dts: update to v5.8-rc1

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

7 files changed, 174 insertions, 68 deletions

diff --git a/dts/Bindings/hwmon/adi,axi-fan-control.yaml b/dts/Bindings/hwmon/adi,axi-fan-control.yaml
index 7db78767c0..af35b77053 100644
--- a/dts/Bindings/hwmon/adi,axi-fan-control.yaml
+++ b/dts/Bindings/hwmon/adi,axi-fan-control.yaml
@@ -34,8 +34,7 @@ properties:
     description:
       Value specifying the number of pulses per revolution of the controlled
       FAN.
-    allOf:
-      - $ref: /schemas/types.yaml#/definitions/uint32
+    $ref: /schemas/types.yaml#/definitions/uint32
     enum: [1, 2, 4]
 
 required:
diff --git a/dts/Bindings/hwmon/adi,ltc2947.yaml b/dts/Bindings/hwmon/adi,ltc2947.yaml
index 44a63fffb4..eef614962b 100644
--- a/dts/Bindings/hwmon/adi,ltc2947.yaml
+++ b/dts/Bindings/hwmon/adi,ltc2947.yaml
@@ -38,20 +38,18 @@ properties:
       the accumulated values, this entry can also have two items which sets
       energy1/charge1 and energy2/charger2 respectively. Check table 12 of the
       datasheet for more information on the supported options.
-    allOf:
-      - $ref: /schemas/types.yaml#/definitions/uint32-array
-      - minItems: 2
-        maxItems: 2
-        items:
-          enum: [0, 1, 2, 3]
-          default: 0
+    $ref: /schemas/types.yaml#/definitions/uint32-array
+    minItems: 2
+    maxItems: 2
+    items:
+      enum: [0, 1, 2, 3]
+      default: 0
 
   adi,accumulation-deadband-microamp:
     description:
       This property controls the Accumulation Dead band which allows to set the
       level of current below which no accumulation takes place.
-    allOf:
-      - $ref: /schemas/types.yaml#/definitions/uint32
+    $ref: /schemas/types.yaml#/definitions/uint32
     maximum: 255
     default: 0
 
@@ -61,8 +59,7 @@ properties:
       active high, setting it to zero makets it active low. When this property
       is present, the GPIO is automatically configured as output and set to
       control a fan as a function of measured temperature.
-    allOf:
-      - $ref: /schemas/types.yaml#/definitions/uint32
+    $ref: /schemas/types.yaml#/definitions/uint32
     enum: [0, 1]
     default: 0
 
@@ -74,13 +71,12 @@ properties:
       registers. Check table 13 of the datasheet for more information on the
       supported options. This property cannot be used together with
       adi,gpio-out-pol.
-    allOf:
-      - $ref: /schemas/types.yaml#/definitions/uint32-array
-      - minItems: 2
-        maxItems: 2
-        items:
-          enum: [0, 1, 2]
-          default: 0
+    $ref: /schemas/types.yaml#/definitions/uint32-array
+    minItems: 2
+    maxItems: 2
+    items:
+      enum: [0, 1, 2]
+      default: 0
 
 required:
   - compatible
diff --git a/dts/Bindings/hwmon/adt7475.yaml b/dts/Bindings/hwmon/adt7475.yaml
index 46c441574f..dfa821c0aa 100644
--- a/dts/Bindings/hwmon/adt7475.yaml
+++ b/dts/Bindings/hwmon/adt7475.yaml
@@ -46,22 +46,20 @@ patternProperties:
       set to 1 the attenuator is bypassed if set to 0 the attenuator is
       not bypassed. If the property is absent then the attenuator
       retains it's configuration from the bios/bootloader.
-    allOf:
-     - $ref: /schemas/types.yaml#/definitions/uint32
-     - enum: [0, 1]
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [0, 1]
 
   "^adi,pwm-active-state$":
     description: |
       Integer array, represents the active state of the pwm outputs If set to 0
       the pwm uses a logic low output for 100% duty cycle. If set to 1 the pwm
       uses a logic high output for 100% duty cycle.
-    allOf:
-      - $ref: /schemas/types.yaml#/definitions/uint32-array
-      - minItems: 3
-        maxItems: 3
-        items:
-          enum: [0, 1]
-          default: 1
+    $ref: /schemas/types.yaml#/definitions/uint32-array
+    minItems: 3
+    maxItems: 3
+    items:
+      enum: [0, 1]
+      default: 1
 
 required:
   - compatible
diff --git a/dts/Bindings/hwmon/baikal,bt1-pvt.yaml b/dts/Bindings/hwmon/baikal,bt1-pvt.yaml
new file mode 100644
index 0000000000..84ae4cdd08
--- /dev/null
+++ b/dts/Bindings/hwmon/baikal,bt1-pvt.yaml
@@ -0,0 +1,107 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+# Copyright (C) 2020 BAIKAL ELECTRONICS, JSC
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/hwmon/baikal,bt1-pvt.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Baikal-T1 PVT Sensor
+
+maintainers:
+  - Serge Semin <fancer.lancer@gmail.com>
+
+description: |
+  Baikal-T1 SoC provides an embedded process, voltage and temperature
+  sensor to monitor an internal SoC environment (chip temperature, supply
+  voltage and process monitor) and on time detect critical situations,
+  which may cause the system instability and even damages. The IP-block
+  is based on the Analog Bits PVT sensor, but is equipped with a dedicated
+  control wrapper, which provides a MMIO registers-based access to the
+  sensor core functionality (APB3-bus based) and exposes an additional
+  functions like thresholds/data ready interrupts, its status and masks,
+  measurements timeout. Its internal structure is depicted on the next
+  diagram:
+
+     Analog Bits core                     Bakal-T1 PVT control block
+  +--------------------+                  +------------------------+
+  | Temperature sensor |-+         +------| Sensors control        |
+  |--------------------| |<---En---|      |------------------------|
+  | Voltage sensor     |-|<--Mode--| +--->| Sampled data           |
+  |--------------------| |<--Trim--+ |    |------------------------|
+  | Low-Vt sensor      |-|           | +--| Thresholds comparator  |
+  |--------------------| |---Data----| |  |------------------------|
+  | High-Vt sensor     |-|           | +->| Interrupts status      |
+  |--------------------| |--Valid--+-+ |  |------------------------|
+  | Standard-Vt sensor |-+         +---+--| Interrupts mask        |
+  +--------------------+                  |------------------------|
+           ^                              | Interrupts timeout     |
+           |                              +------------------------+
+           |                                        ^  ^
+  Rclk-----+----------------------------------------+  |
+  APB3-------------------------------------------------+
+
+  This bindings describes the external Baikal-T1 PVT control interfaces
+  like MMIO registers space, interrupt request number and clocks source.
+  These are then used by the corresponding hwmon device driver to
+  implement the sysfs files-based access to the sensors functionality.
+
+properties:
+  compatible:
+    const: baikal,bt1-pvt
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    items:
+      - description: PVT reference clock
+      - description: APB3 interface clock
+
+  clock-names:
+    items:
+      - const: ref
+      - const: pclk
+
+  "#thermal-sensor-cells":
+    description: Baikal-T1 can be referenced as the CPU thermal-sensor
+    const: 0
+
+  baikal,pvt-temp-offset-millicelsius:
+    description: |
+      Temperature sensor trimming factor. It can be used to manually adjust the
+      temperature measurements within 7.130 degrees Celsius.
+    maxItems: 1
+    items:
+      default: 0
+      minimum: 0
+      maximum: 7130
+
+unevaluatedProperties: false
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - clock-names
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/mips-gic.h>
+
+    pvt@1f200000 {
+      compatible = "baikal,bt1-pvt";
+      reg = <0x1f200000 0x1000>;
+      #thermal-sensor-cells = <0>;
+
+      interrupts = <GIC_SHARED 31 IRQ_TYPE_LEVEL_HIGH>;
+
+      baikal,pvt-temp-trim-millicelsius = <1000>;
+
+      clocks = <&ccu_sys>, <&ccu_sys>;
+      clock-names = "ref", "pclk";
+    };
+...
diff --git a/dts/Bindings/hwmon/cirrus,lochnagar.txt b/dts/Bindings/hwmon/cirrus,lochnagar.txt
deleted file mode 100644
index ffb79ccf51..0000000000
--- a/dts/Bindings/hwmon/cirrus,lochnagar.txt
+++ /dev/null
@@ -1,26 +0,0 @@
-Cirrus Logic Lochnagar Audio Development Board
-
-Lochnagar is an evaluation and development board for Cirrus Logic
-Smart CODEC and Amp devices. It allows the connection of most Cirrus
-Logic devices on mini-cards, as well as allowing connection of
-various application processor systems to provide a full evaluation
-platform.  Audio system topology, clocking and power can all be
-controlled through the Lochnagar, allowing the device under test
-to be used in a variety of possible use cases.
-
-This binding document describes the binding for the hardware monitor
-portion of the driver.
-
-This binding must be part of the Lochnagar MFD binding:
-  [4] ../mfd/cirrus,lochnagar.txt
-
-Required properties:
-
-  - compatible : One of the following strings:
-                 "cirrus,lochnagar2-hwmon"
-
-Example:
-
-lochnagar-hwmon {
-	compatible = "cirrus,lochnagar2-hwmon";
-};
diff --git a/dts/Bindings/hwmon/cirrus,lochnagar.yaml b/dts/Bindings/hwmon/cirrus,lochnagar.yaml
new file mode 100644
index 0000000000..cc00b97a7d
--- /dev/null
+++ b/dts/Bindings/hwmon/cirrus,lochnagar.yaml
@@ -0,0 +1,35 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/hwmon/cirrus,lochnagar.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Cirrus Logic Lochnagar Audio Development Board
+
+maintainers:
+  - patches@opensource.cirrus.com
+
+description: |
+  Lochnagar is an evaluation and development board for Cirrus Logic
+  Smart CODEC and Amp devices. It allows the connection of most Cirrus
+  Logic devices on mini-cards, as well as allowing connection of various
+  application processor systems to provide a full evaluation platform.
+  Audio system topology, clocking and power can all be controlled through
+  the Lochnagar, allowing the device under test to be used in a variety of
+  possible use cases.
+
+  This binding document describes the binding for the hardware monitor
+  portion of the driver.
+
+  This binding must be part of the Lochnagar MFD binding:
+    [1] ../mfd/cirrus,lochnagar.yaml
+
+properties:
+  compatible:
+    enum:
+      - cirrus,lochnagar2-hwmon
+
+required:
+  - compatible
+
+additionalProperties: false
diff --git a/dts/Bindings/hwmon/ti,tmp513.yaml b/dts/Bindings/hwmon/ti,tmp513.yaml
index 3f043e9436..90b2fa3f77 100644
--- a/dts/Bindings/hwmon/ti,tmp513.yaml
+++ b/dts/Bindings/hwmon/ti,tmp513.yaml
@@ -45,16 +45,14 @@ properties:
       The gain value for the PGA function. This is 8, 4, 2 or 1.
       The PGA gain affect the shunt voltage range.
       The range will be equal to: pga-gain * 40mV
-    allOf:
-      - $ref: /schemas/types.yaml#/definitions/uint32
+    $ref: /schemas/types.yaml#/definitions/uint32
     enum: [1, 2, 4, 8]
     default: 8
 
   ti,bus-range-microvolt:
     description: |
       This is the operating range of the bus voltage in microvolt
-    allOf:
-      - $ref: /schemas/types.yaml#/definitions/uint32
+    $ref: /schemas/types.yaml#/definitions/uint32
     enum: [16000000, 32000000]
     default: 32000000
 
@@ -63,14 +61,13 @@ properties:
       Array of three(TMP513) or two(TMP512) n-Factor value for each remote
       temperature channel.
       See datasheet Table 11 for n-Factor range list and value interpretation.
-    allOf:
-      - $ref: /schemas/types.yaml#definitions/uint32-array
-      - minItems: 2
-        maxItems: 3
-        items:
-          default: 0x00
-          minimum: 0x00
-          maximum: 0xFF
+    $ref: /schemas/types.yaml#definitions/uint32-array
+    minItems: 2
+    maxItems: 3
+    items:
+      default: 0x00
+      minimum: 0x00
+      maximum: 0xFF
 
 required:
   - compatible