dts: update to v4.19-rc1

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

7 files changed, 118 insertions, 1 deletions

diff --git a/dts/Bindings/media/i2c/ak7375.txt b/dts/Bindings/media/i2c/ak7375.txt
new file mode 100644
index 0000000000..aa3e24b412
--- /dev/null
+++ b/dts/Bindings/media/i2c/ak7375.txt
@@ -0,0 +1,8 @@
+Asahi Kasei Microdevices AK7375 voice coil lens driver
+
+AK7375 is a camera voice coil lens.
+
+Mandatory properties:
+
+- compatible: "asahi-kasei,ak7375"
+- reg: I2C slave address
diff --git a/dts/Bindings/media/i2c/aptina,mt9v111.txt b/dts/Bindings/media/i2c/aptina,mt9v111.txt
new file mode 100644
index 0000000000..bd896e9f67
--- /dev/null
+++ b/dts/Bindings/media/i2c/aptina,mt9v111.txt
@@ -0,0 +1,46 @@
+* Aptina MT9V111 CMOS sensor
+----------------------------
+
+The Aptina MT9V111 is a 1/4-Inch VGA-format digital image sensor with a core
+based on Aptina MT9V011 sensor and an integrated Image Flow Processor (IFP).
+
+The sensor has an active pixel array of 640x480 pixels and can output a number
+of image resolution and formats controllable through a simple two-wires
+interface.
+
+Required properties:
+--------------------
+
+- compatible: shall be "aptina,mt9v111".
+- clocks: reference to the system clock input provider.
+
+Optional properties:
+--------------------
+
+- enable-gpios: output enable signal, pin name "OE#". Active low.
+- standby-gpios: low power state control signal, pin name "STANDBY".
+  Active high.
+- reset-gpios: chip reset signal, pin name "RESET#". Active low.
+
+The device node must contain one 'port' child node with one 'endpoint' child
+sub-node for its digital output video port, in accordance with the video
+interface bindings defined in:
+Documentation/devicetree/bindings/media/video-interfaces.txt
+
+Example:
+--------
+
+        &i2c1 {
+                camera@48 {
+                        compatible = "aptina,mt9v111";
+                        reg = <0x48>;
+
+                        clocks = <&camera_clk>;
+
+                        port {
+                                mt9v111_out: endpoint {
+                                        remote-endpoint = <&ceu_in>;
+                                };
+                        };
+                };
+        };
diff --git a/dts/Bindings/media/i2c/dongwoon,dw9807.txt b/dts/Bindings/media/i2c/dongwoon,dw9807.txt
new file mode 100644
index 0000000000..c4701f1eaa
--- /dev/null
+++ b/dts/Bindings/media/i2c/dongwoon,dw9807.txt
@@ -0,0 +1,9 @@
+Dongwoon Anatech DW9807 voice coil lens driver
+
+DW9807 is a 10-bit DAC with current sink capability. It is intended for
+controlling voice coil lenses.
+
+Mandatory properties:
+
+- compatible: "dongwoon,dw9807-vcm"
+- reg: I2C slave address
diff --git a/dts/Bindings/media/i2c/nokia,smia.txt b/dts/Bindings/media/i2c/nokia,smia.txt
index 33f10a94c3..8ee7c7972a 100644
--- a/dts/Bindings/media/i2c/nokia,smia.txt
+++ b/dts/Bindings/media/i2c/nokia,smia.txt
@@ -29,6 +29,9 @@ Optional properties
 - reset-gpios: XSHUTDOWN GPIO
 - flash-leds: See ../video-interfaces.txt
 - lens-focus: See ../video-interfaces.txt
+- rotation: Integer property; valid values are 0 (sensor mounted upright)
+	    and 180 (sensor mounted upside down). See
+	    ../video-interfaces.txt .
 
 
 Endpoint node mandatory properties
diff --git a/dts/Bindings/media/i2c/ov2680.txt b/dts/Bindings/media/i2c/ov2680.txt
new file mode 100644
index 0000000000..11e925ed9d
--- /dev/null
+++ b/dts/Bindings/media/i2c/ov2680.txt
@@ -0,0 +1,46 @@
+* Omnivision OV2680 MIPI CSI-2 sensor
+
+Required Properties:
+- compatible: should be "ovti,ov2680".
+- clocks: reference to the xvclk input clock.
+- clock-names: should be "xvclk".
+- DOVDD-supply: Digital I/O voltage supply.
+- DVDD-supply: Digital core voltage supply.
+- AVDD-supply: Analog voltage supply.
+
+Optional Properties:
+- reset-gpios: reference to the GPIO connected to the powerdown/reset pin,
+               if any. This is an active low signal to the OV2680.
+
+The device node must contain one 'port' child node for its digital output
+video port, and this port must have a single endpoint in accordance with
+ the video interface bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Endpoint node required properties for CSI-2 connection are:
+- remote-endpoint: a phandle to the bus receiver's endpoint node.
+- clock-lanes: should be set to <0> (clock lane on hardware lane 0).
+- data-lanes: should be set to <1> (one CSI-2 lane supported).
+
+Example:
+
+&i2c2 {
+	ov2680: camera-sensor@36 {
+		compatible = "ovti,ov2680";
+		reg = <0x36>;
+		clocks = <&osc>;
+		clock-names = "xvclk";
+		reset-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
+		DOVDD-supply = <&sw2_reg>;
+		DVDD-supply = <&sw2_reg>;
+		AVDD-supply = <&reg_peri_3p15v>;
+
+		port {
+			ov2680_to_mipi: endpoint {
+				remote-endpoint = <&mipi_from_sensor>;
+				clock-lanes = <0>;
+				data-lanes = <1>;
+			};
+		};
+	};
+};
diff --git a/dts/Bindings/media/i2c/ov5640.txt b/dts/Bindings/media/i2c/ov5640.txt
index 8e36da0d84..c97c2f2da1 100644
--- a/dts/Bindings/media/i2c/ov5640.txt
+++ b/dts/Bindings/media/i2c/ov5640.txt
@@ -13,6 +13,10 @@ Optional Properties:
 	       This is an active low signal to the OV5640.
 - powerdown-gpios: reference to the GPIO connected to the powerdown pin,
 		   if any. This is an active high signal to the OV5640.
+- rotation: as defined in
+	    Documentation/devicetree/bindings/media/video-interfaces.txt,
+	    valid values are 0 (sensor mounted upright) and 180 (sensor
+	    mounted upside down).
 
 The device node must contain one 'port' child node for its digital output
 video port, in accordance with the video interface bindings defined in
@@ -51,6 +55,7 @@ Examples:
 		DVDD-supply = <&vgen2_reg>;  /* 1.5v */
 		powerdown-gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>;
 		reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
+		rotation = <180>;
 
 		port {
 			/* MIPI CSI-2 bus endpoint */
diff --git a/dts/Bindings/media/i2c/tc358743.txt b/dts/Bindings/media/i2c/tc358743.txt
index 49f8bcc2ea..59102edcf0 100644
--- a/dts/Bindings/media/i2c/tc358743.txt
+++ b/dts/Bindings/media/i2c/tc358743.txt
@@ -12,7 +12,7 @@ Required Properties:
 Optional Properties:
 
 - reset-gpios: gpio phandle GPIO connected to the reset pin
-- interrupts, interrupt-parent: GPIO connected to the interrupt pin
+- interrupts: GPIO connected to the interrupt pin
 - data-lanes: should be <1 2 3 4> for four-lane operation,
 	      or <1 2> for two-lane operation
 - clock-lanes: should be <0>