dts: update to v4.8-rc1

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

4 files changed, 30 insertions, 21 deletions

diff --git a/dts/Bindings/mfd/axp20x.txt b/dts/Bindings/mfd/axp20x.txt
index d20b1034e9..585a955462 100644
--- a/dts/Bindings/mfd/axp20x.txt
+++ b/dts/Bindings/mfd/axp20x.txt
@@ -22,6 +22,11 @@ Optional properties:
 		      AXP152/20X: range:  750-1875, Default: 1.5 MHz
 		      AXP22X/80X: range: 1800-4050, Default: 3   MHz
 
+- x-powers,drive-vbus-en: axp221 / axp223 only boolean, set this when the
+		  N_VBUSEN pin is used as an output pin to control an external
+		  regulator to drive the OTG VBus, rather then as an input pin
+		  which signals whether the board is driving OTG VBus or not.
+
 - <input>-supply: a phandle to the regulator supply node. May be omitted if
 		  inputs are unregulated, such as using the IPSOUT output
 		  from the PMIC.
@@ -79,6 +84,7 @@ ELDO3		: LDO		: eldoin-supply		: shared supply
 LDO_IO0		: LDO		: ips-supply		: GPIO 0
 LDO_IO1		: LDO		: ips-supply		: GPIO 1
 RTC_LDO		: LDO		: ips-supply		: always on
+DRIVEVBUS	: Enable output	: drivevbus-supply	: external regulator
 
 AXP809 regulators, type, and corresponding input supply names:
 
diff --git a/dts/Bindings/mfd/da9052-i2c.txt b/dts/Bindings/mfd/da9052-i2c.txt
index 1857f4a6b9..9554292dc6 100644
--- a/dts/Bindings/mfd/da9052-i2c.txt
+++ b/dts/Bindings/mfd/da9052-i2c.txt
@@ -8,10 +8,13 @@ Sub-nodes:
 - regulators : Contain the regulator nodes. The DA9052/53 regulators are
   bound using their names as listed below:
 
-    buck0     : regulator BUCK0
-    buck1     : regulator BUCK1
-    buck2     : regulator BUCK2
-    buck3     : regulator BUCK3
+    buck1     : regulator BUCK CORE
+    buck2     : regulator BUCK PRO
+    buck3     : regulator BUCK MEM
+    buck4     : regulator BUCK PERI
+    ldo1      : regulator LDO1
+    ldo2      : regulator LDO2
+    ldo3      : regulator LDO3
     ldo4      : regulator LDO4
     ldo5      : regulator LDO5
     ldo6      : regulator LDO6
@@ -19,9 +22,6 @@ Sub-nodes:
     ldo8      : regulator LDO8
     ldo9      : regulator LDO9
     ldo10     : regulator LDO10
-    ldo11     : regulator LDO11
-    ldo12     : regulator LDO12
-    ldo13     : regulator LDO13
 
   The bindings details of individual regulator device can be found in:
   Documentation/devicetree/bindings/regulator/regulator.txt
@@ -36,22 +36,22 @@ i2c@63fc8000 { /* I2C1 */
 		reg = <0x48>;
 
 		regulators {
-			buck0 {
+			buck1 {
 				regulator-min-microvolt = <500000>;
 				regulator-max-microvolt = <2075000>;
 			};
 
-			buck1 {
+			buck2 {
 				regulator-min-microvolt = <500000>;
 				regulator-max-microvolt = <2075000>;
 			};
 
-			buck2 {
+			buck3 {
 				regulator-min-microvolt = <925000>;
 				regulator-max-microvolt = <2500000>;
 			};
 
-			buck3 {
+			buck4 {
 				regulator-min-microvolt = <925000>;
 				regulator-max-microvolt = <2500000>;
 			};
diff --git a/dts/Bindings/mfd/rn5t618.txt b/dts/Bindings/mfd/rn5t618.txt
index 937785a3ed..9e6770b105 100644
--- a/dts/Bindings/mfd/rn5t618.txt
+++ b/dts/Bindings/mfd/rn5t618.txt
@@ -1,18 +1,21 @@
-* Ricoh RN5T618 PMIC
+* Ricoh RN5T567/RN5T618 PMIC
 
-Ricoh RN5T618 is a power management IC which integrates 3 step-down
-DCDC converters, 7 low-dropout regulators, a Li-ion battery charger,
-fuel gauge, ADC, GPIOs and a watchdog timer. It can be controlled
-through a I2C interface.
+Ricoh RN5T567/RN5T618 is a power management IC family which integrates
+3 to 4 step-down DCDC converters, 7 low-dropout regulators, GPIOs and
+a watchdog timer. The RN5T618 provides additionally a Li-ion battery
+charger, fuel gauge and an ADC. It can be controlled through an I2C
+interface.
 
 Required properties:
- - compatible: should be "ricoh,rn5t618"
+ - compatible: must be one of
+		"ricoh,rn5t567"
+		"ricoh,rn5t618"
  - reg: the I2C slave address of the device
 
 Sub-nodes:
  - regulators: the node is required if the regulator functionality is
-   needed. The valid regulator names are: DCDC1, DCDC2, DCDC3, LDO1,
-   LDO2, LDO3, LDO4, LDO5, LDORTC1 and LDORTC2.
+   needed. The valid regulator names are: DCDC1, DCDC2, DCDC3, DCDC4
+   (RN5T567), LDO1, LDO2, LDO3, LDO4, LDO5, LDORTC1 and LDORTC2.
    The common bindings for each individual regulator can be found in:
    Documentation/devicetree/bindings/regulator/regulator.txt
 
diff --git a/dts/Bindings/mfd/twl6040.txt b/dts/Bindings/mfd/twl6040.txt
index a41157b5d9..e6afdfa354 100644
--- a/dts/Bindings/mfd/twl6040.txt
+++ b/dts/Bindings/mfd/twl6040.txt
@@ -19,8 +19,8 @@ Required properties:
 
 Optional properties, nodes:
 - enable-active-high: To power on the twl6040 during boot.
-- clocks: phandle to the clk32k clock provider
-- clock-names: Must be "clk32k"
+- clocks: phandle to the clk32k and/or to mclk clock provider
+- clock-names: Must be "clk32k" for the 32K clock and "mclk" for the MCLK.
 
 Vibra functionality
 Required properties: