Add devicetree source files as of Linux-3.15-rc2

This adds the Linux dts files to barebox. The dts files are
generated from Ian Campbells device-tree-rebasing.git:

git://xenbits.xen.org/people/ianc/device-tree-rebasing.git

The dts are found in dts/ in the barebox repository and
will be updated from upstream regularly, probably for each upstream
-rc.

To keep the synchronization with upstream easy no changes to
the original files are allowed under dts/. Instead changes to
upstream dts files will be done using overlays in arch/$ARCH/dts/.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

41 files changed, 1685 insertions, 0 deletions

diff --git a/dts/Bindings/i2c/brcm,bcm2835-i2c.txt b/dts/Bindings/i2c/brcm,bcm2835-i2c.txt
new file mode 100644
index 0000000000..e9de375675
--- /dev/null
+++ b/dts/Bindings/i2c/brcm,bcm2835-i2c.txt
@@ -0,0 +1,20 @@
+Broadcom BCM2835 I2C controller
+
+Required properties:
+- compatible : Should be "brcm,bcm2835-i2c".
+- reg: Should contain register location and length.
+- interrupts: Should contain interrupt.
+- clocks : The clock feeding the I2C controller.
+
+Recommended properties:
+- clock-frequency : desired I2C bus clock frequency in Hz.
+
+Example:
+
+i2c@20205000 {
+	compatible = "brcm,bcm2835-i2c";
+	reg = <0x7e205000 0x1000>;
+	interrupts = <2 21>;
+	clocks = <&clk_i2c>;
+	clock-frequency = <100000>;
+};
diff --git a/dts/Bindings/i2c/i2c-arb-gpio-challenge.txt b/dts/Bindings/i2c/i2c-arb-gpio-challenge.txt
new file mode 100644
index 0000000000..1ac8ea8ade
--- /dev/null
+++ b/dts/Bindings/i2c/i2c-arb-gpio-challenge.txt
@@ -0,0 +1,80 @@
+GPIO-based I2C Arbitration Using a Challenge & Response Mechanism
+=================================================================
+This uses GPIO lines and a challenge & response mechanism to arbitrate who is
+the master of an I2C bus in a multimaster situation.
+
+In many cases using GPIOs to arbitrate is not needed and a design can use
+the standard I2C multi-master rules.  Using GPIOs is generally useful in
+the case where there is a device on the bus that has errata and/or bugs
+that makes standard multimaster mode not feasible.
+
+
+Algorithm:
+
+All masters on the bus have a 'bus claim' line which is an output that the
+others can see. These are all active low with pull-ups enabled.  We'll
+describe these lines as:
+
+- OUR_CLAIM: output from us signaling to other hosts that we want the bus
+- THEIR_CLAIMS: output from others signaling that they want the bus
+
+The basic algorithm is to assert your line when you want the bus, then make
+sure that the other side doesn't want it also.  A detailed explanation is best
+done with an example.
+
+Let's say we want to claim the bus.  We:
+1. Assert OUR_CLAIM.
+2. Waits a little bit for the other sides to notice (slew time, say 10
+   microseconds).
+3. Check THEIR_CLAIMS.  If none are asserted then the we have the bus and we are
+   done.
+4. Otherwise, wait for a few milliseconds and see if THEIR_CLAIMS are released.
+5. If not, back off, release the claim and wait for a few more milliseconds.
+6. Go back to 1 (until retry time has expired).
+
+
+Required properties:
+- compatible: i2c-arb-gpio-challenge
+- our-claim-gpio: The GPIO that we use to claim the bus.
+- their-claim-gpios: The GPIOs that the other sides use to claim the bus.
+  Note that some implementations may only support a single other master.
+- Standard I2C mux properties. See mux.txt in this directory.
+- Single I2C child bus node at reg 0. See mux.txt in this directory.
+
+Optional properties:
+- slew-delay-us: microseconds to wait for a GPIO to go high. Default is 10 us.
+- wait-retry-us: we'll attempt another claim after this many microseconds.
+    Default is 3000 us.
+- wait-free-us: we'll give up after this many microseconds. Default is 50000 us.
+
+
+Example:
+	i2c@12CA0000 {
+		compatible = "acme,some-i2c-device";
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	i2c-arbitrator {
+		compatible = "i2c-arb-gpio-challenge";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		i2c-parent = <&{/i2c@12CA0000}>;
+
+		our-claim-gpio = <&gpf0 3 1>;
+		their-claim-gpios = <&gpe0 4 1>;
+		slew-delay-us = <10>;
+		wait-retry-us = <3000>;
+		wait-free-us = <50000>;
+
+		i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			i2c@52 {
+				// Normal I2C device
+			};
+		};
+	};
diff --git a/dts/Bindings/i2c/i2c-at91.txt b/dts/Bindings/i2c/i2c-at91.txt
new file mode 100644
index 0000000000..388f0a275f
--- /dev/null
+++ b/dts/Bindings/i2c/i2c-at91.txt
@@ -0,0 +1,34 @@
+I2C for Atmel platforms
+
+Required properties :
+- compatible : Must be "atmel,at91rm9200-i2c", "atmel,at91sam9261-i2c",
+     "atmel,at91sam9260-i2c", "atmel,at91sam9g20-i2c", "atmel,at91sam9g10-i2c"
+     or "atmel,at91sam9x5-i2c"
+- reg: physical base address of the controller and length of memory mapped
+     region.
+- interrupts: interrupt number to the cpu.
+- #address-cells = <1>;
+- #size-cells = <0>;
+- clocks: phandles to input clocks.
+
+Optional properties:
+- clock-frequency: Desired I2C bus frequency in Hz, otherwise defaults to 100000
+- Child nodes conforming to i2c bus binding
+
+Examples :
+
+i2c0: i2c@fff84000 {
+	compatible = "atmel,at91sam9g20-i2c";
+	reg = <0xfff84000 0x100>;
+	interrupts = <12 4 6>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	clocks = <&twi0_clk>;
+	clock-frequency = <400000>;
+
+	24c512@50 {
+		compatible = "24c512";
+		reg = <0x50>;
+		pagesize = <128>;
+	}
+}
diff --git a/dts/Bindings/i2c/i2c-bcm-kona.txt b/dts/Bindings/i2c/i2c-bcm-kona.txt
new file mode 100644
index 0000000000..1b87b741fa
--- /dev/null
+++ b/dts/Bindings/i2c/i2c-bcm-kona.txt
@@ -0,0 +1,35 @@
+Broadcom Kona Family I2C
+=========================
+
+This I2C controller is used in the following Broadcom SoCs:
+
+  BCM11130
+  BCM11140
+  BCM11351
+  BCM28145
+  BCM28155
+
+Required Properties
+-------------------
+- compatible: "brcm,bcm11351-i2c", "brcm,kona-i2c"
+- reg: Physical base address and length of controller registers
+- interrupts: The interrupt number used by the controller
+- clocks: clock specifier for the kona i2c external clock
+- clock-frequency: The I2C bus frequency in Hz
+- #address-cells: Should be <1>
+- #size-cells: Should be <0>
+
+Refer to clocks/clock-bindings.txt for generic clock consumer
+properties.
+
+Example:
+
+i2c@3e016000 {
+	compatible = "brcm,bcm11351-i2c","brcm,kona-i2c";
+	reg = <0x3e016000 0x80>;
+	interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+	clocks = <&bsc1_clk>;
+	clock-frequency = <400000>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+};
diff --git a/dts/Bindings/i2c/i2c-cadence.txt b/dts/Bindings/i2c/i2c-cadence.txt
new file mode 100644
index 0000000000..7cb0b5608f
--- /dev/null
+++ b/dts/Bindings/i2c/i2c-cadence.txt
@@ -0,0 +1,24 @@
+Binding for the Cadence I2C controller
+
+Required properties:
+  - reg: Physical base address and size of the controller's register area.
+  - compatible: Compatibility string. Must be 'cdns,i2c-r1p10'.
+  - clocks: Input clock specifier. Refer to common clock bindings.
+  - interrupts: Interrupt specifier. Refer to interrupt bindings.
+  - #address-cells: Should be 1.
+  - #size-cells: Should be 0.
+
+Optional properties:
+  - clock-frequency: Desired operating frequency, in Hz, of the bus.
+  - clock-names: Input clock name, should be 'pclk'.
+
+Example:
+	i2c@e0004000 {
+		compatible = "cdns,i2c-r1p10";
+		clocks = <&clkc 38>;
+		interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+		reg = <0xe0004000 0x1000>;
+		clock-frequency = <400000>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
diff --git a/dts/Bindings/i2c/i2c-cbus-gpio.txt b/dts/Bindings/i2c/i2c-cbus-gpio.txt
new file mode 100644
index 0000000000..8ce9cd2855
--- /dev/null
+++ b/dts/Bindings/i2c/i2c-cbus-gpio.txt
@@ -0,0 +1,27 @@
+Device tree bindings for i2c-cbus-gpio driver
+
+Required properties:
+	- compatible = "i2c-cbus-gpio";
+	- gpios: clk, dat, sel
+	- #address-cells = <1>;
+	- #size-cells = <0>;
+
+Optional properties:
+	- child nodes conforming to i2c bus binding
+
+Example:
+
+i2c@0 {
+	compatible = "i2c-cbus-gpio";
+	gpios = <&gpio 66 0 /* clk */
+		 &gpio 65 0 /* dat */
+		 &gpio 64 0 /* sel */
+		>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	retu-mfd: retu@1 {
+		compatible = "retu-mfd";
+		reg = <0x1>;
+	};
+};
diff --git a/dts/Bindings/i2c/i2c-davinci.txt b/dts/Bindings/i2c/i2c-davinci.txt
new file mode 100644
index 0000000000..2dc935b411
--- /dev/null
+++ b/dts/Bindings/i2c/i2c-davinci.txt
@@ -0,0 +1,28 @@
+* Texas Instruments Davinci I2C
+
+This file provides information, what the device node for the
+davinci i2c interface contain.
+
+Required properties:
+- compatible: "ti,davinci-i2c";
+- reg : Offset and length of the register set for the device
+
+Recommended properties :
+- interrupts : standard interrupt property.
+- clock-frequency : desired I2C bus clock frequency in Hz.
+
+Example (enbw_cmc board):
+	i2c@1c22000 {
+		compatible = "ti,davinci-i2c";
+		reg = <0x22000 0x1000>;
+		clock-frequency = <100000>;
+		interrupts = <15>;
+		interrupt-parent = <&intc>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		dtt@48 {
+			compatible = "national,lm75";
+			reg = <0x48>;
+		};
+	};
diff --git a/dts/Bindings/i2c/i2c-designware.txt b/dts/Bindings/i2c/i2c-designware.txt
new file mode 100644
index 0000000000..5199b0c8cf
--- /dev/null
+++ b/dts/Bindings/i2c/i2c-designware.txt
@@ -0,0 +1,45 @@
+* Synopsys DesignWare I2C
+
+Required properties :
+
+ - compatible : should be "snps,designware-i2c"
+ - reg : Offset and length of the register set for the device
+ - interrupts : <IRQ> where IRQ is the interrupt number.
+
+Recommended properties :
+
+ - clock-frequency : desired I2C bus clock frequency in Hz.
+
+Optional properties :
+ - i2c-sda-hold-time-ns : should contain the SDA hold time in nanoseconds.
+   This option is only supported in hardware blocks version 1.11a or newer.
+
+ - i2c-scl-falling-time : should contain the SCL falling time in nanoseconds.
+   This value which is by default 300ns is used to compute the tLOW period.
+
+ - i2c-sda-falling-time : should contain the SDA falling time in nanoseconds.
+   This value which is by default 300ns is used to compute the tHIGH period.
+
+Example :
+
+	i2c@f0000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,designware-i2c";
+		reg = <0xf0000 0x1000>;
+		interrupts = <11>;
+		clock-frequency = <400000>;
+	};
+
+	i2c@1120000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,designware-i2c";
+		reg = <0x1120000 0x1000>;
+		interrupt-parent = <&ictl>;
+		interrupts = <12 1>;
+		clock-frequency = <400000>;
+		i2c-sda-hold-time-ns = <300>;
+		i2c-sda-falling-time-ns = <300>;
+		i2c-scl-falling-time-ns = <300>;
+	};
diff --git a/dts/Bindings/i2c/i2c-efm32.txt b/dts/Bindings/i2c/i2c-efm32.txt
new file mode 100644
index 0000000000..fc15ac5194
--- /dev/null
+++ b/dts/Bindings/i2c/i2c-efm32.txt
@@ -0,0 +1,34 @@
+* Energymicro efm32 i2c controller
+
+Required properties :
+
+ - reg : Offset and length of the register set for the device
+ - compatible : should be "energymicro,efm32-i2c"
+ - interrupts : the interrupt number
+ - clocks : reference to the module clock
+
+Recommended properties :
+
+ - clock-frequency : maximal I2C bus clock frequency in Hz.
+ - efm32,location : Decides the location of the USART I/O pins.
+   Allowed range : [0 .. 6]
+
+Example:
+	i2c0: i2c@4000a000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "energymicro,efm32-i2c";
+		reg = <0x4000a000 0x400>;
+		interrupts = <9>;
+		clocks = <&cmu clk_HFPERCLKI2C0>;
+		clock-frequency = <100000>;
+		status = "ok";
+		efm32,location = <3>;
+
+		eeprom@50 {
+			compatible = "microchip,24c02";
+			reg = <0x50>;
+			pagesize = <16>;
+		};
+	};
+
diff --git a/dts/Bindings/i2c/i2c-exynos5.txt b/dts/Bindings/i2c/i2c-exynos5.txt
new file mode 100644
index 0000000000..056732cfdc
--- /dev/null
+++ b/dts/Bindings/i2c/i2c-exynos5.txt
@@ -0,0 +1,44 @@
+* Samsung's High Speed I2C controller
+
+The Samsung's High Speed I2C controller is used to interface with I2C devices
+at various speeds ranging from 100khz to 3.4Mhz.
+
+Required properties:
+  - compatible: value should be.
+      -> "samsung,exynos5-hsi2c", for i2c compatible with exynos5 hsi2c.
+  - reg: physical base address of the controller and length of memory mapped
+    region.
+  - interrupts: interrupt number to the cpu.
+  - #address-cells: always 1 (for i2c addresses)
+  - #size-cells: always 0
+
+  - Pinctrl:
+    - pinctrl-0: Pin control group to be used for this controller.
+    - pinctrl-names: Should contain only one value - "default".
+
+Optional properties:
+  - clock-frequency: Desired operating frequency in Hz of the bus.
+    -> If not specified, the bus operates in fast-speed mode at
+       at 100khz.
+    -> If specified, the bus operates in high-speed mode only if the
+       clock-frequency is >= 1Mhz.
+
+Example:
+
+hsi2c@12ca0000 {
+	compatible = "samsung,exynos5-hsi2c";
+	reg = <0x12ca0000 0x100>;
+	interrupts = <56>;
+	clock-frequency = <100000>;
+
+	pinctrl-0 = <&i2c4_bus>;
+	pinctrl-names = "default";
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	s2mps11_pmic@66 {
+		compatible = "samsung,s2mps11-pmic";
+		reg = <0x66>;
+	};
+};
diff --git a/dts/Bindings/i2c/i2c-gpio.txt b/dts/Bindings/i2c/i2c-gpio.txt
new file mode 100644
index 0000000000..4f8ec947c6
--- /dev/null
+++ b/dts/Bindings/i2c/i2c-gpio.txt
@@ -0,0 +1,32 @@
+Device-Tree bindings for i2c gpio driver
+
+Required properties:
+	- compatible = "i2c-gpio";
+	- gpios: sda and scl gpio
+
+
+Optional properties:
+	- i2c-gpio,sda-open-drain: sda as open drain
+	- i2c-gpio,scl-open-drain: scl as open drain
+	- i2c-gpio,scl-output-only: scl as output only
+	- i2c-gpio,delay-us: delay between GPIO operations (may depend on each platform)
+	- i2c-gpio,timeout-ms: timeout to get data
+
+Example nodes:
+
+i2c@0 {
+	compatible = "i2c-gpio";
+	gpios = <&pioA 23 0 /* sda */
+		 &pioA 24 0 /* scl */
+		>;
+	i2c-gpio,sda-open-drain;
+	i2c-gpio,scl-open-drain;
+	i2c-gpio,delay-us = <2>;	/* ~100 kHz */
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	rv3029c2@56 {
+		compatible = "rv3029c2";
+		reg = <0x56>;
+	};
+};
diff --git a/dts/Bindings/i2c/i2c-imx.txt b/dts/Bindings/i2c/i2c-imx.txt
new file mode 100644
index 0000000000..4a8513e447
--- /dev/null
+++ b/dts/Bindings/i2c/i2c-imx.txt
@@ -0,0 +1,28 @@
+* Freescale Inter IC (I2C) and High Speed Inter IC (HS-I2C) for i.MX
+
+Required properties:
+- compatible :
+  - "fsl,imx1-i2c" for I2C compatible with the one integrated on i.MX1 SoC
+  - "fsl,imx21-i2c" for I2C compatible with the one integrated on i.MX21 SoC
+  - "fsl,vf610-i2c" for I2C compatible with the one integrated on Vybrid vf610 SoC
+- reg : Should contain I2C/HS-I2C registers location and length
+- interrupts : Should contain I2C/HS-I2C interrupt
+
+Optional properties:
+- clock-frequency : Constains desired I2C/HS-I2C bus clock frequency in Hz.
+  The absence of the propoerty indicates the default frequency 100 kHz.
+
+Examples:
+
+i2c@83fc4000 { /* I2C2 on i.MX51 */
+	compatible = "fsl,imx51-i2c", "fsl,imx21-i2c";
+	reg = <0x83fc4000 0x4000>;
+	interrupts = <63>;
+};
+
+i2c@70038000 { /* HS-I2C on i.MX51 */
+	compatible = "fsl,imx51-i2c", "fsl,imx21-i2c";
+	reg = <0x70038000 0x4000>;
+	interrupts = <64>;
+	clock-frequency = <400000>;
+};
diff --git a/dts/Bindings/i2c/i2c-mpc.txt b/dts/Bindings/i2c/i2c-mpc.txt
new file mode 100644
index 0000000000..1eacd6b20e
--- /dev/null
+++ b/dts/Bindings/i2c/i2c-mpc.txt
@@ -0,0 +1,64 @@
+* I2C
+
+Required properties :
+
+ - reg : Offset and length of the register set for the device
+ - compatible : should be "fsl,CHIP-i2c" where CHIP is the name of a
+   compatible processor, e.g. mpc8313, mpc8543, mpc8544, mpc5121,
+   mpc5200 or mpc5200b. For the mpc5121, an additional node
+   "fsl,mpc5121-i2c-ctrl" is required as shown in the example below.
+
+Recommended properties :
+
+ - interrupts : <a b> where a is the interrupt number and b is a
+   field that represents an encoding of the sense and level
+   information for the interrupt.  This should be encoded based on
+   the information in section 2) depending on the type of interrupt
+   controller you have.
+ - interrupt-parent : the phandle for the interrupt controller that
+   services interrupts for this device.
+ - fsl,preserve-clocking : boolean; if defined, the clock settings
+   from the bootloader are preserved (not touched).
+ - clock-frequency : desired I2C bus clock frequency in Hz.
+ - fsl,timeout : I2C bus timeout in microseconds.
+
+Examples :
+
+	/* MPC5121 based board */
+	i2c@1740 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "fsl,mpc5121-i2c", "fsl-i2c";
+		reg = <0x1740 0x20>;
+		interrupts = <11 0x8>;
+		interrupt-parent = <&ipic>;
+		clock-frequency = <100000>;
+	};
+
+	i2ccontrol@1760 {
+		compatible = "fsl,mpc5121-i2c-ctrl";
+		reg = <0x1760 0x8>;
+	};
+
+	/* MPC5200B based board */
+	i2c@3d00 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c";
+		reg = <0x3d00 0x40>;
+		interrupts = <2 15 0>;
+		interrupt-parent = <&mpc5200_pic>;
+		fsl,preserve-clocking;
+	};
+
+	/* MPC8544 base board */
+	i2c@3100 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "fsl,mpc8544-i2c", "fsl-i2c";
+		reg = <0x3100 0x100>;
+		interrupts = <43 2>;
+		interrupt-parent = <&mpic>;
+		clock-frequency = <400000>;
+		fsl,timeout = <10000>;
+	};
diff --git a/dts/Bindings/i2c/i2c-mux-gpio.txt b/dts/Bindings/i2c/i2c-mux-gpio.txt
new file mode 100644
index 0000000000..66709a8255
--- /dev/null
+++ b/dts/Bindings/i2c/i2c-mux-gpio.txt
@@ -0,0 +1,81 @@
+GPIO-based I2C Bus Mux
+
+This binding describes an I2C bus multiplexer that uses GPIOs to
+route the I2C signals.
+
+                                  +-----+  +-----+
+                                  | dev |  | dev |
+    +------------+                +-----+  +-----+
+    | SoC        |                   |        |
+    |            |          /--------+--------+
+    |   +------+ |  +------+    child bus A, on GPIO value set to 0
+    |   | I2C  |-|--| Mux  |
+    |   +------+ |  +--+---+    child bus B, on GPIO value set to 1
+    |            |     |    \----------+--------+--------+
+    |   +------+ |     |               |        |        |
+    |   | GPIO |-|-----+            +-----+  +-----+  +-----+
+    |   +------+ |                  | dev |  | dev |  | dev |
+    +------------+                  +-----+  +-----+  +-----+
+
+Required properties:
+- compatible: i2c-mux-gpio
+- i2c-parent: The phandle of the I2C bus that this multiplexer's master-side
+  port is connected to.
+- mux-gpios: list of gpios used to control the muxer
+* Standard I2C mux properties. See mux.txt in this directory.
+* I2C child bus nodes. See mux.txt in this directory.
+
+Optional properties:
+- idle-state: value to set the muxer to when idle. When no value is
+  given, it defaults to the last value used.
+
+For each i2c child node, an I2C child bus will be created. They will
+be numbered based on their order in the device tree.
+
+Whenever an access is made to a device on a child bus, the value set
+in the revelant node's reg property will be output using the list of
+GPIOs, the first in the list holding the least-significant value.
+
+If an idle state is defined, using the idle-state (optional) property,
+whenever an access is not being made to a device on a child bus, the
+GPIOs will be set according to the idle value.
+
+If an idle state is not defined, the most recently used value will be
+left programmed into hardware whenever no access is being made to a
+device on a child bus.
+
+Example:
+	i2cmux {
+		compatible = "i2c-mux-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		mux-gpios = <&gpio1 22 0 &gpio1 23 0>;
+		i2c-parent = <&i2c1>;
+
+		i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			ssd1307: oled@3c {
+				compatible = "solomon,ssd1307fb-i2c";
+				reg = <0x3c>;
+				pwms = <&pwm 4 3000>;
+				reset-gpios = <&gpio2 7 1>;
+				reset-active-low;
+			};
+		};
+
+		i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			pca9555: pca9555@20 {
+				compatible = "nxp,pca9555";
+				gpio-controller;
+				#gpio-cells = <2>;
+				reg = <0x20>;
+			};
+		};
+	};
diff --git a/dts/Bindings/i2c/i2c-mux-pca954x.txt b/dts/Bindings/i2c/i2c-mux-pca954x.txt
new file mode 100644
index 0000000000..34a3fb6f84
--- /dev/null
+++ b/dts/Bindings/i2c/i2c-mux-pca954x.txt
@@ -0,0 +1,50 @@
+* NXP PCA954x I2C bus switch
+
+Required Properties:
+
+  - compatible: Must contain one of the following.
+    "nxp,pca9540", "nxp,pca9542", "nxp,pca9543", "nxp,pca9544",
+    "nxp,pca9545", "nxp,pca9546", "nxp,pca9547", "nxp,pca9548"
+
+  - reg: The I2C address of the device.
+
+  The following required properties are defined externally:
+
+  - Standard I2C mux properties. See i2c-mux.txt in this directory.
+  - I2C child bus nodes. See i2c-mux.txt in this directory.
+
+Optional Properties:
+
+  - reset-gpios: Reference to the GPIO connected to the reset input.
+
+
+Example:
+
+	i2c-switch@74 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x74>;
+
+		i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+
+			eeprom@54 {
+				compatible = "at,24c08";
+				reg = <0x54>;
+			};
+		};
+
+		i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+
+			rtc@51 {
+				compatible = "nxp,pcf8563";
+				reg = <0x51>;
+			};
+		};
+	};
diff --git a/dts/Bindings/i2c/i2c-mux-pinctrl.txt b/dts/Bindings/i2c/i2c-mux-pinctrl.txt
new file mode 100644
index 0000000000..ae8af1694e
--- /dev/null
+++ b/dts/Bindings/i2c/i2c-mux-pinctrl.txt
@@ -0,0 +1,93 @@
+Pinctrl-based I2C Bus Mux
+
+This binding describes an I2C bus multiplexer that uses pin multiplexing to
+route the I2C signals, and represents the pin multiplexing configuration
+using the pinctrl device tree bindings.
+
+                                 +-----+  +-----+
+                                 | dev |  | dev |
+    +------------------------+   +-----+  +-----+
+    | SoC                    |      |        |
+    |                   /----|------+--------+
+    |   +---+   +------+     | child bus A, on first set of pins
+    |   |I2C|---|Pinmux|     |
+    |   +---+   +------+     | child bus B, on second set of pins
+    |                   \----|------+--------+--------+
+    |                        |      |        |        |
+    +------------------------+  +-----+  +-----+  +-----+
+                                | dev |  | dev |  | dev |
+                                +-----+  +-----+  +-----+
+
+Required properties:
+- compatible: i2c-mux-pinctrl
+- i2c-parent: The phandle of the I2C bus that this multiplexer's master-side
+  port is connected to.
+
+Also required are:
+
+* Standard pinctrl properties that specify the pin mux state for each child
+  bus. See ../pinctrl/pinctrl-bindings.txt.
+
+* Standard I2C mux properties. See mux.txt in this directory.
+
+* I2C child bus nodes. See mux.txt in this directory.
+
+For each named state defined in the pinctrl-names property, an I2C child bus
+will be created. I2C child bus numbers are assigned based on the index into
+the pinctrl-names property.
+
+The only exception is that no bus will be created for a state named "idle". If
+such a state is defined, it must be the last entry in pinctrl-names. For
+example:
+
+	pinctrl-names = "ddc", "pta", "idle"  ->  ddc = bus 0, pta = bus 1
+	pinctrl-names = "ddc", "idle", "pta"  ->  Invalid ("idle" not last)
+	pinctrl-names = "idle", "ddc", "pta"  ->  Invalid ("idle" not last)
+
+Whenever an access is made to a device on a child bus, the relevant pinctrl
+state will be programmed into hardware.
+
+If an idle state is defined, whenever an access is not being made to a device
+on a child bus, the idle pinctrl state will be programmed into hardware.
+
+If an idle state is not defined, the most recently used pinctrl state will be
+left programmed into hardware whenever no access is being made of a device on
+a child bus.
+
+Example:
+
+	i2cmux {
+		compatible = "i2c-mux-pinctrl";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		i2c-parent = <&i2c1>;
+
+		pinctrl-names = "ddc", "pta", "idle";
+		pinctrl-0 = <&state_i2cmux_ddc>;
+		pinctrl-1 = <&state_i2cmux_pta>;
+		pinctrl-2 = <&state_i2cmux_idle>;
+
+		i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			eeprom {
+				compatible = "eeprom";
+				reg = <0x50>;
+			};
+		};
+
+		i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			eeprom {
+				compatible = "eeprom";
+				reg = <0x50>;
+			};
+		};
+	};
+
diff --git a/dts/Bindings/i2c/i2c-mux.txt b/dts/Bindings/i2c/i2c-mux.txt
new file mode 100644
index 0000000000..af84cce5cd
--- /dev/null
+++ b/dts/Bindings/i2c/i2c-mux.txt
@@ -0,0 +1,60 @@
+Common i2c bus multiplexer/switch properties.
+
+An i2c bus multiplexer/switch will have several child busses that are
+numbered uniquely in a device dependent manner.  The nodes for an i2c bus
+multiplexer/switch will have one child node for each child
+bus.
+
+Required properties:
+- #address-cells = <1>;
+- #size-cells = <0>;
+
+Required properties for child nodes:
+- #address-cells = <1>;
+- #size-cells = <0>;
+- reg : The sub-bus number.
+
+Optional properties for child nodes:
+- Other properties specific to the multiplexer/switch hardware.
+- Child nodes conforming to i2c bus binding
+
+
+Example :
+
+	/*
+	   An NXP pca9548 8 channel I2C multiplexer at address 0x70
+	   with two NXP pca8574 GPIO expanders attached, one each to
+	   ports 3 and 4.
+	 */
+
+	mux@70 {
+		compatible = "nxp,pca9548";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+
+			gpio1: gpio@38 {
+				compatible = "nxp,pca8574";
+				reg = <0x38>;
+				#gpio-cells = <2>;
+				gpio-controller;
+			};
+		};
+		i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+
+			gpio2: gpio@38 {
+				compatible = "nxp,pca8574";
+				reg = <0x38>;
+				#gpio-cells = <2>;
+				gpio-controller;
+			};
+		};
+	};
diff --git a/dts/Bindings/i2c/i2c-mv64xxx.txt b/dts/Bindings/i2c/i2c-mv64xxx.txt
new file mode 100644
index 0000000000..befd4fb476
--- /dev/null
+++ b/dts/Bindings/i2c/i2c-mv64xxx.txt
@@ -0,0 +1,44 @@
+
+* Marvell MV64XXX I2C controller
+
+Required properties :
+
+ - reg             : Offset and length of the register set for the device
+ - compatible      : Should be either:
+                     - "allwinner,sun4i-i2c"
+                     - "allwinner,sun6i-a31-i2c"
+                     - "marvell,mv64xxx-i2c"
+                     - "marvell,mv78230-i2c"
+                     - "marvell,mv78230-a0-i2c"
+                       * Note: Only use "marvell,mv78230-a0-i2c" for a
+                         very rare, initial version of the SoC which
+                         had broken offload support.  Linux
+                         auto-detects this and sets it appropriately.
+ - interrupts      : The interrupt number
+
+Optional properties :
+
+ - clock-frequency : Desired I2C bus clock frequency in Hz. If not set the
+default frequency is 100kHz
+
+ - resets          : phandle to the parent reset controller. Mandatory
+                     whenever you're using the "allwinner,sun6i-a31-i2c"
+                     compatible.
+
+Examples:
+
+	i2c@11000 {
+		compatible = "marvell,mv64xxx-i2c";
+		reg = <0x11000 0x20>;
+		interrupts = <29>;
+		clock-frequency = <100000>;
+	};
+
+For the Armada XP:
+
+	i2c@11000 {
+		compatible = "marvell,mv78230-i2c", "marvell,mv64xxx-i2c";
+		reg = <0x11000 0x100>;
+		interrupts = <29>;
+		clock-frequency = <100000>;
+	};
diff --git a/dts/Bindings/i2c/i2c-mxs.txt b/dts/Bindings/i2c/i2c-mxs.txt
new file mode 100644
index 0000000000..4e1c8ac01e
--- /dev/null
+++ b/dts/Bindings/i2c/i2c-mxs.txt
@@ -0,0 +1,25 @@
+* Freescale MXS Inter IC (I2C) Controller
+
+Required properties:
+- compatible: Should be "fsl,<chip>-i2c"
+- reg: Should contain registers location and length
+- interrupts: Should contain ERROR interrupt number
+- clock-frequency: Desired I2C bus clock frequency in Hz.
+                   Only 100000Hz and 400000Hz modes are supported.
+- dmas: DMA specifier, consisting of a phandle to DMA controller node
+  and I2C DMA channel ID.
+  Refer to dma.txt and fsl-mxs-dma.txt for details.
+- dma-names: Must be "rx-tx".
+
+Examples:
+
+i2c0: i2c@80058000 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	compatible = "fsl,imx28-i2c";
+	reg = <0x80058000 2000>;
+	interrupts = <111>;
+	clock-frequency = <100000>;
+	dmas = <&dma_apbx 6>;
+	dma-names = "rx-tx";
+};
diff --git a/dts/Bindings/i2c/i2c-nomadik.txt b/dts/Bindings/i2c/i2c-nomadik.txt
new file mode 100644
index 0000000000..72065b0ff6
--- /dev/null
+++ b/dts/Bindings/i2c/i2c-nomadik.txt
@@ -0,0 +1,23 @@
+I2C for Nomadik based systems
+
+Required (non-standard) properties:
+ - Nil
+
+Recommended (non-standard) properties:
+ - clock-frequency : Maximum bus clock frequency for the device
+
+Optional (non-standard) properties:
+ - Nil
+
+Example :
+
+i2c@80004000 {
+        compatible = "stericsson,db8500-i2c", "st,nomadik-i2c";
+        reg = <0x80004000 0x1000>;
+        interrupts = <0 21 0x4>;
+        #address-cells = <1>;
+        #size-cells = <0>;
+        v-i2c-supply = <&db8500_vape_reg>;
+
+        clock-frequency = <400000>;
+};
diff --git a/dts/Bindings/i2c/i2c-ocores.txt b/dts/Bindings/i2c/i2c-ocores.txt
new file mode 100644
index 0000000000..1637c298a1
--- /dev/null
+++ b/dts/Bindings/i2c/i2c-ocores.txt
@@ -0,0 +1,33 @@
+Device tree configuration for i2c-ocores
+
+Required properties:
+- compatible      : "opencores,i2c-ocores" or "aeroflexgaisler,i2cmst"
+- reg             : bus address start and address range size of device
+- interrupts      : interrupt number
+- clock-frequency : frequency of bus clock in Hz
+- #address-cells  : should be <1>
+- #size-cells     : should be <0>
+
+Optional properties:
+- reg-shift       : device register offsets are shifted by this value
+- reg-io-width    : io register width in bytes (1, 2 or 4)
+- regstep         : deprecated, use reg-shift above
+
+Example:
+
+	i2c0: ocores@a0000000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "opencores,i2c-ocores";
+		reg = <0xa0000000 0x8>;
+		interrupts = <10>;
+		clock-frequency = <20000000>;
+
+		reg-shift = <0>;	/* 8 bit registers */
+		reg-io-width = <1>;	/* 8 bit read/write */
+
+		dummy@60 {
+			compatible = "dummy";
+			reg = <0x60>;
+		};
+	};
diff --git a/dts/Bindings/i2c/i2c-octeon.txt b/dts/Bindings/i2c/i2c-octeon.txt
new file mode 100644
index 0000000000..dced82ebe3
--- /dev/null
+++ b/dts/Bindings/i2c/i2c-octeon.txt
@@ -0,0 +1,34 @@
+* Two Wire Serial Interface (TWSI) / I2C
+
+- compatible: "cavium,octeon-3860-twsi"
+
+  Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
+
+- reg: The base address of the TWSI/I2C bus controller register bank.
+
+- #address-cells: Must be <1>.
+
+- #size-cells: Must be <0>.  I2C addresses have no size component.
+
+- interrupts: A single interrupt specifier.
+
+- clock-frequency: The I2C bus clock rate in Hz.
+
+Example:
+	twsi0: i2c@1180000001000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "cavium,octeon-3860-twsi";
+		reg = <0x11800 0x00001000 0x0 0x200>;
+		interrupts = <0 45>;
+		clock-frequency = <100000>;
+
+		rtc@68 {
+			compatible = "dallas,ds1337";
+			reg = <0x68>;
+		};
+		tmp@4c {
+			compatible = "ti,tmp421";
+			reg = <0x4c>;
+		};
+	};
diff --git a/dts/Bindings/i2c/i2c-omap.txt b/dts/Bindings/i2c/i2c-omap.txt
new file mode 100644
index 0000000000..7e49839d41
--- /dev/null
+++ b/dts/Bindings/i2c/i2c-omap.txt
@@ -0,0 +1,31 @@
+I2C for OMAP platforms
+
+Required properties :
+- compatible : Must be "ti,omap2420-i2c", "ti,omap2430-i2c", "ti,omap3-i2c"
+  or "ti,omap4-i2c"
+- ti,hwmods : Must be "i2c<n>", n being the instance number (1-based)
+- #address-cells = <1>;
+- #size-cells = <0>;
+
+Recommended properties :
+- clock-frequency : Desired I2C bus clock frequency in Hz. Otherwise
+  the default 100 kHz frequency will be used.
+
+Optional properties:
+- Child nodes conforming to i2c bus binding
+
+Note: Current implementation will fetch base address, irq and dma
+from omap hwmod data base during device registration.
+Future plan is to migrate hwmod data base contents into device tree
+blob so that, all the required data will be used from device tree dts
+file.
+
+Examples :
+
+i2c1: i2c@0 {
+    compatible = "ti,omap3-i2c";
+    #address-cells = <1>;
+    #size-cells = <0>;
+    ti,hwmods = "i2c1";
+    clock-frequency = <400000>;
+};
diff --git a/dts/Bindings/i2c/i2c-pnx.txt b/dts/Bindings/i2c/i2c-pnx.txt
new file mode 100644
index 0000000000..fe98ada33e
--- /dev/null
+++ b/dts/Bindings/i2c/i2c-pnx.txt
@@ -0,0 +1,36 @@
+* NXP PNX I2C Controller
+
+Required properties:
+
+ - reg: Offset and length of the register set for the device
+ - compatible: should be "nxp,pnx-i2c"
+ - interrupts: configure one interrupt line
+ - #address-cells: always 1 (for i2c addresses)
+ - #size-cells: always 0
+ - interrupt-parent: the phandle for the interrupt controller that
+   services interrupts for this device.
+
+Optional properties:
+
+ - clock-frequency: desired I2C bus clock frequency in Hz, Default: 100000 Hz
+
+Examples:
+
+	i2c1: i2c@400a0000 {
+		compatible = "nxp,pnx-i2c";
+		reg = <0x400a0000 0x100>;
+		interrupt-parent = <&mic>;
+		interrupts = <51 0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	i2c2: i2c@400a8000 {
+		compatible = "nxp,pnx-i2c";
+		reg = <0x400a8000 0x100>;
+		interrupt-parent = <&mic>;
+		interrupts = <50 0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clock-frequency = <100000>;
+	};
diff --git a/dts/Bindings/i2c/i2c-pxa-pci-ce4100.txt b/dts/Bindings/i2c/i2c-pxa-pci-ce4100.txt
new file mode 100644
index 0000000000..569b162485
--- /dev/null
+++ b/dts/Bindings/i2c/i2c-pxa-pci-ce4100.txt
@@ -0,0 +1,93 @@
+CE4100 I2C
+----------
+
+CE4100 has one PCI device which is described as the I2C-Controller. This
+PCI device has three PCI-bars, each bar contains a complete I2C
+controller. So we have a total of three independent I2C-Controllers
+which share only an interrupt line.
+The driver is probed via the PCI-ID and is gathering the information of
+attached devices from the devices tree.
+Grant Likely recommended to use the ranges property to map the PCI-Bar
+number to its physical address and to use this to find the child nodes
+of the specific I2C controller. This were his exact words:
+
+       Here's where the magic happens.  Each entry in
+       ranges describes how the parent pci address space
+       (middle group of 3) is translated to the local
+       address space (first group of 2) and the size of
+       each range (last cell).  In this particular case,
+       the first cell of the local address is chosen to be
+       1:1 mapped to the BARs, and the second is the
+       offset from be base of the BAR (which would be
+       non-zero if you had 2 or more devices mapped off
+       the same BAR)
+
+       ranges allows the address mapping to be described
+       in a way that the OS can interpret without
+       requiring custom device driver code.
+
+This is an example which is used on FalconFalls:
+------------------------------------------------
+	i2c-controller@b,2 {
+		#address-cells = <2>;
+		#size-cells = <1>;
+		compatible = "pci8086,2e68.2",
+				"pci8086,2e68",
+				"pciclass,ff0000",
+				"pciclass,ff00";
+
+		reg = <0x15a00 0x0 0x0 0x0 0x0>;
+		interrupts = <16 1>;
+
+		/* as described by Grant, the first number in the group of
+		* three is the bar number followed by the 64bit bar address
+		* followed by size of the mapping. The bar address
+		* requires also a valid translation in parents ranges
+		* property.
+		*/
+		ranges = <0 0   0x02000000 0 0xdffe0500 0x100
+			  1 0   0x02000000 0 0xdffe0600 0x100
+			  2 0   0x02000000 0 0xdffe0700 0x100>;
+
+		i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "intel,ce4100-i2c-controller";
+
+			/* The first number in the reg property is the
+			* number of the bar
+			*/
+			reg = <0 0 0x100>;
+
+			/* This I2C controller has no devices */
+		};
+
+		i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "intel,ce4100-i2c-controller";
+			reg = <1 0 0x100>;
+
+			/* This I2C controller has one gpio controller */
+			gpio@26 {
+				#gpio-cells = <2>;
+				compatible = "ti,pcf8575";
+				reg = <0x26>;
+				gpio-controller;
+			};
+		};
+
+		i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "intel,ce4100-i2c-controller";
+			reg = <2 0 0x100>;
+
+			gpio@26 {
+				#gpio-cells = <2>;
+				compatible = "ti,pcf8575";
+				reg = <0x26>;
+				gpio-controller;
+			};
+		};
+	};
diff --git a/dts/Bindings/i2c/i2c-pxa.txt b/dts/Bindings/i2c/i2c-pxa.txt
new file mode 100644
index 0000000000..12b78ac507
--- /dev/null
+++ b/dts/Bindings/i2c/i2c-pxa.txt
@@ -0,0 +1,33 @@
+* Marvell MMP I2C controller
+
+Required properties :
+
+ - reg : Offset and length of the register set for the device
+ - compatible : should be "mrvl,mmp-twsi" where mmp is the name of a
+   compatible processor, e.g. pxa168, pxa910, mmp2, mmp3.
+   For the pxa2xx/pxa3xx, an additional node "mrvl,pxa-i2c" is required
+   as shown in the example below.
+
+Recommended properties :
+
+ - interrupts : the interrupt number
+ - interrupt-parent : the phandle for the interrupt controller that
+   services interrupts for this device. If the parent is the default
+   interrupt controller in device tree, it could be ignored.
+ - mrvl,i2c-polling : Disable interrupt of i2c controller. Polling
+   status register of i2c controller instead.
+ - mrvl,i2c-fast-mode : Enable fast mode of i2c controller.
+
+Examples:
+	twsi1: i2c@d4011000 {
+		compatible = "mrvl,mmp-twsi";
+		reg = <0xd4011000 0x1000>;
+		interrupts = <7>;
+		mrvl,i2c-fast-mode;
+	};
+	
+	twsi2: i2c@d4025000 {
+		compatible = "mrvl,mmp-twsi";
+		reg = <0xd4025000 0x1000>;
+		interrupts = <58>;
+	};
diff --git a/dts/Bindings/i2c/i2c-rcar.txt b/dts/Bindings/i2c/i2c-rcar.txt
new file mode 100644
index 0000000000..dd8b2dd1ed
--- /dev/null
+++ b/dts/Bindings/i2c/i2c-rcar.txt
@@ -0,0 +1,29 @@
+I2C for R-Car platforms
+
+Required properties:
+- compatible: Must be one of
+	"renesas,i2c-rcar"
+	"renesas,i2c-r8a7778"
+	"renesas,i2c-r8a7779"
+	"renesas,i2c-r8a7790"
+	"renesas,i2c-r8a7791"
+- reg: physical base address of the controller and length of memory mapped
+  region.
+- interrupts: interrupt specifier.
+
+Optional properties:
+- clock-frequency: desired I2C bus clock frequency in Hz. The absence of this
+  propoerty indicates the default frequency 100 kHz.
+- clocks: clock specifier.
+
+Examples :
+
+i2c0: i2c@e6508000 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	compatible = "renesas,i2c-r8a7791";
+	reg = <0 0xe6508000 0 0x40>;
+	interrupts = <0 287 IRQ_TYPE_LEVEL_HIGH>;
+	clocks = <&mstp9_clks R8A7791_CLK_I2C0>;
+	clock-frequency = <400000>;
+};
diff --git a/dts/Bindings/i2c/i2c-riic.txt b/dts/Bindings/i2c/i2c-riic.txt
new file mode 100644
index 0000000000..0bcc4716c3
--- /dev/null
+++ b/dts/Bindings/i2c/i2c-riic.txt
@@ -0,0 +1,29 @@
+Device tree configuration for Renesas RIIC driver
+
+Required properties:
+- compatible      : "renesas,riic-<soctype>". "renesas,riic-rz" as fallback
+- reg             : address start and address range size of device
+- interrupts      : 8 interrupts (TEI, RI, TI, SPI, STI, NAKI, ALI, TMOI)
+- clock-frequency : frequency of bus clock in Hz
+- #address-cells  : should be <1>
+- #size-cells     : should be <0>
+
+Pinctrl properties might be needed, too. See there.
+
+Example:
+
+	i2c0: i2c@fcfee000 {
+		compatible = "renesas,riic-r7s72100", "renesas,riic-rz";
+		reg = <0xfcfee000 0x44>;
+		interrupts = <0 157 IRQ_TYPE_LEVEL_HIGH>,
+			     <0 158 IRQ_TYPE_EDGE_RISING>,
+			     <0 159 IRQ_TYPE_EDGE_RISING>,
+			     <0 160 IRQ_TYPE_LEVEL_HIGH>,
+			     <0 161 IRQ_TYPE_LEVEL_HIGH>,
+			     <0 162 IRQ_TYPE_LEVEL_HIGH>,
+			     <0 163 IRQ_TYPE_LEVEL_HIGH>,
+			     <0 164 IRQ_TYPE_LEVEL_HIGH>;
+		clock-frequency = <100000>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
diff --git a/dts/Bindings/i2c/i2c-s3c2410.txt b/dts/Bindings/i2c/i2c-s3c2410.txt
new file mode 100644
index 0000000000..278de8e64b
--- /dev/null
+++ b/dts/Bindings/i2c/i2c-s3c2410.txt
@@ -0,0 +1,59 @@
+* Samsung's I2C controller
+
+The Samsung's I2C controller is used to interface with I2C devices.
+
+Required properties:
+  - compatible: value should be either of the following.
+      (a) "samsung, s3c2410-i2c", for i2c compatible with s3c2410 i2c.
+      (b) "samsung, s3c2440-i2c", for i2c compatible with s3c2440 i2c.
+      (c) "samsung, s3c2440-hdmiphy-i2c", for s3c2440-like i2c used
+          inside HDMIPHY block found on several samsung SoCs
+      (d) "samsung, exynos5440-i2c", for s3c2440-like i2c used
+	   on EXYNOS5440 which does not need GPIO configuration.
+      (e) "samsung, exynos5-sata-phy-i2c", for s3c2440-like i2c used as
+	   a host to SATA PHY controller on an internal bus.
+  - reg: physical base address of the controller and length of memory mapped
+    region.
+  - interrupts: interrupt number to the cpu.
+  - samsung,i2c-sda-delay: Delay (in ns) applied to data line (SDA) edges.
+
+Required for all cases except "samsung,s3c2440-hdmiphy-i2c":
+  - Samsung GPIO variant (deprecated):
+    - gpios: The order of the gpios should be the following: <SDA, SCL>.
+      The gpio specifier depends on the gpio controller. Required in all
+      cases except for "samsung,s3c2440-hdmiphy-i2c" whose input/output
+      lines are permanently wired to the respective clienta
+  - Pinctrl variant (preferred, if available):
+    - pinctrl-0: Pin control group to be used for this controller.
+    - pinctrl-names: Should contain only one value - "default".
+
+Optional properties:
+  - samsung,i2c-slave-addr: Slave address in multi-master environment. If not
+    specified, default value is 0.
+  - samsung,i2c-max-bus-freq: Desired frequency in Hz of the bus. If not
+    specified, the default value in Hz is 100000.
+
+Example:
+
+	i2c@13870000 {
+		compatible = "samsung,s3c2440-i2c";
+		reg = <0x13870000 0x100>;
+		interrupts = <345>;
+		samsung,i2c-sda-delay = <100>;
+		samsung,i2c-max-bus-freq = <100000>;
+		/* Samsung GPIO variant begins here */
+		gpios = <&gpd1 2 0 /* SDA */
+			 &gpd1 3 0 /* SCL */>;
+		/* Samsung GPIO variant ends here */
+		/* Pinctrl variant begins here */
+		pinctrl-0 = <&i2c3_bus>;
+		pinctrl-names = "default";
+		/* Pinctrl variant ends here */
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		wm8994@1a {
+			compatible = "wlf,wm8994";
+			reg = <0x1a>;
+		};
+	};
diff --git a/dts/Bindings/i2c/i2c-sirf.txt b/dts/Bindings/i2c/i2c-sirf.txt
new file mode 100644
index 0000000000..7baf9e133f
--- /dev/null
+++ b/dts/Bindings/i2c/i2c-sirf.txt
@@ -0,0 +1,19 @@
+I2C for SiRFprimaII platforms
+
+Required properties :
+- compatible : Must be "sirf,prima2-i2c"
+- reg: physical base address of the controller and length of memory mapped
+     region.
+- interrupts: interrupt number to the cpu.
+
+Optional properties:
+- clock-frequency : Constains desired I2C/HS-I2C bus clock frequency in Hz.
+  The absence of the propoerty indicates the default frequency 100 kHz.
+
+Examples :
+
+i2c0: i2c@b00e0000 {
+    compatible = "sirf,prima2-i2c";
+    reg = <0xb00e0000 0x10000>;
+    interrupts = <24>;
+};
diff --git a/dts/Bindings/i2c/i2c-st-ddci2c.txt b/dts/Bindings/i2c/i2c-st-ddci2c.txt
new file mode 100644
index 0000000000..bd81a48263
--- /dev/null
+++ b/dts/Bindings/i2c/i2c-st-ddci2c.txt
@@ -0,0 +1,15 @@
+ST Microelectronics DDC I2C
+
+Required properties :
+- compatible : Must be "st,ddci2c"
+- reg: physical base address of the controller and length of memory mapped
+     region.
+- interrupts: interrupt number to the cpu.
+- #address-cells = <1>;
+- #size-cells = <0>;
+
+Optional properties:
+- Child nodes conforming to i2c bus binding
+
+Examples :
+
diff --git a/dts/Bindings/i2c/i2c-st.txt b/dts/Bindings/i2c/i2c-st.txt
new file mode 100644
index 0000000000..437e0db382
--- /dev/null
+++ b/dts/Bindings/i2c/i2c-st.txt
@@ -0,0 +1,41 @@
+ST SSC binding, for I2C mode operation
+
+Required properties :
+- compatible : Must be "st,comms-ssc-i2c" or "st,comms-ssc4-i2c"
+- reg : Offset and length of the register set for the device
+- interrupts : the interrupt specifier
+- clock-names: Must contain "ssc".
+- clocks: Must contain an entry for each name in clock-names. See the common
+  clock bindings.
+- A pinctrl state named "default" must be defined to set pins in mode of
+  operation for I2C transfer.
+
+Optional properties :
+- clock-frequency : Desired I2C bus clock frequency in Hz. If not specified,
+  the default 100 kHz frequency will be used. As only Normal and Fast modes
+  are supported, possible values are 100000 and 400000.
+- st,i2c-min-scl-pulse-width-us : The minimum valid SCL pulse width that is
+  allowed through the deglitch circuit. In units of us.
+- st,i2c-min-sda-pulse-width-us : The minimum valid SDA pulse width that is
+  allowed through the deglitch circuit. In units of us.
+- A pinctrl state named "idle" could be defined to set pins in idle state
+  when I2C instance is not performing a transfer.
+- A pinctrl state named "sleep" could be defined to set pins in sleep state
+  when driver enters in suspend.
+
+
+
+Example :
+
+i2c0: i2c@fed40000 {
+	compatible	= "st,comms-ssc4-i2c";
+	reg		= <0xfed40000 0x110>;
+	interrupts	=  <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>;
+	clocks		= <&CLK_S_ICN_REG_0>;
+	clock-names	= "ssc";
+	clock-frequency = <400000>;
+	pinctrl-names	= "default";
+	pinctrl-0	= <&pinctrl_i2c0_default>;
+	st,i2c-min-scl-pulse-width-us = <0>;
+	st,i2c-min-sda-pulse-width-us = <5>;
+};
diff --git a/dts/Bindings/i2c/i2c-versatile.txt b/dts/Bindings/i2c/i2c-versatile.txt
new file mode 100644
index 0000000000..361d31c51b
--- /dev/null
+++ b/dts/Bindings/i2c/i2c-versatile.txt
@@ -0,0 +1,10 @@
+i2c Controller on ARM Versatile platform:
+
+Required properties:
+- compatible : Must be "arm,versatile-i2c";
+- reg
+- #address-cells = <1>;
+- #size-cells = <0>;
+
+Optional properties:
+- Child nodes conforming to i2c bus binding
diff --git a/dts/Bindings/i2c/i2c-vt8500.txt b/dts/Bindings/i2c/i2c-vt8500.txt
new file mode 100644
index 0000000000..94a425eaa6
--- /dev/null
+++ b/dts/Bindings/i2c/i2c-vt8500.txt
@@ -0,0 +1,24 @@
+* Wondermedia I2C Controller
+
+Required properties :
+
+ - compatible : should be "wm,wm8505-i2c"
+ - reg : Offset and length of the register set for the device
+ - interrupts : <IRQ> where IRQ is the interrupt number
+ - clocks : phandle to the I2C clock source
+
+Optional properties :
+
+ - clock-frequency : desired I2C bus clock frequency in Hz.
+	Valid values are 100000 and 400000.
+	Default to 100000 if not specified, or invalid value.
+
+Example :
+
+	i2c_0: i2c@d8280000 {
+		compatible = "wm,wm8505-i2c";
+		reg = <0xd8280000 0x1000>;
+		interrupts = <19>;
+		clocks = <&clki2c0>;
+		clock-frequency = <400000>;
+	};
diff --git a/dts/Bindings/i2c/i2c-xiic.txt b/dts/Bindings/i2c/i2c-xiic.txt
new file mode 100644
index 0000000000..ceabbe91ae
--- /dev/null
+++ b/dts/Bindings/i2c/i2c-xiic.txt
@@ -0,0 +1,22 @@
+Xilinx IIC controller:
+
+Required properties:
+- compatible : Must be "xlnx,xps-iic-2.00.a"
+- reg : IIC register location and length
+- interrupts : IIC controller unterrupt
+- #address-cells = <1>
+- #size-cells = <0>
+
+Optional properties:
+- Child nodes conforming to i2c bus binding
+
+Example:
+
+	axi_iic_0: i2c@40800000 {
+		compatible = "xlnx,xps-iic-2.00.a";
+		interrupts = < 1 2 >;
+		reg = < 0x40800000 0x10000 >;
+
+		#size-cells = <0>;
+		#address-cells = <1>;
+	};
diff --git a/dts/Bindings/i2c/ina209.txt b/dts/Bindings/i2c/ina209.txt
new file mode 100644
index 0000000000..9dd2bee808
--- /dev/null
+++ b/dts/Bindings/i2c/ina209.txt
@@ -0,0 +1,18 @@
+ina209 properties
+
+Required properties:
+- compatible: Must be "ti,ina209"
+- reg: I2C address
+
+Optional properties:
+
+- shunt-resistor
+	Shunt resistor value in micro-Ohm
+
+Example:
+
+temp-sensor@4c {
+	compatible = "ti,ina209";
+	reg = <0x4c>;
+	shunt-resistor = <5000>;
+};
diff --git a/dts/Bindings/i2c/ina2xx.txt b/dts/Bindings/i2c/ina2xx.txt
new file mode 100644
index 0000000000..a2ad85d7e7
--- /dev/null
+++ b/dts/Bindings/i2c/ina2xx.txt
@@ -0,0 +1,22 @@
+ina2xx properties
+
+Required properties:
+- compatible: Must be one of the following:
+	- "ti,ina219" for ina219
+	- "ti,ina220" for ina220
+	- "ti,ina226" for ina226
+	- "ti,ina230" for ina230
+- reg: I2C address
+
+Optional properties:
+
+- shunt-resistor
+	Shunt resistor value in micro-Ohm
+
+Example:
+
+ina220@44 {
+	compatible = "ti,ina220";
+	reg = <0x44>;
+	shunt-resistor = <1000>;
+};
diff --git a/dts/Bindings/i2c/max6697.txt b/dts/Bindings/i2c/max6697.txt
new file mode 100644
index 0000000000..5f793998e4
--- /dev/null
+++ b/dts/Bindings/i2c/max6697.txt
@@ -0,0 +1,64 @@
+max6697 properties
+
+Required properties:
+- compatible:
+	Should be one of
+		maxim,max6581
+		maxim,max6602
+		maxim,max6622
+		maxim,max6636
+		maxim,max6689
+		maxim,max6693
+		maxim,max6694
+		maxim,max6697
+		maxim,max6698
+		maxim,max6699
+- reg: I2C address
+
+Optional properties:
+
+- smbus-timeout-disable
+	Set to disable SMBus timeout. If not specified, SMBus timeout will be
+	enabled.
+- extended-range-enable
+	Only valid for MAX6581. Set to enable extended temperature range.
+	Extended temperature will be disabled if not specified.
+- beta-compensation-enable
+	Only valid for MAX6693 and MX6694. Set to enable beta compensation on
+	remote temperature channel 1.
+	Beta compensation will be disabled if not specified.
+- alert-mask
+	Alert bit mask. Alert disabled for bits set.
+	Select bit 0 for local temperature, bit 1..7 for remote temperatures.
+	If not specified, alert will be enabled for all channels.
+- over-temperature-mask
+	Over-temperature bit mask. Over-temperature reporting disabled for
+	bits set.
+	Select bit 0 for local temperature, bit 1..7 for remote temperatures.
+	If not specified, over-temperature reporting will be enabled for all
+	channels.
+- resistance-cancellation
+	Boolean for all chips other than MAX6581. Set to enable resistance
+	cancellation on remote temperature channel 1.
+	For MAX6581, resistance cancellation enabled for all channels if
+	specified as boolean, otherwise as per bit mask specified.
+	Only supported for remote temperatures (bit 1..7).
+	If not specified, resistance cancellation will be disabled for all
+	channels.
+- transistor-ideality
+	For MAX6581 only. Two values; first is bit mask, second is ideality
+	select value as per MAX6581 data sheet. Select bit 1..7 for remote
+	channels.
+	Transistor ideality will be initialized to default (1.008) if not
+	specified.
+
+Example:
+
+temp-sensor@1a {
+	compatible = "maxim,max6697";
+	reg = <0x1a>;
+	smbus-timeout-disable;
+	resistance-cancellation;
+	alert-mask = <0x72>;
+	over-temperature-mask = <0x7f>;
+};
diff --git a/dts/Bindings/i2c/nvidia,tegra20-i2c.txt b/dts/Bindings/i2c/nvidia,tegra20-i2c.txt
new file mode 100644
index 0000000000..87507e9ce6
--- /dev/null
+++ b/dts/Bindings/i2c/nvidia,tegra20-i2c.txt
@@ -0,0 +1,75 @@
+NVIDIA Tegra20/Tegra30/Tegra114 I2C controller driver.
+
+Required properties:
+- compatible : should be:
+	"nvidia,tegra114-i2c"
+	"nvidia,tegra30-i2c"
+	"nvidia,tegra20-i2c"
+	"nvidia,tegra20-i2c-dvc"
+  Details of compatible are as follows:
+  nvidia,tegra20-i2c-dvc: Tegra20 has specific I2C controller called as DVC I2C
+	controller. This only support master mode of I2C communication. Register
+	interface/offset and interrupts handling are different than generic I2C
+	controller. Driver of DVC I2C controller is only compatible with
+	"nvidia,tegra20-i2c-dvc".
+  nvidia,tegra20-i2c: Tegra20 has 4 generic I2C controller. This can support
+	master and slave mode of I2C communication. The i2c-tegra driver only
+	support master mode of I2C communication. Driver of I2C controller is
+	only compatible with "nvidia,tegra20-i2c".
+  nvidia,tegra30-i2c: Tegra30 has 5 generic I2C controller. This controller is
+	very much similar to Tegra20 I2C controller with additional feature:
+	Continue Transfer Support. This feature helps to implement M_NO_START
+	as per I2C core API transfer flags. Driver of I2C controller is
+	compatible with "nvidia,tegra30-i2c" to enable the continue transfer
+	support. This is also compatible with "nvidia,tegra20-i2c" without
+	continue transfer support.
+  nvidia,tegra114-i2c: Tegra114 has 5 generic I2C controller. This controller is
+	very much similar to Tegra30 I2C controller with some hardware
+	modification:
+	 - Tegra30/Tegra20 I2C controller has 2 clock source called div-clk and
+	   fast-clk. Tegra114 has only one clock source called as div-clk and
+	   hence clock mechanism is changed in I2C controller.
+	 - Tegra30/Tegra20 I2C controller has enabled per packet transfer by
+	   default and there is no way to disable it. Tegra114 has this
+	   interrupt disable by default and SW need to enable explicitly.
+	Due to above changes, Tegra114 I2C driver makes incompatible with
+	previous hardware driver. Hence, tegra114 I2C controller is compatible
+	with "nvidia,tegra114-i2c".
+- reg: Should contain I2C controller registers physical address and length.
+- interrupts: Should contain I2C controller interrupts.
+- address-cells: Address cells for I2C device address.
+- size-cells: Size of the I2C device address.
+- clocks: Must contain an entry for each entry in clock-names.
+  See ../clocks/clock-bindings.txt for details.
+- clock-names: Must include the following entries:
+  Tegra20/Tegra30:
+  - div-clk
+  - fast-clk
+  Tegra114:
+  - div-clk
+- resets: Must contain an entry for each entry in reset-names.
+  See ../reset/reset.txt for details.
+- reset-names: Must include the following entries:
+  - i2c
+- dmas: Must contain an entry for each entry in clock-names.
+  See ../dma/dma.txt for details.
+- dma-names: Must include the following entries:
+  - rx
+  - tx
+
+Example:
+
+	i2c@7000c000 {
+		compatible = "nvidia,tegra20-i2c";
+		reg = <0x7000c000 0x100>;
+		interrupts = <0 38 0x04>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&tegra_car 12>, <&tegra_car 124>;
+		clock-names = "div-clk", "fast-clk";
+		resets = <&tegra_car 12>;
+		reset-names = "i2c";
+		dmas = <&apbdma 16>, <&apbdma 16>;
+		dma-names = "rx", "tx";
+		status = "disabled";
+	};
diff --git a/dts/Bindings/i2c/qcom,i2c-qup.txt b/dts/Bindings/i2c/qcom,i2c-qup.txt
new file mode 100644
index 0000000000..dc71754a56
--- /dev/null
+++ b/dts/Bindings/i2c/qcom,i2c-qup.txt
@@ -0,0 +1,40 @@
+Qualcomm Universal Peripheral (QUP) I2C controller
+
+Required properties:
+ - compatible: Should be:
+   * "qcom,i2c-qup-v1.1.1" for 8660, 8960 and 8064.
+   * "qcom,i2c-qup-v2.1.1" for 8974 v1.
+   * "qcom,i2c-qup-v2.2.1" for 8974 v2 and later.
+ - reg: Should contain QUP register address and length.
+ - interrupts: Should contain I2C interrupt.
+
+ - clocks: A list of phandles + clock-specifiers, one for each entry in
+   clock-names.
+ - clock-names: Should contain:
+   * "core" for the core clock
+   * "iface" for the AHB clock
+
+ - #address-cells: Should be <1> Address cells for i2c device address
+ - #size-cells: Should be <0> as i2c addresses have no size component
+
+Optional properties:
+ - clock-frequency: Should specify the desired i2c bus clock frequency in Hz,
+                    defaults to 100kHz if omitted.
+
+Child nodes should conform to i2c bus binding.
+
+Example:
+
+ i2c@f9924000 {
+ 	compatible = "qcom,i2c-qup-v2.2.1";
+ 	reg = <0xf9924000 0x1000>;
+ 	interrupts = <0 96 0>;
+
+ 	clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+ 	clock-names = "core", "iface";
+
+ 	clock-frequency = <355000>;
+
+ 	#address-cells = <1>;
+ 	#size-cells = <0>;
+ };
diff --git a/dts/Bindings/i2c/trivial-devices.txt b/dts/Bindings/i2c/trivial-devices.txt
new file mode 100644
index 0000000000..bef86e57c3
--- /dev/null
+++ b/dts/Bindings/i2c/trivial-devices.txt
@@ -0,0 +1,87 @@
+This is a list of trivial i2c devices that have simple device tree
+bindings, consisting only of a compatible field, an address and
+possibly an interrupt line.
+
+If a device needs more specific bindings, such as properties to
+describe some aspect of it, there needs to be a specific binding
+document for it just like any other devices.
+
+
+Compatible		Vendor / Chip
+==========		=============
+ad,ad7414		SMBus/I2C Digital Temperature Sensor in 6-Pin SOT with SMBus Alert and Over Temperature Pin
+ad,adm9240		ADM9240:  Complete System Hardware Monitor for uProcessor-Based Systems
+adi,adt7461		+/-1C TDM Extended Temp Range I.C
+adt7461			+/-1C TDM Extended Temp Range I.C
+adi,adt7473		+/-1C TDM Extended Temp Range I.C
+adi,adt7475		+/-1C TDM Extended Temp Range I.C
+adi,adt7476		+/-1C TDM Extended Temp Range I.C
+adi,adt7490		+/-1C TDM Extended Temp Range I.C
+at,24c08		i2c serial eeprom  (24cxx)
+atmel,24c00		i2c serial eeprom  (24cxx)
+atmel,24c01		i2c serial eeprom  (24cxx)
+atmel,24c02		i2c serial eeprom  (24cxx)
+atmel,24c04		i2c serial eeprom  (24cxx)
+atmel,24c16		i2c serial eeprom  (24cxx)
+atmel,24c32		i2c serial eeprom  (24cxx)
+atmel,24c64		i2c serial eeprom  (24cxx)
+atmel,24c128		i2c serial eeprom  (24cxx)
+atmel,24c256		i2c serial eeprom  (24cxx)
+atmel,24c512		i2c serial eeprom  (24cxx)
+atmel,24c1024		i2c serial eeprom  (24cxx)
+atmel,at97sc3204t	i2c trusted platform module (TPM)
+capella,cm32181		CM32181: Ambient Light Sensor
+catalyst,24c32		i2c serial eeprom
+cirrus,cs42l51		Cirrus Logic CS42L51 audio codec
+dallas,ds1307		64 x 8, Serial, I2C Real-Time Clock
+dallas,ds1338		I2C RTC with 56-Byte NV RAM
+dallas,ds1339		I2C Serial Real-Time Clock
+dallas,ds1340		I2C RTC with Trickle Charger
+dallas,ds1374		I2C, 32-Bit Binary Counter Watchdog RTC with Trickle Charger and Reset Input/Output
+dallas,ds1631		High-Precision Digital Thermometer
+dallas,ds1682		Total-Elapsed-Time Recorder with Alarm
+dallas,ds1775		Tiny Digital Thermometer and Thermostat
+dallas,ds3232		Extremely Accurate I²C RTC with Integrated Crystal and SRAM
+dallas,ds4510		CPU Supervisor with Nonvolatile Memory and Programmable I/O
+dallas,ds75		Digital Thermometer and Thermostat
+dialog,da9053		DA9053: flexible system level PMIC with multicore support
+epson,rx8025		High-Stability. I2C-Bus INTERFACE REAL TIME CLOCK MODULE
+epson,rx8581		I2C-BUS INTERFACE REAL TIME CLOCK MODULE
+fsl,mag3110		MAG3110: Xtrinsic High Accuracy, 3D Magnetometer
+fsl,mc13892		MC13892: Power Management Integrated Circuit (PMIC) for i.MX35/51
+fsl,mma8450		MMA8450Q: Xtrinsic Low-power, 3-axis Xtrinsic Accelerometer
+fsl,mpr121		MPR121: Proximity Capacitive Touch Sensor Controller
+fsl,sgtl5000		SGTL5000: Ultra Low-Power Audio Codec
+gmt,g751		G751: Digital Temperature Sensor and Thermal Watchdog with Two-Wire Interface
+infineon,slb9635tt	Infineon SLB9635 (Soft-) I2C TPM (old protocol, max 100khz)
+infineon,slb9645tt	Infineon SLB9645 I2C TPM (new protocol, max 400khz)
+isl,isl12057		Intersil ISL12057 I2C RTC Chip
+maxim,ds1050		5 Bit Programmable, Pulse-Width Modulator
+maxim,max1237		Low-Power, 4-/12-Channel, 2-Wire Serial, 12-Bit ADCs
+maxim,max6625		9-Bit/12-Bit Temperature Sensors with I²C-Compatible Serial Interface
+mc,rv3029c2		Real Time Clock Module with I2C-Bus
+national,lm63		Temperature sensor with integrated fan control
+national,lm75		I2C TEMP SENSOR
+national,lm80		Serial Interface ACPI-Compatible Microprocessor System Hardware Monitor
+national,lm85		Temperature sensor with integrated fan control
+national,lm92		±0.33°C Accurate, 12-Bit + Sign Temperature Sensor and Thermal Window Comparator with Two-Wire Interface
+nuvoton,npct501		i2c trusted platform module (TPM)
+nxp,pca9556		Octal SMBus and I2C registered interface
+nxp,pca9557		8-bit I2C-bus and SMBus I/O port with reset
+nxp,pcf8563		Real-time clock/calendar
+ovti,ov5642		OV5642: Color CMOS QSXGA (5-megapixel) Image Sensor with OmniBSI and Embedded TrueFocus
+pericom,pt7c4338	Real-time Clock Module
+plx,pex8648		48-Lane, 12-Port PCI Express Gen 2 (5.0 GT/s) Switch
+ramtron,24c64		i2c serial eeprom  (24cxx)
+ricoh,rs5c372a		I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
+samsung,24ad0xd1	S524AD0XF1 (128K/256K-bit Serial EEPROM for Low Power)
+sii,s35390a		2-wire CMOS real-time clock
+st-micro,24c256		i2c serial eeprom  (24cxx)
+stm,m41t00		Serial Access TIMEKEEPER
+stm,m41t62		Serial real-time clock (RTC) with alarm
+stm,m41t80		M41T80 - SERIAL ACCESS RTC WITH ALARMS
+taos,tsl2550		Ambient Light Sensor with SMBUS/Two Wire Serial Interface
+ti,tsc2003		I2C Touch-Screen Controller
+ti,tmp102		Low Power Digital Temperature Sensor with SMBUS/Two Wire Serial Interface
+ti,tmp275		Digital Temperature Sensor
+winbond,wpct301		i2c trusted platform module (TPM)