dts: update to v4.4-rc1

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

4 files changed, 364 insertions, 0 deletions

diff --git a/dts/Bindings/display/imx/fsl,imx-fb.txt b/dts/Bindings/display/imx/fsl,imx-fb.txt
new file mode 100644
index 0000000000..00d5f8ea7e
--- /dev/null
+++ b/dts/Bindings/display/imx/fsl,imx-fb.txt
@@ -0,0 +1,55 @@
+Freescale imx21 Framebuffer
+
+This framebuffer driver supports devices imx1, imx21, imx25, and imx27.
+
+Required properties:
+- compatible : "fsl,<chip>-fb", chip should be imx1 or imx21
+- reg : Should contain 1 register ranges(address and length)
+- interrupts : One interrupt of the fb dev
+
+Required nodes:
+- display: Phandle to a display node as described in
+	Documentation/devicetree/bindings/display/display-timing.txt
+	Additional, the display node has to define properties:
+	- bits-per-pixel: Bits per pixel
+	- fsl,pcr: LCDC PCR value
+
+Optional properties:
+- lcd-supply: Regulator for LCD supply voltage.
+- fsl,dmacr: DMA Control Register value. This is optional. By default, the
+	register is not modified as recommended by the datasheet.
+- fsl,lpccr: Contrast Control Register value. This property provides the
+	default value for the contrast control register.
+	If that property is omitted, the register is zeroed.
+- fsl,lscr1: LCDC Sharp Configuration Register value.
+
+Example:
+
+	imxfb: fb@10021000 {
+		compatible = "fsl,imx21-fb";
+		interrupts = <61>;
+		reg = <0x10021000 0x1000>;
+		display = <&display0>;
+	};
+
+	...
+
+	display0: display0 {
+		model = "Primeview-PD050VL1";
+		native-mode = <&timing_disp0>;
+		bits-per-pixel = <16>;
+		fsl,pcr = <0xf0c88080>;	/* non-standard but required */
+		display-timings {
+			timing_disp0: 640x480 {
+				hactive = <640>;
+				vactive = <480>;
+				hback-porch = <112>;
+				hfront-porch = <36>;
+				hsync-len = <32>;
+				vback-porch = <33>;
+				vfront-porch = <33>;
+				vsync-len = <2>;
+				clock-frequency = <25000000>;
+			};
+		};
+	};
diff --git a/dts/Bindings/display/imx/fsl-imx-drm.txt b/dts/Bindings/display/imx/fsl-imx-drm.txt
new file mode 100644
index 0000000000..971c3eedb1
--- /dev/null
+++ b/dts/Bindings/display/imx/fsl-imx-drm.txt
@@ -0,0 +1,105 @@
+Freescale i.MX DRM master device
+================================
+
+The freescale i.MX DRM master device is a virtual device needed to list all
+IPU or other display interface nodes that comprise the graphics subsystem.
+
+Required properties:
+- compatible: Should be "fsl,imx-display-subsystem"
+- ports: Should contain a list of phandles pointing to display interface ports
+  of IPU devices
+
+example:
+
+display-subsystem {
+	compatible = "fsl,display-subsystem";
+	ports = <&ipu_di0>;
+};
+
+
+Freescale i.MX IPUv3
+====================
+
+Required properties:
+- compatible: Should be "fsl,<chip>-ipu"
+- reg: should be register base and length as documented in the
+  datasheet
+- interrupts: Should contain sync interrupt and error interrupt,
+  in this order.
+- resets: phandle pointing to the system reset controller and
+          reset line index, see reset/fsl,imx-src.txt for details
+Optional properties:
+- port@[0-3]: Port nodes with endpoint definitions as defined in
+  Documentation/devicetree/bindings/media/video-interfaces.txt.
+  Ports 0 and 1 should correspond to CSI0 and CSI1,
+  ports 2 and 3 should correspond to DI0 and DI1, respectively.
+
+example:
+
+ipu: ipu@18000000 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	compatible = "fsl,imx53-ipu";
+	reg = <0x18000000 0x080000000>;
+	interrupts = <11 10>;
+	resets = <&src 2>;
+
+	ipu_di0: port@2 {
+		reg = <2>;
+
+		ipu_di0_disp0: endpoint {
+			remote-endpoint = <&display_in>;
+		};
+	};
+};
+
+Parallel display support
+========================
+
+Required properties:
+- compatible: Should be "fsl,imx-parallel-display"
+Optional properties:
+- interface_pix_fmt: How this display is connected to the
+  display interface. Currently supported types: "rgb24", "rgb565", "bgr666"
+  and "lvds666".
+- edid: verbatim EDID data block describing attached display.
+- ddc: phandle describing the i2c bus handling the display data
+  channel
+- port@[0-1]: Port nodes with endpoint definitions as defined in
+  Documentation/devicetree/bindings/media/video-interfaces.txt.
+  Port 0 is the input port connected to the IPU display interface,
+  port 1 is the output port connected to a panel.
+
+example:
+
+display@di0 {
+	compatible = "fsl,imx-parallel-display";
+	edid = [edid-data];
+	interface-pix-fmt = "rgb24";
+
+	port@0 {
+		reg = <0>;
+
+		display_in: endpoint {
+			remote-endpoint = <&ipu_di0_disp0>;
+		};
+	};
+
+	port@1 {
+		reg = <1>;
+
+		display_out: endpoint {
+			remote-endpoint = <&panel_in>;
+		};
+	};
+};
+
+panel {
+	...
+
+	port {
+		panel_in: endpoint {
+			remote-endpoint = <&display_out>;
+		};
+	};
+};
diff --git a/dts/Bindings/display/imx/hdmi.txt b/dts/Bindings/display/imx/hdmi.txt
new file mode 100644
index 0000000000..1b756cf9af
--- /dev/null
+++ b/dts/Bindings/display/imx/hdmi.txt
@@ -0,0 +1,58 @@
+Device-Tree bindings for HDMI Transmitter
+
+HDMI Transmitter
+================
+
+The HDMI Transmitter is a Synopsys DesignWare HDMI 1.4 TX controller IP
+with accompanying PHY IP.
+
+Required properties:
+ - #address-cells : should be <1>
+ - #size-cells : should be <0>
+ - compatible : should be "fsl,imx6q-hdmi" or "fsl,imx6dl-hdmi".
+ - gpr : should be <&gpr>.
+   The phandle points to the iomuxc-gpr region containing the HDMI
+   multiplexer control register.
+ - clocks, clock-names : phandles to the HDMI iahb and isrf clocks, as described
+   in Documentation/devicetree/bindings/clock/clock-bindings.txt and
+   Documentation/devicetree/bindings/clock/imx6q-clock.txt.
+ - port@[0-4]: Up to four port nodes with endpoint definitions as defined in
+   Documentation/devicetree/bindings/media/video-interfaces.txt,
+   corresponding to the four inputs to the HDMI multiplexer.
+
+Optional properties:
+ - ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
+
+example:
+
+	gpr: iomuxc-gpr@020e0000 {
+		/* ... */
+	};
+
+        hdmi: hdmi@0120000 {
+                #address-cells = <1>;
+                #size-cells = <0>;
+                compatible = "fsl,imx6q-hdmi";
+                reg = <0x00120000 0x9000>;
+                interrupts = <0 115 0x04>;
+                gpr = <&gpr>;
+                clocks = <&clks 123>, <&clks 124>;
+                clock-names = "iahb", "isfr";
+                ddc-i2c-bus = <&i2c2>;
+
+                port@0 {
+                        reg = <0>;
+
+                        hdmi_mux_0: endpoint {
+                                remote-endpoint = <&ipu1_di0_hdmi>;
+                        };
+                };
+
+                port@1 {
+                        reg = <1>;
+
+                        hdmi_mux_1: endpoint {
+                                remote-endpoint = <&ipu1_di1_hdmi>;
+                        };
+                };
+        };
diff --git a/dts/Bindings/display/imx/ldb.txt b/dts/Bindings/display/imx/ldb.txt
new file mode 100644
index 0000000000..0a175d991b
--- /dev/null
+++ b/dts/Bindings/display/imx/ldb.txt
@@ -0,0 +1,146 @@
+Device-Tree bindings for LVDS Display Bridge (ldb)
+
+LVDS Display Bridge
+===================
+
+The LVDS Display Bridge device tree node contains up to two lvds-channel
+nodes describing each of the two LVDS encoder channels of the bridge.
+
+Required properties:
+ - #address-cells : should be <1>
+ - #size-cells : should be <0>
+ - compatible : should be "fsl,imx53-ldb" or "fsl,imx6q-ldb".
+                Both LDB versions are similar, but i.MX6 has an additional
+                multiplexer in the front to select any of the four IPU display
+                interfaces as input for each LVDS channel.
+ - gpr : should be <&gpr> on i.MX53 and i.MX6q.
+         The phandle points to the iomuxc-gpr region containing the LVDS
+         control register.
+- clocks, clock-names : phandles to the LDB divider and selector clocks and to
+                        the display interface selector clocks, as described in
+                        Documentation/devicetree/bindings/clock/clock-bindings.txt
+        The following clocks are expected on i.MX53:
+                "di0_pll" - LDB LVDS channel 0 mux
+                "di1_pll" - LDB LVDS channel 1 mux
+                "di0" - LDB LVDS channel 0 gate
+                "di1" - LDB LVDS channel 1 gate
+                "di0_sel" - IPU1 DI0 mux
+                "di1_sel" - IPU1 DI1 mux
+        On i.MX6q the following additional clocks are needed:
+                "di2_sel" - IPU2 DI0 mux
+                "di3_sel" - IPU2 DI1 mux
+        The needed clock numbers for each are documented in
+        Documentation/devicetree/bindings/clock/imx5-clock.txt, and in
+        Documentation/devicetree/bindings/clock/imx6q-clock.txt.
+
+Optional properties:
+ - pinctrl-names : should be "default" on i.MX53, not used on i.MX6q
+ - pinctrl-0 : a phandle pointing to LVDS pin settings on i.MX53,
+               not used on i.MX6q
+ - fsl,dual-channel : boolean. if it exists, only LVDS channel 0 should
+   be configured - one input will be distributed on both outputs in dual
+   channel mode
+
+LVDS Channel
+============
+
+Each LVDS Channel has to contain either an of graph link to a panel device node
+or a display-timings node that describes the video timings for the connected
+LVDS display as well as the fsl,data-mapping and fsl,data-width properties.
+
+Required properties:
+ - reg : should be <0> or <1>
+ - port: Input and output port nodes with endpoint definitions as defined in
+   Documentation/devicetree/bindings/graph.txt.
+   On i.MX5, the internal two-input-multiplexer is used. Due to hardware
+   limitations, only one input port (port@[0,1]) can be used for each channel
+   (lvds-channel@[0,1], respectively).
+   On i.MX6, there should be four input ports (port@[0-3]) that correspond
+   to the four LVDS multiplexer inputs.
+   A single output port (port@2 on i.MX5, port@4 on i.MX6) must be connected
+   to a panel input port. Optionally, the output port can be left out if
+   display-timings are used instead.
+
+Optional properties (required if display-timings are used):
+ - display-timings : A node that describes the display timings as defined in
+   Documentation/devicetree/bindings/display/display-timing.txt.
+ - fsl,data-mapping : should be "spwg" or "jeida"
+                      This describes how the color bits are laid out in the
+                      serialized LVDS signal.
+ - fsl,data-width : should be <18> or <24>
+
+example:
+
+gpr: iomuxc-gpr@53fa8000 {
+	/* ... */
+};
+
+ldb: ldb@53fa8008 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	compatible = "fsl,imx53-ldb";
+	gpr = <&gpr>;
+	clocks = <&clks IMX5_CLK_LDB_DI0_SEL>,
+		 <&clks IMX5_CLK_LDB_DI1_SEL>,
+		 <&clks IMX5_CLK_IPU_DI0_SEL>,
+		 <&clks IMX5_CLK_IPU_DI1_SEL>,
+		 <&clks IMX5_CLK_LDB_DI0_GATE>,
+		 <&clks IMX5_CLK_LDB_DI1_GATE>;
+	clock-names = "di0_pll", "di1_pll",
+		      "di0_sel", "di1_sel",
+		      "di0", "di1";
+
+	/* Using an of-graph endpoint link to connect the panel */
+	lvds-channel@0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			lvds0_in: endpoint {
+				remote-endpoint = <&ipu_di0_lvds0>;
+			};
+		};
+
+		port@2 {
+			reg = <2>;
+
+			lvds0_out: endpoint {
+				remote-endpoint = <&panel_in>;
+			};
+		};
+	};
+
+	/* Using display-timings and fsl,data-mapping/width instead */
+	lvds-channel@1 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <1>;
+		fsl,data-mapping = "spwg";
+		fsl,data-width = <24>;
+
+		display-timings {
+			/* ... */
+		};
+
+		port@1 {
+			reg = <1>;
+
+			lvds1_in: endpoint {
+				remote-endpoint = <&ipu_di1_lvds1>;
+			};
+		};
+	};
+};
+
+panel: lvds-panel {
+	/* ... */
+
+	port {
+		panel_in: endpoint {
+			remote-endpoint = <&lvds0_out>;
+		};
+	};
+};