dts: update to v4.0-rc1

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

6 files changed, 265 insertions, 0 deletions

diff --git a/dts/Bindings/mfd/atmel-matrix.txt b/dts/Bindings/mfd/atmel-matrix.txt
new file mode 100644
index 0000000000..e3ef50ca02
--- /dev/null
+++ b/dts/Bindings/mfd/atmel-matrix.txt
@@ -0,0 +1,24 @@
+* Device tree bindings for Atmel Bus Matrix
+
+The Bus Matrix registers are used to configure Atmel SoCs internal bus
+behavior (master/slave priorities, undefined burst length type, ...)
+
+Required properties:
+- compatible:		Should be one of the following
+			"atmel,at91sam9260-matrix", "syscon"
+			"atmel,at91sam9261-matrix", "syscon"
+			"atmel,at91sam9263-matrix", "syscon"
+			"atmel,at91sam9rl-matrix", "syscon"
+			"atmel,at91sam9g45-matrix", "syscon"
+			"atmel,at91sam9n12-matrix", "syscon"
+			"atmel,at91sam9x5-matrix", "syscon"
+			"atmel,sama5d3-matrix", "syscon"
+- reg:			Contains offset/length value of the Bus Matrix
+			memory region.
+
+Example:
+
+matrix: matrix@ffffec00 {
+	compatible = "atmel,sama5d3-matrix", "syscon";
+	reg = <0xffffec00 0x200>;
+};
diff --git a/dts/Bindings/mfd/atmel-smc.txt b/dts/Bindings/mfd/atmel-smc.txt
new file mode 100644
index 0000000000..26eeed3739
--- /dev/null
+++ b/dts/Bindings/mfd/atmel-smc.txt
@@ -0,0 +1,19 @@
+* Device tree bindings for Atmel SMC (Static Memory Controller)
+
+The SMC registers are used to configure Atmel EBI (External Bus Interface)
+to interface with standard memory devices (NAND, NOR, SRAM or specialized
+devices like FPGAs).
+
+Required properties:
+- compatible:		Should be one of the following
+			"atmel,at91sam9260-smc", "syscon"
+			"atmel,sama5d3-smc", "syscon"
+- reg:			Contains offset/length value of the SMC memory
+			region.
+
+Example:
+
+smc: smc@ffffc000 {
+	compatible = "atmel,sama5d3-smc", "syscon";
+	reg = <0xffffc000 0x1000>;
+};
diff --git a/dts/Bindings/mfd/da9063.txt b/dts/Bindings/mfd/da9063.txt
new file mode 100644
index 0000000000..42c6fa6f1c
--- /dev/null
+++ b/dts/Bindings/mfd/da9063.txt
@@ -0,0 +1,93 @@
+* Dialog DA9063 Power Management Integrated Circuit (PMIC)
+
+DA9093 consists of a large and varied group of sub-devices (I2C Only):
+
+Device                   Supply Names    Description
+------                   ------------    -----------
+da9063-regulator        :               : LDOs & BUCKs
+da9063-rtc              :               : Real-Time Clock
+da9063-watchdog         :               : Watchdog
+
+======
+
+Required properties:
+
+- compatible : Should be "dlg,da9063"
+- reg : Specifies the I2C slave address (this defaults to 0x58 but it can be
+  modified to match the chip's OTP settings).
+- interrupt-parent : Specifies the reference to the interrupt controller for
+  the DA9063.
+- interrupts : IRQ line information.
+- interrupt-controller
+
+Sub-nodes:
+
+- regulators : This node defines the settings for the LDOs and BUCKs. The
+  DA9063 regulators are bound using their names listed below:
+
+    bcore1    : BUCK CORE1
+    bcore2    : BUCK CORE2
+    bpro      : BUCK PRO
+    bmem      : BUCK MEM
+    bio       : BUCK IO
+    bperi     : BUCK PERI
+    ldo1      : LDO_1
+    ldo2      : LDO_2
+    ldo3      : LDO_3
+    ldo4      : LDO_4
+    ldo5      : LDO_5
+    ldo6      : LDO_6
+    ldo7      : LDO_7
+    ldo8      : LDO_8
+    ldo9      : LDO_9
+    ldo10     : LDO_10
+    ldo11     : LDO_11
+
+  The component follows the standard regulator framework and the bindings
+  details of individual regulator device can be found in:
+  Documentation/devicetree/bindings/regulator/regulator.txt
+
+- rtc : This node defines settings for the Real-Time Clock associated with
+  the DA9063. There are currently no entries in this binding, however
+  compatible = "dlg,da9063-rtc" should be added if a node is created.
+
+- watchdog : This node defines settings for the Watchdog timer associated
+  with the DA9063. There are currently no entries in this binding, however
+  compatible = "dlg,da9063-watchdog" should be added if a node is created.
+
+
+Example:
+
+	pmic0: da9063@58 {
+		compatible = "dlg,da9063"
+		reg = <0x58>;
+		interrupt-parent = <&gpio6>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-controller;
+
+		rtc {
+			compatible = "dlg,da9063-rtc";
+		};
+
+		wdt {
+			compatible = "dlg,da9063-watchdog";
+		};
+
+		regulators {
+			DA9063_BCORE1: bcore1 {
+				regulator-name = "BCORE1";
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1570000>;
+				regulator-min-microamp = <500000>;
+				regulator-max-microamp = <2000000>;
+				regulator-boot-on;
+			};
+			DA9063_LDO11: ldo11 {
+				regulator-name = "LDO_11";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <3600000>;
+				regulator-boot-on;
+			};
+		};
+	};
+
diff --git a/dts/Bindings/mfd/max77686.txt b/dts/Bindings/mfd/max77686.txt
index 75fdfaf418..e39f0bc1f5 100644
--- a/dts/Bindings/mfd/max77686.txt
+++ b/dts/Bindings/mfd/max77686.txt
@@ -39,6 +39,12 @@ to get matched with their hardware counterparts as follow:
 	-BUCKn	:	1-4.
   Use standard regulator bindings for it ('regulator-off-in-suspend').
 
+  LDO20, LDO21, LDO22, BUCK8 and BUCK9 can be configured to GPIO enable
+  control. To turn this feature on this property must be added to the regulator
+  sub-node:
+	- maxim,ena-gpios :	one GPIO specifier enable control (the gpio
+				flags are actually ignored and always
+				ACTIVE_HIGH is used)
 
 Example:
 
@@ -65,4 +71,12 @@ Example:
 				regulator-always-on;
 				regulator-boot-on;
 			};
+
+			buck9_reg {
+				regulator-compatible = "BUCK9";
+				regulator-name = "CAM_ISP_CORE_1.2V";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1200000>;
+				maxim,ena-gpios = <&gpm0 3 GPIO_ACTIVE_HIGH>;
+			};
 	}
diff --git a/dts/Bindings/mfd/max77693.txt b/dts/Bindings/mfd/max77693.txt
index 01e9f30fe6..38e64405e9 100644
--- a/dts/Bindings/mfd/max77693.txt
+++ b/dts/Bindings/mfd/max77693.txt
@@ -41,6 +41,41 @@ Optional properties:
 	 To get more informations, please refer to documentaion.
 	[*] refer Documentation/devicetree/bindings/pwm/pwm.txt
 
+- charger : Node configuring the charger driver.
+  If present, required properties:
+  - compatible : Must be "maxim,max77693-charger".
+
+  Optional properties (if not set, defaults will be used):
+  - maxim,constant-microvolt : Battery constant voltage in uV. The charger
+    will operate in fast charge constant current mode till battery voltage
+    reaches this level. Then the charger will switch to fast charge constant
+    voltage mode. Also vsys (system voltage) will be set to this value when
+    DC power is supplied but charger is not enabled.
+    Valid values: 3650000 - 4400000, step by 25000 (rounded down)
+    Default: 4200000
+
+  - maxim,min-system-microvolt : Minimal system voltage in uV.
+    Valid values: 3000000 - 3700000, step by 100000 (rounded down)
+    Default: 3600000
+
+  - maxim,thermal-regulation-celsius : Temperature in Celsius for entering
+    high temperature charging mode. If die temperature exceeds this value
+    the charging current will be reduced by 105 mA/Celsius.
+    Valid values: 70, 85, 100, 115
+    Default: 100
+
+  - maxim,battery-overcurrent-microamp : Overcurrent protection threshold
+    in uA (current from battery to system).
+    Valid values: 2000000 - 3500000, step by 250000 (rounded down)
+    Default: 3500000
+
+  - maxim,charge-input-threshold-microvolt : Threshold voltage in uV for
+    triggering input voltage regulation loop. If input voltage decreases
+    below this value, the input current will be reduced to reach the
+    threshold voltage.
+    Valid values: 4300000, 4700000, 4800000, 4900000
+    Default: 4300000
+
 Example:
 	max77693@66 {
 		compatible = "maxim,max77693";
@@ -73,4 +108,14 @@ Example:
 			pwms = <&pwm 0 40000 0>;
 			pwm-names = "haptic";
 		};
+
+		charger {
+			compatible = "maxim,max77693-charger";
+
+			maxim,constant-microvolt = <4200000>;
+			maxim,min-system-microvolt = <3600000>;
+			maxim,thermal-regulation-celsius = <75>;
+			maxim,battery-overcurrent-microamp = <3000000>;
+			maxim,charge-input-threshold-microvolt = <4300000>;
+		};
 	};
diff --git a/dts/Bindings/mfd/qcom-rpm.txt b/dts/Bindings/mfd/qcom-rpm.txt
new file mode 100644
index 0000000000..85e3198001
--- /dev/null
+++ b/dts/Bindings/mfd/qcom-rpm.txt
@@ -0,0 +1,70 @@
+Qualcomm Resource Power Manager (RPM)
+
+This driver is used to interface with the Resource Power Manager (RPM) found in
+various Qualcomm platforms. The RPM allows each component in the system to vote
+for state of the system resources, such as clocks, regulators and bus
+frequencies.
+
+- compatible:
+	Usage: required
+	Value type: <string>
+	Definition: must be one of:
+		    "qcom,rpm-apq8064"
+		    "qcom,rpm-msm8660"
+		    "qcom,rpm-msm8960"
+
+- reg:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: base address and size of the RPM's message ram
+
+- interrupts:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: three entries specifying the RPM's:
+		    1. acknowledgement interrupt
+		    2. error interrupt
+		    3. wakeup interrupt
+
+- interrupt-names:
+	Usage: required
+	Value type: <string-array>
+	Definition: must be the three strings "ack", "err" and "wakeup", in order
+
+- #address-cells:
+	Usage: required
+	Value type: <u32>
+	Definition: must be 1
+
+- #size-cells:
+	Usage: required
+	Value type: <u32>
+	Definition: must be 0
+
+- qcom,ipc:
+	Usage: required
+	Value type: <prop-encoded-array>
+
+	Definition: three entries specifying the outgoing ipc bit used for
+		    signaling the RPM:
+		    - phandle to a syscon node representing the apcs registers
+		    - u32 representing offset to the register within the syscon
+		    - u32 representing the ipc bit within the register
+
+
+= EXAMPLE
+
+	#include <dt-bindings/mfd/qcom-rpm.h>
+
+	rpm@108000 {
+		compatible = "qcom,rpm-msm8960";
+		reg = <0x108000 0x1000>;
+		qcom,ipc = <&apcs 0x8 2>;
+
+		interrupts = <0 19 0>, <0 21 0>, <0 22 0>;
+		interrupt-names = "ack", "err", "wakeup";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+