dts: update to v4.8-rc1

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

3 files changed, 74 insertions, 5 deletions

diff --git a/dts/Bindings/iommu/arm,smmu-v3.txt b/dts/Bindings/iommu/arm,smmu-v3.txt
index 947863acc2..7b94c88cf2 100644
--- a/dts/Bindings/iommu/arm,smmu-v3.txt
+++ b/dts/Bindings/iommu/arm,smmu-v3.txt
@@ -1,6 +1,6 @@
 * ARM SMMUv3 Architecture Implementation
 
-The SMMUv3 architecture is a significant deparature from previous
+The SMMUv3 architecture is a significant departure from previous
 revisions, replacing the MMIO register interface with in-memory command
 and event queues and adding support for the ATS and PRI components of
 the PCIe specification.
diff --git a/dts/Bindings/iommu/mediatek,iommu.txt b/dts/Bindings/iommu/mediatek,iommu.txt
index cd1b1cd7b5..53c20cae30 100644
--- a/dts/Bindings/iommu/mediatek,iommu.txt
+++ b/dts/Bindings/iommu/mediatek,iommu.txt
@@ -1,7 +1,9 @@
 * Mediatek IOMMU Architecture Implementation
 
-  Some Mediatek SOCs contain a Multimedia Memory Management Unit (M4U) which
-uses the ARM Short-Descriptor translation table format for address translation.
+  Some Mediatek SOCs contain a Multimedia Memory Management Unit (M4U), and
+this M4U have two generations of HW architecture. Generation one uses flat
+pagetable, and only supports 4K size page mapping. Generation two uses the
+ARM Short-Descriptor translation table format for address translation.
 
   About the M4U Hardware Block Diagram, please check below:
 
@@ -36,7 +38,9 @@ in each larb. Take a example, There are many ports like MC, PP, VLD in the
 video decode local arbiter, all these ports are according to the video HW.
 
 Required properties:
-- compatible : must be "mediatek,mt8173-m4u".
+- compatible : must be one of the following string:
+	"mediatek,mt2701-m4u" for mt2701 which uses generation one m4u HW.
+	"mediatek,mt8173-m4u" for mt8173 which uses generation two m4u HW.
 - reg : m4u register base and size.
 - interrupts : the interrupt of m4u.
 - clocks : must contain one entry for each clock-names.
@@ -46,7 +50,8 @@ Required properties:
 	according to the local arbiter index, like larb0, larb1, larb2...
 - iommu-cells : must be 1. This is the mtk_m4u_id according to the HW.
 	Specifies the mtk_m4u_id as defined in
-	dt-binding/memory/mt8173-larb-port.h.
+	dt-binding/memory/mt2701-larb-port.h for mt2701 and
+	dt-binding/memory/mt8173-larb-port.h for mt8173
 
 Example:
 	iommu: iommu@10205000 {
diff --git a/dts/Bindings/iommu/msm,iommu-v0.txt b/dts/Bindings/iommu/msm,iommu-v0.txt
new file mode 100644
index 0000000000..20236385f2
--- /dev/null
+++ b/dts/Bindings/iommu/msm,iommu-v0.txt
@@ -0,0 +1,64 @@
+* QCOM IOMMU
+
+The MSM IOMMU is an implementation compatible with the ARM VMSA short
+descriptor page tables. It provides address translation for bus masters outside
+of the CPU, each connected to the IOMMU through a port called micro-TLB.
+
+Required Properties:
+
+  - compatible: Must contain "qcom,apq8064-iommu".
+  - reg: Base address and size of the IOMMU registers.
+  - interrupts: Specifiers for the MMU fault interrupts. For instances that
+    support secure mode two interrupts must be specified, for non-secure and
+    secure mode, in that order. For instances that don't support secure mode a
+    single interrupt must be specified.
+  - #iommu-cells: The number of cells needed to specify the stream id. This
+		  is always 1.
+  - qcom,ncb:	  The total number of context banks in the IOMMU.
+  - clocks	: List of clocks to be used during SMMU register access. See
+		  Documentation/devicetree/bindings/clock/clock-bindings.txt
+		  for information about the format. For each clock specified
+		  here, there must be a corresponding entry in clock-names
+		  (see below).
+
+  - clock-names	: List of clock names corresponding to the clocks specified in
+		  the "clocks" property (above).
+		  Should be "smmu_pclk" for specifying the interface clock
+		  required for iommu's register accesses.
+		  Should be "smmu_clk" for specifying the functional clock
+		  required by iommu for bus accesses.
+
+Each bus master connected to an IOMMU must reference the IOMMU in its device
+node with the following property:
+
+  - iommus: A reference to the IOMMU in multiple cells. The first cell is a
+	    phandle to the IOMMU and the second cell is the stream id.
+	    A single master device can be connected to more than one iommu
+	    and multiple contexts in each of the iommu. So multiple entries
+	    are required to list all the iommus and the stream ids that the
+	    master is connected to.
+
+Example: mdp iommu and its bus master
+
+                mdp_port0: iommu@7500000 {
+			compatible = "qcom,apq8064-iommu";
+			#iommu-cells = <1>;
+			clock-names =
+			    "smmu_pclk",
+			    "smmu_clk";
+			clocks =
+			    <&mmcc SMMU_AHB_CLK>,
+			    <&mmcc MDP_AXI_CLK>;
+			reg = <0x07500000 0x100000>;
+			interrupts =
+			    <GIC_SPI 63 0>,
+			    <GIC_SPI 64 0>;
+			qcom,ncb = <2>;
+		};
+
+		mdp: qcom,mdp@5100000 {
+			compatible = "qcom,mdp";
+			...
+			iommus = <&mdp_port0 0
+				  &mdp_port0 2>;
+		};