dts: update to v4.11-rc1

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

15 files changed, 533 insertions, 1 deletions

diff --git a/dts/Bindings/iio/accel/lis302.txt b/dts/Bindings/iio/accel/lis302.txt
index 2a19bff969..dfdce67826 100644
--- a/dts/Bindings/iio/accel/lis302.txt
+++ b/dts/Bindings/iio/accel/lis302.txt
@@ -5,7 +5,7 @@ that apply in on the generic device (independent from the bus).
 
 
 Required properties for the SPI bindings:
- - compatible: 		should be set to "st,lis3lv02d_spi"
+ - compatible: 		should be set to "st,lis3lv02d-spi"
  - reg:			the chipselect index
  - spi-max-frequency:	maximal bus speed, should be set to 1000000 unless
 			constrained by external circuitry
diff --git a/dts/Bindings/iio/adc/amlogic,meson-saradc.txt b/dts/Bindings/iio/adc/amlogic,meson-saradc.txt
new file mode 100644
index 0000000000..f9e3ff2c65
--- /dev/null
+++ b/dts/Bindings/iio/adc/amlogic,meson-saradc.txt
@@ -0,0 +1,32 @@
+* Amlogic Meson SAR (Successive Approximation Register) A/D converter
+
+Required properties:
+- compatible:	depending on the SoC this should be one of:
+			- "amlogic,meson-gxbb-saradc" for GXBB
+			- "amlogic,meson-gxl-saradc" for GXL
+			- "amlogic,meson-gxm-saradc" for GXM
+		along with the generic "amlogic,meson-saradc"
+- reg:		the physical base address and length of the registers
+- clocks:	phandle and clock identifier (see clock-names)
+- clock-names:	mandatory clocks:
+			- "clkin" for the reference clock (typically XTAL)
+			- "core" for the SAR ADC core clock
+		optional clocks:
+			- "sana" for the analog clock
+			- "adc_clk" for the ADC (sampling) clock
+			- "adc_sel" for the ADC (sampling) clock mux
+- vref-supply:	the regulator supply for the ADC reference voltage
+- #io-channel-cells: must be 1, see ../iio-bindings.txt
+
+Example:
+	saradc: adc@8680 {
+		compatible = "amlogic,meson-gxl-saradc", "amlogic,meson-saradc";
+		#io-channel-cells = <1>;
+		reg = <0x0 0x8680 0x0 0x34>;
+		clocks = <&xtal>,
+			 <&clkc CLKID_SAR_ADC>,
+			 <&clkc CLKID_SANA>,
+			 <&clkc CLKID_SAR_ADC_CLK>,
+			 <&clkc CLKID_SAR_ADC_SEL>;
+		clock-names = "clkin", "core", "sana", "adc_clk", "adc_sel";
+	};
diff --git a/dts/Bindings/iio/adc/avia-hx711.txt b/dts/Bindings/iio/adc/avia-hx711.txt
new file mode 100644
index 0000000000..b3629405f5
--- /dev/null
+++ b/dts/Bindings/iio/adc/avia-hx711.txt
@@ -0,0 +1,18 @@
+* AVIA HX711 ADC chip for weight cells
+  Bit-banging driver
+
+Required properties:
+ - compatible:	Should be "avia,hx711"
+ - sck-gpios:	Definition of the GPIO for the clock
+ - dout-gpios:	Definition of the GPIO for data-out
+		See Documentation/devicetree/bindings/gpio/gpio.txt
+ - avdd-supply:	Definition of the regulator used as analog supply
+
+Example:
+weight@0 {
+	compatible = "avia,hx711";
+	sck-gpios = <&gpio3 10 GPIO_ACTIVE_HIGH>;
+	dout-gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
+	avdd-suppy = <&avdd>;
+};
+
diff --git a/dts/Bindings/iio/adc/max11100.txt b/dts/Bindings/iio/adc/max11100.txt
new file mode 100644
index 0000000000..b7f7177b8a
--- /dev/null
+++ b/dts/Bindings/iio/adc/max11100.txt
@@ -0,0 +1,18 @@
+* Maxim max11100 Analog to Digital Converter (ADC)
+
+Required properties:
+  - compatible: Should be "maxim,max11100"
+  - reg: the adc unit address
+  - vref-supply: phandle to the regulator that provides reference voltage
+
+Optional properties:
+  - spi-max-frequency: SPI maximum frequency
+
+Example:
+
+max11100: adc@0 {
+        compatible = "maxim,max11100";
+        reg = <0>;
+        vref-supply = <&adc0_vref>;
+        spi-max-frequency = <240000>;
+};
diff --git a/dts/Bindings/iio/adc/qcom,pm8xxx-xoadc.txt b/dts/Bindings/iio/adc/qcom,pm8xxx-xoadc.txt
new file mode 100644
index 0000000000..53cd146d80
--- /dev/null
+++ b/dts/Bindings/iio/adc/qcom,pm8xxx-xoadc.txt
@@ -0,0 +1,149 @@
+Qualcomm's PM8xxx voltage XOADC
+
+The Qualcomm PM8xxx PMICs contain a HK/XO ADC (Housekeeping/Crystal
+oscillator ADC) encompassing PM8018, PM8038, PM8058 and PM8921.
+
+Required properties:
+
+- compatible: should be one of:
+  "qcom,pm8018-adc"
+  "qcom,pm8038-adc"
+  "qcom,pm8058-adc"
+  "qcom,pm8921-adc"
+
+- reg: should contain the ADC base address in the PMIC, typically
+  0x197.
+
+- xoadc-ref-supply: should reference a regulator that can supply
+  a reference voltage on demand. The reference voltage may vary
+  with PMIC variant but is typically something like 2.2 or 1.8V.
+
+The following required properties are standard for IO channels, see
+iio-bindings.txt for more details:
+
+- #address-cells: should be set to <1>
+
+- #size-cells: should be set to <0>
+
+- #io-channel-cells: should be set to <1>
+
+- interrupts: should refer to the parent PMIC interrupt controller
+  and reference the proper ADC interrupt.
+
+Required subnodes:
+
+The ADC channels are configured as subnodes of the ADC. Since some of
+them are used for calibrating the ADC, these nodes are compulsory:
+
+adc-channel@c {
+	reg = <0x0c>;
+};
+
+adc-channel@d {
+	reg = <0x0d>;
+};
+
+adc-channel@f {
+	reg = <0x0f>;
+};
+
+These three nodes are used for absolute and ratiometric calibration
+and only need to have these reg values: they are by hardware definition
+1:1 ratio converters that sample 625, 1250 and 0 milliV and create
+an interpolation calibration for all other ADCs.
+
+Optional subnodes: any channels other than channel 0x0c, 0x0d and
+0x0f are optional.
+
+Required channel node properties:
+
+- reg: should contain the hardware channel number in the range
+  0 .. 0x0f (4 bits). The hardware only supports 16 channels.
+
+Optional channel node properties:
+
+- qcom,decimation:
+  Value type: <u32>
+  Definition: This parameter is used to decrease the ADC sampling rate.
+          Quicker measurements can be made by reducing the decimation ratio.
+          Valid values are 512, 1024, 2048, 4096.
+          If the property is not found, a default value of 512 will be used.
+
+- qcom,ratiometric:
+  Value type: <u32>
+  Definition: Channel calibration type. If this property is specified
+          VADC will use a special voltage references for channel
+          calibration. The available references are specified in the
+	  as a u32 value setting (see below) and it is compulsory
+	  to also specify this reference if ratiometric calibration
+	  is selected.
+
+	  If the property is not found, the channel will be
+          calibrated with the 0.625V and 1.25V reference channels, also
+          known as an absolute calibration.
+  The reference voltage pairs when using ratiometric calibration:
+	  0 = XO_IN/XOADC_GND
+	  1 = PMIC_IN/XOADC_GND
+	  2 = PMIC_IN/BMS_CSP
+	  3 (invalid)
+	  4 = XOADC_GND/XOADC_GND
+	  5 = XOADC_VREF/XOADC_GND
+
+Example:
+
+xoadc: xoadc@197 {
+	compatible = "qcom,pm8058-adc";
+	reg = <0x197>;
+	interrupt-parent = <&pm8058>;
+	interrupts = <76 1>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	#io-channel-cells = <1>;
+
+	vcoin: adc-channel@0 {
+		reg = <0x00>;
+	};
+	vbat: adc-channel@1 {
+		reg = <0x01>;
+	};
+	dcin: adc-channel@2 {
+		reg = <0x02>;
+	};
+	ichg: adc-channel@3 {
+		reg = <0x03>;
+	};
+	vph_pwr: adc-channel@4 {
+		reg = <0x04>;
+	};
+	usb_vbus: adc-channel@a {
+		reg = <0x0a>;
+	};
+	die_temp: adc-channel@b {
+		reg = <0x0b>;
+	};
+	ref_625mv: adc-channel@c {
+		reg = <0x0c>;
+	};
+	ref_1250mv: adc-channel@d {
+		reg = <0x0d>;
+	};
+	ref_325mv: adc-channel@e {
+		reg = <0x0e>;
+	};
+	ref_muxoff: adc-channel@f {
+		reg = <0x0f>;
+	};
+};
+
+
+/* IIO client node */
+iio-hwmon {
+	compatible = "iio-hwmon";
+	io-channels = <&xoadc 0x01>, /* Battery */
+		    <&xoadc 0x02>, /* DC in (charger) */
+		    <&xoadc 0x04>, /* VPH the main system voltage */
+		    <&xoadc 0x0b>, /* Die temperature */
+		    <&xoadc 0x0c>, /* Reference voltage 1.25V */
+		    <&xoadc 0x0d>, /* Reference voltage 0.625V */
+		    <&xoadc 0x0e>; /* Reference voltage 0.325V */
+};
diff --git a/dts/Bindings/iio/adc/renesas,gyroadc.txt b/dts/Bindings/iio/adc/renesas,gyroadc.txt
new file mode 100644
index 0000000000..f5b0adae60
--- /dev/null
+++ b/dts/Bindings/iio/adc/renesas,gyroadc.txt
@@ -0,0 +1,99 @@
+* Renesas RCar GyroADC device driver
+
+The GyroADC block is a reduced SPI block with up to 8 chipselect lines,
+which supports the SPI protocol of a selected few SPI ADCs. The SPI ADCs
+are sampled by the GyroADC block in a round-robin fashion and the result
+presented in the GyroADC registers.
+
+Required properties:
+- compatible:	Should be "<soc-specific>", "renesas,rcar-gyroadc".
+                The <soc-specific> should be one of:
+		renesas,r8a7791-gyroadc - for the GyroADC block present
+					  in r8a7791 SoC
+		renesas,r8a7792-gyroadc - for the GyroADC with interrupt
+					  block present in r8a7792 SoC
+- reg:		Address and length of the register set for the device
+- clocks:	References to all the clocks specified in the clock-names
+		property as specified in
+		Documentation/devicetree/bindings/clock/clock-bindings.txt.
+- clock-names:	Shall contain "fck" and "if". The "fck" is the GyroADC block
+		clock, the "if" is the interface clock.
+- power-domains: Must contain a reference to the PM domain, if available.
+- #address-cells: Should be <1> (setting for the subnodes) for all ADCs
+		except for "fujitsu,mb88101a". Should be <0> (setting for
+		only subnode) for "fujitsu,mb88101a".
+- #size-cells:	Should be <0> (setting for the subnodes)
+
+Sub-nodes:
+You must define subnode(s) which select the connected ADC type and reference
+voltage for the GyroADC channels.
+
+Required properties for subnodes:
+- compatible:	Should be either of:
+		"fujitsu,mb88101a"
+			- Fujitsu MB88101A compatible mode,
+			  12bit sampling, up to 4 channels can be sampled in
+			  round-robin fashion. One Fujitsu chip supplies four
+			  GyroADC channels with data as it contains four ADCs
+			  on the chip and thus for 4-channel operation, single
+			  MB88101A is required. The Cx chipselect lines of the
+			  MB88101A connect directly to two CHS lines of the
+			  GyroADC, no demuxer is required. The data out line
+			  of each MB88101A connects to a shared input pin of
+			  the GyroADC.
+		"ti,adcs7476" or "ti,adc121" or "adi,ad7476"
+			- TI ADCS7476 / TI ADC121 / ADI AD7476 compatible mode,
+			  15bit sampling, up to 8 channels can be sampled in
+			  round-robin fashion. One TI/ADI chip supplies single
+			  ADC channel with data, thus for 8-channel operation,
+			  8 chips are required. A 3:8 chipselect demuxer is
+			  required to connect the nCS line of the TI/ADI chips
+			  to the GyroADC, while MISO line of each TI/ADI ADC
+			  connects to a shared input pin of the GyroADC.
+		"maxim,max1162" or "maxim,max11100"
+			- Maxim MAX1162 / Maxim MAX11100 compatible mode,
+			  16bit sampling, up to 8 channels can be sampled in
+			  round-robin fashion. One Maxim chip supplies single
+			  ADC channel with data, thus for 8-channel operation,
+			  8 chips are required. A 3:8 chipselect demuxer is
+			  required to connect the nCS line of the MAX chips
+			  to the GyroADC, while MISO line of each Maxim ADC
+			  connects to a shared input pin of the GyroADC.
+- reg:		Should be the number of the analog input. Should be present
+		for all ADCs except "fujitsu,mb88101a".
+- vref-supply:	Reference to the channel reference voltage regulator.
+
+Example:
+	vref_max1162: regulator-vref-max1162 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "MAX1162 Vref";
+		regulator-min-microvolt = <4096000>;
+		regulator-max-microvolt = <4096000>;
+	};
+
+	adc@e6e54000 {
+		compatible = "renesas,r8a7791-gyroadc", "renesas,rcar-gyroadc";
+		reg = <0 0xe6e54000 0 64>;
+		clocks = <&mstp9_clks R8A7791_CLK_GYROADC>, <&clk_65m>;
+		clock-names = "fck", "if";
+		power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
+
+		pinctrl-0 = <&adc_pins>;
+		pinctrl-names = "default";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		adc@0 {
+			reg = <0>;
+			compatible = "maxim,max1162";
+			vref-supply = <&vref_max1162>;
+		};
+
+		adc@1 {
+			reg = <1>;
+			compatible = "maxim,max1162";
+			vref-supply = <&vref_max1162>;
+		};
+	};
diff --git a/dts/Bindings/iio/adc/st,stm32-adc.txt b/dts/Bindings/iio/adc/st,stm32-adc.txt
index 49ed82e898..5dfc88ec24 100644
--- a/dts/Bindings/iio/adc/st,stm32-adc.txt
+++ b/dts/Bindings/iio/adc/st,stm32-adc.txt
@@ -53,6 +53,11 @@ Required properties:
 - #io-channel-cells = <1>: See the IIO bindings section "IIO consumers" in
   Documentation/devicetree/bindings/iio/iio-bindings.txt
 
+Optional properties:
+- dmas: Phandle to dma channel for this ADC instance.
+  See ../../dma/dma.txt for details.
+- dma-names: Must be "rx" when dmas property is being used.
+
 Example:
 	adc: adc@40012000 {
 		compatible = "st,stm32f4-adc-core";
@@ -77,6 +82,8 @@ Example:
 			interrupt-parent = <&adc>;
 			interrupts = <0>;
 			st,adc-channels = <8>;
+			dmas = <&dma2 0 0 0x400 0x0>;
+			dma-names = "rx";
 		};
 		...
 		other adc child nodes follow...
diff --git a/dts/Bindings/iio/adc/ti-ads7950.txt b/dts/Bindings/iio/adc/ti-ads7950.txt
new file mode 100644
index 0000000000..e77a6f7e10
--- /dev/null
+++ b/dts/Bindings/iio/adc/ti-ads7950.txt
@@ -0,0 +1,23 @@
+* Texas Instruments ADS7950 family of A/DC chips
+
+Required properties:
+ - compatible: Must be one of "ti,ads7950", "ti,ads7951", "ti,ads7952",
+   "ti,ads7953", "ti,ads7954", "ti,ads7955", "ti,ads7956", "ti,ads7957",
+   "ti,ads7958", "ti,ads7959", "ti,ads7960", or "ti,ads7961"
+ - reg: SPI chip select number for the device
+ - #io-channel-cells: Must be 1 as per ../iio-bindings.txt
+ - vref-supply: phandle to a regulator node that supplies the 2.5V or 5V
+   reference voltage
+
+Recommended properties:
+ - spi-max-frequency: Definition as per
+		Documentation/devicetree/bindings/spi/spi-bus.txt
+
+Example:
+adc@0 {
+	compatible = "ti,ads7957";
+	reg = <0>;
+	#io-channel-cells = <1>;
+	vref-supply = <&refin_supply>;
+	spi-max-frequency = <10000000>;
+};
diff --git a/dts/Bindings/iio/imu/bmi160.txt b/dts/Bindings/iio/imu/bmi160.txt
new file mode 100644
index 0000000000..ae0112c7de
--- /dev/null
+++ b/dts/Bindings/iio/imu/bmi160.txt
@@ -0,0 +1,36 @@
+Bosch BMI160 - Inertial Measurement Unit with Accelerometer, Gyroscope
+and externally connectable Magnetometer
+
+https://www.bosch-sensortec.com/bst/products/all_products/bmi160
+
+Required properties:
+ - compatible : should be "bosch,bmi160"
+ - reg : the I2C address or SPI chip select number of the sensor
+ - spi-max-frequency : set maximum clock frequency (only for SPI)
+
+Optional properties:
+ - interrupt-parent : should be the phandle of the interrupt controller
+ - interrupts : interrupt mapping for IRQ, must be IRQ_TYPE_LEVEL_LOW
+ - interrupt-names : set to "INT1" if INT1 pin should be used as interrupt
+   input, set to "INT2" if INT2 pin should be used instead
+
+Examples:
+
+bmi160@68 {
+	compatible = "bosch,bmi160";
+	reg = <0x68>;
+
+	interrupt-parent = <&gpio4>;
+	interrupts = <12 IRQ_TYPE_LEVEL_LOW>;
+	interrupt-names = "INT1";
+};
+
+bmi160@0 {
+	compatible = "bosch,bmi160";
+	reg = <0>;
+	spi-max-frequency = <10000000>;
+
+	interrupt-parent = <&gpio2>;
+	interrupts = <12 IRQ_TYPE_LEVEL_LOW>;
+	interrupt-names = "INT2";
+};
diff --git a/dts/Bindings/iio/imu/st_lsm6dsx.txt b/dts/Bindings/iio/imu/st_lsm6dsx.txt
new file mode 100644
index 0000000000..cf81afdf78
--- /dev/null
+++ b/dts/Bindings/iio/imu/st_lsm6dsx.txt
@@ -0,0 +1,26 @@
+* ST_LSM6DSx driver for STM 6-axis (acc + gyro) imu Mems sensors
+
+Required properties:
+- compatible: must be one of:
+  "st,lsm6ds3"
+  "st,lsm6dsm"
+- reg: i2c address of the sensor / spi cs line
+
+Optional properties:
+- st,drdy-int-pin: the pin on the package that will be used to signal
+  "data ready" (valid values: 1 or 2).
+- interrupt-parent: should be the phandle for the interrupt controller
+- interrupts: interrupt mapping for IRQ. It should be configured with
+  flags IRQ_TYPE_LEVEL_HIGH or IRQ_TYPE_EDGE_RISING.
+
+  Refer to interrupt-controller/interrupts.txt for generic interrupt
+  client node bindings.
+
+Example:
+
+lsm6dsm@6b {
+	compatible = "st,lsm6dsm";
+	reg = <0x6b>;
+	interrupt-parent = <&gpio0>;
+	interrupts = <0 IRQ_TYPE_EDGE_RISING>;
+};
diff --git a/dts/Bindings/iio/light/cm3605.txt b/dts/Bindings/iio/light/cm3605.txt
new file mode 100644
index 0000000000..56331a79f9
--- /dev/null
+++ b/dts/Bindings/iio/light/cm3605.txt
@@ -0,0 +1,41 @@
+Capella Microsystems CM3605
+Ambient Light and Short Distance Proximity Sensor
+
+The CM3605 is an entirely analog part which however require quite a bit of
+software logic to interface a host operating system.
+
+This ALS and proximity sensor was one of the very first deployed in mobile
+handsets, notably it is used in the very first Nexus One Android phone from
+2010.
+
+Required properties:
+- compatible: must be: "capella,cm3605"
+- aset-gpios: GPIO line controlling the ASET line (drive low
+  to activate the ALS, should be flagged GPIO_ACTIVE_LOW)
+- interrupts: the IRQ line (such as a GPIO) that is connected to
+  the POUT (proximity sensor out) line. The edge detection must
+  be set to IRQ_TYPE_EDGE_BOTH so as to detect movements toward
+  and away from the proximity sensor.
+- io-channels: the ADC channel used for converting the voltage from
+  AOUT to a digital representation.
+- io-channel-names: must be "aout"
+
+Optional properties:
+- vdd-supply: regulator supplying VDD power to the component.
+- capella,aset-resistance-ohms: the sensitivity calibration resistance,
+  in Ohms. Valid values are: 50000, 100000, 300000 and 600000,
+  as these are the resistance values that we are supplied with
+  calibration curves for. If not supplied, 100 kOhm will be assumed
+  but it is strongly recommended to supply this.
+
+Example:
+
+cm3605 {
+	compatible = "capella,cm3605";
+	vdd-supply = <&foo_reg>;
+	aset-gpios = <&foo_gpio 1 GPIO_ACTIVE_LOW>;
+	capella,aset-resistance-ohms = <100000>;
+	interrupts = <1 IRQ_TYPE_EDGE_BOTH>;
+	io-channels = <&adc 0x01>;
+	io-channel-names = "aout";
+};
diff --git a/dts/Bindings/iio/potentiometer/max5481.txt b/dts/Bindings/iio/potentiometer/max5481.txt
new file mode 100644
index 0000000000..6a91b106e0
--- /dev/null
+++ b/dts/Bindings/iio/potentiometer/max5481.txt
@@ -0,0 +1,23 @@
+* Maxim Linear-Taper Digital Potentiometer MAX5481-MAX5484
+
+The node for this driver must be a child node of a SPI controller, hence
+all mandatory properties described in
+
+        Documentation/devicetree/bindings/spi/spi-bus.txt
+
+must be specified.
+
+Required properties:
+	- compatible:  	Must be one of the following, depending on the
+			model:
+			"maxim,max5481"
+			"maxim,max5482"
+			"maxim,max5483"
+			"maxim,max5484"
+
+Example:
+max548x: max548x@0 {
+	compatible = "maxim,max5482";
+	spi-max-frequency = <7000000>;
+	reg = <0>; /* chip-select */
+};
diff --git a/dts/Bindings/iio/st-sensors.txt b/dts/Bindings/iio/st-sensors.txt
index c040c9ad18..eaa8fbba34 100644
--- a/dts/Bindings/iio/st-sensors.txt
+++ b/dts/Bindings/iio/st-sensors.txt
@@ -27,6 +27,8 @@ standard bindings from pinctrl/pinctrl-bindings.txt.
 Valid compatible strings:
 
 Accelerometers:
+- st,lis3lv02d (deprecated, use st,lis3lv02dl-accel)
+- st,lis302dl-spi (deprecated, use st,lis3lv02dl-accel)
 - st,lis3lv02dl-accel
 - st,lsm303dlh-accel
 - st,lsm303dlhc-accel
diff --git a/dts/Bindings/iio/temperature/tmp007.txt b/dts/Bindings/iio/temperature/tmp007.txt
new file mode 100644
index 0000000000..b63aba91ef
--- /dev/null
+++ b/dts/Bindings/iio/temperature/tmp007.txt
@@ -0,0 +1,35 @@
+* TI TMP007 - IR thermopile sensor with integrated math engine
+
+Link to datasheet: http://www.ti.com/lit/ds/symlink/tmp007.pdf
+
+Required properties:
+
+  - compatible: should be "ti,tmp007"
+  - reg: the I2C address of the sensor (changeable via ADR pins)
+		------------------------------
+		|ADR1 | ADR0 | Device Address|
+		------------------------------
+		   0      0        0x40
+		   0	  1	   0x41
+		   0	 SDA       0x42
+		   0     SCL       0x43
+		   1      0        0x44
+		   1      1        0x45
+		   1	 SDA	   0x46
+		   1     SCL       0x47
+
+Optional properties:
+
+  - interrupt-parent: should be the phandle for the interrupt controller
+
+  - interrupts: interrupt mapping for GPIO IRQ (level active low)
+
+Example:
+
+tmp007@40 {
+        compatible = "ti,tmp007";
+        reg = <0x40>;
+	interrupt-parent = <&gpio0>;
+	interrupts = <5 0x08>;
+};
+
diff --git a/dts/Bindings/iio/timer/stm32-timer-trigger.txt b/dts/Bindings/iio/timer/stm32-timer-trigger.txt
new file mode 100644
index 0000000000..55a653d153
--- /dev/null
+++ b/dts/Bindings/iio/timer/stm32-timer-trigger.txt
@@ -0,0 +1,23 @@
+STMicroelectronics STM32 Timers IIO timer bindings
+
+Must be a sub-node of an STM32 Timers device tree node.
+See ../mfd/stm32-timers.txt for details about the parent node.
+
+Required parameters:
+- compatible:	Must be "st,stm32-timer-trigger".
+- reg:		Identify trigger hardware block.
+
+Example:
+	timers@40010000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "st,stm32-timers";
+		reg = <0x40010000 0x400>;
+		clocks = <&rcc 0 160>;
+		clock-names = "clk_int";
+
+		timer@0 {
+			compatible = "st,stm32-timer-trigger";
+			reg = <0>;
+		};
+	};