Add devicetree source files as of Linux-3.15-rc2

This adds the Linux dts files to barebox. The dts files are
generated from Ian Campbells device-tree-rebasing.git:

git://xenbits.xen.org/people/ianc/device-tree-rebasing.git

The dts are found in dts/ in the barebox repository and
will be updated from upstream regularly, probably for each upstream
-rc.

To keep the synchronization with upstream easy no changes to
the original files are allowed under dts/. Instead changes to
upstream dts files will be done using overlays in arch/$ARCH/dts/.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

1 files changed, 48 insertions, 0 deletions

diff --git a/dts/Bindings/gpio/gpio-xilinx.txt b/dts/Bindings/gpio/gpio-xilinx.txt
new file mode 100644
index 0000000000..63bf4becd5
--- /dev/null
+++ b/dts/Bindings/gpio/gpio-xilinx.txt
@@ -0,0 +1,48 @@
+Xilinx plb/axi GPIO controller
+
+Dual channel GPIO controller with configurable number of pins
+(from 1 to 32 per channel). Every pin can be configured as
+input/output/tristate. Both channels share the same global IRQ but
+local interrupts can be enabled on channel basis.
+
+Required properties:
+- compatible : Should be "xlnx,xps-gpio-1.00.a"
+- reg : Address and length of the register set for the device
+- #gpio-cells : Should be two. The first cell is the pin number and the
+  second cell is used to specify optional parameters (currently unused).
+- gpio-controller : Marks the device node as a GPIO controller.
+
+Optional properties:
+- interrupts : Interrupt mapping for GPIO IRQ.
+- interrupt-parent : Phandle for the interrupt controller that
+  services interrupts for this device.
+- xlnx,all-inputs : if n-th bit is setup, GPIO-n is input
+- xlnx,dout-default : if n-th bit is 1, GPIO-n default value is 1
+- xlnx,gpio-width : gpio width
+- xlnx,tri-default : if n-th bit is 1, GPIO-n is in tristate mode
+- xlnx,is-dual : if 1, controller also uses the second channel
+- xlnx,all-inputs-2 : as above but for the second channel
+- xlnx,dout-default-2 : as above but the second channel
+- xlnx,gpio2-width : as above but for the second channel
+- xlnx,tri-default-2 : as above but for the second channel
+
+
+Example:
+gpio: gpio@40000000 {
+	#gpio-cells = <2>;
+	compatible = "xlnx,xps-gpio-1.00.a";
+	gpio-controller ;
+	interrupt-parent = <&microblaze_0_intc>;
+	interrupts = < 6 2 >;
+	reg = < 0x40000000 0x10000 >;
+	xlnx,all-inputs = <0x0>;
+	xlnx,all-inputs-2 = <0x0>;
+	xlnx,dout-default = <0x0>;
+	xlnx,dout-default-2 = <0x0>;
+	xlnx,gpio-width = <0x2>;
+	xlnx,gpio2-width = <0x2>;
+	xlnx,interrupt-present = <0x1>;
+	xlnx,is-dual = <0x1>;
+	xlnx,tri-default = <0xffffffff>;
+	xlnx,tri-default-2 = <0xffffffff>;
+} ;