dts: update to v5.2-rc1

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

1 files changed, 85 insertions, 0 deletions

diff --git a/dts/Bindings/iio/imu/adi,adis16480.txt b/dts/Bindings/iio/imu/adi,adis16480.txt
new file mode 100644
index 0000000000..ed7783f452
--- /dev/null
+++ b/dts/Bindings/iio/imu/adi,adis16480.txt
@@ -0,0 +1,85 @@
+
+Analog Devices ADIS16480 and similar IMUs
+
+Required properties for the ADIS16480:
+
+- compatible: Must be one of
+	* "adi,adis16375"
+	* "adi,adis16480"
+	* "adi,adis16485"
+	* "adi,adis16488"
+	* "adi,adis16495-1"
+	* "adi,adis16495-2"
+	* "adi,adis16495-3"
+	* "adi,adis16497-1"
+	* "adi,adis16497-2"
+	* "adi,adis16497-3"
+- reg: SPI chip select number for the device
+- spi-max-frequency: Max SPI frequency to use
+	see: Documentation/devicetree/bindings/spi/spi-bus.txt
+- spi-cpha: See Documentation/devicetree/bindings/spi/spi-bus.txt
+- spi-cpol: See Documentation/devicetree/bindings/spi/spi-bus.txt
+- interrupts: interrupt mapping for IRQ, accepted values are:
+	* IRQF_TRIGGER_RISING
+	* IRQF_TRIGGER_FALLING
+
+Optional properties:
+
+- interrupt-names: Data ready line selection. Valid values are:
+	* DIO1
+	* DIO2
+	* DIO3
+	* DIO4
+	If this field is left empty, DIO1 is assigned as default data ready
+	signal.
+- reset-gpios: must be the device tree identifier of the RESET pin. As the line
+	is active low, it should be marked GPIO_ACTIVE_LOW.
+- clocks: phandle to the external clock. Should be set according to
+	"clock-names".
+	If this field is left empty together with the "clock-names" field, then
+	the internal clock is used.
+- clock-names: The name of the external clock to be used. Valid values are:
+	* sync: In sync mode, the internal clock is disabled and the frequency
+		of the external clock signal establishes therate of data
+		collection and processing. See Fig 14 and 15 in the datasheet.
+		The clock-frequency must be:
+		* 3000 to 4500 Hz for adis1649x devices.
+		* 700 to 2400 Hz for adis1648x devices.
+	* pps: In Pulse Per Second (PPS) Mode, the rate of data collection and
+	       production is equal to the product of the external clock
+	       frequency and the scale factor in the SYNC_SCALE register, see
+	       Table 154 in the datasheet.
+	       The clock-frequency must be:
+	       * 1 to 128 Hz for adis1649x devices.
+	       * This mode is not supported by adis1648x devices.
+	If this field is left empty together with the "clocks" field, then the
+	internal clock is used.
+- adi,ext-clk-pin: The DIOx line to be used as an external clock input.
+	Valid values are:
+	* DIO1
+	* DIO2
+	* DIO3
+	* DIO4
+	Each DIOx pin supports only one function at a time (data ready line
+	selection or external clock input). When a single pin has two
+	two assignments, the enable bit for the lower priority function
+	automatically resets to zero (disabling the lower priority function).
+	Data ready has highest priority.
+	If this field is left empty, DIO2 is assigned as default external clock
+	input pin.
+
+Example:
+
+	imu@0 {
+		compatible = "adi,adis16495-1";
+		reg = <0>;
+		spi-max-frequency = <3200000>;
+		spi-cpol;
+		spi-cpha;
+		interrupts = <25 IRQF_TRIGGER_FALLING>;
+		interrupt-parent = <&gpio>;
+		interrupt-names = "DIO2";
+		clocks = <&adis16495_sync>;
+		clock-names = "sync";
+		adi,ext-clk-pin = "DIO1";
+	};