dts: update to v4.5-rc1

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

1 files changed, 88 insertions, 0 deletions

diff --git a/dts/Bindings/mfd/samsung,sec-core.txt b/dts/Bindings/mfd/samsung,sec-core.txt
new file mode 100644
index 0000000000..cdd079bfc2
--- /dev/null
+++ b/dts/Bindings/mfd/samsung,sec-core.txt
@@ -0,0 +1,88 @@
+Binding for Samsung S2M and S5M family multi-function device
+============================================================
+
+This is a part of device tree bindings for S2M and S5M family multi-function
+devices.
+
+The Samsung S2MPA01, S2MPS11/13/14/15, S2MPU02 and S5M8767 is a family
+of multi-function devices which include voltage and current regulators, RTC,
+charger controller, clock outputs and other sub-blocks. It is interfaced
+to the host controller using an I2C interface. Each sub-block is usually
+addressed by the host system using different I2C slave addresses.
+
+
+This document describes bindings for main device node. Optional sub-blocks
+must be a sub-nodes to it. Bindings for them can be found in:
+ - bindings/regulator/samsung,s2mpa01.txt
+ - bindings/regulator/samsung,s2mps11.txt
+ - bindings/regulator/samsung,s5m8767.txt
+ - bindings/clock/samsung,s2mps11.txt
+
+
+Required properties:
+ - compatible: Should be one of the following
+	- "samsung,s2mpa01-pmic",
+	- "samsung,s2mps11-pmic",
+	- "samsung,s2mps13-pmic",
+	- "samsung,s2mps14-pmic",
+	- "samsung,s2mps15-pmic",
+	- "samsung,s2mpu02-pmic",
+	- "samsung,s5m8767-pmic".
+ - reg: Specifies the I2C slave address of the pmic block. It should be 0x66.
+
+Optional properties:
+ - interrupt-parent: Specifies the phandle of the interrupt controller to which
+   the interrupts from s2mps11 are delivered to.
+ - interrupts: Interrupt specifiers for interrupt sources.
+ - samsung,s2mps11-wrstbi-ground: Indicates that WRSTBI pin of PMIC is pulled
+   down. When the system is suspended it will always go down thus triggerring
+   unwanted buck warm reset (setting buck voltages to default values).
+ - samsung,s2mps11-acokb-ground: Indicates that ACOKB pin of S2MPS11 PMIC is
+   connected to the ground so the PMIC must manually set PWRHOLD bit in CTRL1
+   register to turn off the power. Usually the ACOKB is pulled up to VBATT so
+   when PWRHOLD pin goes low, the rising ACOKB will trigger power off.
+
+Example:
+
+	s2mps11_pmic@66 {
+		compatible = "samsung,s2mps11-pmic";
+		reg = <0x66>;
+
+		s2m_osc: clocks {
+			compatible = "samsung,s2mps11-clk";
+			#clock-cells = <1>;
+			clock-output-names = "xx", "yy", "zz";
+		};
+
+		regulators {
+			ldo1_reg: LDO1 {
+				regulator-name = "VDD_ABB_3.3V";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			ldo2_reg: LDO2 {
+				regulator-name = "VDD_ALIVE_1.1V";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-always-on;
+			};
+
+			buck1_reg: BUCK1 {
+				regulator-name = "vdd_mif";
+				regulator-min-microvolt = <950000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			buck2_reg: BUCK2 {
+				regulator-name = "vdd_arm";
+				regulator-min-microvolt = <950000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-ramp-delay = <50000>;
+			};
+		};
+	};