dts: update to v4.3-rc1

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

14 files changed, 154 insertions, 10 deletions

diff --git a/dts/Bindings/input/ads7846.txt b/dts/Bindings/input/ads7846.txt
index 5f7619c227..df8b127949 100644
--- a/dts/Bindings/input/ads7846.txt
+++ b/dts/Bindings/input/ads7846.txt
@@ -64,7 +64,7 @@ Optional properties:
 					pendown-gpio (u32).
 	pendown-gpio			GPIO handle describing the pin the !PENIRQ
 					line is connected to.
-	linux,wakeup			use any event on touchscreen as wakeup event.
+	wakeup-source			use any event on touchscreen as wakeup event.
 
 
 Example for a TSC2046 chip connected to an McSPI controller of an OMAP SoC::
diff --git a/dts/Bindings/input/cap11xx.txt b/dts/Bindings/input/cap11xx.txt
index 7d0a300977..8c67a0b505 100644
--- a/dts/Bindings/input/cap11xx.txt
+++ b/dts/Bindings/input/cap11xx.txt
@@ -55,5 +55,24 @@ i2c_controller {
 				 <105>,		/* KEY_LEFT */
 				 <109>,		/* KEY_PAGEDOWN */
 				 <104>;		/* KEY_PAGEUP */
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		usr@0 {
+			label = "cap11xx:green:usr0";
+			reg = <0>;
+		};
+
+		usr@1 {
+			label = "cap11xx:green:usr1";
+			reg = <1>;
+		};
+
+		alive@2 {
+			label = "cap11xx:green:alive";
+			reg = <2>;
+			linux,default_trigger = "heartbeat";
+		};
 	};
 }
diff --git a/dts/Bindings/input/cypress,cyapa.txt b/dts/Bindings/input/cypress,cyapa.txt
new file mode 100644
index 0000000000..635a3b0366
--- /dev/null
+++ b/dts/Bindings/input/cypress,cyapa.txt
@@ -0,0 +1,44 @@
+Cypress I2C Touchpad
+
+Required properties:
+- compatible: must be "cypress,cyapa".
+- reg: I2C address of the chip.
+- interrupt-parent: a phandle for the interrupt controller (see interrupt
+	binding[0]).
+- interrupts: interrupt to which the chip is connected (see interrupt
+	binding[0]).
+
+Optional properties:
+- wakeup-source: touchpad can be used as a wakeup source.
+- pinctrl-names: should be "default" (see pinctrl binding [1]).
+- pinctrl-0: a phandle pointing to the pin settings for the device (see
+	pinctrl binding [1]).
+- vcc-supply: a phandle for the regulator supplying 3.3V power.
+
+[0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
+[1]: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
+
+Example:
+	&i2c0 {
+		/* ... */
+
+		/* Cypress Gen3 touchpad */
+		touchpad@67 {
+			compatible = "cypress,cyapa";
+			reg = <0x24>;
+			interrupt-parent = <&gpio>;
+			interrupts = <2 IRQ_TYPE_EDGE_FALLING>;	/* GPIO 2 */
+			wakeup-source;
+		};
+
+		/* Cypress Gen5 and later touchpad */
+		touchpad@24 {
+			compatible = "cypress,cyapa";
+			reg = <0x24>;
+			interrupt-parent = <&gpio>;
+			interrupts = <2 IRQ_TYPE_EDGE_FALLING>;	/* GPIO 2 */
+			wakeup-source;
+		};
+
+		/* ... */
+	};
diff --git a/dts/Bindings/input/elants_i2c.txt b/dts/Bindings/input/elants_i2c.txt
index a765232e64..8a71038f34 100644
--- a/dts/Bindings/input/elants_i2c.txt
+++ b/dts/Bindings/input/elants_i2c.txt
@@ -13,6 +13,9 @@ Optional properties:
 - pinctrl-names: should be "default" (see pinctrl binding [1]).
 - pinctrl-0: a phandle pointing to the pin settings for the device (see
   pinctrl binding [1]).
+- reset-gpios: reset gpio the chip is connected to.
+- vcc33-supply: a phandle for the regulator supplying 3.3V power.
+- vccio-supply: a phandle for the regulator supplying IO power.
 
 [0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
 [1]: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
diff --git a/dts/Bindings/input/gpio-keys-polled.txt b/dts/Bindings/input/gpio-keys-polled.txt
index 313abefa37..5b91f5a3bd 100644
--- a/dts/Bindings/input/gpio-keys-polled.txt
+++ b/dts/Bindings/input/gpio-keys-polled.txt
@@ -20,7 +20,7 @@ Optional subnode-properties:
 	  If not specified defaults to <1> == EV_KEY.
 	- debounce-interval: Debouncing interval time in milliseconds.
 	  If not specified defaults to 5.
-	- gpio-key,wakeup: Boolean, button can wake-up the system.
+	- wakeup-source: Boolean, button can wake-up the system.
 
 Example nodes:
 
diff --git a/dts/Bindings/input/gpio-keys.txt b/dts/Bindings/input/gpio-keys.txt
index 44b705767a..072bf7573c 100644
--- a/dts/Bindings/input/gpio-keys.txt
+++ b/dts/Bindings/input/gpio-keys.txt
@@ -23,7 +23,7 @@ Optional subnode-properties:
 	  If not specified defaults to <1> == EV_KEY.
 	- debounce-interval: Debouncing interval time in milliseconds.
 	  If not specified defaults to 5.
-	- gpio-key,wakeup: Boolean, button can wake-up the system.
+	- wakeup-source: Boolean, button can wake-up the system.
 	- linux,can-disable: Boolean, indicates that button is connected
 	  to dedicated (not shared) interrupt which can be disabled to
 	  suppress events from the button.
diff --git a/dts/Bindings/input/gpio-matrix-keypad.txt b/dts/Bindings/input/gpio-matrix-keypad.txt
index ead641c65e..4d86059c37 100644
--- a/dts/Bindings/input/gpio-matrix-keypad.txt
+++ b/dts/Bindings/input/gpio-matrix-keypad.txt
@@ -19,7 +19,7 @@ Required Properties:
 
 Optional Properties:
 - linux,no-autorepeat:	do no enable autorepeat feature.
-- linux,wakeup:		use any event on keypad as wakeup event.
+- wakeup-source:	use any event on keypad as wakeup event.
 - debounce-delay-ms:	debounce interval in milliseconds
 - col-scan-delay-us:	delay, measured in microseconds, that is needed
 			before we can scan keypad after activating column gpio
diff --git a/dts/Bindings/input/qcom,pm8xxx-keypad.txt b/dts/Bindings/input/qcom,pm8xxx-keypad.txt
index 7d8cb92831..ee62156811 100644
--- a/dts/Bindings/input/qcom,pm8xxx-keypad.txt
+++ b/dts/Bindings/input/qcom,pm8xxx-keypad.txt
@@ -33,7 +33,7 @@ PROPERTIES
 	Value type: <bool>
 	Definition: don't enable autorepeat feature.
 
-- linux,keypad-wakeup:
+- wakeup-source:
 	Usage: optional
 	Value type: <bool>
 	Definition: use any event on keypad as wakeup event.
diff --git a/dts/Bindings/input/samsung-keypad.txt b/dts/Bindings/input/samsung-keypad.txt
index 942d071baa..863e77f619 100644
--- a/dts/Bindings/input/samsung-keypad.txt
+++ b/dts/Bindings/input/samsung-keypad.txt
@@ -36,9 +36,11 @@ Required Board Specific Properties:
 - pinctrl-0: Should specify pin control groups used for this controller.
 - pinctrl-names: Should contain only one value - "default".
 
+Optional Properties:
+- wakeup-source: use any event on keypad as wakeup event.
+
 Optional Properties specific to linux:
 - linux,keypad-no-autorepeat: do no enable autorepeat feature.
-- linux,keypad-wakeup: use any event on keypad as wakeup event.
 
 
 Example:
diff --git a/dts/Bindings/input/snvs-pwrkey.txt b/dts/Bindings/input/snvs-pwrkey.txt
new file mode 100644
index 0000000000..70c1425032
--- /dev/null
+++ b/dts/Bindings/input/snvs-pwrkey.txt
@@ -0,0 +1 @@
+See Documentation/devicetree/bindings/crypto/fsl-sec4.txt
diff --git a/dts/Bindings/input/touchscreen/colibri-vf50-ts.txt b/dts/Bindings/input/touchscreen/colibri-vf50-ts.txt
new file mode 100644
index 0000000000..9d9e930f32
--- /dev/null
+++ b/dts/Bindings/input/touchscreen/colibri-vf50-ts.txt
@@ -0,0 +1,36 @@
+* Toradex Colibri VF50 Touchscreen driver
+
+Required Properties:
+- compatible must be toradex,vf50-touchscreen
+- io-channels: adc channels being used by the Colibri VF50 module
+- xp-gpios: FET gate driver for input of X+
+- xm-gpios: FET gate driver for input of X-
+- yp-gpios: FET gate driver for input of Y+
+- ym-gpios: FET gate driver for input of Y-
+- interrupt-parent: phandle for the interrupt controller
+- interrupts: pen irq interrupt for touch detection
+- pinctrl-names: "idle", "default", "gpios"
+- pinctrl-0: pinctrl node for pen/touch detection state pinmux
+- pinctrl-1: pinctrl node for X/Y and pressure measurement (ADC) state pinmux
+- pinctrl-2: pinctrl node for gpios functioning as FET gate drivers
+- vf50-ts-min-pressure: pressure level at which to stop measuring X/Y values
+
+Example:
+
+	touchctrl: vf50_touchctrl {
+		compatible = "toradex,vf50-touchscreen";
+		io-channels = <&adc1 0>,<&adc0 0>,
+				<&adc0 1>,<&adc1 2>;
+		xp-gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
+		xm-gpios = <&gpio2 29 GPIO_ACTIVE_HIGH>;
+		yp-gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
+		ym-gpios = <&gpio0 4 GPIO_ACTIVE_HIGH>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "idle","default","gpios";
+		pinctrl-0 = <&pinctrl_touchctrl_idle>;
+		pinctrl-1 = <&pinctrl_touchctrl_default>;
+		pinctrl-2 = <&pinctrl_touchctrl_gpios>;
+		vf50-ts-min-pressure = <200>;
+		status = "disabled";
+	};
diff --git a/dts/Bindings/input/touchscreen/imx6ul_tsc.txt b/dts/Bindings/input/touchscreen/imx6ul_tsc.txt
new file mode 100644
index 0000000000..853dff96dd
--- /dev/null
+++ b/dts/Bindings/input/touchscreen/imx6ul_tsc.txt
@@ -0,0 +1,36 @@
+* Freescale i.MX6UL Touch Controller
+
+Required properties:
+- compatible: must be "fsl,imx6ul-tsc".
+- reg: this touch controller address and the ADC2 address.
+- interrupts: the interrupt of this touch controller and ADC2.
+- clocks: the root clock of touch controller and ADC2.
+- clock-names; must be "tsc" and "adc".
+- xnur-gpio: the X- gpio this controller connect to.
+  This xnur-gpio returns to low once the finger leave the touch screen (The
+  last touch event the touch controller capture).
+
+Optional properties:
+- measure-delay-time: the value of measure delay time.
+  Before X-axis or Y-axis measurement, the screen need some time before
+  even potential distribution ready.
+  This value depends on the touch screen.
+- pre-charge-time: the touch screen need some time to precharge.
+  This value depends on the touch screen.
+
+Example:
+	tsc: tsc@02040000 {
+		compatible = "fsl,imx6ul-tsc";
+		reg = <0x02040000 0x4000>, <0x0219c000 0x4000>;
+		interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&clks IMX6UL_CLK_IPG>,
+			 <&clks IMX6UL_CLK_ADC2>;
+		clock-names = "tsc", "adc";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_tsc>;
+		xnur-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>;
+		measure-delay-time = <0xfff>;
+		pre-charge-time = <0xffff>;
+		status = "okay";
+	};
diff --git a/dts/Bindings/input/touchscreen/pixcir_i2c_ts.txt b/dts/Bindings/input/touchscreen/pixcir_i2c_ts.txt
index 6e551090f4..8eb240a287 100644
--- a/dts/Bindings/input/touchscreen/pixcir_i2c_ts.txt
+++ b/dts/Bindings/input/touchscreen/pixcir_i2c_ts.txt
@@ -8,6 +8,9 @@ Required properties:
 - touchscreen-size-x: horizontal resolution of touchscreen (in pixels)
 - touchscreen-size-y: vertical resolution of touchscreen (in pixels)
 
+Optional properties:
+- reset-gpio: GPIO connected to the RESET line of the chip
+
 Example:
 
 	i2c@00000000 {
diff --git a/dts/Bindings/input/touchscreen/zforce_ts.txt b/dts/Bindings/input/touchscreen/zforce_ts.txt
index 80c37df940..e3c27c4fd9 100644
--- a/dts/Bindings/input/touchscreen/zforce_ts.txt
+++ b/dts/Bindings/input/touchscreen/zforce_ts.txt
@@ -4,12 +4,12 @@ Required properties:
 - compatible: must be "neonode,zforce"
 - reg: I2C address of the chip
 - interrupts: interrupt to which the chip is connected
-- gpios: gpios the chip is connected to
-  first one is the interrupt gpio and second one the reset gpio
+- reset-gpios: reset gpio the chip is connected to
 - x-size: horizontal resolution of touchscreen
 - y-size: vertical resolution of touchscreen
 
 Optional properties:
+- irq-gpios : interrupt gpio the chip is connected to
 - vdd-supply: Regulator controlling the controller supply
 
 Example:
@@ -23,8 +23,8 @@ Example:
 			interrupts = <2 0>;
 			vdd-supply = <&reg_zforce_vdd>;
 
-			gpios = <&gpio5 6 0>, /* INT */
-				<&gpio5 9 0>; /* RST */
+			reset-gpios = <&gpio5 9 0>; /* RST */
+			irq-gpios = <&gpio5 6 0>; /* IRQ, optional */
 
 			x-size = <800>;
 			y-size = <600>;