dts: update to v4.11-rc1

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

9 files changed, 81 insertions, 4 deletions

diff --git a/dts/Bindings/mmc/amlogic,meson-gx.txt b/dts/Bindings/mmc/amlogic,meson-gx.txt
index 7f95ec4008..50bf611a4d 100644
--- a/dts/Bindings/mmc/amlogic,meson-gx.txt
+++ b/dts/Bindings/mmc/amlogic,meson-gx.txt
@@ -17,7 +17,7 @@ Required properties:
 	"core" - Main peripheral bus clock
 	"clkin0" - Parent clock of internal mux
 	"clkin1" - Other parent clock of internal mux
-  The driver has an interal mux clock which switches between clkin0 and clkin1 depending on the
+  The driver has an internal mux clock which switches between clkin0 and clkin1 depending on the
   clock rate requested by the MMC core.
 
 Example:
diff --git a/dts/Bindings/mmc/mmc-pwrseq-sd8787.txt b/dts/Bindings/mmc/mmc-pwrseq-sd8787.txt
new file mode 100644
index 0000000000..22e9340e4b
--- /dev/null
+++ b/dts/Bindings/mmc/mmc-pwrseq-sd8787.txt
@@ -0,0 +1,16 @@
+* Marvell SD8787 power sequence provider
+
+Required properties:
+- compatible: must be "mmc-pwrseq-sd8787".
+- powerdown-gpios: contains a power down GPIO specifier with the
+		   default active state
+- reset-gpios: contains a reset GPIO specifier with the default
+		   active state
+
+Example:
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-sd8787";
+		powerdown-gpios = <&twl_gpio 0 GPIO_ACTIVE_LOW>;
+		reset-gpios = <&twl_gpio 1 GPIO_ACTIVE_LOW>;
+	}
diff --git a/dts/Bindings/mmc/mmc.txt b/dts/Bindings/mmc/mmc.txt
index 8a37782769..c7f4a0ec48 100644
--- a/dts/Bindings/mmc/mmc.txt
+++ b/dts/Bindings/mmc/mmc.txt
@@ -40,6 +40,7 @@ Optional properties:
 - cap-mmc-hw-reset: eMMC hardware reset is supported
 - cap-sdio-irq: enable SDIO IRQ signalling on this interface
 - full-pwr-cycle: full power cycle of the card is supported
+- mmc-ddr-3_3v: eMMC high-speed DDR mode(3.3V I/O) is supported
 - mmc-ddr-1_8v: eMMC high-speed DDR mode(1.8V I/O) is supported
 - mmc-ddr-1_2v: eMMC high-speed DDR mode(1.2V I/O) is supported
 - mmc-hs200-1_8v: eMMC HS200 mode(1.8V I/O) is supported
diff --git a/dts/Bindings/mmc/sdhci-st.txt b/dts/Bindings/mmc/sdhci-st.txt
index 3cd4c43a32..230fd696eb 100644
--- a/dts/Bindings/mmc/sdhci-st.txt
+++ b/dts/Bindings/mmc/sdhci-st.txt
@@ -38,7 +38,7 @@ Optional properties:
 - bus-width:		Number of data lines.
 			See:  Documentation/devicetree/bindings/mmc/mmc.txt.
 
-- max-frequency:	Can be 200MHz, 100Mz or 50MHz (default) and used for
+- max-frequency:	Can be 200MHz, 100MHz or 50MHz (default) and used for
 			configuring the CCONFIG3 in the mmcss.
 			See:  Documentation/devicetree/bindings/mmc/mmc.txt.
 
diff --git a/dts/Bindings/mmc/sdhci.txt b/dts/Bindings/mmc/sdhci.txt
index 1c95a1a555..0e9923a640 100644
--- a/dts/Bindings/mmc/sdhci.txt
+++ b/dts/Bindings/mmc/sdhci.txt
@@ -5,7 +5,7 @@ host controllers refer to the mmc[1] bindings.
 
 Optional properties:
 - sdhci-caps-mask: The sdhci capabilities register is incorrect. This 64bit
-  property corresponds to the bits in the sdhci capabilty register. If the bit
+  property corresponds to the bits in the sdhci capability register. If the bit
   is on in the mask then the bit is incorrect in the register and should be
   turned off, before applying sdhci-caps.
 - sdhci-caps: The sdhci capabilities register is incorrect. This 64bit
diff --git a/dts/Bindings/mmc/sunxi-mmc.txt b/dts/Bindings/mmc/sunxi-mmc.txt
index 55cdd804cd..7d53a799f1 100644
--- a/dts/Bindings/mmc/sunxi-mmc.txt
+++ b/dts/Bindings/mmc/sunxi-mmc.txt
@@ -13,6 +13,7 @@ Required properties:
    * "allwinner,sun5i-a13-mmc"
    * "allwinner,sun7i-a20-mmc"
    * "allwinner,sun9i-a80-mmc"
+   * "allwinner,sun50i-a64-emmc"
    * "allwinner,sun50i-a64-mmc"
  - reg : mmc controller base registers
  - clocks : a list with 4 phandle + clock specifier pairs
diff --git a/dts/Bindings/mmc/synopsys-dw-mshc.txt b/dts/Bindings/mmc/synopsys-dw-mshc.txt
index 7fd17c3da1..9cb55ca574 100644
--- a/dts/Bindings/mmc/synopsys-dw-mshc.txt
+++ b/dts/Bindings/mmc/synopsys-dw-mshc.txt
@@ -16,7 +16,7 @@ Required Properties:
   each child-node representing a supported slot. There should be atleast one
   child node representing a card slot. The name of the child node representing
   the slot is recommended to be slot@n where n is the unique number of the slot
-  connnected to the controller. The following are optional properties which
+  connected to the controller. The following are optional properties which
   can be included in the slot child node.
 
 	* reg: specifies the physical slot number. The valid values of this
@@ -75,6 +75,17 @@ Optional properties:
 * card-detect-delay: Delay in milli-seconds before detecting card after card
   insert event. The default value is 0.
 
+* data-addr: Override fifo address with value provided by DT. The default FIFO reg
+  offset is assumed as 0x100 (version < 0x240A) and 0x200(version >= 0x240A) by
+  driver. If the controller does not follow this rule, please use this property
+  to set fifo address in device tree.
+
+* fifo-watermark-aligned: Data done irq is expected if data length is less than
+  watermark in PIO mode. But fifo watermark is requested to be aligned with data
+  length in some SoC so that TX/RX irq can be generated with data done irq. Add this
+  watermark quirk to mark this requirement and force fifo watermark setting
+  accordingly.
+
 * vmmc-supply: The phandle to the regulator to use for vmmc.  If this is
   specified we'll defer probe until we can find this regulator.
 
@@ -102,6 +113,8 @@ board specific portions as listed below.
 		interrupts = <0 75 0>;
 		#address-cells = <1>;
 		#size-cells = <0>;
+		data-addr = <0x200>;
+		fifo-watermark-aligned;
 		resets = <&rst 20>;
 		reset-names = "reset";
 	};
diff --git a/dts/Bindings/mmc/tmio_mmc.txt b/dts/Bindings/mmc/tmio_mmc.txt
index a1650edfd2..4fd8b7acc5 100644
--- a/dts/Bindings/mmc/tmio_mmc.txt
+++ b/dts/Bindings/mmc/tmio_mmc.txt
@@ -25,6 +25,19 @@ Required properties:
 		"renesas,sdhi-r8a7795" - SDHI IP on R8A7795 SoC
 		"renesas,sdhi-r8a7796" - SDHI IP on R8A7796 SoC
 
+- clocks: Most controllers only have 1 clock source per channel. However, on
+	  some variations of this controller, the internal card detection
+	  logic that exists in this controller is sectioned off to be run by a
+	  separate second clock source to allow the main core clock to be turned
+	  off to save power.
+	  If 2 clocks are specified by the hardware, you must name them as
+	  "core" and "cd". If the controller only has 1 clock, naming is not
+	  required.
+	  Below is the number clocks for each supported SoC:
+	   1: SH73A0, R8A73A4, R8A7740, R8A7778, R8A7779, R8A7790
+	      R8A7791, R8A7792, R8A7793, R8A7794, R8A7795, R8A7796
+	   2: R7S72100
+
 Optional properties:
 - toshiba,mmc-wrprotect-disable: write-protect detection is unavailable
 - pinctrl-names: should be "default", "state_uhs"
diff --git a/dts/Bindings/mmc/zx-dw-mshc.txt b/dts/Bindings/mmc/zx-dw-mshc.txt
new file mode 100644
index 0000000000..eaade0e5ad
--- /dev/null
+++ b/dts/Bindings/mmc/zx-dw-mshc.txt
@@ -0,0 +1,33 @@
+* ZTE specific extensions to the Synopsys Designware Mobile Storage
+  Host Controller
+
+The Synopsys designware mobile storage host controller is used to interface
+a SoC with storage medium such as eMMC or SD/MMC cards. This file documents
+differences between the core Synopsys dw mshc controller properties described
+by synopsys-dw-mshc.txt and the properties used by the ZTE specific
+extensions to the Synopsys Designware Mobile Storage Host Controller.
+
+Required Properties:
+
+* compatible: should be
+	- "zte,zx296718-dw-mshc": for ZX SoCs
+
+Example:
+
+	mmc1: mmc@1110000 {
+		compatible = "zte,zx296718-dw-mshc";
+		reg = <0x01110000 0x1000>;
+		interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
+		fifo-depth = <32>;
+		data-addr = <0x200>;
+		fifo-watermark-aligned;
+		bus-width = <4>;
+		clock-frequency = <50000000>;
+		clocks = <&topcrm SD0_AHB>, <&topcrm SD0_WCLK>;
+		clock-names = "biu", "ciu";
+		num-slots = <1>;
+		max-frequency = <50000000>;
+		cap-sdio-irq;
+		cap-sd-highspeed;
+		status = "disabled";
+	};