dts: update to v5.17-rc1

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

3 files changed, 563 insertions, 319 deletions

diff --git a/dts/Bindings/leds/leds-bcm6328.txt b/dts/Bindings/leds/leds-bcm6328.txt
deleted file mode 100644
index a555d94084..0000000000
--- a/dts/Bindings/leds/leds-bcm6328.txt
+++ /dev/null
@@ -1,319 +0,0 @@
-LEDs connected to Broadcom BCM6328 controller
-
-This controller is present on BCM6318, BCM6328, BCM6362 and BCM63268.
-In these SoCs it's possible to control LEDs both as GPIOs or by hardware.
-However, on some devices there are Serial LEDs (LEDs connected to a 74x164
-controller), which can either be controlled by software (exporting the 74x164
-as spi-gpio. See Documentation/devicetree/bindings/gpio/fairchild,74hc595.yaml),
-or by hardware using this driver.
-Some of these Serial LEDs are hardware controlled (e.g. ethernet LEDs) and
-exporting the 74x164 as spi-gpio prevents those LEDs to be hardware
-controlled, so the only chance to keep them working is by using this driver.
-
-BCM6328 LED controller has a HWDIS register, which controls whether a LED
-should be controlled by a hardware signal instead of the MODE register value,
-with 0 meaning hardware control enabled and 1 hardware control disabled. This
-is usually 1:1 for hardware to LED signals, but through the activity/link
-registers you have some limited control over rerouting the LEDs (as
-explained later in brcm,link-signal-sources). Even if a LED is hardware
-controlled you are still able to make it blink or light it up if it isn't,
-but you can't turn it off if the hardware decides to light it up. For this
-reason, hardware controlled LEDs aren't registered as LED class devices.
-
-Required properties:
-  - compatible : should be "brcm,bcm6328-leds".
-  - #address-cells : must be 1.
-  - #size-cells : must be 0.
-  - reg : BCM6328 LED controller address and size.
-
-Optional properties:
-  - brcm,serial-leds : Boolean, enables Serial LEDs.
-    Default : false
-  - brcm,serial-mux : Boolean, enables Serial LEDs multiplexing.
-    Default : false
-  - brcm,serial-clk-low : Boolean, makes clock signal active low.
-    Default : false
-  - brcm,serial-dat-low : Boolean, makes data signal active low.
-    Default : false
-  - brcm,serial-shift-inv : Boolean, inverts Serial LEDs shift direction.
-    Default : false
-
-Each LED is represented as a sub-node of the brcm,bcm6328-leds device.
-
-LED sub-node required properties:
-  - reg : LED pin number (only LEDs 0 to 23 are valid).
-
-LED sub-node optional properties:
-  a) Optional properties for sub-nodes related to software controlled LEDs:
-    - label : see Documentation/devicetree/bindings/leds/common.txt
-    - active-low : Boolean, makes LED active low.
-      Default : false
-    - default-state : see
-      Documentation/devicetree/bindings/leds/common.txt
-    - linux,default-trigger : see
-      Documentation/devicetree/bindings/leds/common.txt
-
-  b) Optional properties for sub-nodes related to hardware controlled LEDs:
-    - brcm,hardware-controlled : Boolean, makes this LED hardware controlled.
-      Default : false
-    - brcm,link-signal-sources : An array of hardware link
-      signal sources. Up to four link hardware signals can get muxed into
-      these LEDs. Only valid for LEDs 0 to 7, where LED signals 0 to 3 may
-      be muxed to LEDs 0 to 3, and signals 4 to 7 may be muxed to LEDs
-      4 to 7. A signal can be muxed to more than one LED, and one LED can
-      have more than one source signal.
-    - brcm,activity-signal-sources : An array of hardware activity
-      signal sources. Up to four activity hardware signals can get muxed into
-      these LEDs. Only valid for LEDs 0 to 7, where LED signals 0 to 3 may
-      be muxed to LEDs 0 to 3, and signals 4 to 7 may be muxed to LEDs
-      4 to 7. A signal can be muxed to more than one LED, and one LED can
-      have more than one source signal.
-
-Examples:
-Scenario 1 : BCM6328 with 4 EPHY LEDs
-	leds0: led-controller@10000800 {
-		compatible = "brcm,bcm6328-leds";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0x10000800 0x24>;
-
-		alarm_red@2 {
-			reg = <2>;
-			active-low;
-			label = "red:alarm";
-		};
-		inet_green@3 {
-			reg = <3>;
-			active-low;
-			label = "green:inet";
-		};
-		power_green@4 {
-			reg = <4>;
-			active-low;
-			label = "green:power";
-			default-state = "on";
-		};
-		ephy0_spd@17 {
-			reg = <17>;
-			brcm,hardware-controlled;
-		};
-		ephy1_spd@18 {
-			reg = <18>;
-			brcm,hardware-controlled;
-		};
-		ephy2_spd@19 {
-			reg = <19>;
-			brcm,hardware-controlled;
-		};
-		ephy3_spd@20 {
-			reg = <20>;
-			brcm,hardware-controlled;
-		};
-	};
-
-Scenario 2 : BCM63268 with Serial/GPHY0 LEDs
-	leds0: led-controller@10001900 {
-		compatible = "brcm,bcm6328-leds";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0x10001900 0x24>;
-		brcm,serial-leds;
-		brcm,serial-dat-low;
-		brcm,serial-shift-inv;
-
-		gphy0_spd0@0 {
-			reg = <0>;
-			brcm,hardware-controlled;
-			brcm,link-signal-sources = <0>;
-		};
-		gphy0_spd1@1 {
-			reg = <1>;
-			brcm,hardware-controlled;
-			brcm,link-signal-sources = <1>;
-		};
-		inet_red@2 {
-			reg = <2>;
-			active-low;
-			label = "red:inet";
-		};
-		dsl_green@3 {
-			reg = <3>;
-			active-low;
-			label = "green:dsl";
-		};
-		usb_green@4 {
-			reg = <4>;
-			active-low;
-			label = "green:usb";
-		};
-		wps_green@7 {
-			reg = <7>;
-			active-low;
-			label = "green:wps";
-		};
-		inet_green@8 {
-			reg = <8>;
-			active-low;
-			label = "green:inet";
-		};
-		ephy0_act@9 {
-			reg = <9>;
-			brcm,hardware-controlled;
-		};
-		ephy1_act@10 {
-			reg = <10>;
-			brcm,hardware-controlled;
-		};
-		ephy2_act@11 {
-			reg = <11>;
-			brcm,hardware-controlled;
-		};
-		gphy0_act@12 {
-			reg = <12>;
-			brcm,hardware-controlled;
-		};
-		ephy0_spd@13 {
-			reg = <13>;
-			brcm,hardware-controlled;
-		};
-		ephy1_spd@14 {
-			reg = <14>;
-			brcm,hardware-controlled;
-		};
-		ephy2_spd@15 {
-			reg = <15>;
-			brcm,hardware-controlled;
-		};
-		power_green@20 {
-			reg = <20>;
-			active-low;
-			label = "green:power";
-			default-state = "on";
-		};
-	};
-
-Scenario 3 : BCM6362 with 1 LED for each EPHY
-	leds0: led-controller@10001900 {
-		compatible = "brcm,bcm6328-leds";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0x10001900 0x24>;
-
-		usb@0 {
-			reg = <0>;
-			brcm,hardware-controlled;
-			brcm,link-signal-sources = <0>;
-			brcm,activity-signal-sources = <0>;
-			/* USB link/activity routed to USB LED */
-		};
-		inet@1 {
-			reg = <1>;
-			brcm,hardware-controlled;
-			brcm,activity-signal-sources = <1>;
-			/* INET activity routed to INET LED */
-		};
-		ephy0@4 {
-			reg = <4>;
-			brcm,hardware-controlled;
-			brcm,link-signal-sources = <4>;
-			/* EPHY0 link routed to EPHY0 LED */
-		};
-		ephy1@5 {
-			reg = <5>;
-			brcm,hardware-controlled;
-			brcm,link-signal-sources = <5>;
-			/* EPHY1 link routed to EPHY1 LED */
-		};
-		ephy2@6 {
-			reg = <6>;
-			brcm,hardware-controlled;
-			brcm,link-signal-sources = <6>;
-			/* EPHY2 link routed to EPHY2 LED */
-		};
-		ephy3@7 {
-			reg = <7>;
-			brcm,hardware-controlled;
-			brcm,link-signal-sources = <7>;
-			/* EPHY3 link routed to EPHY3 LED */
-		};
-		power_green@20 {
-			reg = <20>;
-			active-low;
-			label = "green:power";
-			default-state = "on";
-		};
-	};
-
-Scenario 4 : BCM6362 with 1 LED for all EPHYs
-	leds0: led-controller@10001900 {
-		compatible = "brcm,bcm6328-leds";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0x10001900 0x24>;
-
-		usb@0 {
-			reg = <0>;
-			brcm,hardware-controlled;
-			brcm,link-signal-sources = <0 1>;
-			brcm,activity-signal-sources = <0 1>;
-			/* USB/INET link/activity routed to USB LED */
-		};
-		ephy@4 {
-			reg = <4>;
-			brcm,hardware-controlled;
-			brcm,link-signal-sources = <4 5 6 7>;
-			/* EPHY0/1/2/3 link routed to EPHY0 LED */
-		};
-		power_green@20 {
-			reg = <20>;
-			active-low;
-			label = "green:power";
-			default-state = "on";
-		};
-	};
-
-Scenario 5 : BCM6362 with EPHY LEDs swapped
-	leds0: led-controller@10001900 {
-		compatible = "brcm,bcm6328-leds";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0x10001900 0x24>;
-
-		usb@0 {
-			reg = <0>;
-			brcm,hardware-controlled;
-			brcm,link-signal-sources = <0>;
-			brcm,activity-signal-sources = <0 1>;
-			/* USB link/act and INET act routed to USB LED */
-		};
-		ephy0@4 {
-			reg = <4>;
-			brcm,hardware-controlled;
-			brcm,link-signal-sources = <7>;
-			/* EPHY3 link routed to EPHY0 LED */
-		};
-		ephy1@5 {
-			reg = <5>;
-			brcm,hardware-controlled;
-			brcm,link-signal-sources = <6>;
-			/* EPHY2 link routed to EPHY1 LED */
-		};
-		ephy2@6 {
-			reg = <6>;
-			brcm,hardware-controlled;
-			brcm,link-signal-sources = <5>;
-			/* EPHY1 link routed to EPHY2 LED */
-		};
-		ephy3@7 {
-			reg = <7>;
-			brcm,hardware-controlled;
-			brcm,link-signal-sources = <4>;
-			/* EPHY0 link routed to EPHY3 LED */
-		};
-		power_green@20 {
-			reg = <20>;
-			active-low;
-			label = "green:power";
-			default-state = "on";
-		};
-	};
diff --git a/dts/Bindings/leds/leds-bcm6328.yaml b/dts/Bindings/leds/leds-bcm6328.yaml
new file mode 100644
index 0000000000..51cc0d82c1
--- /dev/null
+++ b/dts/Bindings/leds/leds-bcm6328.yaml
@@ -0,0 +1,404 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/leds/leds-bcm6328.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: LEDs connected to Broadcom BCM6328 controller
+
+maintainers:
+  - Álvaro Fernández Rojas <noltari@gmail.com>
+
+description: |
+  This controller is present on BCM6318, BCM6328, BCM6362 and BCM63268.
+  In these SoCs it's possible to control LEDs both as GPIOs or by hardware.
+  However, on some devices there are Serial LEDs (LEDs connected to a 74x164
+  controller), which can either be controlled by software (exporting the 74x164
+  as spi-gpio. See
+  Documentation/devicetree/bindings/gpio/fairchild,74hc595.yaml), or by hardware
+  using this driver.
+  Some of these Serial LEDs are hardware controlled (e.g. ethernet LEDs) and
+  exporting the 74x164 as spi-gpio prevents those LEDs to be hardware
+  controlled, so the only chance to keep them working is by using this driver.
+
+  BCM6328 LED controller has a HWDIS register, which controls whether a LED
+  should be controlled by a hardware signal instead of the MODE register value,
+  with 0 meaning hardware control enabled and 1 hardware control disabled. This
+  is usually 1:1 for hardware to LED signals, but through the activity/link
+  registers you have some limited control over rerouting the LEDs (as
+  explained later in brcm,link-signal-sources). Even if a LED is hardware
+  controlled you are still able to make it blink or light it up if it isn't,
+  but you can't turn it off if the hardware decides to light it up. For this
+  reason, hardware controlled LEDs aren't registered as LED class devices.
+
+  Each LED is represented as a sub-node of the brcm,bcm6328-leds device.
+
+properties:
+  compatible:
+    const: brcm,bcm6328-leds
+
+  reg:
+    maxItems: 1
+
+  brcm,serial-leds:
+    type: boolean
+    description: Enables Serial LEDs.
+
+  brcm,serial-mux:
+    type: boolean
+    description: Enables Serial LEDs multiplexing.
+
+  brcm,serial-clk-low:
+    type: boolean
+    description: Makes clock signal active low.
+
+  brcm,serial-dat-low:
+    type: boolean
+    description: Makes data signal active low.
+
+  brcm,serial-shift-inv:
+    type: boolean
+    description: Inverts Serial LEDs shift direction.
+
+  "#address-cells":
+    const: 1
+
+  "#size-cells":
+    const: 0
+
+patternProperties:
+  "@[a-f0-9]+$":
+    type: object
+
+    $ref: common.yaml#
+
+    properties:
+      reg:
+        items:
+          - maximum: 23
+        description: LED pin number (only LEDs 0 to 23 are valid).
+
+      active-low:
+        type: boolean
+        description: Makes LED active low.
+
+      brcm,hardware-controlled:
+        type: boolean
+        description: Makes this LED hardware controlled.
+
+      brcm,link-signal-sources:
+        $ref: /schemas/types.yaml#/definitions/uint32-array
+        minItems: 1
+        maxItems: 4
+        description: >
+          An array of hardware link signal sources. Up to four link hardware
+          signals can get muxed into these LEDs. Only valid for LEDs 0 to 7,
+          where LED signals 0 to 3 may be muxed to LEDs 0 to 3, and signals 4 to
+          7 may be muxed to LEDs 4 to 7. A signal can be muxed to more than one
+          LED, and one LED can have more than one source signal.
+
+      brcm,activity-signal-sources:
+        $ref: /schemas/types.yaml#/definitions/uint32-array
+        minItems: 1
+        maxItems: 4
+        description: >
+          An array of hardware activity signal sources. Up to four activity
+          hardware signals can get muxed into these LEDs. Only valid for LEDs 0
+          to 7, where LED signals 0 to 3 may be muxed to LEDs 0 to 3, and
+          signals 4 to 7 may be muxed to LEDs 4 to 7. A signal can be muxed to
+          more than one LED, and one LED can have more than one source signal.
+
+    required:
+      - reg
+
+    unevaluatedProperties: false
+
+required:
+  - reg
+  - "#address-cells"
+  - "#size-cells"
+
+additionalProperties: false
+
+examples:
+  - |
+    /* BCM6328 with 4 EPHY LEDs */
+    led-controller@10000800 {
+        compatible = "brcm,bcm6328-leds";
+        #address-cells = <1>;
+        #size-cells = <0>;
+        reg = <0x10000800 0x24>;
+
+        alarm_red@2 {
+            reg = <2>;
+            active-low;
+            label = "red:alarm";
+        };
+
+        inet_green@3 {
+            reg = <3>;
+            active-low;
+            label = "green:inet";
+        };
+
+        power_green@4 {
+            reg = <4>;
+            active-low;
+            label = "green:power";
+            default-state = "on";
+        };
+
+        ephy0_spd@17 {
+            reg = <17>;
+            brcm,hardware-controlled;
+        };
+
+        ephy1_spd@18 {
+            reg = <18>;
+            brcm,hardware-controlled;
+        };
+
+        ephy2_spd@19 {
+            reg = <19>;
+            brcm,hardware-controlled;
+        };
+
+        ephy3_spd@20 {
+            reg = <20>;
+            brcm,hardware-controlled;
+        };
+    };
+  - |
+    /* BCM63268 with Serial/GPHY0 LEDs */
+    led-controller@10001900 {
+        compatible = "brcm,bcm6328-leds";
+        #address-cells = <1>;
+        #size-cells = <0>;
+        reg = <0x10001900 0x24>;
+        brcm,serial-leds;
+        brcm,serial-dat-low;
+        brcm,serial-shift-inv;
+
+        gphy0_spd0@0 {
+            reg = <0>;
+            brcm,hardware-controlled;
+            brcm,link-signal-sources = <0>;
+        };
+
+        gphy0_spd1@1 {
+            reg = <1>;
+            brcm,hardware-controlled;
+            brcm,link-signal-sources = <1>;
+        };
+
+        inet_red@2 {
+            reg = <2>;
+            active-low;
+            label = "red:inet";
+        };
+
+        dsl_green@3 {
+            reg = <3>;
+            active-low;
+            label = "green:dsl";
+        };
+
+        usb_green@4 {
+            reg = <4>;
+            active-low;
+            label = "green:usb";
+        };
+
+        wps_green@7 {
+            reg = <7>;
+            active-low;
+            label = "green:wps";
+        };
+
+        inet_green@8 {
+            reg = <8>;
+            active-low;
+            label = "green:inet";
+        };
+
+        ephy0_act@9 {
+            reg = <9>;
+            brcm,hardware-controlled;
+        };
+
+        ephy1_act@10 {
+            reg = <10>;
+            brcm,hardware-controlled;
+        };
+
+        ephy2_act@11 {
+            reg = <11>;
+            brcm,hardware-controlled;
+        };
+
+        gphy0_act@12 {
+            reg = <12>;
+            brcm,hardware-controlled;
+        };
+
+        ephy0_spd@13 {
+            reg = <13>;
+            brcm,hardware-controlled;
+        };
+
+        ephy1_spd@14 {
+            reg = <14>;
+            brcm,hardware-controlled;
+        };
+
+        ephy2_spd@15 {
+            reg = <15>;
+            brcm,hardware-controlled;
+        };
+
+        power_green@20 {
+            reg = <20>;
+            active-low;
+            label = "green:power";
+            default-state = "on";
+        };
+    };
+  - |
+    /* BCM6362 with 1 LED for each EPHY */
+    led-controller@10001900 {
+        compatible = "brcm,bcm6328-leds";
+        #address-cells = <1>;
+        #size-cells = <0>;
+        reg = <0x10001900 0x24>;
+
+        usb@0 {
+            reg = <0>;
+            brcm,hardware-controlled;
+            brcm,link-signal-sources = <0>;
+            brcm,activity-signal-sources = <0>;
+            /* USB link/activity routed to USB LED */
+        };
+
+        inet@1 {
+            reg = <1>;
+            brcm,hardware-controlled;
+            brcm,activity-signal-sources = <1>;
+            /* INET activity routed to INET LED */
+        };
+
+        ephy0@4 {
+            reg = <4>;
+            brcm,hardware-controlled;
+            brcm,link-signal-sources = <4>;
+            /* EPHY0 link routed to EPHY0 LED */
+        };
+
+        ephy1@5 {
+            reg = <5>;
+            brcm,hardware-controlled;
+            brcm,link-signal-sources = <5>;
+            /* EPHY1 link routed to EPHY1 LED */
+        };
+
+        ephy2@6 {
+            reg = <6>;
+            brcm,hardware-controlled;
+            brcm,link-signal-sources = <6>;
+            /* EPHY2 link routed to EPHY2 LED */
+        };
+
+        ephy3@7 {
+            reg = <7>;
+            brcm,hardware-controlled;
+            brcm,link-signal-sources = <7>;
+            /* EPHY3 link routed to EPHY3 LED */
+        };
+
+        power_green@20 {
+            reg = <20>;
+            active-low;
+            label = "green:power";
+            default-state = "on";
+        };
+    };
+  - |
+    /* BCM6362 with 1 LED for all EPHYs */
+    led-controller@10001900 {
+        compatible = "brcm,bcm6328-leds";
+        #address-cells = <1>;
+        #size-cells = <0>;
+        reg = <0x10001900 0x24>;
+
+        usb@0 {
+            reg = <0>;
+            brcm,hardware-controlled;
+            brcm,link-signal-sources = <0 1>;
+            brcm,activity-signal-sources = <0 1>;
+            /* USB/INET link/activity routed to USB LED */
+        };
+
+        ephy@4 {
+            reg = <4>;
+            brcm,hardware-controlled;
+            brcm,link-signal-sources = <4 5 6 7>;
+            /* EPHY0/1/2/3 link routed to EPHY0 LED */
+        };
+
+        power_green@20 {
+            reg = <20>;
+            active-low;
+            label = "green:power";
+            default-state = "on";
+        };
+    };
+  - |
+    /* BCM6362 with EPHY LEDs swapped */
+    led-controller@10001900 {
+        compatible = "brcm,bcm6328-leds";
+        #address-cells = <1>;
+        #size-cells = <0>;
+        reg = <0x10001900 0x24>;
+
+        usb@0 {
+            reg = <0>;
+            brcm,hardware-controlled;
+            brcm,link-signal-sources = <0>;
+            brcm,activity-signal-sources = <0 1>;
+            /* USB link/act and INET act routed to USB LED */
+        };
+
+        ephy0@4 {
+            reg = <4>;
+            brcm,hardware-controlled;
+            brcm,link-signal-sources = <7>;
+            /* EPHY3 link routed to EPHY0 LED */
+        };
+
+        ephy1@5 {
+            reg = <5>;
+            brcm,hardware-controlled;
+            brcm,link-signal-sources = <6>;
+            /* EPHY2 link routed to EPHY1 LED */
+        };
+
+        ephy2@6 {
+            reg = <6>;
+            brcm,hardware-controlled;
+            brcm,link-signal-sources = <5>;
+            /* EPHY1 link routed to EPHY2 LED */
+        };
+
+        ephy3@7 {
+            reg = <7>;
+            brcm,hardware-controlled;
+            brcm,link-signal-sources = <4>;
+            /* EPHY0 link routed to EPHY3 LED */
+        };
+
+        power_green@20 {
+            reg = <20>;
+            active-low;
+            label = "green:power";
+            default-state = "on";
+        };
+    };
diff --git a/dts/Bindings/leds/leds-mt6360.yaml b/dts/Bindings/leds/leds-mt6360.yaml
new file mode 100644
index 0000000000..b2fe6eb893
--- /dev/null
+++ b/dts/Bindings/leds/leds-mt6360.yaml
@@ -0,0 +1,159 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/leds/leds-mt6360.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: LED driver for MT6360 PMIC from MediaTek Integrated.
+
+maintainers:
+  - Gene Chen <gene_chen@richtek.com>
+
+description: |
+  This module is part of the MT6360 MFD device.
+  see Documentation/devicetree/bindings/mfd/mt6360.yaml
+  Add MT6360 LED driver include 2-channel Flash LED with torch/strobe mode,
+  and 4-channel RGB LED support Register/Flash/Breath Mode
+
+properties:
+  compatible:
+    const: mediatek,mt6360-led
+
+  "#address-cells":
+    const: 1
+
+  "#size-cells":
+    const: 0
+
+patternProperties:
+  "^(multi-)?led@[0-5]$":
+    type: object
+    $ref: common.yaml#
+    description:
+      Properties for a single LED.
+
+    properties:
+      reg:
+        description: Index of the LED.
+        enum:
+          - 0 # LED output ISINK1
+          - 1 # LED output ISINK2
+          - 2 # LED output ISINK3
+          - 3 # LED output ISINKML
+          - 4 # LED output FLASH1
+          - 5 # LED output FLASH2
+
+unevaluatedProperties: false
+
+required:
+  - compatible
+  - "#address-cells"
+  - "#size-cells"
+
+additionalProperties: false
+
+examples:
+  - |
+   #include <dt-bindings/leds/common.h>
+   led-controller {
+     compatible = "mediatek,mt6360-led";
+     #address-cells = <1>;
+     #size-cells = <0>;
+
+     multi-led@0 {
+       reg = <0>;
+       function = LED_FUNCTION_INDICATOR;
+       color = <LED_COLOR_ID_RGB>;
+       led-max-microamp = <24000>;
+       #address-cells = <1>;
+       #size-cells = <0>;
+       led@0 {
+         reg = <0>;
+         color = <LED_COLOR_ID_RED>;
+       };
+       led@1 {
+         reg = <1>;
+         color = <LED_COLOR_ID_GREEN>;
+       };
+       led@2 {
+         reg = <2>;
+         color = <LED_COLOR_ID_BLUE>;
+       };
+     };
+     led@3 {
+       reg = <3>;
+       function = LED_FUNCTION_INDICATOR;
+       color = <LED_COLOR_ID_WHITE>;
+       led-max-microamp = <150000>;
+     };
+     led@4 {
+       reg = <4>;
+       function = LED_FUNCTION_FLASH;
+       color = <LED_COLOR_ID_WHITE>;
+       function-enumerator = <1>;
+       led-max-microamp = <200000>;
+       flash-max-microamp = <500000>;
+       flash-max-timeout-us = <1024000>;
+     };
+     led@5 {
+       reg = <5>;
+       function = LED_FUNCTION_FLASH;
+       color = <LED_COLOR_ID_WHITE>;
+       function-enumerator = <2>;
+       led-max-microamp = <200000>;
+       flash-max-microamp = <500000>;
+       flash-max-timeout-us = <1024000>;
+     };
+   };
+
+  - |
+
+   led-controller {
+     compatible = "mediatek,mt6360-led";
+     #address-cells = <1>;
+     #size-cells = <0>;
+
+     led@0 {
+       reg = <0>;
+       function = LED_FUNCTION_INDICATOR;
+       color = <LED_COLOR_ID_RED>;
+       led-max-microamp = <24000>;
+     };
+     led@1 {
+       reg = <1>;
+       function = LED_FUNCTION_INDICATOR;
+       color = <LED_COLOR_ID_GREEN>;
+       led-max-microamp = <24000>;
+     };
+     led@2 {
+       reg = <2>;
+       function = LED_FUNCTION_INDICATOR;
+       color = <LED_COLOR_ID_BLUE>;
+       led-max-microamp = <24000>;
+     };
+     led@3 {
+       reg = <3>;
+       function = LED_FUNCTION_INDICATOR;
+       color = <LED_COLOR_ID_WHITE>;
+       led-max-microamp = <150000>;
+     };
+     led@4 {
+       reg = <4>;
+       function = LED_FUNCTION_FLASH;
+       color = <LED_COLOR_ID_WHITE>;
+       function-enumerator = <1>;
+       led-max-microamp = <200000>;
+       flash-max-microamp = <500000>;
+       flash-max-timeout-us = <1024000>;
+     };
+     led@5 {
+       reg = <5>;
+       function = LED_FUNCTION_FLASH;
+       color = <LED_COLOR_ID_WHITE>;
+       function-enumerator = <2>;
+       led-max-microamp = <200000>;
+       flash-max-microamp = <500000>;
+       flash-max-timeout-us = <1024000>;
+     };
+   };
+...