Add devicetree source files as of Linux-3.15-rc2

This adds the Linux dts files to barebox. The dts files are
generated from Ian Campbells device-tree-rebasing.git:

git://xenbits.xen.org/people/ianc/device-tree-rebasing.git

The dts are found in dts/ in the barebox repository and
will be updated from upstream regularly, probably for each upstream
-rc.

To keep the synchronization with upstream easy no changes to
the original files are allowed under dts/. Instead changes to
upstream dts files will be done using overlays in arch/$ARCH/dts/.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

38 files changed, 1416 insertions, 0 deletions

diff --git a/dts/Bindings/input/ads7846.txt b/dts/Bindings/input/ads7846.txt
new file mode 100644
index 0000000000..5f7619c227
--- /dev/null
+++ b/dts/Bindings/input/ads7846.txt
@@ -0,0 +1,91 @@
+Device tree bindings for TI's ADS7843, ADS7845, ADS7846, ADS7873, TSC2046
+SPI driven touch screen controllers.
+
+The node for this driver must be a child node of a SPI controller, hence
+all mandatory properties described in
+
+	Documentation/devicetree/bindings/spi/spi-bus.txt
+
+must be specified.
+
+Additional required properties:
+
+	compatible		Must be one of the following, depending on the
+				model:
+					"ti,tsc2046"
+					"ti,ads7843"
+					"ti,ads7845"
+					"ti,ads7846"
+					"ti,ads7873"
+
+	interrupt-parent
+	interrupts		An interrupt node describing the IRQ line the chip's
+				!PENIRQ pin is connected to.
+	vcc-supply		A regulator node for the supply voltage.
+
+
+Optional properties:
+
+	ti,vref-delay-usecs		vref supply delay in usecs, 0 for
+					external vref (u16).
+	ti,vref-mv			The VREF voltage, in millivolts (u16).
+	ti,keep-vref-on			set to keep vref on for differential
+					measurements as well
+	ti,swap-xy			swap x and y axis
+	ti,settle-delay-usec		Settling time of the analog signals;
+					a function of Vcc and the capacitance
+					on the X/Y drivers.  If set to non-zero,
+					two samples are taken with settle_delay
+					us apart, and the second one is used.
+					~150 uSec with 0.01uF caps (u16).
+	ti,penirq-recheck-delay-usecs	If set to non-zero, after samples are
+					taken this delay is applied and penirq
+					is rechecked, to help avoid false
+					events.  This value is affected by the
+					material used to build the touch layer
+					(u16).
+	ti,x-plate-ohms			Resistance of the X-plate,
+					in Ohms (u16).
+	ti,y-plate-ohms			Resistance of the Y-plate,
+					in Ohms (u16).
+	ti,x-min			Minimum value on the X axis (u16).
+	ti,y-min			Minimum value on the Y axis (u16).
+	ti,x-max			Maximum value on the X axis (u16).
+	ti,y-max			Minimum value on the Y axis (u16).
+	ti,pressure-min			Minimum reported pressure value
+					(threshold) - u16.
+	ti,pressure-max			Maximum reported pressure value (u16).
+	ti,debounce-max			Max number of additional readings per
+					sample (u16).
+	ti,debounce-tol			Tolerance used for filtering (u16).
+	ti,debounce-rep			Additional consecutive good readings
+					required after the first two (u16).
+	ti,pendown-gpio-debounce	Platform specific debounce time for the
+					pendown-gpio (u32).
+	pendown-gpio			GPIO handle describing the pin the !PENIRQ
+					line is connected to.
+	linux,wakeup			use any event on touchscreen as wakeup event.
+
+
+Example for a TSC2046 chip connected to an McSPI controller of an OMAP SoC::
+
+	spi_controller {
+		tsc2046@0 {
+			reg = <0>;	/* CS0 */
+			compatible = "ti,tsc2046";
+			interrupt-parent = <&gpio1>;
+			interrupts = <8 0>;	/* BOOT6 / GPIO 8 */
+			spi-max-frequency = <1000000>;
+			pendown-gpio = <&gpio1 8 0>;
+			vcc-supply = <&reg_vcc3>;
+
+			ti,x-min = /bits/ 16 <0>;
+			ti,x-max = /bits/ 16 <8000>;
+			ti,y-min = /bits/ 16 <0>;
+			ti,y-max = /bits/ 16 <4800>;
+			ti,x-plate-ohms = /bits/ 16 <40>;
+			ti,pressure-max = /bits/ 16 <255>;
+
+			linux,wakeup;
+		};
+	};
diff --git a/dts/Bindings/input/clps711x-keypad.txt b/dts/Bindings/input/clps711x-keypad.txt
new file mode 100644
index 0000000000..e68d2bbc6c
--- /dev/null
+++ b/dts/Bindings/input/clps711x-keypad.txt
@@ -0,0 +1,27 @@
+* Cirrus Logic CLPS711X matrix keypad device tree bindings
+
+Required Properties:
+- compatible:    Shall contain "cirrus,clps711x-keypad".
+- row-gpios:     List of GPIOs used as row lines.
+- poll-interval: Poll interval time in milliseconds.
+- linux,keymap:  The definition can be found at
+                 bindings/input/matrix-keymap.txt.
+
+Optional Properties:
+- autorepeat:    Enable autorepeat feature.
+
+Example:
+	keypad {
+		compatible = "cirrus,ep7312-keypad", "cirrus,clps711x-keypad";
+		autorepeat;
+		poll-interval = <120>;
+		row-gpios = <&porta 0 0>,
+			    <&porta 1 0>;
+
+		linux,keymap = <
+			MATRIX_KEY(0, 0, KEY_UP)
+			MATRIX_KEY(0, 1, KEY_DOWN)
+			MATRIX_KEY(1, 0, KEY_LEFT)
+			MATRIX_KEY(1, 1, KEY_RIGHT)
+		>;
+	};
diff --git a/dts/Bindings/input/cros-ec-keyb.txt b/dts/Bindings/input/cros-ec-keyb.txt
new file mode 100644
index 0000000000..0f6355ce39
--- /dev/null
+++ b/dts/Bindings/input/cros-ec-keyb.txt
@@ -0,0 +1,72 @@
+ChromeOS EC Keyboard
+
+Google's ChromeOS EC Keyboard is a simple matrix keyboard implemented on
+a separate EC (Embedded Controller) device. It provides a message for reading
+key scans from the EC. These are then converted into keycodes for processing
+by the kernel.
+
+This binding is based on matrix-keymap.txt and extends/modifies it as follows:
+
+Required properties:
+- compatible: "google,cros-ec-keyb"
+
+Optional properties:
+- google,needs-ghost-filter: True to enable a ghost filter for the matrix
+keyboard. This is recommended if the EC does not have its own logic or
+hardware for this.
+
+
+Example:
+
+cros-ec-keyb {
+	compatible = "google,cros-ec-keyb";
+	keypad,num-rows = <8>;
+	keypad,num-columns = <13>;
+	google,needs-ghost-filter;
+	/*
+	 * Keymap entries take the form of 0xRRCCKKKK where
+	 * RR=Row CC=Column KKKK=Key Code
+	 * The values below are for a US keyboard layout and
+	 * are taken from the Linux driver. Note that the
+	 * 102ND key is not used for US keyboards.
+	 */
+	linux,keymap = <
+		/* CAPSLCK F1         B          F10     */
+		0x0001003a 0x0002003b 0x00030030 0x00040044
+		/* N       =          R_ALT      ESC     */
+		0x00060031 0x0008000d 0x000a0064 0x01010001
+		/* F4      G          F7         H       */
+		0x0102003e 0x01030022 0x01040041 0x01060023
+		/* '       F9         BKSPACE    L_CTRL  */
+		0x01080028 0x01090043 0x010b000e 0x0200001d
+		/* TAB     F3         T          F6      */
+		0x0201000f 0x0202003d 0x02030014 0x02040040
+		/* ]       Y          102ND      [       */
+		0x0205001b 0x02060015 0x02070056 0x0208001a
+		/* F8      GRAVE      F2         5       */
+		0x02090042 0x03010029 0x0302003c 0x03030006
+		/* F5      6          -          \       */
+		0x0304003f 0x03060007 0x0308000c 0x030b002b
+		/* R_CTRL  A          D          F       */
+		0x04000061 0x0401001e 0x04020020 0x04030021
+		/* S       K          J          ;       */
+		0x0404001f 0x04050025 0x04060024 0x04080027
+		/* L       ENTER      Z          C       */
+		0x04090026 0x040b001c 0x0501002c 0x0502002e
+		/* V       X          ,          M       */
+		0x0503002f 0x0504002d 0x05050033 0x05060032
+		/* L_SHIFT /          .          SPACE   */
+		0x0507002a 0x05080035 0x05090034 0x050B0039
+		/* 1       3          4          2       */
+		0x06010002 0x06020004 0x06030005 0x06040003
+		/* 8       7          0          9       */
+		0x06050009 0x06060008 0x0608000b 0x0609000a
+		/* L_ALT   DOWN       RIGHT      Q       */
+		0x060a0038 0x060b006c 0x060c006a 0x07010010
+		/* E       R          W          I       */
+		0x07020012 0x07030013 0x07040011 0x07050017
+		/* U       R_SHIFT    P          O       */
+		0x07060016 0x07070036 0x07080019 0x07090018
+		/* UP      LEFT    */
+		0x070b0067 0x070c0069>;
+};
diff --git a/dts/Bindings/input/fsl-mma8450.txt b/dts/Bindings/input/fsl-mma8450.txt
new file mode 100644
index 0000000000..0b96e5737d
--- /dev/null
+++ b/dts/Bindings/input/fsl-mma8450.txt
@@ -0,0 +1,12 @@
+* Freescale MMA8450 3-Axis Accelerometer
+
+Required properties:
+- compatible : "fsl,mma8450".
+- reg: the I2C address of MMA8450
+
+Example:
+
+accelerometer: mma8450@1c {
+	compatible = "fsl,mma8450";
+	reg = <0x1c>;
+};
diff --git a/dts/Bindings/input/gpio-beeper.txt b/dts/Bindings/input/gpio-beeper.txt
new file mode 100644
index 0000000000..a5086e37fc
--- /dev/null
+++ b/dts/Bindings/input/gpio-beeper.txt
@@ -0,0 +1,13 @@
+* GPIO beeper device tree bindings
+
+Register a beeper connected to GPIO pin.
+
+Required properties:
+- compatible:	Should be "gpio-beeper".
+- gpios:	From common gpio binding; gpio connection to beeper enable pin.
+
+Example:
+	beeper: beeper {
+		compatible = "gpio-beeper";
+		gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>;
+	};
diff --git a/dts/Bindings/input/gpio-keys-polled.txt b/dts/Bindings/input/gpio-keys-polled.txt
new file mode 100644
index 0000000000..313abefa37
--- /dev/null
+++ b/dts/Bindings/input/gpio-keys-polled.txt
@@ -0,0 +1,38 @@
+Device-Tree bindings for input/gpio_keys_polled.c keyboard driver
+
+Required properties:
+	- compatible = "gpio-keys-polled";
+	- poll-interval: Poll interval time in milliseconds
+
+Optional properties:
+	- autorepeat: Boolean, Enable auto repeat feature of Linux input
+	  subsystem.
+
+Each button (key) is represented as a sub-node of "gpio-keys-polled":
+Subnode properties:
+
+	- gpios: OF device-tree gpio specification.
+	- label: Descriptive name of the key.
+	- linux,code: Keycode to emit.
+
+Optional subnode-properties:
+	- linux,input-type: Specify event type this button/key generates.
+	  If not specified defaults to <1> == EV_KEY.
+	- debounce-interval: Debouncing interval time in milliseconds.
+	  If not specified defaults to 5.
+	- gpio-key,wakeup: Boolean, button can wake-up the system.
+
+Example nodes:
+
+	gpio_keys_polled {
+			compatible = "gpio-keys-polled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			poll-interval = <100>;
+			autorepeat;
+			button@21 {
+				label = "GPIO Key UP";
+				linux,code = <103>;
+				gpios = <&gpio1 0 1>;
+			};
+			...
diff --git a/dts/Bindings/input/gpio-matrix-keypad.txt b/dts/Bindings/input/gpio-matrix-keypad.txt
new file mode 100644
index 0000000000..ead641c65e
--- /dev/null
+++ b/dts/Bindings/input/gpio-matrix-keypad.txt
@@ -0,0 +1,46 @@
+* GPIO driven matrix keypad device tree bindings
+
+GPIO driven matrix keypad is used to interface a SoC with a matrix keypad.
+The matrix keypad supports multiple row and column lines, a key can be
+placed at each intersection of a unique row and a unique column. The matrix
+keypad can sense a key-press and key-release by means of GPIO lines and
+report the event using GPIO interrupts to the cpu.
+
+Required Properties:
+- compatible:		Should be "gpio-matrix-keypad"
+- row-gpios:		List of gpios used as row lines. The gpio specifier
+			for this property depends on the gpio controller to
+			which these row lines are connected.
+- col-gpios:		List of gpios used as column lines. The gpio specifier
+			for this property depends on the gpio controller to
+			which these column lines are connected.
+- linux,keymap:		The definition can be found at
+			bindings/input/matrix-keymap.txt
+
+Optional Properties:
+- linux,no-autorepeat:	do no enable autorepeat feature.
+- linux,wakeup:		use any event on keypad as wakeup event.
+- debounce-delay-ms:	debounce interval in milliseconds
+- col-scan-delay-us:	delay, measured in microseconds, that is needed
+			before we can scan keypad after activating column gpio
+
+Example:
+	matrix-keypad {
+		compatible = "gpio-matrix-keypad";
+		debounce-delay-ms = <5>;
+		col-scan-delay-us = <2>;
+
+		row-gpios = <&gpio2 25 0
+			     &gpio2 26 0
+			     &gpio2 27 0>;
+
+		col-gpios = <&gpio2 21 0
+			     &gpio2 22 0>;
+
+		linux,keymap = <0x0000008B
+				0x0100009E
+				0x02000069
+				0x0001006A
+				0x0101001C
+				0x0201006C>;
+	};
diff --git a/dts/Bindings/input/imx-keypad.txt b/dts/Bindings/input/imx-keypad.txt
new file mode 100644
index 0000000000..2ebaf7d268
--- /dev/null
+++ b/dts/Bindings/input/imx-keypad.txt
@@ -0,0 +1,53 @@
+* Freescale i.MX Keypad Port(KPP) device tree bindings
+
+The KPP is designed to interface with a keypad matrix with 2-point contact
+or 3-point contact keys. The KPP is designed to simplify the software task
+of scanning a keypad matrix. The KPP is capable of detecting, debouncing,
+and decoding one or multiple keys pressed simultaneously on a keypad.
+
+Required SoC Specific Properties:
+- compatible: Should be "fsl,<soc>-kpp".
+
+- reg: Physical base address of the KPP and length of memory mapped
+  region.
+
+- interrupts: The KPP interrupt number to the CPU(s).
+
+- clocks: The clock provided by the SoC to the KPP. Some SoCs use dummy
+clock(The clock for the KPP is provided by the SoCs automatically).
+
+Required Board Specific Properties:
+- pinctrl-names: The definition can be found at
+pinctrl/pinctrl-bindings.txt.
+
+- pinctrl-0: The definition can be found at
+pinctrl/pinctrl-bindings.txt.
+
+- linux,keymap: The definition can be found at
+bindings/input/matrix-keymap.txt.
+
+Example:
+kpp: kpp@73f94000 {
+	compatible = "fsl,imx51-kpp", "fsl,imx21-kpp";
+	reg = <0x73f94000 0x4000>;
+	interrupts = <60>;
+	clocks = <&clks 0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_kpp_1>;
+	linux,keymap = <0x00000067	/* KEY_UP */
+			0x0001006c	/* KEY_DOWN */
+			0x00020072	/* KEY_VOLUMEDOWN */
+			0x00030066	/* KEY_HOME */
+			0x0100006a	/* KEY_RIGHT */
+			0x01010069	/* KEY_LEFT */
+			0x0102001c	/* KEY_ENTER */
+			0x01030073	/* KEY_VOLUMEUP */
+			0x02000040	/* KEY_F6 */
+			0x02010042	/* KEY_F8 */
+			0x02020043	/* KEY_F9 */
+			0x02030044	/* KEY_F10 */
+			0x0300003b	/* KEY_F1 */
+			0x0301003c	/* KEY_F2 */
+			0x0302003d	/* KEY_F3 */
+			0x03030074>;	/* KEY_POWER */
+};
diff --git a/dts/Bindings/input/input-reset.txt b/dts/Bindings/input/input-reset.txt
new file mode 100644
index 0000000000..2bb2626fdb
--- /dev/null
+++ b/dts/Bindings/input/input-reset.txt
@@ -0,0 +1,33 @@
+Input: sysrq reset sequence
+
+A simple binding to represent a set of keys as described in
+include/uapi/linux/input.h. This is to communicate a sequence of keys to the
+sysrq driver. Upon holding the keys for a specified amount of time (if
+specified) the system is sync'ed and reset.
+
+Key sequences are global to the system but all the keys in a set must be coming
+from the same input device.
+
+The /chosen node should contain a 'linux,sysrq-reset-seq' child node to define
+a set of keys.
+
+Required property:
+sysrq-reset-seq: array of Linux keycodes, one keycode per cell.
+
+Optional property:
+timeout-ms: duration keys must be pressed together in milliseconds before
+generating a sysrq. If omitted the system is rebooted immediately when a valid
+sequence has been recognized.
+
+Example:
+
+ chosen {
+                linux,sysrq-reset-seq {
+                        keyset = <0x03
+                                  0x04
+                                  0x0a>;
+                        timeout-ms = <3000>;
+                };
+         };
+
+Would represent KEY_2, KEY_3 and KEY_9.
diff --git a/dts/Bindings/input/lpc32xx-key.txt b/dts/Bindings/input/lpc32xx-key.txt
new file mode 100644
index 0000000000..bcf62f8563
--- /dev/null
+++ b/dts/Bindings/input/lpc32xx-key.txt
@@ -0,0 +1,31 @@
+NXP LPC32xx Key Scan Interface
+
+This binding is based on the matrix-keymap binding with the following
+changes:
+
+Required Properties:
+- compatible: Should be "nxp,lpc3220-key"
+- reg: Physical base address of the controller and length of memory mapped
+  region.
+- interrupts: The interrupt number to the cpu.
+- nxp,debounce-delay-ms: Debounce delay in ms
+- nxp,scan-delay-ms: Repeated scan period in ms
+- linux,keymap: the key-code to be reported when the key is pressed
+  and released, see also
+  Documentation/devicetree/bindings/input/matrix-keymap.txt
+
+Note: keypad,num-rows and keypad,num-columns are required, and must be equal
+since LPC32xx only supports square matrices
+
+Example:
+
+	key@40050000 {
+		compatible = "nxp,lpc3220-key";
+		reg = <0x40050000 0x1000>;
+		interrupts = <54 0>;
+		keypad,num-rows = <1>;
+		keypad,num-columns = <1>;
+		nxp,debounce-delay-ms = <3>;
+		nxp,scan-delay-ms = <34>;
+		linux,keymap = <0x00000002>;
+	};
diff --git a/dts/Bindings/input/matrix-keymap.txt b/dts/Bindings/input/matrix-keymap.txt
new file mode 100644
index 0000000000..c54919fad1
--- /dev/null
+++ b/dts/Bindings/input/matrix-keymap.txt
@@ -0,0 +1,27 @@
+A simple common binding for matrix-connected key boards. Currently targeted at
+defining the keys in the scope of linux key codes since that is a stable and
+standardized interface at this time.
+
+Required properties:
+- linux,keymap: an array of packed 1-cell entries containing the equivalent
+  of row, column and linux key-code. The 32-bit big endian cell is packed
+  as:
+	row << 24 | column << 16 | key-code
+
+Optional properties:
+Properties for the number of rows and columns are optional because some
+drivers will use fixed values for these.
+- keypad,num-rows: Number of row lines connected to the keypad controller.
+- keypad,num-columns: Number of column lines connected to the keypad
+  controller.
+
+Some users of this binding might choose to specify secondary keymaps for
+cases where there is a modifier key such as a Fn key. Proposed names
+for said properties are "linux,fn-keymap" or with another descriptive
+word for the modifier other from "Fn".
+
+Example:
+	linux,keymap = < 0x00030012
+			 0x0102003a >;
+	keypad,num-rows = <2>;
+	keypad,num-columns = <8>;
diff --git a/dts/Bindings/input/nvidia,tegra20-kbc.txt b/dts/Bindings/input/nvidia,tegra20-kbc.txt
new file mode 100644
index 0000000000..0382b8bd69
--- /dev/null
+++ b/dts/Bindings/input/nvidia,tegra20-kbc.txt
@@ -0,0 +1,54 @@
+* Tegra keyboard controller
+The key controller has maximum 24 pins to make matrix keypad. Any pin
+can be configured as row or column. The maximum column pin can be 8
+and maximum row pins can be 16 for Tegra20/Tegra30.
+
+Required properties:
+- compatible: "nvidia,tegra20-kbc"
+- reg: Register base address of KBC.
+- interrupts: Interrupt number for the KBC.
+- nvidia,kbc-row-pins: The KBC pins which are configured as row. This is an
+  array of pin numbers which is used as rows.
+- nvidia,kbc-col-pins: The KBC pins which are configured as column. This is an
+  array of pin numbers which is used as column.
+- linux,keymap: The keymap for keys as described in the binding document
+  devicetree/bindings/input/matrix-keymap.txt.
+- clocks: Must contain one entry, for the module clock.
+  See ../clocks/clock-bindings.txt for details.
+- resets: Must contain an entry for each entry in reset-names.
+  See ../reset/reset.txt for details.
+- reset-names: Must include the following entries:
+  - kbc
+
+Optional properties, in addition to those specified by the shared
+matrix-keyboard bindings:
+
+- linux,fn-keymap: a second keymap, same specification as the
+  matrix-keyboard-controller spec but to be used when the KEY_FN modifier
+  key is pressed.
+- nvidia,debounce-delay-ms: delay in milliseconds per row scan for debouncing
+- nvidia,repeat-delay-ms: delay in milliseconds before repeat starts
+- nvidia,ghost-filter: enable ghost filtering for this device
+- nvidia,wakeup-source: configure keyboard as a wakeup source for suspend/resume
+
+Example:
+
+keyboard: keyboard {
+	compatible = "nvidia,tegra20-kbc";
+	reg = <0x7000e200 0x100>;
+	interrupts = <0 85 0x04>;
+	clocks = <&tegra_car 36>;
+	resets = <&tegra_car 36>;
+	reset-names = "kbc";
+	nvidia,ghost-filter;
+	nvidia,debounce-delay-ms = <640>;
+	nvidia,kbc-row-pins = <0 1 2>;    /* pin 0, 1, 2 as rows */
+	nvidia,kbc-col-pins = <11 12 13>; /* pin 11, 12, 13 as columns */
+	linux,keymap = <0x00000074
+			0x00010067
+			0x00020066
+			0x01010068
+			0x02000069
+			0x02010070
+			0x02020071>;
+};
diff --git a/dts/Bindings/input/omap-keypad.txt b/dts/Bindings/input/omap-keypad.txt
new file mode 100644
index 0000000000..34ed1c60ff
--- /dev/null
+++ b/dts/Bindings/input/omap-keypad.txt
@@ -0,0 +1,28 @@
+* TI's Keypad Controller device tree bindings
+
+TI's Keypad controller is used to interface a SoC with a matrix-type
+keypad device. The keypad controller supports multiple row and column lines.
+A key can be placed at each intersection of a unique row and a unique column.
+The keypad controller can sense a key-press and key-release and report the
+event using a interrupt to the cpu.
+
+This binding is based on the matrix-keymap binding with the following
+changes:
+
+keypad,num-rows and keypad,num-columns are required.
+
+Required SoC Specific Properties:
+- compatible: should be one of the following
+   - "ti,omap4-keypad": For controllers compatible with omap4 keypad
+      controller.
+
+Optional Properties specific to linux:
+- linux,keypad-no-autorepeat: do no enable autorepeat feature.
+
+Example:
+	keypad@4ae1c000{
+		compatible = "ti,omap4-keypad";
+		keypad,num-rows = <2>;
+		keypad,num-columns = <8>;
+		linux,keypad-no-autorepeat;
+	};
diff --git a/dts/Bindings/input/ps2keyb-mouse-apbps2.txt b/dts/Bindings/input/ps2keyb-mouse-apbps2.txt
new file mode 100644
index 0000000000..3029c5694c
--- /dev/null
+++ b/dts/Bindings/input/ps2keyb-mouse-apbps2.txt
@@ -0,0 +1,16 @@
+Aeroflex Gaisler APBPS2 PS/2 Core, supporting Keyboard or Mouse.
+
+The APBPS2 PS/2 core is available in the GRLIB VHDL IP core library.
+
+Note: In the ordinary environment for the APBPS2 core, a LEON SPARC system,
+these properties are built from information in the AMBA plug&play and from
+bootloader settings.
+
+Required properties:
+
+- name : Should be "GAISLER_APBPS2" or "01_060"
+- reg : Address and length of the register set for the device
+- interrupts : Interrupt numbers for this device
+
+For further information look in the documentation for the GLIB IP core library:
+http://www.gaisler.com/products/grlib/grip.pdf
diff --git a/dts/Bindings/input/pwm-beeper.txt b/dts/Bindings/input/pwm-beeper.txt
new file mode 100644
index 0000000000..be332ae4f2
--- /dev/null
+++ b/dts/Bindings/input/pwm-beeper.txt
@@ -0,0 +1,7 @@
+* PWM beeper device tree bindings
+
+Registers a PWM device as beeper.
+
+Required properties:
+- compatible: should be "pwm-beeper"
+- pwms: phandle to the physical PWM device
diff --git a/dts/Bindings/input/pxa27x-keypad.txt b/dts/Bindings/input/pxa27x-keypad.txt
new file mode 100644
index 0000000000..f8674f7e5e
--- /dev/null
+++ b/dts/Bindings/input/pxa27x-keypad.txt
@@ -0,0 +1,60 @@
+* Marvell PXA Keypad controller
+
+Required Properties
+- compatible : should be "marvell,pxa27x-keypad"
+- reg : Address and length of the register set for the device
+- interrupts : The interrupt for the keypad controller
+- marvell,debounce-interval : How long time the key will be
+  recognized when it is pressed. It is a u32 value, and bit[31:16]
+  is debounce interval for direct key and bit[15:0] is debounce
+  interval for matrix key. The value is in binary number of 2ms
+
+Optional Properties For Matrix Keyes
+Please refer to matrix-keymap.txt
+
+Optional Properties for Direct Keyes
+- marvell,direct-key-count : How many direct keyes are used.
+- marvell,direct-key-mask : The mask indicates which keyes
+  are used. If bit[X] of the mask is set, the direct key X
+  is used.
+- marvell,direct-key-low-active : Direct key status register
+  tells the level of pins that connects to the direct keyes.
+  When this property is set, it means that when the pin level
+  is low, the key is pressed(active).
+- marvell,direct-key-map : It is a u16 array. Each item indicates
+  the linux key-code for the direct key.
+
+Optional Properties For Rotary
+- marvell,rotary0 : It is a u32 value. Bit[31:16] is the
+  linux key-code for rotary up. Bit[15:0] is the linux key-code
+  for rotary down. It is for rotary 0.
+- marvell,rotary1 : Same as marvell,rotary0. It is for rotary 1.
+- marvell,rotary-rel-key : When rotary is used for relative axes
+  in the device, the value indicates the key-code for relative
+  axes measurement in the device. It is a u32 value. Bit[31:16]
+  is for rotary 1, and Bit[15:0] is for rotary 0.
+
+Examples:
+	keypad: keypad@d4012000 {
+		keypad,num-rows = <3>;
+		keypad,num-columns = <5>;
+		linux,keymap = <0x0000000e	/* KEY_BACKSPACE */
+				0x0001006b	/* KEY_END */
+				0x00020061	/* KEY_RIGHTCTRL */
+				0x0003000b	/* KEY_0 */
+				0x00040002	/* KEY_1 */
+				0x0100008b	/* KEY_MENU */
+				0x01010066	/* KEY_HOME */
+				0x010200e7	/* KEY_SEND */
+				0x01030009	/* KEY_8 */
+				0x0104000a	/* KEY_9 */
+				0x02000160	/* KEY_OK */
+				0x02010003	/* KEY_2 */
+				0x02020004	/* KEY_3 */
+				0x02030005	/* KEY_4 */
+				0x02040006>;	/* KEY_5 */
+		marvell,rotary0 = <0x006c0067>;	/* KEY_UP & KEY_DOWN */
+		marvell,direct-key-count = <1>;
+		marvell,direct-key-map = <0x001c>;
+		marvell,debounce-interval = <0x001e001e>;
+	};
diff --git a/dts/Bindings/input/qcom,pm8xxx-keypad.txt b/dts/Bindings/input/qcom,pm8xxx-keypad.txt
new file mode 100644
index 0000000000..7d8cb92831
--- /dev/null
+++ b/dts/Bindings/input/qcom,pm8xxx-keypad.txt
@@ -0,0 +1,89 @@
+Qualcomm PM8xxx PMIC Keypad
+
+PROPERTIES
+
+- compatible:
+	Usage: required
+	Value type: <string>
+	Definition: must be one of:
+		    "qcom,pm8058-keypad"
+		    "qcom,pm8921-keypad"
+
+- reg:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: address of keypad control register
+
+- interrupts:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: the first interrupt specifies the key sense interrupt
+		    and the second interrupt specifies the key stuck interrupt.
+		    The format of the specifier is defined by the binding
+		    document describing the node's interrupt parent.
+
+- linux,keymap:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: the linux keymap. More information can be found in
+		    input/matrix-keymap.txt.
+
+- linux,keypad-no-autorepeat:
+	Usage: optional
+	Value type: <bool>
+	Definition: don't enable autorepeat feature.
+
+- linux,keypad-wakeup:
+	Usage: optional
+	Value type: <bool>
+	Definition: use any event on keypad as wakeup event.
+
+- keypad,num-rows:
+	Usage: required
+	Value type: <u32>
+	Definition: number of rows in the keymap. More information can be found
+		    in input/matrix-keymap.txt.
+
+- keypad,num-columns:
+	Usage: required
+	Value type: <u32>
+	Definition: number of columns in the keymap. More information can be
+		    found in input/matrix-keymap.txt.
+
+- debounce:
+	Usage: optional
+	Value type: <u32>
+	Definition: time in microseconds that key must be pressed or release
+		    for key sense interrupt to trigger.
+
+- scan-delay:
+	Usage: optional
+	Value type: <u32>
+	Definition: time in microseconds to pause between successive scans
+		    of the matrix array.
+
+- row-hold:
+	Usage: optional
+	Value type: <u32>
+	Definition: time in nanoseconds to pause between scans of each row in
+		    the matrix array.
+
+EXAMPLE
+
+	keypad@148 {
+		compatible = "qcom,pm8921-keypad";
+		reg = <0x148>;
+		interrupt-parent = <&pmicintc>;
+		interrupts = <74 1>, <75 1>;
+		linux,keymap = <
+			MATRIX_KEY(0, 0, KEY_VOLUMEUP)
+			MATRIX_KEY(0, 1, KEY_VOLUMEDOWN)
+			MATRIX_KEY(0, 2, KEY_CAMERA_FOCUS)
+			MATRIX_KEY(0, 3, KEY_CAMERA)
+			>;
+		keypad,num-rows = <1>;
+		keypad,num-columns = <5>;
+		debounce = <15>;
+		scan-delay = <32>;
+		row-hold = <91500>;
+	};
diff --git a/dts/Bindings/input/qcom,pm8xxx-pwrkey.txt b/dts/Bindings/input/qcom,pm8xxx-pwrkey.txt
new file mode 100644
index 0000000000..588536cc96
--- /dev/null
+++ b/dts/Bindings/input/qcom,pm8xxx-pwrkey.txt
@@ -0,0 +1,46 @@
+Qualcomm PM8xxx PMIC Power Key
+
+PROPERTIES
+
+- compatible:
+	Usage: required
+	Value type: <string>
+	Definition: must be one of:
+		    "qcom,pm8058-pwrkey"
+		    "qcom,pm8921-pwrkey"
+
+- reg:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: address of power key control register
+
+- interrupts:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: the first interrupt specifies the key release interrupt
+		    and the second interrupt specifies the key press interrupt.
+		    The format of the specifier is defined by the binding
+		    document describing the node's interrupt parent.
+
+- debounce:
+	Usage: optional
+	Value type: <u32>
+	Definition: time in microseconds that key must be pressed or release
+		    for state change interrupt to trigger.
+
+- pull-up:
+	Usage: optional
+	Value type: <empty>
+	Definition: presence of this property indicates that the KPDPWR_N pin
+		    should be configured for pull up.
+
+EXAMPLE
+
+	pwrkey@1c {
+		compatible = "qcom,pm8921-pwrkey";
+		reg = <0x1c>;
+		interrupt-parent = <&pmicintc>;
+		interrupts = <50 1>, <51 1>;
+		debounce = <15625>;
+		pull-up;
+	};
diff --git a/dts/Bindings/input/qcom,pm8xxx-vib.txt b/dts/Bindings/input/qcom,pm8xxx-vib.txt
new file mode 100644
index 0000000000..4ed467b1e4
--- /dev/null
+++ b/dts/Bindings/input/qcom,pm8xxx-vib.txt
@@ -0,0 +1,22 @@
+Qualcomm PM8xxx PMIC Vibrator
+
+PROPERTIES
+
+- compatible:
+	Usage: required
+	Value type: <string>
+	Definition: must be one of:
+		    "qcom,pm8058-vib"
+		    "qcom,pm8921-vib"
+
+- reg:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: address of vibration control register
+
+EXAMPLE
+
+	vibrator@4a {
+		compatible = "qcom,pm8058-vib";
+		reg = <0x4a>;
+	};
diff --git a/dts/Bindings/input/rotary-encoder.txt b/dts/Bindings/input/rotary-encoder.txt
new file mode 100644
index 0000000000..331549593e
--- /dev/null
+++ b/dts/Bindings/input/rotary-encoder.txt
@@ -0,0 +1,36 @@
+Rotary encoder DT bindings
+
+Required properties:
+- gpios: a spec for two GPIOs to be used
+
+Optional properties:
+- linux,axis: the input subsystem axis to map to this rotary encoder.
+  Defaults to 0 (ABS_X / REL_X)
+- rotary-encoder,steps: Number of steps in a full turnaround of the
+  encoder. Only relevant for absolute axis. Defaults to 24 which is a
+  typical value for such devices.
+- rotary-encoder,relative-axis: register a relative axis rather than an
+  absolute one. Relative axis will only generate +1/-1 events on the input
+  device, hence no steps need to be passed.
+- rotary-encoder,rollover: Automatic rollove when the rotary value becomes
+  greater than the specified steps or smaller than 0. For absolute axis only.
+- rotary-encoder,half-period: Makes the driver work on half-period mode.
+
+See Documentation/input/rotary-encoder.txt for more information.
+
+Example:
+
+		rotary@0 {
+			compatible = "rotary-encoder";
+			gpios = <&gpio 19 1>, <&gpio 20 0>; /* GPIO19 is inverted */
+			linux,axis = <0>; /* REL_X */
+			rotary-encoder,relative-axis;
+		};
+
+		rotary@1 {
+			compatible = "rotary-encoder";
+			gpios = <&gpio 21 0>, <&gpio 22 0>;
+			linux,axis = <1>; /* ABS_Y */
+			rotary-encoder,steps = <24>;
+			rotary-encoder,rollover;
+		};
diff --git a/dts/Bindings/input/samsung-keypad.txt b/dts/Bindings/input/samsung-keypad.txt
new file mode 100644
index 0000000000..942d071baa
--- /dev/null
+++ b/dts/Bindings/input/samsung-keypad.txt
@@ -0,0 +1,74 @@
+* Samsung's Keypad Controller device tree bindings
+
+Samsung's Keypad controller is used to interface a SoC with a matrix-type
+keypad device. The keypad controller supports multiple row and column lines.
+A key can be placed at each intersection of a unique row and a unique column.
+The keypad controller can sense a key-press and key-release and report the
+event using a interrupt to the cpu.
+
+Required SoC Specific Properties:
+- compatible: should be one of the following
+  - "samsung,s3c6410-keypad": For controllers compatible with s3c6410 keypad
+    controller.
+  - "samsung,s5pv210-keypad": For controllers compatible with s5pv210 keypad
+    controller.
+
+- reg: physical base address of the controller and length of memory mapped
+  region.
+
+- interrupts: The interrupt number to the cpu.
+
+Required Board Specific Properties:
+- samsung,keypad-num-rows: Number of row lines connected to the keypad
+  controller.
+
+- samsung,keypad-num-columns: Number of column lines connected to the
+  keypad controller.
+
+- Keys represented as child nodes: Each key connected to the keypad
+  controller is represented as a child node to the keypad controller
+  device node and should include the following properties.
+  - keypad,row: the row number to which the key is connected.
+  - keypad,column: the column number to which the key is connected.
+  - linux,code: the key-code to be reported when the key is pressed
+    and released.
+
+- pinctrl-0: Should specify pin control groups used for this controller.
+- pinctrl-names: Should contain only one value - "default".
+
+Optional Properties specific to linux:
+- linux,keypad-no-autorepeat: do no enable autorepeat feature.
+- linux,keypad-wakeup: use any event on keypad as wakeup event.
+
+
+Example:
+	keypad@100A0000 {
+		compatible = "samsung,s5pv210-keypad";
+		reg = <0x100A0000 0x100>;
+		interrupts = <173>;
+		samsung,keypad-num-rows = <2>;
+		samsung,keypad-num-columns = <8>;
+		linux,input-no-autorepeat;
+		linux,input-wakeup;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&keypad_rows &keypad_columns>;
+
+		key_1 {
+			keypad,row = <0>;
+			keypad,column = <3>;
+			linux,code = <2>;
+		};
+
+		key_2 {
+			keypad,row = <0>;
+			keypad,column = <4>;
+			linux,code = <3>;
+		};
+
+		key_3 {
+			keypad,row = <0>;
+			keypad,column = <5>;
+			linux,code = <4>;
+		};
+	};
diff --git a/dts/Bindings/input/spear-keyboard.txt b/dts/Bindings/input/spear-keyboard.txt
new file mode 100644
index 0000000000..4a846d26da
--- /dev/null
+++ b/dts/Bindings/input/spear-keyboard.txt
@@ -0,0 +1,20 @@
+* SPEAr keyboard controller
+
+Required properties:
+- compatible: "st,spear300-kbd"
+
+Optional properties, in addition to those specified by the shared
+matrix-keyboard bindings:
+- autorepeat: bool: enables key autorepeat
+- st,mode: keyboard mode: 0 - 9x9, 1 - 6x6, 2 - 2x2
+
+Example:
+
+kbd@fc400000 {
+	compatible = "st,spear300-kbd";
+	reg = <0xfc400000 0x100>;
+	linux,keymap = < 0x00030012
+			 0x0102003a >;
+	autorepeat;
+	st,mode = <0>;
+};
diff --git a/dts/Bindings/input/stmpe-keypad.txt b/dts/Bindings/input/stmpe-keypad.txt
new file mode 100644
index 0000000000..1b97222e8a
--- /dev/null
+++ b/dts/Bindings/input/stmpe-keypad.txt
@@ -0,0 +1,39 @@
+* STMPE Keypad
+
+Required properties:
+ - compatible               : "st,stmpe-keypad"
+ - linux,keymap             : See ./matrix-keymap.txt
+
+Optional properties:
+ - debounce-interval        : Debouncing interval time in milliseconds
+ - st,scan-count            : Scanning cycles elapsed before key data is updated
+ - st,no-autorepeat         : If specified device will not autorepeat
+
+Example:
+
+	stmpe_keypad {
+		compatible = "st,stmpe-keypad";
+
+		debounce-interval = <64>;
+		st,scan-count = <8>;
+		st,no-autorepeat;
+
+		linux,keymap = <0x205006b
+				0x4010074
+				0x3050072
+				0x1030004
+				0x502006a
+				0x500000a
+				0x5008b
+				0x706001c
+				0x405000b
+				0x6070003
+				0x3040067
+				0x303006c
+				0x60400e7
+				0x602009e
+				0x4020073
+				0x5050002
+				0x4030069
+				0x3020008>;
+	};
diff --git a/dts/Bindings/input/tca8418_keypad.txt b/dts/Bindings/input/tca8418_keypad.txt
new file mode 100644
index 0000000000..2551850091
--- /dev/null
+++ b/dts/Bindings/input/tca8418_keypad.txt
@@ -0,0 +1,10 @@
+This binding is based on the matrix-keymap binding with the following
+changes:
+
+keypad,num-rows and keypad,num-columns are required.
+
+Required properties:
+- compatible: "ti,tca8418"
+- reg: the I2C address
+- interrupts: IRQ line number, should trigger on falling edge
+- linux,keymap: Keys definitions, see keypad-matrix.
diff --git a/dts/Bindings/input/ti,nspire-keypad.txt b/dts/Bindings/input/ti,nspire-keypad.txt
new file mode 100644
index 0000000000..513d94d6e8
--- /dev/null
+++ b/dts/Bindings/input/ti,nspire-keypad.txt
@@ -0,0 +1,60 @@
+TI-NSPIRE Keypad
+
+Required properties:
+- compatible: Compatible property value should be "ti,nspire-keypad".
+
+- reg: Physical base address of the peripheral and length of memory mapped
+  region.
+
+- interrupts: The interrupt number for the peripheral.
+
+- scan-interval: How often to scan in us. Based on a APB speed of 33MHz, the
+	maximum and minimum delay time is ~2000us and ~500us respectively
+
+- row-delay: How long to wait before scanning each row.
+
+- clocks: The clock this peripheral is attached to.
+
+- linux,keymap: The keymap to use
+	(see Documentation/devicetree/bindings/input/matrix-keymap.txt)
+
+Optional properties:
+- active-low: Specify that the keypad is active low (i.e. logical low signifies
+	a key press).
+
+Example:
+
+input {
+	compatible = "ti,nspire-keypad";
+	reg = <0x900E0000 0x1000>;
+	interrupts = <16>;
+
+	scan-interval = <1000>;
+	row-delay = <200>;
+
+	clocks = <&apb_pclk>;
+
+	linux,keymap = <
+	0x0000001c	0x0001001c	0x00040039
+	0x0005002c	0x00060015	0x0007000b
+	0x0008000f	0x0100002d	0x01010011
+	0x0102002f	0x01030004	0x01040016
+	0x01050014	0x0106001f	0x01070002
+	0x010a006a	0x02000013	0x02010010
+	0x02020019	0x02030007	0x02040018
+	0x02050031	0x02060032	0x02070005
+	0x02080028	0x0209006c	0x03000026
+	0x03010025	0x03020024	0x0303000a
+	0x03040017	0x03050023	0x03060022
+	0x03070008	0x03080035	0x03090069
+	0x04000021	0x04010012	0x04020020
+	0x0404002e	0x04050030	0x0406001e
+	0x0407000d	0x04080037	0x04090067
+	0x05010038	0x0502000c	0x0503001b
+	0x05040034	0x0505001a	0x05060006
+	0x05080027	0x0509000e	0x050a006f
+	0x0600002b	0x0602004e	0x06030068
+	0x06040003	0x0605006d	0x06060009
+	0x06070001	0x0609000f	0x0708002a
+	0x0709001d	0x070a0033	>;
+};
diff --git a/dts/Bindings/input/touchscreen/auo_pixcir_ts.txt b/dts/Bindings/input/touchscreen/auo_pixcir_ts.txt
new file mode 100644
index 0000000000..f40f21c642
--- /dev/null
+++ b/dts/Bindings/input/touchscreen/auo_pixcir_ts.txt
@@ -0,0 +1,30 @@
+* AUO in-cell touchscreen controller using Pixcir sensors
+
+Required properties:
+- compatible: must be "auo,auo_pixcir_ts"
+- reg: I2C address of the chip
+- interrupts: interrupt to which the chip is connected
+- gpios: gpios the chip is connected to
+  first one is the interrupt gpio and second one the reset gpio
+- x-size: horizontal resolution of touchscreen
+- y-size: vertical resolution of touchscreen
+
+Example:
+
+	i2c@00000000 {
+		/* ... */
+
+		auo_pixcir_ts@5c {
+			compatible = "auo,auo_pixcir_ts";
+			reg = <0x5c>;
+			interrupts = <2 0>;
+
+			gpios = <&gpf 2 0 2>, /* INT */
+				<&gpf 5 1 0>; /* RST */
+
+			x-size = <800>;
+			y-size = <600>;
+		};
+
+		/* ... */
+	};
diff --git a/dts/Bindings/input/touchscreen/bu21013.txt b/dts/Bindings/input/touchscreen/bu21013.txt
new file mode 100644
index 0000000000..ca5a2c8648
--- /dev/null
+++ b/dts/Bindings/input/touchscreen/bu21013.txt
@@ -0,0 +1,28 @@
+* Rohm BU21013 Touch Screen
+
+Required properties:
+ - compatible              : "rohm,bu21013_tp"
+ - reg                     :  I2C device address
+
+Optional properties:
+ - touch-gpio              : GPIO pin registering a touch event
+ - <supply_name>-supply    : Phandle to a regulator supply
+ - rohm,touch-max-x        : Maximum outward permitted limit in the X axis
+ - rohm,touch-max-y        : Maximum outward permitted limit in the Y axis
+ - rohm,flip-x             : Flip touch coordinates on the X axis
+ - rohm,flip-y             : Flip touch coordinates on the Y axis
+
+Example:
+
+	i2c@80110000 {
+		bu21013_tp@0x5c {
+			compatible = "rohm,bu21013_tp";
+			reg = <0x5c>;
+			touch-gpio = <&gpio2 20 0x4>;
+			avdd-supply = <&ab8500_ldo_aux1_reg>;
+
+			rohm,touch-max-x = <384>;
+			rohm,touch-max-y = <704>;
+			rohm,flip-y;
+		};
+	};
diff --git a/dts/Bindings/input/touchscreen/edt-ft5x06.txt b/dts/Bindings/input/touchscreen/edt-ft5x06.txt
new file mode 100644
index 0000000000..76db96704a
--- /dev/null
+++ b/dts/Bindings/input/touchscreen/edt-ft5x06.txt
@@ -0,0 +1,55 @@
+FocalTech EDT-FT5x06 Polytouch driver
+=====================================
+
+There are 3 variants of the chip for various touch panel sizes
+FT5206GE1  2.8" .. 3.8"
+FT5306DE4  4.3" .. 7"
+FT5406EE8  7"   .. 8.9"
+
+The software interface is identical for all those chips, so that
+currently there is no need for the driver to distinguish between the
+different chips. Nevertheless distinct compatible strings are used so
+that a distinction can be added if necessary without changing the DT
+bindings.
+
+
+Required properties:
+ - compatible:  "edt,edt-ft5206"
+           or:  "edt,edt-ft5306"
+           or:  "edt,edt-ft5406"
+
+ - reg:         I2C slave address of the chip (0x38)
+ - interrupt-parent: a phandle pointing to the interrupt controller
+                     serving the interrupt for this chip
+ - interrupts:       interrupt specification for the touchdetect
+                     interrupt
+
+Optional properties:
+ - reset-gpios: GPIO specification for the RESET input
+ - wake-gpios:  GPIO specification for the WAKE input
+
+ - pinctrl-names: should be "default"
+ - pinctrl-0:   a phandle pointing to the pin settings for the
+                control gpios
+
+ - threshold:   allows setting the "click"-threshold in the range
+                from 20 to 80.
+
+ - gain:        allows setting the sensitivity in the range from 0 to
+                31. Note that lower values indicate higher
+                sensitivity.
+
+ - offset:      allows setting the edge compensation in the range from
+                0 to 31.
+
+Example:
+	polytouch: edt-ft5x06@38 {
+		compatible = "edt,edt-ft5406", "edt,edt-ft5x06";
+		reg = <0x38>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&edt_ft5x06_pins>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <5 0>;
+		reset-gpios = <&gpio2 6 1>;
+		wake-gpios = <&gpio4 9 0>;
+	};
diff --git a/dts/Bindings/input/touchscreen/egalax-ts.txt b/dts/Bindings/input/touchscreen/egalax-ts.txt
new file mode 100644
index 0000000000..49fa14ed15
--- /dev/null
+++ b/dts/Bindings/input/touchscreen/egalax-ts.txt
@@ -0,0 +1,19 @@
+* EETI eGalax Multiple Touch Controller
+
+Required properties:
+- compatible: must be "eeti,egalax_ts"
+- reg: i2c slave address
+- interrupt-parent: the phandle for the interrupt controller
+- interrupts: touch controller interrupt
+- wakeup-gpios: the gpio pin to be used for waking up the controller
+  and also used as irq pin
+
+Example:
+
+	egalax_ts@04 {
+		compatible = "eeti,egalax_ts";
+		reg = <0x04>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <9 2>;
+		wakeup-gpios = <&gpio1 9 0>;
+	};
diff --git a/dts/Bindings/input/touchscreen/lpc32xx-tsc.txt b/dts/Bindings/input/touchscreen/lpc32xx-tsc.txt
new file mode 100644
index 0000000000..41cbf4b7a6
--- /dev/null
+++ b/dts/Bindings/input/touchscreen/lpc32xx-tsc.txt
@@ -0,0 +1,16 @@
+* NXP LPC32xx SoC Touchscreen Controller (TSC)
+
+Required properties:
+- compatible: must be "nxp,lpc3220-tsc"
+- reg: physical base address of the controller and length of memory mapped
+  region.
+- interrupts: The TSC/ADC interrupt
+
+Example:
+
+	tsc@40048000 {
+		compatible = "nxp,lpc3220-tsc";
+		reg = <0x40048000 0x1000>;
+		interrupt-parent = <&mic>;
+		interrupts = <39 0>;
+	};
diff --git a/dts/Bindings/input/touchscreen/mms114.txt b/dts/Bindings/input/touchscreen/mms114.txt
new file mode 100644
index 0000000000..89d4c56c56
--- /dev/null
+++ b/dts/Bindings/input/touchscreen/mms114.txt
@@ -0,0 +1,34 @@
+* MELFAS MMS114 touchscreen controller
+
+Required properties:
+- compatible: must be "melfas,mms114"
+- reg: I2C address of the chip
+- interrupts: interrupt to which the chip is connected
+- x-size: horizontal resolution of touchscreen
+- y-size: vertical resolution of touchscreen
+
+Optional properties:
+- contact-threshold:
+- moving-threshold:
+- x-invert: invert X axis
+- y-invert: invert Y axis
+
+Example:
+
+	i2c@00000000 {
+		/* ... */
+
+		touchscreen@48 {
+			compatible = "melfas,mms114";
+			reg = <0x48>;
+			interrupts = <39 0>;
+			x-size = <720>;
+			y-size = <1280>;
+			contact-threshold = <10>;
+			moving-threshold = <10>;
+			x-invert;
+			y-invert;
+		};
+
+		/* ... */
+	};
diff --git a/dts/Bindings/input/touchscreen/sitronix-st1232.txt b/dts/Bindings/input/touchscreen/sitronix-st1232.txt
new file mode 100644
index 0000000000..64ad48b824
--- /dev/null
+++ b/dts/Bindings/input/touchscreen/sitronix-st1232.txt
@@ -0,0 +1,24 @@
+* Sitronix st1232 touchscreen controller
+
+Required properties:
+- compatible: must be "sitronix,st1232"
+- reg: I2C address of the chip
+- interrupts: interrupt to which the chip is connected
+
+Optional properties:
+- gpios: a phandle to the reset GPIO
+
+Example:
+
+	i2c@00000000 {
+		/* ... */
+
+		touchscreen@55 {
+			compatible = "sitronix,st1232";
+			reg = <0x55>;
+			interrupts = <2 0>;
+			gpios = <&gpio1 166 0>;
+		};
+
+		/* ... */
+	};
diff --git a/dts/Bindings/input/touchscreen/stmpe.txt b/dts/Bindings/input/touchscreen/stmpe.txt
new file mode 100644
index 0000000000..127baa31a7
--- /dev/null
+++ b/dts/Bindings/input/touchscreen/stmpe.txt
@@ -0,0 +1,43 @@
+STMPE Touchscreen
+----------------
+
+Required properties:
+ - compatible: "st,stmpe-ts"
+
+Optional properties:
+- st,sample-time: ADC converstion time in number of clock.  (0 -> 36 clocks, 1 ->
+  44 clocks, 2 -> 56 clocks, 3 -> 64 clocks, 4 -> 80 clocks, 5 -> 96 clocks, 6
+  -> 144 clocks), recommended is 4.
+- st,mod-12b: ADC Bit mode (0 -> 10bit ADC, 1 -> 12bit ADC)
+- st,ref-sel: ADC reference source (0 -> internal reference, 1 -> external
+  reference)
+- st,adc-freq: ADC Clock speed (0 -> 1.625 MHz, 1 -> 3.25 MHz, 2 || 3 -> 6.5 MHz)
+- st,ave-ctrl: Sample average control (0 -> 1 sample, 1 -> 2 samples, 2 -> 4
+  samples, 3 -> 8 samples)
+- st,touch-det-delay: Touch detect interrupt delay (0 -> 10 us, 1 -> 50 us, 2 ->
+  100 us, 3 -> 500 us, 4-> 1 ms, 5 -> 5 ms, 6 -> 10 ms, 7 -> 50 ms) recommended
+  is 3
+- st,settling: Panel driver settling time (0 -> 10 us, 1 -> 100 us, 2 -> 500 us, 3
+  -> 1 ms, 4 -> 5 ms, 5 -> 10 ms, 6 for 50 ms, 7 -> 100 ms) recommended is 2
+- st,fraction-z: Length of the fractional part in z (fraction-z ([0..7]) = Count of
+  the fractional part) recommended is 7
+- st,i-drive: current limit value of the touchscreen drivers (0 -> 20 mA typical 35
+  mA max, 1 -> 50 mA typical 80 mA max)
+
+Node name must be stmpe_touchscreen and should be child node of stmpe node to
+which it belongs.
+
+Example:
+
+	stmpe_touchscreen {
+		compatible = "st,stmpe-ts";
+		st,sample-time = <4>;
+		st,mod-12b = <1>;
+		st,ref-sel = <0>;
+		st,adc-freq = <1>;
+		st,ave-ctrl = <1>;
+		st,touch-det-delay = <2>;
+		st,settling = <2>;
+		st,fraction-z = <7>;
+		st,i-drive = <1>;
+	};
diff --git a/dts/Bindings/input/touchscreen/ti-tsc-adc.txt b/dts/Bindings/input/touchscreen/ti-tsc-adc.txt
new file mode 100644
index 0000000000..878549ba81
--- /dev/null
+++ b/dts/Bindings/input/touchscreen/ti-tsc-adc.txt
@@ -0,0 +1,44 @@
+* TI - TSC ADC (Touschscreen and analog digital converter)
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Required properties:
+- child "tsc"
+	ti,wires: Wires refer to application modes i.e. 4/5/8 wire touchscreen
+		  support on the platform.
+	ti,x-plate-resistance: X plate resistance
+	ti,coordinate-readouts: The sequencer supports a total of 16
+				programmable steps each step is used to
+				read a single coordinate. A single
+                                readout is enough but multiple reads can
+				increase the quality.
+				A value of 5 means, 5 reads for X, 5 for
+				Y and 2 for Z (always). This utilises 12
+				of the 16 software steps available. The
+				remaining 4 can be used by the ADC.
+	ti,wire-config: Different boards could have a different order for
+			connecting wires on touchscreen. We need to provide an
+			8 bit number where in the 1st four bits represent the
+			analog lines and the next 4 bits represent positive/
+			negative terminal on that input line. Notations to
+			represent the input lines and terminals resoectively
+			is as follows:
+			AIN0 = 0, AIN1 = 1 and so on till AIN7 = 7.
+			XP  = 0, XN = 1, YP = 2, YN = 3.
+- child "adc"
+	ti,adc-channels: List of analog inputs available for ADC.
+			 AIN0 = 0, AIN1 = 1 and so on till AIN7 = 7.
+
+Example:
+	tscadc: tscadc@44e0d000 {
+		compatible = "ti,am3359-tscadc";
+		tsc {
+			ti,wires = <4>;
+			ti,x-plate-resistance = <200>;
+			ti,coordiante-readouts = <5>;
+			ti,wire-config = <0x00 0x11 0x22 0x33>;
+		};
+
+		adc {
+			ti,adc-channels = <4 5 6 7>;
+		};
+	}
diff --git a/dts/Bindings/input/touchscreen/tsc2007.txt b/dts/Bindings/input/touchscreen/tsc2007.txt
new file mode 100644
index 0000000000..ec365e1722
--- /dev/null
+++ b/dts/Bindings/input/touchscreen/tsc2007.txt
@@ -0,0 +1,41 @@
+* Texas Instruments tsc2007 touchscreen controller
+
+Required properties:
+- compatible: must be "ti,tsc2007".
+- reg: I2C address of the chip.
+- ti,x-plate-ohms: X-plate resistance in ohms.
+
+Optional properties:
+- gpios: the interrupt gpio the chip is connected to (trough the penirq pin).
+  The penirq pin goes to low when the panel is touched.
+  (see GPIO binding[1] for more details).
+- interrupt-parent: the phandle for the gpio controller
+  (see interrupt binding[0]).
+- interrupts: (gpio) interrupt to which the chip is connected
+  (see interrupt binding[0]).
+- ti,max-rt: maximum pressure.
+- ti,fuzzx: specifies the absolute input fuzz x value.
+  If set, it will permit noise in the data up to +- the value given to the fuzz
+  parameter, that is used to filter noise from the event stream.
+- ti,fuzzy: specifies the absolute input fuzz y value.
+- ti,fuzzz: specifies the absolute input fuzz z value.
+- ti,poll-period: how much time to wait (in milliseconds) before reading again the
+  values from the tsc2007.
+
+[0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
+[1]: Documentation/devicetree/bindings/gpio/gpio.txt
+
+Example:
+	&i2c1 {
+		/* ... */
+		tsc2007@49 {
+			compatible = "ti,tsc2007";
+			reg = <0x49>;
+			interrupt-parent = <&gpio4>;
+			interrupts = <0x0 0x8>;
+			gpios = <&gpio4 0 0>;
+			ti,x-plate-ohms = <180>;
+		};
+
+		/* ... */
+	};
diff --git a/dts/Bindings/input/touchscreen/zforce_ts.txt b/dts/Bindings/input/touchscreen/zforce_ts.txt
new file mode 100644
index 0000000000..2faf1f1fa3
--- /dev/null
+++ b/dts/Bindings/input/touchscreen/zforce_ts.txt
@@ -0,0 +1,30 @@
+* Neonode infrared touchscreen controller
+
+Required properties:
+- compatible: must be "neonode,zforce"
+- reg: I2C address of the chip
+- interrupts: interrupt to which the chip is connected
+- gpios: gpios the chip is connected to
+  first one is the interrupt gpio and second one the reset gpio
+- x-size: horizontal resolution of touchscreen
+- y-size: vertical resolution of touchscreen
+
+Example:
+
+	i2c@00000000 {
+		/* ... */
+
+		zforce_ts@50 {
+			compatible = "neonode,zforce";
+			reg = <0x50>;
+			interrupts = <2 0>;
+
+			gpios = <&gpio5 6 0>, /* INT */
+				<&gpio5 9 0>; /* RST */
+
+			x-size = <800>;
+			y-size = <600>;
+		};
+
+		/* ... */
+	};
diff --git a/dts/Bindings/input/twl4030-keypad.txt b/dts/Bindings/input/twl4030-keypad.txt
new file mode 100644
index 0000000000..e4be2f76a7
--- /dev/null
+++ b/dts/Bindings/input/twl4030-keypad.txt
@@ -0,0 +1,27 @@
+* TWL4030's Keypad Controller device tree bindings
+
+TWL4030's Keypad controller is used to interface a SoC with a matrix-type
+keypad device. The keypad controller supports multiple row and column lines.
+A key can be placed at each intersection of a unique row and a unique column.
+The keypad controller can sense a key-press and key-release and report the
+event using a interrupt to the cpu.
+
+This binding is based on the matrix-keymap binding with the following
+changes:
+
+ * keypad,num-rows and keypad,num-columns are required.
+
+Required SoC Specific Properties:
+- compatible: should be one of the following
+   - "ti,twl4030-keypad": For controllers compatible with twl4030 keypad
+      controller.
+- interrupt: should be one of the following
+   - <1>: For controllers compatible with twl4030 keypad controller.
+
+Example:
+	twl_keypad: keypad {
+		compatible = "ti,twl4030-keypad";
+		interrupts = <1>;
+		keypad,num-rows = <8>;
+		keypad,num-columns = <8>;
+	};
diff --git a/dts/Bindings/input/twl4030-pwrbutton.txt b/dts/Bindings/input/twl4030-pwrbutton.txt
new file mode 100644
index 0000000000..c864a46cdd
--- /dev/null
+++ b/dts/Bindings/input/twl4030-pwrbutton.txt
@@ -0,0 +1,21 @@
+Texas Instruments TWL family (twl4030) pwrbutton module
+
+This module is part of the TWL4030. For more details about the whole
+chip see Documentation/devicetree/bindings/mfd/twl-familly.txt.
+
+This module provides a simple power button event via an Interrupt.
+
+Required properties:
+- compatible: should be one of the following
+   - "ti,twl4030-pwrbutton": For controllers compatible with twl4030
+- interrupts: should be one of the following
+   - <8>: For controllers compatible with twl4030
+
+Example:
+
+&twl {
+	twl_pwrbutton: pwrbutton {
+		compatible = "ti,twl4030-pwrbutton";
+		interrupts = <8>;
+	};
+};