, 0, 64 * 1024,  16, SECT_4K) },
+	{ "w25x16", INFO(0xef3015, 0, 64 * 1024,  32, SECT_4K) },
+	{ "w25x32", INFO(0xef3016, 0, 64 * 1024,  64, SECT_4K) },
+	{ "w25q32", INFO(0xef4016, 0, 64 * 1024,  64, SECT_4K) },
+	{ "w25x64", INFO(0xef3017, 0, 64 * 1024, 128, SECT_4K) },
+	{ "w25q64", INFO(0xef4017, 0, 64 * 1024, 128, SECT_4K) },
+
+	/* Catalyst / On Semiconductor -- non-JEDEC */
+	{ "cat25c11", CAT25_INFO(  16, 8, 16, 1) },
+	{ "cat25c03", CAT25_INFO(  32, 8, 16, 2) },
+	{ "cat25c09", CAT25_INFO( 128, 8, 32, 2) },
+	{ "cat25c17", CAT25_INFO( 256, 8, 32, 2) },
+	{ "cat25128", CAT25_INFO(2048, 8, 64, 2) },
+
+	/* Micron */
+	{ "n25q128", INFO(0x20ba18, 0, 64 * 1024, 256, 0) },
+	{ },
+};
+
+static const struct spi_device_id *jedec_probe(struct spi_device *spi)
+{
+	int			tmp;
+	u8			code = OPCODE_RDID;
+	u8			id[5];
+	u32			jedec;
+	u16			ext_jedec;
+	struct flash_info	*info;
+
+	/* JEDEC also defines an optional "extended device information"
+	 * string for after vendor-specific data, after the three bytes
+	 * we use here.  Supporting some chips might require using it.
+	 */
+	tmp = spi_write_then_read(spi, &code, 1, id, 5);
+	if (tmp < 0) {
+		pr_debug("%s: error %d reading JEDEC ID\n",
+				dev_name(&spi->dev), tmp);
+		return ERR_PTR(tmp);
+	}
+	jedec = id[0];
+	jedec = jedec << 8;
+	jedec |= id[1];
+	jedec = jedec << 8;
+	jedec |= id[2];
+
+	ext_jedec = id[3] << 8 | id[4];
+
+	for (tmp = 0; tmp < ARRAY_SIZE(m25p_ids) - 1; tmp++) {
+		info = (void *)m25p_ids[tmp].driver_data;
+		if (info->jedec_id == jedec) {
+			if (info->ext_id != 0 && info->ext_id != ext_jedec)
+				continue;
+			return &m25p_ids[tmp];
+		}
+	}
+	dev_err(&spi->dev, "unrecognized JEDEC id %06x\n", jedec);
+	return ERR_PTR(-ENODEV);
+}
+
+
+/*
+ * board specific setup should have ensured the SPI clock used here
+ * matches what the READ command supports, at least until this driver
+ * understands FAST_READ (for clocks over 25 MHz).
+ */
+static int m25p_probe(struct device_d *dev)
+{
+	struct spi_device *spi = (struct spi_device *)dev->type_data;
+	const struct spi_device_id	*id = NULL;
+	struct flash_platform_data	*data;
+	struct m25p			*flash;
+	struct flash_info		*info = NULL;
+	unsigned			i;
+	unsigned			do_jdec_probe = 1;
+
+	/* Platform data helps sort out which chip type we have, as
+	 * well as how this board partitions it.  If we don't have
+	 * a chip ID, try the JEDEC id commands; they'll work for most
+	 * newer chips, even if we don't recognize the particular chip.
+	 */
+	data = dev->platform_data;
+	if (data && data->type) {
+		const struct spi_device_id *plat_id;
+
+		for (i = 0; i < ARRAY_SIZE(m25p_ids) - 1; i++) {
+			plat_id = &m25p_ids[i];
+			if (strcmp(data->type, plat_id->name))
+				continue;
+			break;
+		}
+
+		if (i < ARRAY_SIZE(m25p_ids) - 1) {
+			id = plat_id;
+			info = (void *)id->driver_data;
+			/* If flash type is provided but the memory is not
+			 * JEDEC compliant, don't try to probe the JEDEC id */
+			if (!info->jedec_id)
+				do_jdec_probe = 0;
+		} else
+			dev_warn(&spi->dev, "unrecognized id %s\n", data->type);
+	}
+
+	if (do_jdec_probe) {
+		const struct spi_device_id *jid;
+
+		jid = jedec_probe(spi);
+		if (IS_ERR(jid)) {
+			return PTR_ERR(jid);
+		} else if (jid != id) {
+			/*
+			 * JEDEC knows better, so overwrite platform ID. We
+			 * can't trust partitions any longer, but we'll let
+			 * mtd apply them anyway, since some partitions may be
+			 * marked read-only, and we don't want to lose that
+			 * information, even if it's not 100% accurate.
+			 */
+			if (id)
+				dev_warn(dev, "found %s, expected %s\n",
+					jid->name, id->name);
+
+			id = jid;
+			info = (void *)jid->driver_data;
+		}
+	}
+
+	flash = xzalloc(sizeof *flash);
+	flash->command = xmalloc(MAX_CMD_SIZE);
+
+	flash->spi = spi;
+	dev->priv = (void *)flash;
+	/*
+	 * Atmel, SST and Intel/Numonyx serial flash tend to power
+	 * up with the software protection bits set
+	 */
+
+	if (JEDEC_MFR(info->jedec_id) == CFI_MFR_ATMEL ||
+	    JEDEC_MFR(info->jedec_id) == CFI_MFR_INTEL ||
+	    JEDEC_MFR(info->jedec_id) == CFI_MFR_SST) {
+		write_enable(flash);
+		write_sr(flash, 0);
+	}
+
+	if (data && data->name)
+		flash->mtd.name = data->name;
+	else
+		flash->mtd.name = "m25p";
+
+	flash->mtd.type = MTD_NORFLASH;
+	flash->mtd.writesize = 1;
+	flash->mtd.flags = MTD_CAP_NORFLASH;
+	flash->mtd.size = info->sector_size * info->n_sectors;
+	flash->mtd.erase = m25p80_erase;
+	flash->mtd.read = m25p80_read;
+
+	/* sst flash chips use AAI word program */
+	if (IS_ENABLED(CONFIG_MTD_SST25L) && JEDEC_MFR(info->jedec_id) == CFI_MFR_SST)
+		flash->mtd.write = sst_write;
+	else
+		flash->mtd.write = m25p80_write;
+
+	/* prefer "small sector" erase if possible */
+	if (info->flags & SECT_4K) {
+		flash->erase_opcode_4k = OPCODE_BE_4K;
+		flash->erase_opcode = OPCODE_SE;
+		flash->mtd.erasesize = 4096;
+	} else {
+		flash->erase_opcode = OPCODE_SE;
+		flash->mtd.erasesize = info->sector_size;
+	}
+
+	if (info->flags & M25P_NO_ERASE)
+		flash->mtd.flags |= MTD_NO_ERASE;
+
+	flash->mtd.parent = &spi->dev;
+	flash->page_size = info->page_size;
+	flash->sector_size = info->sector_size;
+
+	if (info->addr_width)
+		flash->addr_width = info->addr_width;
+	else {
+		/* enable 4-byte addressing if the device exceeds 16MiB */
+		if (flash->mtd.size > 0x1000000) {
+			flash->addr_width = 4;
+			set_4byte(flash, info->jedec_id, 1);
+		} else
+			flash->addr_width = 3;
+	}
+
+	dev_info(dev, "%s (%lld Kbytes)\n", id->name,
+			(long long)flash->mtd.size >> 10);
+
+	pr_debug("mtd .name = %s, .size = 0x%llx (%lldMiB) "
+			".erasesize = 0x%.8x (%uKiB) .numeraseregions = %d\n",
+		flash->mtd.name,
+		(long long)flash->mtd.size, (long long)(flash->mtd.size >> 20),
+		flash->mtd.erasesize, flash->mtd.erasesize / 1024,
+		flash->mtd.numeraseregions);
+
+	if (flash->mtd.numeraseregions)
+		for (i = 0; i < flash->mtd.numeraseregions; i++)
+			pr_debug("mtd.eraseregions[%d] = { .offset = 0x%llx, "
+				".erasesize = 0x%.8x (%uKiB), "
+				".numblocks = %d }\n",
+				i, (long long)flash->mtd.eraseregions[i].offset,
+				flash->mtd.eraseregions[i].erasesize,
+				flash->mtd.eraseregions[i].erasesize / 1024,
+				flash->mtd.eraseregions[i].numblocks);
+
+
+
+	return add_mtd_device(&flash->mtd, flash->mtd.name);
+}
+
+static struct driver_d m25p80_driver = {
+	.name	= "m25p80",
+	.probe	= m25p_probe,
+};
+
+static int m25p80_init(void)
+{
+	return spi_register_driver(&m25p80_driver);
+}
+device_initcall(m25p80_init);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Mike Lavender");
+MODULE_DESCRIPTION("MTD SPI driver for ST M25Pxx flash chips");