Add devicetree source files as of Linux-3.15-rc2

This adds the Linux dts files to barebox. The dts files are
generated from Ian Campbells device-tree-rebasing.git:

git://xenbits.xen.org/people/ianc/device-tree-rebasing.git

The dts are found in dts/ in the barebox repository and
will be updated from upstream regularly, probably for each upstream
-rc.

To keep the synchronization with upstream easy no changes to
the original files are allowed under dts/. Instead changes to
upstream dts files will be done using overlays in arch/$ARCH/dts/.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

6 files changed, 387 insertions, 0 deletions

diff --git a/dts/Bindings/c6x/clocks.txt b/dts/Bindings/c6x/clocks.txt
new file mode 100644
index 0000000000..a04f5fd301
--- /dev/null
+++ b/dts/Bindings/c6x/clocks.txt
@@ -0,0 +1,40 @@
+C6X PLL Clock Controllers
+-------------------------
+
+This is a first-cut support for the SoC clock controllers. This is still
+under development and will probably change as the common device tree
+clock support is added to the kernel.
+
+Required properties:
+
+- compatible: "ti,c64x+pll"
+    May also have SoC-specific value to support SoC-specific initialization
+    in the driver. One of:
+        "ti,c6455-pll"
+        "ti,c6457-pll"
+        "ti,c6472-pll"
+        "ti,c6474-pll"
+
+- reg: base address and size of register area
+- clock-frequency: input clock frequency in hz
+
+
+Optional properties:
+
+- ti,c64x+pll-bypass-delay: CPU cycles to delay when entering bypass mode
+
+- ti,c64x+pll-reset-delay:  CPU cycles to delay after PLL reset
+
+- ti,c64x+pll-lock-delay:   CPU cycles to delay after PLL frequency change
+
+Example:
+
+	clock-controller@29a0000 {
+		compatible = "ti,c6472-pll", "ti,c64x+pll";
+		reg = <0x029a0000 0x200>;
+		clock-frequency = <25000000>;
+
+		ti,c64x+pll-bypass-delay = <200>;
+		ti,c64x+pll-reset-delay = <12000>;
+		ti,c64x+pll-lock-delay = <80000>;
+	};
diff --git a/dts/Bindings/c6x/dscr.txt b/dts/Bindings/c6x/dscr.txt
new file mode 100644
index 0000000000..b0e97144cf
--- /dev/null
+++ b/dts/Bindings/c6x/dscr.txt
@@ -0,0 +1,127 @@
+Device State Configuration Registers
+------------------------------------
+
+TI C6X SoCs contain a region of miscellaneous registers which provide various
+function for SoC control or status. Details vary considerably among from SoC
+to SoC with no two being alike.
+
+In general, the Device State Configuration Registers (DSCR) will provide one or
+more configuration registers often protected by a lock register where one or
+more key values must be written to a lock register in order to unlock the
+configuration register for writes. These configuration register may be used to
+enable (and disable in some cases) SoC pin drivers, select peripheral clock
+sources (internal or pin), etc. In some cases, a configuration register is
+write once or the individual bits are write once. In addition to device config,
+the DSCR block may provide registers which which are used to reset peripherals,
+provide device ID information, provide ethernet MAC addresses, as well as other
+miscellaneous functions.
+
+For device state control (enable/disable), each device control is assigned an
+id which is used by individual device drivers to control the state as needed.
+
+Required properties:
+
+- compatible: must be "ti,c64x+dscr"
+- reg: register area base and size
+
+Optional properties:
+
+  NOTE: These are optional in that not all SoCs will have all properties. For
+        SoCs which do support a given property, leaving the property out of the
+        device tree will result in reduced functionality or possibly driver
+        failure.
+
+- ti,dscr-devstat
+    offset of the devstat register
+
+- ti,dscr-silicon-rev
+    offset, start bit, and bitsize of silicon revision field
+
+- ti,dscr-rmii-resets
+    offset and bitmask of RMII reset field. May have multiple tuples if more
+    than one ethernet port is available.
+
+- ti,dscr-locked-regs
+    possibly multiple tuples describing registers which are write protected by
+    a lock register. Each tuple consists of the register offset, lock register
+    offsset, and the key value used to unlock the register.
+
+- ti,dscr-kick-regs
+    offset and key values of two "kick" registers used to write protect other
+    registers in DSCR. On SoCs using kick registers, the first key must be
+    written to the first kick register and the second key must be written to
+    the second register before other registers in the area are write-enabled.
+
+- ti,dscr-mac-fuse-regs
+    MAC addresses are contained in two registers. Each element of a MAC address
+    is contained in a single byte. This property has two tuples. Each tuple has
+    a register offset and four cells representing bytes in the register from
+    most significant to least. The value of these four cells is the MAC byte
+    index (1-6) of the byte within the register. A value of 0 means the byte
+    is unused in the MAC address.
+
+- ti,dscr-devstate-ctl-regs
+    This property describes the bitfields used to control the state of devices.
+    Each tuple describes a range of identical bitfields used to control one or
+    more devices (one bitfield per device). The layout of each tuple is:
+
+        start_id num_ids reg enable disable start_bit nbits
+
+    Where:
+        start_id is device id for the first device control in the range
+        num_ids is the number of device controls in the range
+        reg is the offset of the register holding the control bits
+        enable is the value to enable a device
+        disable is the value to disable a device (0xffffffff if cannot disable)
+        start_bit is the bit number of the first bit in the range
+        nbits is the number of bits per device control
+
+- ti,dscr-devstate-stat-regs
+    This property describes the bitfields used to provide device state status
+    for device states controlled by the DSCR. Each tuple describes a range of
+    identical bitfields used to provide status for one or more devices (one
+    bitfield per device). The layout of each tuple is:
+
+        start_id num_ids reg enable disable start_bit nbits
+
+    Where:
+        start_id is device id for the first device status in the range
+        num_ids is the number of devices covered by the range
+        reg is the offset of the register holding the status bits
+        enable is the value indicating device is enabled
+        disable is the value indicating device is disabled
+        start_bit is the bit number of the first bit in the range
+        nbits is the number of bits per device status
+
+- ti,dscr-privperm
+    Offset and default value for register used to set access privilege for
+    some SoC devices.
+
+
+Example:
+
+	device-state-config-regs@2a80000 {
+		compatible = "ti,c64x+dscr";
+		reg = <0x02a80000 0x41000>;
+
+		ti,dscr-devstat = <0>;
+		ti,dscr-silicon-rev = <8 28 0xf>;
+		ti,dscr-rmii-resets = <0x40020 0x00040000>;
+
+		ti,dscr-locked-regs = <0x40008 0x40004 0x0f0a0b00>;
+		ti,dscr-devstate-ctl-regs =
+			 <0 12 0x40008 1 0  0  2
+			  12 1 0x40008 3 0 30  2
+			  13 2 0x4002c 1 0xffffffff 0 1>;
+		ti,dscr-devstate-stat-regs =
+			<0 10 0x40014 1 0  0  3
+			 10 2 0x40018 1 0  0  3>;
+
+		ti,dscr-mac-fuse-regs = <0x700 1 2 3 4
+					 0x704 5 6 0 0>;
+
+		ti,dscr-privperm = <0x41c 0xaaaaaaaa>;
+
+		ti,dscr-kick-regs = <0x38 0x83E70B13
+				     0x3c 0x95A4F1E0>;
+	};
diff --git a/dts/Bindings/c6x/emifa.txt b/dts/Bindings/c6x/emifa.txt
new file mode 100644
index 0000000000..0ff6e9b9a1
--- /dev/null
+++ b/dts/Bindings/c6x/emifa.txt
@@ -0,0 +1,62 @@
+External Memory Interface
+-------------------------
+
+The emifa node describes a simple external bus controller found on some C6X
+SoCs. This interface provides external busses with a number of chip selects.
+
+Required properties:
+
+- compatible: must be "ti,c64x+emifa", "simple-bus"
+- reg: register area base and size
+- #address-cells: must be 2 (chip-select + offset)
+- #size-cells: must be 1
+- ranges: mapping from EMIFA space to parent space
+
+
+Optional properties:
+
+- ti,dscr-dev-enable: Device ID if EMIF is enabled/disabled from DSCR
+
+- ti,emifa-burst-priority:
+      Number of memory transfers after which the EMIF will elevate the priority
+      of the oldest command in the command FIFO. Setting this field to 255
+      disables this feature, thereby allowing old commands to stay in the FIFO
+      indefinitely.
+
+- ti,emifa-ce-config:
+      Configuration values for each of the supported chip selects.
+
+Example:
+
+	emifa@70000000 {
+		compatible = "ti,c64x+emifa", "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <1>;
+		reg = <0x70000000 0x100>;
+		ranges = <0x2 0x0 0xa0000000 0x00000008
+		          0x3 0x0 0xb0000000 0x00400000
+			  0x4 0x0 0xc0000000 0x10000000
+			  0x5 0x0 0xD0000000 0x10000000>;
+
+		ti,dscr-dev-enable = <13>;
+		ti,emifa-burst-priority = <255>;
+		ti,emifa-ce-config = <0x00240120
+				      0x00240120
+				      0x00240122
+				      0x00240122>;
+
+		flash@3,0 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "cfi-flash";
+			reg = <0x3 0x0 0x400000>;
+			bank-width = <1>;
+			device-width = <1>;
+			partition@0 {
+				reg = <0x0 0x400000>;
+				label = "NOR";
+			};
+		};
+	};
+
+This shows a flash chip attached to chip select 3.
diff --git a/dts/Bindings/c6x/interrupt.txt b/dts/Bindings/c6x/interrupt.txt
new file mode 100644
index 0000000000..42bb796cc4
--- /dev/null
+++ b/dts/Bindings/c6x/interrupt.txt
@@ -0,0 +1,104 @@
+C6X Interrupt Chips
+-------------------
+
+* C64X+ Core Interrupt Controller
+
+  The core interrupt controller provides 16 prioritized interrupts to the
+  C64X+ core. Priority 0 and 1 are used for reset and NMI respectively.
+  Priority 2 and 3 are reserved. Priority 4-15 are used for interrupt
+  sources coming from outside the core.
+
+  Required properties:
+  --------------------
+  - compatible: Should be "ti,c64x+core-pic";
+  - #interrupt-cells: <1>
+
+  Interrupt Specifier Definition
+  ------------------------------
+  Single cell specifying the core interrupt priority level (4-15) where
+  4 is highest priority and 15 is lowest priority.
+
+  Example
+  -------
+  core_pic: interrupt-controller@0 {
+	interrupt-controller;
+	#interrupt-cells = <1>;
+	compatible = "ti,c64x+core-pic";
+  };
+
+
+
+* C64x+ Megamodule Interrupt Controller
+
+  The megamodule PIC consists of four interrupt mupliplexers each of which
+  combine up to 32 interrupt inputs into a single interrupt output which
+  may be cascaded into the core interrupt controller. The megamodule PIC
+  has a total of 12 outputs cascading into the core interrupt controller.
+  One for each core interrupt priority level. In addition to the combined
+  interrupt sources, individual megamodule interrupts may be cascaded to
+  the core interrupt controller. When an individual interrupt is cascaded,
+  it is no longer handled through a megamodule interrupt combiner and is
+  considered to have the core interrupt controller as the parent.
+
+  Required properties:
+  --------------------
+  - compatible: "ti,c64x+megamod-pic"
+  - interrupt-controller
+  - #interrupt-cells: <1>
+  - reg: base address and size of register area
+  - interrupt-parent: must be core interrupt controller
+  - interrupts: This should have four cells; one for each interrupt combiner.
+                The cells contain the core priority interrupt to which the
+                corresponding combiner output is wired.
+
+  Optional properties:
+  --------------------
+  - ti,c64x+megamod-pic-mux: Array of 12 cells correspnding to the 12 core
+                             priority interrupts. The first cell corresponds to
+                             core priority 4 and the last cell corresponds to
+                             core priority 15. The value of each cell is the
+                             megamodule interrupt source which is MUXed to
+                             the core interrupt corresponding to the cell
+                             position. Allowed values are 4 - 127. Mapping for
+                             interrupts 0 - 3 (combined interrupt sources) are
+                             ignored.
+
+  Interrupt Specifier Definition
+  ------------------------------
+  Single cell specifying the megamodule interrupt source (4-127). Note that
+  interrupts mapped directly to the core with "ti,c64x+megamod-pic-mux" will
+  use the core interrupt controller as their parent and the specifier will
+  be the core priority level, not the megamodule interrupt number.
+
+  Examples
+  --------
+  megamod_pic: interrupt-controller@1800000 {
+	compatible = "ti,c64x+megamod-pic";
+	interrupt-controller;
+	#interrupt-cells = <1>;
+	reg = <0x1800000 0x1000>;
+	interrupt-parent = <&core_pic>;
+	interrupts = < 12 13 14 15 >;
+  };
+
+  This is a minimal example where all individual interrupts go through a
+  combiner. Combiner-0 is mapped to core interrupt 12, combiner-1 is mapped
+  to interrupt 13, etc.
+
+
+  megamod_pic: interrupt-controller@1800000 {
+	compatible = "ti,c64x+megamod-pic";
+	interrupt-controller;
+	#interrupt-cells = <1>;
+	reg = <0x1800000 0x1000>;
+	interrupt-parent = <&core_pic>;
+	interrupts = < 12 13 14 15 >;
+	ti,c64x+megamod-pic-mux = <  0  0  0  0
+                                    32  0  0  0
+                                     0  0  0  0 >;
+  };
+
+  This the same as the first example except that megamodule interrupt 32 is
+  mapped directly to core priority interrupt 8. The node using this interrupt
+  must set the core controller as its interrupt parent and use 8 in the
+  interrupt specifier value.
diff --git a/dts/Bindings/c6x/soc.txt b/dts/Bindings/c6x/soc.txt
new file mode 100644
index 0000000000..b1e4973b57
--- /dev/null
+++ b/dts/Bindings/c6x/soc.txt
@@ -0,0 +1,28 @@
+C6X System-on-Chip
+------------------
+
+Required properties:
+
+- compatible: "simple-bus"
+- #address-cells: must be 1
+- #size-cells: must be 1
+- ranges
+
+Optional properties:
+
+- model: specific SoC model
+
+- nodes for IP blocks within SoC
+
+
+Example:
+
+	soc {
+		compatible = "simple-bus";
+		model = "tms320c6455";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		...
+	};
diff --git a/dts/Bindings/c6x/timer64.txt b/dts/Bindings/c6x/timer64.txt
new file mode 100644
index 0000000000..95911fe702
--- /dev/null
+++ b/dts/Bindings/c6x/timer64.txt
@@ -0,0 +1,26 @@
+Timer64
+-------
+
+The timer64 node describes C6X event timers.
+
+Required properties:
+
+- compatible: must be "ti,c64x+timer64"
+- reg: base address and size of register region
+- interrupt-parent: interrupt controller
+- interrupts: interrupt id
+
+Optional properties:
+
+- ti,dscr-dev-enable: Device ID used to enable timer IP through DSCR interface.
+
+- ti,core-mask: on multi-core SoCs, bitmask of cores allowed to use this timer.
+
+Example:
+	timer0: timer@25e0000 {
+		compatible = "ti,c64x+timer64";
+		ti,core-mask = < 0x01 >;
+		reg = <0x25e0000 0x40>;
+		interrupt-parent = <&megamod_pic>;
+		interrupts = < 16 >;
+	};