dts: update to v5.4-rc1

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

1 files changed, 0 insertions, 66 deletions

diff --git a/dts/Bindings/iio/adc/adi,ad7606.txt b/dts/Bindings/iio/adc/adi,ad7606.txt
deleted file mode 100644
index d865246019..0000000000
--- a/dts/Bindings/iio/adc/adi,ad7606.txt
+++ /dev/null
@@ -1,66 +0,0 @@
-Analog Devices AD7606 Simultaneous Sampling ADC
-
-Required properties for the AD7606:
-
-- compatible: Must be one of
-	* "adi,ad7605-4"
-	* "adi,ad7606-8"
-	* "adi,ad7606-6"
-	* "adi,ad7606-4"
-	* "adi,ad7616"
-- reg: SPI chip select number for the device
-- spi-max-frequency: Max SPI frequency to use
-	see: Documentation/devicetree/bindings/spi/spi-bus.txt
-- spi-cpha: See Documentation/devicetree/bindings/spi/spi-bus.txt
-- avcc-supply: phandle to the Avcc power supply
-- interrupts: IRQ line for the ADC
-	see: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
-- adi,conversion-start-gpios: must be the device tree identifier of the CONVST pin.
-		  This logic input is used to initiate conversions on the analog
-		  input channels. As the line is active high, it should be marked
-		  GPIO_ACTIVE_HIGH.
-
-Optional properties:
-
-- reset-gpios: must be the device tree identifier of the RESET pin. If specified,
-	       it will be asserted during driver probe. As the line is active high,
-	       it should be marked GPIO_ACTIVE_HIGH.
-- standby-gpios: must be the device tree identifier of the STBY pin. This pin is used
-		to place the AD7606 into one of two power-down modes, Standby mode or
-		Shutdown mode. As the line is active low, it should be marked
-		GPIO_ACTIVE_LOW.
-- adi,first-data-gpios: must be the device tree identifier of the FRSTDATA pin.
-		    The FRSTDATA output indicates when the first channel, V1, is
-		    being read back on either the parallel, byte or serial interface.
-		    As the line is active high, it should be marked GPIO_ACTIVE_HIGH.
-- adi,range-gpios: must be the device tree identifier of the RANGE pin. The polarity on
-	      this pin determines the input range of the analog input channels. If
-	      this pin is tied to a logic high, the analog input range is ±10V for
-	      all channels. If this pin is tied to a logic low, the analog input range
-	      is ±5V for all channels. As the line is active high, it should be marked
-	      GPIO_ACTIVE_HIGH.
-- adi,oversampling-ratio-gpios: must be the device tree identifier of the over-sampling
-				mode pins. As the line is active high, it should be marked
-				GPIO_ACTIVE_HIGH.
-
-Example:
-
-	adc@0 {
-		compatible = "adi,ad7606-8";
-		reg = <0>;
-		spi-max-frequency = <1000000>;
-		spi-cpol;
-
-		avcc-supply = <&adc_vref>;
-
-		interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
-		interrupt-parent = <&gpio>;
-
-		adi,conversion-start-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
-		reset-gpios = <&gpio 27 GPIO_ACTIVE_HIGH>;
-		adi,first-data-gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
-		adi,oversampling-ratio-gpios = <&gpio 18 GPIO_ACTIVE_HIGH
-						&gpio 23 GPIO_ACTIVE_HIGH
-						&gpio 26 GPIO_ACTIVE_HIGH>;
-		standby-gpios = <&gpio 24 GPIO_ACTIVE_LOW>;
-	};