summaryrefslogtreecommitdiffstats
path: root/dts/Bindings/interrupt-controller/arm,gic.txt
diff options
context:
space:
mode:
authorSascha Hauer <s.hauer@pengutronix.de>2015-12-08 07:35:17 +0100
committerSascha Hauer <s.hauer@pengutronix.de>2015-12-10 08:48:40 +0100
commit6e6d9a2ff045f09d5a03e876becea5e6a1dabe90 (patch)
treebcf5e71df4472e374d03cc15ca22b4f841d9c73d /dts/Bindings/interrupt-controller/arm,gic.txt
parent8e2fd5380a4fd7cee428513dc8eab068912b49f1 (diff)
downloadbarebox-6e6d9a2ff045f09d5a03e876becea5e6a1dabe90.tar.gz
dts: update to v4.4-rc1
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Diffstat (limited to 'dts/Bindings/interrupt-controller/arm,gic.txt')
-rw-r--r--dts/Bindings/interrupt-controller/arm,gic.txt168
1 files changed, 168 insertions, 0 deletions
diff --git a/dts/Bindings/interrupt-controller/arm,gic.txt b/dts/Bindings/interrupt-controller/arm,gic.txt
new file mode 100644
index 0000000..cc56021
--- /dev/null
+++ b/dts/Bindings/interrupt-controller/arm,gic.txt
@@ -0,0 +1,168 @@
+* ARM Generic Interrupt Controller
+
+ARM SMP cores are often associated with a GIC, providing per processor
+interrupts (PPI), shared processor interrupts (SPI) and software
+generated interrupts (SGI).
+
+Primary GIC is attached directly to the CPU and typically has PPIs and SGIs.
+Secondary GICs are cascaded into the upward interrupt controller and do not
+have PPIs or SGIs.
+
+Main node required properties:
+
+- compatible : should be one of:
+ "arm,arm1176jzf-devchip-gic"
+ "arm,arm11mp-gic"
+ "arm,cortex-a15-gic"
+ "arm,cortex-a7-gic"
+ "arm,cortex-a9-gic"
+ "arm,gic-400"
+ "arm,pl390"
+ "brcm,brahma-b15-gic"
+ "qcom,msm-8660-qgic"
+ "qcom,msm-qgic2"
+- interrupt-controller : Identifies the node as an interrupt controller
+- #interrupt-cells : Specifies the number of cells needed to encode an
+ interrupt source. The type shall be a <u32> and the value shall be 3.
+
+ The 1st cell is the interrupt type; 0 for SPI interrupts, 1 for PPI
+ interrupts.
+
+ The 2nd cell contains the interrupt number for the interrupt type.
+ SPI interrupts are in the range [0-987]. PPI interrupts are in the
+ range [0-15].
+
+ The 3rd cell is the flags, encoded as follows:
+ bits[3:0] trigger type and level flags.
+ 1 = low-to-high edge triggered
+ 2 = high-to-low edge triggered (invalid for SPIs)
+ 4 = active high level-sensitive
+ 8 = active low level-sensitive (invalid for SPIs).
+ bits[15:8] PPI interrupt cpu mask. Each bit corresponds to each of
+ the 8 possible cpus attached to the GIC. A bit set to '1' indicated
+ the interrupt is wired to that CPU. Only valid for PPI interrupts.
+ Also note that the configurability of PPI interrupts is IMPLEMENTATION
+ DEFINED and as such not guaranteed to be present (most SoC available
+ in 2014 seem to ignore the setting of this flag and use the hardware
+ default value).
+
+- reg : Specifies base physical address(s) and size of the GIC registers. The
+ first region is the GIC distributor register base and size. The 2nd region is
+ the GIC cpu interface register base and size.
+
+Optional
+- interrupts : Interrupt source of the parent interrupt controller on
+ secondary GICs, or VGIC maintenance interrupt on primary GIC (see
+ below).
+
+- cpu-offset : per-cpu offset within the distributor and cpu interface
+ regions, used when the GIC doesn't have banked registers. The offset is
+ cpu-offset * cpu-nr.
+
+- clocks : List of phandle and clock-specific pairs, one for each entry
+ in clock-names.
+- clock-names : List of names for the GIC clock input(s). Valid clock names
+ depend on the GIC variant:
+ "ic_clk" (for "arm,arm11mp-gic")
+ "PERIPHCLKEN" (for "arm,cortex-a15-gic")
+ "PERIPHCLK", "PERIPHCLKEN" (for "arm,cortex-a9-gic")
+ "clk" (for "arm,gic-400")
+ "gclk" (for "arm,pl390")
+
+- power-domains : A phandle and PM domain specifier as defined by bindings of
+ the power controller specified by phandle, used when the GIC
+ is part of a Power or Clock Domain.
+
+
+Example:
+
+ intc: interrupt-controller@fff11000 {
+ compatible = "arm,cortex-a9-gic";
+ #interrupt-cells = <3>;
+ #address-cells = <1>;
+ interrupt-controller;
+ reg = <0xfff11000 0x1000>,
+ <0xfff10100 0x100>;
+ };
+
+
+* GIC virtualization extensions (VGIC)
+
+For ARM cores that support the virtualization extensions, additional
+properties must be described (they only exist if the GIC is the
+primary interrupt controller).
+
+Required properties:
+
+- reg : Additional regions specifying the base physical address and
+ size of the VGIC registers. The first additional region is the GIC
+ virtual interface control register base and size. The 2nd additional
+ region is the GIC virtual cpu interface register base and size.
+
+- interrupts : VGIC maintenance interrupt.
+
+Example:
+
+ interrupt-controller@2c001000 {
+ compatible = "arm,cortex-a15-gic";
+ #interrupt-cells = <3>;
+ interrupt-controller;
+ reg = <0x2c001000 0x1000>,
+ <0x2c002000 0x1000>,
+ <0x2c004000 0x2000>,
+ <0x2c006000 0x2000>;
+ interrupts = <1 9 0xf04>;
+ };
+
+
+* GICv2m extension for MSI/MSI-x support (Optional)
+
+Certain revisions of GIC-400 supports MSI/MSI-x via V2M register frame(s).
+This is enabled by specifying v2m sub-node(s).
+
+Required properties:
+
+- compatible : The value here should contain "arm,gic-v2m-frame".
+
+- msi-controller : Identifies the node as an MSI controller.
+
+- reg : GICv2m MSI interface register base and size
+
+Optional properties:
+
+- arm,msi-base-spi : When the MSI_TYPER register contains an incorrect
+ value, this property should contain the SPI base of
+ the MSI frame, overriding the HW value.
+
+- arm,msi-num-spis : When the MSI_TYPER register contains an incorrect
+ value, this property should contain the number of
+ SPIs assigned to the frame, overriding the HW value.
+
+Example:
+
+ interrupt-controller@e1101000 {
+ compatible = "arm,gic-400";
+ #interrupt-cells = <3>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-controller;
+ interrupts = <1 8 0xf04>;
+ ranges = <0 0 0 0xe1100000 0 0x100000>;
+ reg = <0x0 0xe1110000 0 0x01000>,
+ <0x0 0xe112f000 0 0x02000>,
+ <0x0 0xe1140000 0 0x10000>,
+ <0x0 0xe1160000 0 0x10000>;
+ v2m0: v2m@0x8000 {
+ compatible = "arm,gic-v2m-frame";
+ msi-controller;
+ reg = <0x0 0x80000 0 0x1000>;
+ };
+
+ ....
+
+ v2mN: v2m@0x9000 {
+ compatible = "arm,gic-v2m-frame";
+ msi-controller;
+ reg = <0x0 0x90000 0 0x1000>;
+ };
+ };