dts: update to v5.5-rc1

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

4 files changed, 76 insertions, 3 deletions

diff --git a/dts/Bindings/media/i2c/ad5820.txt b/dts/Bindings/media/i2c/ad5820.txt
index 5940ca11c0..5764cbedf9 100644
--- a/dts/Bindings/media/i2c/ad5820.txt
+++ b/dts/Bindings/media/i2c/ad5820.txt
@@ -2,12 +2,20 @@
 
 Required Properties:
 
-  - compatible: Must contain "adi,ad5820"
+  - compatible: Must contain one of:
+		- "adi,ad5820"
+		- "adi,ad5821"
+		- "adi,ad5823"
 
   - reg: I2C slave address
 
   - VANA-supply: supply of voltage for VANA pin
 
+Optional properties:
+
+   - enable-gpios : GPIO spec for the XSHUTDOWN pin. The XSHUTDOWN signal is
+active low, a high level on the pin enables the device.
+
 Example:
 
        ad5820: coil@c {
@@ -15,5 +23,6 @@ Example:
                reg = <0x0c>;
 
                VANA-supply = <&vaux4>;
+               enable-gpios = <&msmgpio 26 GPIO_ACTIVE_HIGH>;
        };
 
diff --git a/dts/Bindings/media/i2c/imx290.txt b/dts/Bindings/media/i2c/imx290.txt
new file mode 100644
index 0000000000..a3cc21410f
--- /dev/null
+++ b/dts/Bindings/media/i2c/imx290.txt
@@ -0,0 +1,57 @@
+* Sony IMX290 1/2.8-Inch CMOS Image Sensor
+
+The Sony IMX290 is a 1/2.8-Inch CMOS Solid-state image sensor with
+Square Pixel for Color Cameras. It is programmable through I2C and 4-wire
+interfaces. The sensor output is available via CMOS logic parallel SDR output,
+Low voltage LVDS DDR output and CSI-2 serial data output. The CSI-2 bus is the
+default. No bindings have been defined for the other busses.
+
+Required Properties:
+- compatible: Should be "sony,imx290"
+- reg: I2C bus address of the device
+- clocks: Reference to the xclk clock.
+- clock-names: Should be "xclk".
+- clock-frequency: Frequency of the xclk clock in Hz.
+- vdddo-supply: Sensor digital IO regulator.
+- vdda-supply: Sensor analog regulator.
+- vddd-supply: Sensor digital core regulator.
+
+Optional Properties:
+- reset-gpios: Sensor reset GPIO
+
+The imx290 device node should contain one 'port' child node with
+an 'endpoint' subnode. For further reading on port node refer to
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Required Properties on endpoint:
+- data-lanes: check ../video-interfaces.txt
+- link-frequencies: check ../video-interfaces.txt
+- remote-endpoint: check ../video-interfaces.txt
+
+Example:
+	&i2c1 {
+		...
+		imx290: camera-sensor@1a {
+			compatible = "sony,imx290";
+			reg = <0x1a>;
+
+			reset-gpios = <&msmgpio 35 GPIO_ACTIVE_LOW>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&camera_rear_default>;
+
+			clocks = <&gcc GCC_CAMSS_MCLK0_CLK>;
+			clock-names = "xclk";
+			clock-frequency = <37125000>;
+
+			vdddo-supply = <&camera_vdddo_1v8>;
+			vdda-supply = <&camera_vdda_2v8>;
+			vddd-supply = <&camera_vddd_1v5>;
+
+			port {
+				imx290_ep: endpoint {
+					data-lanes = <1 2 3 4>;
+					link-frequencies = /bits/ 64 <445500000>;
+					remote-endpoint = <&csiphy0_ep>;
+				};
+			};
+		};
diff --git a/dts/Bindings/media/i2c/nokia,smia.txt b/dts/Bindings/media/i2c/nokia,smia.txt
index c3c3479233..10ece81080 100644
--- a/dts/Bindings/media/i2c/nokia,smia.txt
+++ b/dts/Bindings/media/i2c/nokia,smia.txt
@@ -27,8 +27,6 @@ Mandatory properties
 Optional properties
 -------------------
 
-- nokia,nvm-size: The size of the NVM, in bytes. If the size is not given,
-  the NVM contents will not be read.
 - reset-gpios: XSHUTDOWN GPIO
 - flash-leds: See ../video-interfaces.txt
 - lens-focus: See ../video-interfaces.txt
diff --git a/dts/Bindings/media/i2c/ov2659.txt b/dts/Bindings/media/i2c/ov2659.txt
index cabc7d827d..92989a619f 100644
--- a/dts/Bindings/media/i2c/ov2659.txt
+++ b/dts/Bindings/media/i2c/ov2659.txt
@@ -12,6 +12,12 @@ Required Properties:
 - clock-names: should be "xvclk".
 - link-frequencies: target pixel clock frequency.
 
+Optional Properties:
+- powerdown-gpios: reference to the GPIO connected to the pwdn pin, if any.
+  Active high with internal pull down resistor.
+- reset-gpios: reference to the GPIO connected to the resetb pin, if any.
+  Active low with internal pull up resistor.
+
 For further reading on port node refer to
 Documentation/devicetree/bindings/media/video-interfaces.txt.
 
@@ -27,6 +33,9 @@ Example:
 			clocks = <&clk_ov2659 0>;
 			clock-names = "xvclk";
 
+			powerdown-gpios = <&gpio6 14 GPIO_ACTIVE_HIGH>;
+			reset-gpios = <&gpio6 15 GPIO_ACTIVE_LOW>;
+
 			port {
 				ov2659_0: endpoint {
 					remote-endpoint = <&vpfe_ep>;