dts: update to v4.13-rc2

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>

3 files changed, 119 insertions, 0 deletions

diff --git a/dts/Bindings/media/i2c/adv7180.txt b/dts/Bindings/media/i2c/adv7180.txt
index 4da486f96f..552b6a82cb 100644
--- a/dts/Bindings/media/i2c/adv7180.txt
+++ b/dts/Bindings/media/i2c/adv7180.txt
@@ -6,6 +6,8 @@ digital interfaces like MIPI CSI-2 or parallel video.
 Required Properties :
 - compatible : value must be one of
 		"adi,adv7180"
+		"adi,adv7180cp"
+		"adi,adv7180st"
 		"adi,adv7182"
 		"adi,adv7280"
 		"adi,adv7280-m"
@@ -15,6 +17,19 @@ Required Properties :
 		"adi,adv7282"
 		"adi,adv7282-m"
 
+Device nodes of "adi,adv7180cp" and "adi,adv7180st" must contain one
+'port' child node per device input and output port, in accordance with the
+video interface bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt. The port
+nodes are numbered as follows.
+
+  Port		adv7180cp	adv7180st
+-------------------------------------------------------------------
+  Input		0-2		0-5
+  Output	3		6
+
+The digital output port node must contain at least one endpoint.
+
 Optional Properties :
 - powerdown-gpios: reference to the GPIO connected to the powerdown pin,
   if any.
diff --git a/dts/Bindings/media/i2c/max2175.txt b/dts/Bindings/media/i2c/max2175.txt
new file mode 100644
index 0000000000..02b4e9cd7b
--- /dev/null
+++ b/dts/Bindings/media/i2c/max2175.txt
@@ -0,0 +1,59 @@
+Maxim Integrated MAX2175 RF to Bits tuner
+-----------------------------------------
+
+The MAX2175 IC is an advanced analog/digital hybrid-radio receiver with
+RF to Bits® front-end designed for software-defined radio solutions.
+
+Required properties:
+--------------------
+- compatible: "maxim,max2175" for MAX2175 RF-to-bits tuner.
+- clocks: clock specifier.
+- port: child port node corresponding to the I2S output, in accordance with
+	the video interface bindings defined in
+	Documentation/devicetree/bindings/media/video-interfaces.txt. The port
+	node must contain at least one endpoint.
+
+Optional properties:
+--------------------
+- maxim,master	      : phandle to the master tuner if it is a slave. This
+			is used to define two tuners in diversity mode
+			(1 master, 1 slave). By default each tuner is an
+			individual master.
+- maxim,refout-load   : load capacitance value (in picofarads) on reference
+			output drive level. The possible load values are:
+			 0 (default - refout disabled)
+			10
+			20
+			30
+			40
+			60
+			70
+- maxim,am-hiz-filter : empty property indicates the AM Hi-Z filter is used
+			in this hardware for AM antenna input.
+
+Example:
+--------
+
+Board specific DTS file
+
+/* Fixed XTAL clock node */
+maxim_xtal: clock {
+	compatible = "fixed-clock";
+	#clock-cells = <0>;
+	clock-frequency = <36864000>;
+};
+
+/* A tuner device instance under i2c bus */
+max2175_0: tuner@60 {
+	compatible = "maxim,max2175";
+	reg = <0x60>;
+	clocks = <&maxim_xtal>;
+	maxim,refout-load = <10>;
+
+	port {
+		max2175_0_ep: endpoint {
+			remote-endpoint = <&slave_rx_device>;
+		};
+	};
+
+};
diff --git a/dts/Bindings/media/i2c/ov5640.txt b/dts/Bindings/media/i2c/ov5640.txt
new file mode 100644
index 0000000000..540b36c4b1
--- /dev/null
+++ b/dts/Bindings/media/i2c/ov5640.txt
@@ -0,0 +1,45 @@
+* Omnivision OV5640 MIPI CSI-2 sensor
+
+Required Properties:
+- compatible: should be "ovti,ov5640"
+- clocks: reference to the xclk input clock.
+- clock-names: should be "xclk".
+- DOVDD-supply: Digital I/O voltage supply, 1.8 volts
+- AVDD-supply: Analog voltage supply, 2.8 volts
+- DVDD-supply: Digital core voltage supply, 1.5 volts
+
+Optional Properties:
+- reset-gpios: reference to the GPIO connected to the reset pin, if any.
+	       This is an active low signal to the OV5640.
+- powerdown-gpios: reference to the GPIO connected to the powerdown pin,
+		   if any. This is an active high signal to the OV5640.
+
+The device node must contain one 'port' child node for its digital output
+video port, in accordance with the video interface bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+
+&i2c1 {
+	ov5640: camera@3c {
+		compatible = "ovti,ov5640";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ov5640>;
+		reg = <0x3c>;
+		clocks = <&clks IMX6QDL_CLK_CKO>;
+		clock-names = "xclk";
+		DOVDD-supply = <&vgen4_reg>; /* 1.8v */
+		AVDD-supply = <&vgen3_reg>;  /* 2.8v */
+		DVDD-supply = <&vgen2_reg>;  /* 1.5v */
+		powerdown-gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
+
+		port {
+			ov5640_to_mipi_csi2: endpoint {
+				remote-endpoint = <&mipi_csi2_from_ov5640>;
+				clock-lanes = <0>;
+				data-lanes = <1 2>;
+			};
+		};
+	};
+};