dts: update to v4.18-rc1

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

8 files changed, 329 insertions, 18 deletions

diff --git a/dts/Bindings/display/bridge/adi,adv7511.txt b/dts/Bindings/display/bridge/adi,adv7511.txt
index 0047b1394c..2c88753625 100644
--- a/dts/Bindings/display/bridge/adi,adv7511.txt
+++ b/dts/Bindings/display/bridge/adi,adv7511.txt
@@ -14,7 +14,13 @@ Required properties:
 		"adi,adv7513"
 		"adi,adv7533"
 
-- reg: I2C slave address
+- reg: I2C slave addresses
+  The ADV7511 internal registers are split into four pages exposed through
+  different I2C addresses, creating four register maps. Each map has it own
+  I2C address and acts as a standard slave device on the I2C bus. The main
+  address is mandatory, others are optional and revert to defaults if not
+  specified.
+
 
 The ADV7511 supports a large number of input data formats that differ by their
 color depth, color format, clock mode, bit justification and random
@@ -70,6 +76,9 @@ Optional properties:
   rather than generate its own timings for HDMI output.
 - clocks: from common clock binding: reference to the CEC clock.
 - clock-names: from common clock binding: must be "cec".
+- reg-names : Names of maps with programmable addresses.
+	It can contain any map needing a non-default address.
+	Possible maps names are : "main", "edid", "cec", "packet"
 
 Required nodes:
 
@@ -88,7 +97,12 @@ Example
 
 	adv7511w: hdmi@39 {
 		compatible = "adi,adv7511w";
-		reg = <39>;
+		/*
+		 * The EDID page will be accessible on address 0x66 on the I2C
+		 * bus. All other maps continue to use their default addresses.
+		 */
+		reg = <0x39>, <0x66>;
+		reg-names = "main", "edid";
 		interrupt-parent = <&gpio3>;
 		interrupts = <29 IRQ_TYPE_EDGE_FALLING>;
 		clocks = <&cec_clock>;
diff --git a/dts/Bindings/display/bridge/cdns,dsi.txt b/dts/Bindings/display/bridge/cdns,dsi.txt
new file mode 100644
index 0000000000..f5725bb6c6
--- /dev/null
+++ b/dts/Bindings/display/bridge/cdns,dsi.txt
@@ -0,0 +1,133 @@
+Cadence DSI bridge
+==================
+
+The Cadence DSI bridge is a DPI to DSI bridge supporting up to 4 DSI lanes.
+
+Required properties:
+- compatible: should be set to "cdns,dsi".
+- reg: physical base address and length of the controller's registers.
+- interrupts: interrupt line connected to the DSI bridge.
+- clocks: DSI bridge clocks.
+- clock-names: must contain "dsi_p_clk" and "dsi_sys_clk".
+- phys: phandle link to the MIPI D-PHY controller.
+- phy-names: must contain "dphy".
+- #address-cells: must be set to 1.
+- #size-cells: must be set to 0.
+
+Optional properties:
+- resets: DSI reset lines.
+- reset-names: can contain "dsi_p_rst".
+
+Required subnodes:
+- ports: Ports as described in Documentation/devicetree/bindings/graph.txt.
+  2 ports are available:
+  * port 0: this port is only needed if some of your DSI devices are
+	    controlled through  an external bus like I2C or SPI. Can have at
+	    most 4 endpoints. The endpoint number is directly encoding the
+	    DSI virtual channel used by this device.
+  * port 1: represents the DPI input.
+  Other ports will be added later to support the new kind of inputs.
+
+- one subnode per DSI device connected on the DSI bus. Each DSI device should
+  contain a reg property encoding its virtual channel.
+
+Cadence DPHY
+============
+
+Cadence DPHY block.
+
+Required properties:
+- compatible: should be set to "cdns,dphy".
+- reg: physical base address and length of the DPHY registers.
+- clocks: DPHY reference clocks.
+- clock-names: must contain "psm" and "pll_ref".
+- #phy-cells: must be set to 0.
+
+
+Example:
+	dphy0: dphy@fd0e0000{
+		compatible = "cdns,dphy";
+		reg = <0x0 0xfd0e0000 0x0 0x1000>;
+		clocks = <&psm_clk>, <&pll_ref_clk>;
+		clock-names = "psm", "pll_ref";
+		#phy-cells = <0>;
+	};
+
+	dsi0: dsi@fd0c0000 {
+		compatible = "cdns,dsi";
+		reg = <0x0 0xfd0c0000 0x0 0x1000>;
+		clocks = <&pclk>, <&sysclk>;
+		clock-names = "dsi_p_clk", "dsi_sys_clk";
+		interrupts = <1>;
+		phys = <&dphy0>;
+		phy-names = "dphy";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@1 {
+				reg = <1>;
+				dsi0_dpi_input: endpoint {
+					remote-endpoint = <&xxx_dpi_output>;
+				};
+			};
+		};
+
+		panel: dsi-dev@0 {
+			compatible = "<vendor,panel>";
+			reg = <0>;
+		};
+	};
+
+or
+
+	dsi0: dsi@fd0c0000 {
+		compatible = "cdns,dsi";
+		reg = <0x0 0xfd0c0000 0x0 0x1000>;
+		clocks = <&pclk>, <&sysclk>;
+		clock-names = "dsi_p_clk", "dsi_sys_clk";
+		interrupts = <1>;
+		phys = <&dphy1>;
+		phy-names = "dphy";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				dsi0_output: endpoint@0 {
+					reg = <0>;
+					remote-endpoint = <&dsi_panel_input>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+				dsi0_dpi_input: endpoint {
+					remote-endpoint = <&xxx_dpi_output>;
+				};
+			};
+		};
+	};
+
+	i2c@xxx {
+		panel: panel@59 {
+			compatible = "<vendor,panel>";
+			reg = <0x59>;
+
+			port {
+				dsi_panel_input: endpoint {
+					remote-endpoint = <&dsi0_output>;
+				};
+			};
+		};
+	};
diff --git a/dts/Bindings/display/bridge/renesas,dw-hdmi.txt b/dts/Bindings/display/bridge/renesas,dw-hdmi.txt
index 3a72a103a1..a41d280c3f 100644
--- a/dts/Bindings/display/bridge/renesas,dw-hdmi.txt
+++ b/dts/Bindings/display/bridge/renesas,dw-hdmi.txt
@@ -14,6 +14,7 @@ Required properties:
 - compatible : Shall contain one or more of
   - "renesas,r8a7795-hdmi" for R8A7795 (R-Car H3) compatible HDMI TX
   - "renesas,r8a7796-hdmi" for R8A7796 (R-Car M3-W) compatible HDMI TX
+  - "renesas,r8a77965-hdmi" for R8A77965 (R-Car M3-N) compatible HDMI TX
   - "renesas,rcar-gen3-hdmi" for the generic R-Car Gen3 compatible HDMI TX
 
     When compatible with generic versions, nodes must list the SoC-specific
diff --git a/dts/Bindings/display/bridge/tda998x.txt b/dts/Bindings/display/bridge/tda998x.txt
index 24cc246618..f5a02f61dd 100644
--- a/dts/Bindings/display/bridge/tda998x.txt
+++ b/dts/Bindings/display/bridge/tda998x.txt
@@ -27,7 +27,10 @@ Optional properties:
 	in question is used. The implementation allows one or two DAIs. If two
 	DAIs are defined, they must be of different type.
 
-[1] Documentation/sound/alsa/soc/DAI.txt
+  - nxp,calib-gpios: calibration GPIO, which must correspond with the
+	gpio used for the TDA998x interrupt pin.
+
+[1] Documentation/sound/soc/dai.rst
 [2] include/dt-bindings/display/tda998x.h
 
 Example:
diff --git a/dts/Bindings/display/bridge/thine,thc63lvd1024.txt b/dts/Bindings/display/bridge/thine,thc63lvd1024.txt
new file mode 100644
index 0000000000..37f0c04d5a
--- /dev/null
+++ b/dts/Bindings/display/bridge/thine,thc63lvd1024.txt
@@ -0,0 +1,60 @@
+Thine Electronics THC63LVD1024 LVDS decoder
+-------------------------------------------
+
+The THC63LVD1024 is a dual link LVDS receiver designed to convert LVDS streams
+to parallel data outputs. The chip supports single/dual input/output modes,
+handling up to two LVDS input streams and up to two digital CMOS/TTL outputs.
+
+Single or dual operation mode, output data mapping and DDR output modes are
+configured through input signals and the chip does not expose any control bus.
+
+Required properties:
+- compatible: Shall be "thine,thc63lvd1024"
+- vcc-supply: Power supply for TTL output, TTL CLOCKOUT signal, LVDS input,
+  PPL and digital circuitry
+
+Optional properties:
+- powerdown-gpios: Power down GPIO signal, pin name "/PDWN". Active low
+- oe-gpios: Output enable GPIO signal, pin name "OE". Active high
+
+The THC63LVD1024 video port connections are modeled according
+to OF graph bindings specified by Documentation/devicetree/bindings/graph.txt
+
+Required video port nodes:
+- port@0: First LVDS input port
+- port@2: First digital CMOS/TTL parallel output
+
+Optional video port nodes:
+- port@1: Second LVDS input port
+- port@3: Second digital CMOS/TTL parallel output
+
+Example:
+--------
+
+	thc63lvd1024: lvds-decoder {
+		compatible = "thine,thc63lvd1024";
+
+		vcc-supply = <&reg_lvds_vcc>;
+		powerdown-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				lvds_dec_in_0: endpoint {
+					remote-endpoint = <&lvds_out>;
+				};
+			};
+
+			port@2{
+				reg = <2>;
+
+				lvds_dec_out_2: endpoint {
+					remote-endpoint = <&adv7511_in>;
+				};
+			};
+		};
+	};
diff --git a/dts/Bindings/display/exynos/exynos5433-decon.txt b/dts/Bindings/display/exynos/exynos5433-decon.txt
index fc2588292a..775193e1c6 100644
--- a/dts/Bindings/display/exynos/exynos5433-decon.txt
+++ b/dts/Bindings/display/exynos/exynos5433-decon.txt
@@ -19,7 +19,8 @@ Required properties:
 	  clock-names property.
 - clock-names: list of clock names sorted in the same order as the clocks
 	       property. Must contain "pclk", "aclk_decon", "aclk_smmu_decon0x",
-	       "aclk_xiu_decon0x", "pclk_smmu_decon0x", clk_decon_vclk",
+	       "aclk_xiu_decon0x", "pclk_smmu_decon0x", "aclk_smmu_decon1x",
+	       "aclk_xiu_decon1x", "pclk_smmu_decon1x", clk_decon_vclk",
 	       "sclk_decon_eclk"
 - ports: contains a port which is connected to mic node. address-cells and
 	 size-cells must 1 and 0, respectively.
@@ -34,10 +35,14 @@ decon: decon@13800000 {
 	clocks = <&cmu_disp CLK_ACLK_DECON>, <&cmu_disp CLK_ACLK_SMMU_DECON0X>,
 		<&cmu_disp CLK_ACLK_XIU_DECON0X>,
 		<&cmu_disp CLK_PCLK_SMMU_DECON0X>,
+		<&cmu_disp CLK_ACLK_SMMU_DECON1X>,
+		<&cmu_disp CLK_ACLK_XIU_DECON1X>,
+		<&cmu_disp CLK_PCLK_SMMU_DECON1X>,
 		<&cmu_disp CLK_SCLK_DECON_VCLK>,
 		<&cmu_disp CLK_SCLK_DECON_ECLK>;
 	clock-names = "aclk_decon", "aclk_smmu_decon0x", "aclk_xiu_decon0x",
-		"pclk_smmu_decon0x", "sclk_decon_vclk", "sclk_decon_eclk";
+		"pclk_smmu_decon0x", "aclk_smmu_decon1x", "aclk_xiu_decon1x",
+		"pclk_smmu_decon1x", "sclk_decon_vclk", "sclk_decon_eclk";
 	interrupt-names = "vsync", "lcd_sys";
 	interrupts = <0 202 0>, <0 203 0>;
 
diff --git a/dts/Bindings/display/renesas,du.txt b/dts/Bindings/display/renesas,du.txt
index c9cd17f997..7c6854bd0a 100644
--- a/dts/Bindings/display/renesas,du.txt
+++ b/dts/Bindings/display/renesas,du.txt
@@ -13,6 +13,7 @@ Required Properties:
     - "renesas,du-r8a7794" for R8A7794 (R-Car E2) compatible DU
     - "renesas,du-r8a7795" for R8A7795 (R-Car H3) compatible DU
     - "renesas,du-r8a7796" for R8A7796 (R-Car M3-W) compatible DU
+    - "renesas,du-r8a77965" for R8A77965 (R-Car M3-N) compatible DU
     - "renesas,du-r8a77970" for R8A77970 (R-Car V3M) compatible DU
     - "renesas,du-r8a77995" for R8A77995 (R-Car D3) compatible DU
 
@@ -47,20 +48,21 @@ bindings specified in Documentation/devicetree/bindings/graph.txt.
 The following table lists for each supported model the port number
 corresponding to each DU output.
 
-                      Port0          Port1          Port2          Port3
+                        Port0          Port1          Port2          Port3
 -----------------------------------------------------------------------------
- R8A7743 (RZ/G1M)     DPAD 0         LVDS 0         -              -
- R8A7745 (RZ/G1E)     DPAD 0         DPAD 1         -              -
- R8A7779 (R-Car H1)   DPAD 0         DPAD 1         -              -
- R8A7790 (R-Car H2)   DPAD 0         LVDS 0         LVDS 1         -
- R8A7791 (R-Car M2-W) DPAD 0         LVDS 0         -              -
- R8A7792 (R-Car V2H)  DPAD 0         DPAD 1         -              -
- R8A7793 (R-Car M2-N) DPAD 0         LVDS 0         -              -
- R8A7794 (R-Car E2)   DPAD 0         DPAD 1         -              -
- R8A7795 (R-Car H3)   DPAD 0         HDMI 0         HDMI 1         LVDS 0
- R8A7796 (R-Car M3-W) DPAD 0         HDMI 0         LVDS 0         -
- R8A77970 (R-Car V3M) DPAD 0         LVDS 0         -              -
- R8A77995 (R-Car D3)  DPAD 0         LVDS 0         LVDS 1         -
+ R8A7743 (RZ/G1M)       DPAD 0         LVDS 0         -              -
+ R8A7745 (RZ/G1E)       DPAD 0         DPAD 1         -              -
+ R8A7779 (R-Car H1)     DPAD 0         DPAD 1         -              -
+ R8A7790 (R-Car H2)     DPAD 0         LVDS 0         LVDS 1         -
+ R8A7791 (R-Car M2-W)   DPAD 0         LVDS 0         -              -
+ R8A7792 (R-Car V2H)    DPAD 0         DPAD 1         -              -
+ R8A7793 (R-Car M2-N)   DPAD 0         LVDS 0         -              -
+ R8A7794 (R-Car E2)     DPAD 0         DPAD 1         -              -
+ R8A7795 (R-Car H3)     DPAD 0         HDMI 0         HDMI 1         LVDS 0
+ R8A7796 (R-Car M3-W)   DPAD 0         HDMI 0         LVDS 0         -
+ R8A77965 (R-Car M3-N)  DPAD 0         HDMI 0         LVDS 0         -
+ R8A77970 (R-Car V3M)   DPAD 0         LVDS 0         -              -
+ R8A77995 (R-Car D3)    DPAD 0         LVDS 0         LVDS 1         -
 
 
 Example: R8A7795 (R-Car H3) ES2.0 DU
diff --git a/dts/Bindings/display/sunxi/sun6i-dsi.txt b/dts/Bindings/display/sunxi/sun6i-dsi.txt
new file mode 100644
index 0000000000..6a6cf5de08
--- /dev/null
+++ b/dts/Bindings/display/sunxi/sun6i-dsi.txt
@@ -0,0 +1,93 @@
+Allwinner A31 DSI Encoder
+=========================
+
+The DSI pipeline consists of two separate blocks: the DSI controller
+itself, and its associated D-PHY.
+
+DSI Encoder
+-----------
+
+The DSI Encoder generates the DSI signal from the TCON's.
+
+Required properties:
+  - compatible: value must be one of:
+    * allwinner,sun6i-a31-mipi-dsi
+  - reg: base address and size of memory-mapped region
+  - interrupts: interrupt associated to this IP
+  - clocks: phandles to the clocks feeding the DSI encoder
+    * bus: the DSI interface clock
+    * mod: the DSI module clock
+  - clock-names: the clock names mentioned above
+  - phys: phandle to the D-PHY
+  - phy-names: must be "dphy"
+  - resets: phandle to the reset controller driving the encoder
+
+  - ports: A ports node with endpoint definitions as defined in
+    Documentation/devicetree/bindings/media/video-interfaces.txt. The
+    first port should be the input endpoint, usually coming from the
+    associated TCON.
+
+Any MIPI-DSI device attached to this should be described according to
+the bindings defined in ../mipi-dsi-bus.txt
+
+D-PHY
+-----
+
+Required properties:
+  - compatible: value must be one of:
+    * allwinner,sun6i-a31-mipi-dphy
+  - reg: base address and size of memory-mapped region
+  - clocks: phandles to the clocks feeding the DSI encoder
+    * bus: the DSI interface clock
+    * mod: the DSI module clock
+  - clock-names: the clock names mentioned above
+  - resets: phandle to the reset controller driving the encoder
+
+Example:
+
+dsi0: dsi@1ca0000 {
+	compatible = "allwinner,sun6i-a31-mipi-dsi";
+	reg = <0x01ca0000 0x1000>;
+	interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
+	clocks = <&ccu CLK_BUS_MIPI_DSI>,
+		 <&ccu CLK_DSI_SCLK>;
+	clock-names = "bus", "mod";
+	resets = <&ccu RST_BUS_MIPI_DSI>;
+	phys = <&dphy0>;
+	phy-names = "dphy";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	panel@0 {
+		compatible = "bananapi,lhr050h41", "ilitek,ili9881c";
+		reg = <0>;
+		power-gpios = <&pio 1 7 GPIO_ACTIVE_HIGH>; /* PB07 */
+		reset-gpios = <&r_pio 0 5 GPIO_ACTIVE_LOW>; /* PL05 */
+		backlight = <&pwm_bl>;
+	};
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			dsi0_in_tcon0: endpoint {
+				remote-endpoint = <&tcon0_out_dsi0>;
+			};
+		};
+	};
+};
+
+dphy0: d-phy@1ca1000 {
+	compatible = "allwinner,sun6i-a31-mipi-dphy";
+	reg = <0x01ca1000 0x1000>;
+	clocks = <&ccu CLK_BUS_MIPI_DSI>,
+		 <&ccu CLK_DSI_DPHY>;
+	clock-names = "bus", "mod";
+	resets = <&ccu RST_BUS_MIPI_DSI>;
+	#phy-cells = <0>;
+};