dts: update to v3.17-rc1

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

6 files changed, 239 insertions, 4 deletions

diff --git a/dts/Bindings/media/atmel-isi.txt b/dts/Bindings/media/atmel-isi.txt
new file mode 100644
index 0000000000..17e71b7b44
--- /dev/null
+++ b/dts/Bindings/media/atmel-isi.txt
@@ -0,0 +1,51 @@
+Atmel Image Sensor Interface (ISI) SoC Camera Subsystem
+----------------------------------------------
+
+Required properties:
+- compatible: must be "atmel,at91sam9g45-isi"
+- reg: physical base address and length of the registers set for the device;
+- interrupts: should contain IRQ line for the ISI;
+- clocks: list of clock specifiers, corresponding to entries in
+          the clock-names property;
+- clock-names: must contain "isi_clk", which is the isi peripherial clock.
+
+ISI supports a single port node with parallel bus. It should contain one
+'port' child node with child 'endpoint' node. Please refer to the bindings
+defined in Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+	isi: isi@f0034000 {
+		compatible = "atmel,at91sam9g45-isi";
+		reg = <0xf0034000 0x4000>;
+		interrupts = <37 IRQ_TYPE_LEVEL_HIGH 5>;
+
+		clocks = <&isi_clk>;
+		clock-names = "isi_clk";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_isi>;
+
+		port {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			isi_0: endpoint {
+				remote-endpoint = <&ov2640_0>;
+				bus-width = <8>;
+			};
+		};
+	};
+
+	i2c1: i2c@f0018000 {
+		ov2640: camera@0x30 {
+			compatible = "omnivision,ov2640";
+			reg = <0x30>;
+
+			port {
+				ov2640_0: endpoint {
+					remote-endpoint = <&isi_0>;
+					bus-width = <8>;
+				};
+			};
+		};
+	};
diff --git a/dts/Bindings/media/exynos-jpeg-codec.txt b/dts/Bindings/media/exynos-jpeg-codec.txt
index 937b755baf..bf52ed4a50 100644
--- a/dts/Bindings/media/exynos-jpeg-codec.txt
+++ b/dts/Bindings/media/exynos-jpeg-codec.txt
@@ -3,9 +3,13 @@ Samsung S5P/EXYNOS SoC series JPEG codec
 Required properties:
 
 - compatible	: should be one of:
-		  "samsung,s5pv210-jpeg", "samsung,exynos4210-jpeg";
+		  "samsung,s5pv210-jpeg", "samsung,exynos4210-jpeg",
+		  "samsung,exynos3250-jpeg";
 - reg		: address and length of the JPEG codec IP register set;
 - interrupts	: specifies the JPEG codec IP interrupt;
-- clocks	: should contain the JPEG codec IP gate clock specifier, from the
-		  common clock bindings;
-- clock-names	: should contain "jpeg" entry.
+- clock-names   : should contain:
+		   - "jpeg" for the core gate clock,
+		   - "sclk" for the special clock (optional).
+- clocks	: should contain the clock specifier and clock ID list
+		  matching entries in the clock-names property; from
+		  the common clock bindings.
diff --git a/dts/Bindings/media/i2c/mt9m111.txt b/dts/Bindings/media/i2c/mt9m111.txt
new file mode 100644
index 0000000000..ed5a334b1e
--- /dev/null
+++ b/dts/Bindings/media/i2c/mt9m111.txt
@@ -0,0 +1,28 @@
+Micron 1.3Mp CMOS Digital Image Sensor
+
+The Micron MT9M111 is a CMOS active pixel digital image sensor with an active
+array size of 1280H x 1024V. It is programmable through a simple two-wire serial
+interface.
+
+Required Properties:
+- compatible: value should be "micron,mt9m111"
+
+For further reading on port node refer to
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+
+	i2c_master {
+		mt9m111@5d {
+			compatible = "micron,mt9m111";
+			reg = <0x5d>;
+
+			remote = <&pxa_camera>;
+			port {
+				mt9m111_1: endpoint {
+					bus-width = <8>;
+					remote-endpoint = <&pxa_camera>;
+				};
+			};
+		};
+	};
diff --git a/dts/Bindings/media/pxa-camera.txt b/dts/Bindings/media/pxa-camera.txt
new file mode 100644
index 0000000000..11f5b5d51a
--- /dev/null
+++ b/dts/Bindings/media/pxa-camera.txt
@@ -0,0 +1,43 @@
+Marvell PXA camera host interface
+
+Required properties:
+ - compatible: Should be "marvell,pxa270-qci"
+ - reg: register base and size
+ - interrupts: the interrupt number
+ - any required generic properties defined in video-interfaces.txt
+
+Optional properties:
+ - clocks: input clock (see clock-bindings.txt)
+ - clock-output-names: should contain the name of the clock driving the
+                       sensor master clock MCLK
+ - clock-frequency: host interface is driving MCLK, and MCLK rate is this rate
+
+Example:
+
+	pxa_camera: pxa_camera@50000000 {
+		compatible = "marvell,pxa270-qci";
+		reg = <0x50000000 0x1000>;
+		interrupts = <33>;
+
+		clocks = <&pxa2xx_clks 24>;
+		clock-names = "ciclk";
+		clock-frequency = <50000000>;
+		clock-output-names = "qci_mclk";
+
+		status = "okay";
+
+		port {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			/* Parallel bus endpoint */
+			qci: endpoint@0 {
+				reg = <0>;		/* Local endpoint # */
+				remote-endpoint = <&mt9m111_1>;
+				bus-width = <8>;	/* Used data lines */
+				hsync-active = <0>;	/* Active low */
+				vsync-active = <0>;	/* Active low */
+				pclk-sample = <1>;	/* Rising */
+			};
+		};
+	};
diff --git a/dts/Bindings/media/rcar_vin.txt b/dts/Bindings/media/rcar_vin.txt
new file mode 100644
index 0000000000..ba61782c2a
--- /dev/null
+++ b/dts/Bindings/media/rcar_vin.txt
@@ -0,0 +1,86 @@
+Renesas RCar Video Input driver (rcar_vin)
+------------------------------------------
+
+The rcar_vin device provides video input capabilities for the Renesas R-Car
+family of devices. The current blocks are always slaves and suppot one input
+channel which can be either RGB, YUYV or BT656.
+
+ - compatible: Must be one of the following
+   - "renesas,vin-r8a7791" for the R8A7791 device
+   - "renesas,vin-r8a7790" for the R8A7790 device
+   - "renesas,vin-r8a7779" for the R8A7779 device
+   - "renesas,vin-r8a7778" for the R8A7778 device
+ - reg: the register base and size for the device registers
+ - interrupts: the interrupt for the device
+ - clocks: Reference to the parent clock
+
+Additionally, an alias named vinX will need to be created to specify
+which video input device this is.
+
+The per-board settings:
+ - port sub-node describing a single endpoint connected to the vin
+   as described in video-interfaces.txt[1]. Only the first one will
+   be considered as each vin interface has one input port.
+
+   These settings are used to work out video input format and widths
+   into the system.
+
+
+Device node example
+-------------------
+
+	aliases {
+	       vin0 = &vin0;
+	};
+
+        vin0: vin@0xe6ef0000 {
+                compatible = "renesas,vin-r8a7790";
+                clocks = <&mstp8_clks R8A7790_CLK_VIN0>;
+                reg = <0 0xe6ef0000 0 0x1000>;
+                interrupts = <0 188 IRQ_TYPE_LEVEL_HIGH>;
+                status = "disabled";
+        };
+
+Board setup example (vin1 composite video input)
+------------------------------------------------
+
+&i2c2   {
+        status = "ok";
+        pinctrl-0 = <&i2c2_pins>;
+        pinctrl-names = "default";
+
+        adv7180@20 {
+                compatible = "adi,adv7180";
+                reg = <0x20>;
+                remote = <&vin1>;
+
+                port {
+                        adv7180: endpoint {
+                                bus-width = <8>;
+                                remote-endpoint = <&vin1ep0>;
+                        };
+                };
+        };
+};
+
+/* composite video input */
+&vin1 {
+        pinctrl-0 = <&vin1_pins>;
+        pinctrl-names = "default";
+
+        status = "ok";
+
+        port {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                vin1ep0: endpoint {
+                        remote-endpoint = <&adv7180>;
+                        bus-width = <8>;
+                };
+        };
+};
+
+
+
+[1] video-interfaces.txt common video media interface
diff --git a/dts/Bindings/media/sunxi-ir.txt b/dts/Bindings/media/sunxi-ir.txt
new file mode 100644
index 0000000000..23dd5ad07b
--- /dev/null
+++ b/dts/Bindings/media/sunxi-ir.txt
@@ -0,0 +1,23 @@
+Device-Tree bindings for SUNXI IR controller found in sunXi SoC family
+
+Required properties:
+- compatible	    : should be "allwinner,sun4i-a10-ir";
+- clocks	    : list of clock specifiers, corresponding to
+		      entries in clock-names property;
+- clock-names	    : should contain "apb" and "ir" entries;
+- interrupts	    : should contain IR IRQ number;
+- reg		    : should contain IO map address for IR.
+
+Optional properties:
+- linux,rc-map-name : Remote control map name.
+
+Example:
+
+ir0: ir@01c21800 {
+	compatible = "allwinner,sun4i-a10-ir";
+	clocks = <&apb0_gates 6>, <&ir0_clk>;
+	clock-names = "apb", "ir";
+	interrupts = <0 5 1>;
+	reg = <0x01C21800 0x40>;
+	linux,rc-map-name = "rc-rc6-mce";
+};