Add devicetree source files as of Linux-3.15-rc2

This adds the Linux dts files to barebox. The dts files are
generated from Ian Campbells device-tree-rebasing.git:

git://xenbits.xen.org/people/ianc/device-tree-rebasing.git

The dts are found in dts/ in the barebox repository and
will be updated from upstream regularly, probably for each upstream
-rc.

To keep the synchronization with upstream easy no changes to
the original files are allowed under dts/. Instead changes to
upstream dts files will be done using overlays in arch/$ARCH/dts/.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

25 files changed, 1234 insertions, 0 deletions

diff --git a/dts/Bindings/mtd/arm-versatile.txt b/dts/Bindings/mtd/arm-versatile.txt
new file mode 100644
index 0000000000..beace4b89d
--- /dev/null
+++ b/dts/Bindings/mtd/arm-versatile.txt
@@ -0,0 +1,8 @@
+Flash device on ARM Versatile board
+
+Required properties:
+- compatible : must be "arm,versatile-flash";
+- bank-width : width in bytes of flash interface.
+
+The device tree may optionally contain sub-nodes describing partitions of the
+address space. See partition.txt for more detail.
diff --git a/dts/Bindings/mtd/atmel-dataflash.txt b/dts/Bindings/mtd/atmel-dataflash.txt
new file mode 100644
index 0000000000..1889a4db5b
--- /dev/null
+++ b/dts/Bindings/mtd/atmel-dataflash.txt
@@ -0,0 +1,17 @@
+* Atmel Data Flash
+
+Required properties:
+- compatible : "atmel,<model>", "atmel,<series>", "atmel,dataflash".
+
+The device tree may optionally contain sub-nodes describing partitions of the
+address space. See partition.txt for more detail.
+
+Example:
+
+flash@1 {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "atmel,at45db321d", "atmel,at45", "atmel,dataflash";
+	spi-max-frequency = <25000000>;
+	reg = <1>;
+};
diff --git a/dts/Bindings/mtd/atmel-nand.txt b/dts/Bindings/mtd/atmel-nand.txt
new file mode 100644
index 0000000000..c4728839d0
--- /dev/null
+++ b/dts/Bindings/mtd/atmel-nand.txt
@@ -0,0 +1,107 @@
+Atmel NAND flash
+
+Required properties:
+- compatible : "atmel,at91rm9200-nand".
+- reg : should specify localbus address and size used for the chip,
+	and hardware ECC controller if available.
+	If the hardware ECC is PMECC, it should contain address and size for
+	PMECC, PMECC Error Location controller and ROM which has lookup tables.
+- atmel,nand-addr-offset : offset for the address latch.
+- atmel,nand-cmd-offset : offset for the command latch.
+- #address-cells, #size-cells : Must be present if the device has sub-nodes
+  representing partitions.
+
+- gpios : specifies the gpio pins to control the NAND device. detect is an
+  optional gpio and may be set to 0 if not present.
+
+Optional properties:
+- atmel,nand-has-dma : boolean to support dma transfer for nand read/write.
+- nand-ecc-mode : String, operation mode of the NAND ecc mode, soft by default.
+  Supported values are: "none", "soft", "hw", "hw_syndrome", "hw_oob_first",
+  "soft_bch".
+- atmel,has-pmecc : boolean to enable Programmable Multibit ECC hardware.
+  Only supported by at91sam9x5 or later sam9 product.
+- atmel,pmecc-cap : error correct capability for Programmable Multibit ECC
+  Controller. Supported values are: 2, 4, 8, 12, 24.
+- atmel,pmecc-sector-size : sector size for ECC computation. Supported values
+  are: 512, 1024.
+- atmel,pmecc-lookup-table-offset : includes two offsets of lookup table in ROM
+  for different sector size. First one is for sector size 512, the next is for
+  sector size 1024.
+- nand-bus-width : 8 or 16 bus width if not present 8
+- nand-on-flash-bbt: boolean to enable on flash bbt option if not present false
+- Nand Flash Controller(NFC) is a slave driver under Atmel nand flash
+  - Required properties:
+    - compatible : "atmel,sama5d3-nfc".
+    - reg : should specify the address and size used for NFC command registers,
+            NFC registers and NFC Sram. NFC Sram address and size can be absent
+            if don't want to use it.
+  - Optional properties:
+    - atmel,write-by-sram: boolean to enable NFC write by sram.
+
+Examples:
+nand0: nand@40000000,0 {
+	compatible = "atmel,at91rm9200-nand";
+	#address-cells = <1>;
+	#size-cells = <1>;
+	reg = <0x40000000 0x10000000
+	       0xffffe800 0x200
+	      >;
+	atmel,nand-addr-offset = <21>;	/* ale */
+	atmel,nand-cmd-offset = <22>;	/* cle */
+	nand-on-flash-bbt;
+	nand-ecc-mode = "soft";
+	gpios = <&pioC 13 0	/* rdy */
+		 &pioC 14 0 	/* nce */
+		 0		/* cd */
+		>;
+	partition@0 {
+		...
+	};
+};
+
+/* for PMECC supported chips */
+nand0: nand@40000000 {
+	compatible = "atmel,at91rm9200-nand";
+	#address-cells = <1>;
+	#size-cells = <1>;
+	reg = < 0x40000000 0x10000000	/* bus addr & size */
+		0xffffe000 0x00000600	/* PMECC addr & size */
+		0xffffe600 0x00000200	/* PMECC ERRLOC addr & size */
+		0x00100000 0x00100000	/* ROM addr & size */
+		>;
+	atmel,nand-addr-offset = <21>;	/* ale */
+	atmel,nand-cmd-offset = <22>;	/* cle */
+	nand-on-flash-bbt;
+	nand-ecc-mode = "hw";
+	atmel,has-pmecc;	/* enable PMECC */
+	atmel,pmecc-cap = <2>;
+	atmel,pmecc-sector-size = <512>;
+	atmel,pmecc-lookup-table-offset = <0x8000 0x10000>;
+	gpios = <&pioD 5 0	/* rdy */
+		 &pioD 4 0	/* nce */
+		 0		/* cd */
+		>;
+	partition@0 {
+		...
+	};
+};
+
+/* for NFC supported chips */
+nand0: nand@40000000 {
+	compatible = "atmel,at91rm9200-nand";
+	#address-cells = <1>;
+	#size-cells = <1>;
+	ranges;
+        ...
+        nfc@70000000 {
+		compatible = "atmel,sama5d3-nfc";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <
+			0x70000000 0x10000000	/* NFC Command Registers */
+			0xffffc000 0x00000070	/* NFC HSMC regs */
+			0x00200000 0x00100000	/* NFC SRAM banks */
+		>;
+	};
+};
diff --git a/dts/Bindings/mtd/davinci-nand.txt b/dts/Bindings/mtd/davinci-nand.txt
new file mode 100644
index 0000000000..cfb18abe60
--- /dev/null
+++ b/dts/Bindings/mtd/davinci-nand.txt
@@ -0,0 +1,94 @@
+Device tree bindings for Texas instruments Davinci/Keystone NAND controller
+
+This file provides information, what the device node for the davinci/keystone
+NAND interface contains.
+
+Documentation:
+Davinci DM646x - http://www.ti.com/lit/ug/sprueq7c/sprueq7c.pdf
+Kestone - http://www.ti.com/lit/ug/sprugz3a/sprugz3a.pdf
+
+Required properties:
+
+- compatible:			"ti,davinci-nand"
+				"ti,keystone-nand"
+
+- reg:				Contains 2 offset/length values:
+				- offset and length for the access window.
+				- offset and length for accessing the AEMIF
+				control registers.
+
+- ti,davinci-chipselect:	number of chipselect. Indicates on the
+				davinci_nand driver which chipselect is used
+				for accessing the nand.
+				Can be in the range [0-3].
+
+Recommended properties :
+
+- ti,davinci-mask-ale:		mask for ALE. Needed for executing address
+				phase. These offset will be added to the base
+				address for the chip select space the NAND Flash
+				device is connected to.
+				If not set equal to 0x08.
+
+- ti,davinci-mask-cle:		mask for CLE. Needed for executing command
+				phase. These offset will be added to the base
+				address for the chip select space the NAND Flash
+				device is connected to.
+				If not set equal to 0x10.
+
+- ti,davinci-mask-chipsel:	mask for chipselect address. Needed to mask
+				addresses for given chipselect.
+
+- nand-ecc-mode:		operation mode of the NAND ecc mode. ECC mode
+				valid values for davinci driver:
+				- "none"
+				- "soft"
+				- "hw"
+
+- ti,davinci-ecc-bits:		used ECC bits, currently supported 1 or 4.
+
+- nand-bus-width:		buswidth 8 or 16. If not present 8.
+
+- nand-on-flash-bbt:		use flash based bad block table support. OOB
+				identifier is saved in OOB area. If not present
+				false.
+
+Deprecated properties:
+
+- ti,davinci-ecc-mode:		operation mode of the NAND ecc mode. ECC mode
+				valid values for davinci driver:
+				- "none"
+				- "soft"
+				- "hw"
+
+- ti,davinci-nand-buswidth:	buswidth 8 or 16. If not present 8.
+
+- ti,davinci-nand-use-bbt:	use flash based bad block table support. OOB
+				identifier is saved in OOB area. If not present
+				false.
+
+Nand device bindings may contain additional sub-nodes describing partitions of
+the address space. See partition.txt for more detail. The NAND Flash timing
+values must be programmed in the chip select’s node of AEMIF
+memory-controller (see Documentation/devicetree/bindings/memory-controllers/
+davinci-aemif.txt).
+
+Example(da850 EVM ):
+
+nand_cs3@62000000 {
+	compatible = "ti,davinci-nand";
+	reg = <0x62000000 0x807ff
+	       0x68000000 0x8000>;
+	ti,davinci-chipselect = <1>;
+	ti,davinci-mask-ale = <0>;
+	ti,davinci-mask-cle = <0>;
+	ti,davinci-mask-chipsel = <0>;
+	nand-ecc-mode = "hw";
+	ti,davinci-ecc-bits = <4>;
+	nand-on-flash-bbt;
+
+	partition@180000 {
+		label = "ubifs";
+		reg = <0x180000 0x7e80000>;
+	};
+};
diff --git a/dts/Bindings/mtd/denali-nand.txt b/dts/Bindings/mtd/denali-nand.txt
new file mode 100644
index 0000000000..b04d03a1d4
--- /dev/null
+++ b/dts/Bindings/mtd/denali-nand.txt
@@ -0,0 +1,23 @@
+* Denali NAND controller
+
+Required properties:
+  - compatible : should be "denali,denali-nand-dt"
+  - reg : should contain registers location and length for data and reg.
+  - reg-names: Should contain the reg names "nand_data" and "denali_reg"
+  - interrupts : The interrupt number.
+  - dm-mask : DMA bit mask
+
+The device tree may optionally contain sub-nodes describing partitions of the
+address space. See partition.txt for more detail.
+
+Examples:
+
+nand: nand@ff900000 {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "denali,denali-nand-dt";
+	reg = <0xff900000 0x100000>, <0xffb80000 0x10000>;
+	reg-names = "nand_data", "denali_reg";
+	interrupts = <0 144 4>;
+	dma-mask = <0xffffffff>;
+};
diff --git a/dts/Bindings/mtd/elm.txt b/dts/Bindings/mtd/elm.txt
new file mode 100644
index 0000000000..8c1528c421
--- /dev/null
+++ b/dts/Bindings/mtd/elm.txt
@@ -0,0 +1,16 @@
+Error location module
+
+Required properties:
+- compatible: Must be "ti,am33xx-elm"
+- reg: physical base address and size of the registers map.
+- interrupts: Interrupt number for the elm.
+
+Optional properties:
+- ti,hwmods: Name of the hwmod associated to the elm
+
+Example:
+elm: elm@0 {
+	compatible = "ti,am3352-elm";
+	reg = <0x48080000 0x2000>;
+	interrupts = <4>;
+};
diff --git a/dts/Bindings/mtd/flctl-nand.txt b/dts/Bindings/mtd/flctl-nand.txt
new file mode 100644
index 0000000000..427f46dc60
--- /dev/null
+++ b/dts/Bindings/mtd/flctl-nand.txt
@@ -0,0 +1,49 @@
+FLCTL NAND controller
+
+Required properties:
+- compatible : "renesas,shmobile-flctl-sh7372"
+- reg : Address range of the FLCTL
+- interrupts : flste IRQ number
+- nand-bus-width : bus width to NAND chip
+
+Optional properties:
+- dmas: DMA specifier(s)
+- dma-names: name for each DMA specifier. Valid names are
+	     "data_tx", "data_rx", "ecc_tx", "ecc_rx"
+
+The DMA fields are not used yet in the driver but are listed here for
+completing the bindings.
+
+The device tree may optionally contain sub-nodes describing partitions of the
+address space. See partition.txt for more detail.
+
+Example:
+
+	flctl@e6a30000 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "renesas,shmobile-flctl-sh7372";
+		reg = <0xe6a30000 0x100>;
+		interrupts = <0x0d80>;
+
+		nand-bus-width = <16>;
+
+		dmas = <&dmac 1 /* data_tx */
+			&dmac 2;> /* data_rx */
+		dma-names = "data_tx", "data_rx";
+
+		system@0 {
+			label = "system";
+			reg = <0x0 0x8000000>;
+		};
+
+		userdata@8000000 {
+			label = "userdata";
+			reg = <0x8000000 0x10000000>;
+		};
+
+		cache@18000000 {
+			label = "cache";
+			reg = <0x18000000 0x8000000>;
+		};
+	};
diff --git a/dts/Bindings/mtd/fsl-upm-nand.txt b/dts/Bindings/mtd/fsl-upm-nand.txt
new file mode 100644
index 0000000000..fce4894f5a
--- /dev/null
+++ b/dts/Bindings/mtd/fsl-upm-nand.txt
@@ -0,0 +1,67 @@
+Freescale Localbus UPM programmed to work with NAND flash
+
+Required properties:
+- compatible : "fsl,upm-nand".
+- reg : should specify localbus chip select and size used for the chip.
+- fsl,upm-addr-offset : UPM pattern offset for the address latch.
+- fsl,upm-cmd-offset : UPM pattern offset for the command latch.
+
+Optional properties:
+- fsl,upm-wait-flags : add chip-dependent short delays after running the
+	UPM pattern (0x1), after writing a data byte (0x2) or after
+	writing out a buffer (0x4).
+- fsl,upm-addr-line-cs-offsets : address offsets for multi-chip support.
+	The corresponding address lines are used to select the chip.
+- gpios : may specify optional GPIOs connected to the Ready-Not-Busy pins
+	(R/B#). For multi-chip devices, "n" GPIO definitions are required
+	according to the number of chips.
+- chip-delay : chip dependent delay for transferring data from array to
+	read registers (tR). Required if property "gpios" is not used
+	(R/B# pins not connected).
+
+Each flash chip described may optionally contain additional sub-nodes
+describing partitions of the address space. See partition.txt for more
+detail.
+
+Examples:
+
+upm@1,0 {
+	compatible = "fsl,upm-nand";
+	reg = <1 0 1>;
+	fsl,upm-addr-offset = <16>;
+	fsl,upm-cmd-offset = <8>;
+	gpios = <&qe_pio_e 18 0>;
+
+	flash {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "...";
+
+		partition@0 {
+			...
+		};
+	};
+};
+
+upm@3,0 {
+	#address-cells = <0>;
+	#size-cells = <0>;
+	compatible = "tqc,tqm8548-upm-nand", "fsl,upm-nand";
+	reg = <3 0x0 0x800>;
+	fsl,upm-addr-offset = <0x10>;
+	fsl,upm-cmd-offset = <0x08>;
+	/* Multi-chip NAND device */
+	fsl,upm-addr-line-cs-offsets = <0x0 0x200>;
+	fsl,upm-wait-flags = <0x5>;
+	chip-delay = <25>; // in micro-seconds
+
+	nand@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		partition@0 {
+			    label = "fs";
+			    reg = <0x00000000 0x10000000>;
+		};
+	};
+};
diff --git a/dts/Bindings/mtd/fsmc-nand.txt b/dts/Bindings/mtd/fsmc-nand.txt
new file mode 100644
index 0000000000..ec42935f39
--- /dev/null
+++ b/dts/Bindings/mtd/fsmc-nand.txt
@@ -0,0 +1,54 @@
+ST Microelectronics Flexible Static Memory Controller (FSMC)
+NAND Interface
+
+Required properties:
+- compatible : "st,spear600-fsmc-nand", "stericsson,fsmc-nand"
+- reg : Address range of the mtd chip
+- reg-names: Should contain the reg names "fsmc_regs", "nand_data", "nand_addr" and "nand_cmd"
+
+Optional properties:
+- bank-width : Width (in bytes) of the device.  If not present, the width
+  defaults to 1 byte
+- nand-skip-bbtscan: Indicates the the BBT scanning should be skipped
+- timings: array of 6 bytes for NAND timings. The meanings of these bytes
+  are:
+  byte 0 TCLR  : CLE to RE delay in number of AHB clock cycles, only 4 bits
+                 are valid. Zero means one clockcycle, 15 means 16 clock
+                 cycles.
+  byte 1 TAR   : ALE to RE delay, 4 bits are valid. Same format as TCLR.
+  byte 2 THIZ  : number of HCLK clock cycles during which the data bus is
+                 kept in Hi-Z (tristate) after the start of a write access.
+                 Only valid for write transactions. Zero means zero cycles,
+                 255 means 255 cycles.
+  byte 3 THOLD : number of HCLK clock cycles to hold the address (and data
+                 when writing) after the command deassertation. Zero means
+                 one cycle, 255 means 256 cycles.
+  byte 4 TWAIT : number of HCLK clock cycles to assert the command to the
+                 NAND flash in response to SMWAITn. Zero means 1 cycle,
+                 255 means 256 cycles.
+  byte 5 TSET  : number of HCLK clock cycles to assert the address before the
+                 command is asserted. Zero means one cycle, 255 means 256
+                 cycles.
+- bank: default NAND bank to use (0-3 are valid, 0 is the default).
+
+Example:
+
+	fsmc: flash@d1800000 {
+		compatible = "st,spear600-fsmc-nand";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0xd1800000 0x1000	/* FSMC Register */
+		       0xd2000000 0x0010	/* NAND Base DATA */
+		       0xd2020000 0x0010	/* NAND Base ADDR */
+		       0xd2010000 0x0010>;	/* NAND Base CMD */
+		reg-names = "fsmc_regs", "nand_data", "nand_addr", "nand_cmd";
+
+		bank-width = <1>;
+		nand-skip-bbtscan;
+		timings = /bits/ 8 <0 0 0 2 3 0>;
+		bank = <1>;
+
+		partition@0 {
+			...
+		};
+	};
diff --git a/dts/Bindings/mtd/gpio-control-nand.txt b/dts/Bindings/mtd/gpio-control-nand.txt
new file mode 100644
index 0000000000..36ef07d3c9
--- /dev/null
+++ b/dts/Bindings/mtd/gpio-control-nand.txt
@@ -0,0 +1,47 @@
+GPIO assisted NAND flash
+
+The GPIO assisted NAND flash uses a memory mapped interface to
+read/write the NAND commands and data and GPIO pins for the control
+signals.
+
+Required properties:
+- compatible : "gpio-control-nand"
+- reg : should specify localbus chip select and size used for the chip.  The
+  resource describes the data bus connected to the NAND flash and all accesses
+  are made in native endianness.
+- #address-cells, #size-cells : Must be present if the device has sub-nodes
+  representing partitions.
+- gpios : specifies the gpio pins to control the NAND device.  nwp is an
+  optional gpio and may be set to 0 if not present.
+
+Optional properties:
+- bank-width : Width (in bytes) of the device.  If not present, the width
+  defaults to 1 byte.
+- chip-delay : chip dependent delay for transferring data from array to
+  read registers (tR).  If not present then a default of 20us is used.
+- gpio-control-nand,io-sync-reg : A 64-bit physical address for a read
+  location used to guard against bus reordering with regards to accesses to
+  the GPIO's and the NAND flash data bus.  If present, then after changing
+  GPIO state and before and after command byte writes, this register will be
+  read to ensure that the GPIO accesses have completed.
+
+The device tree may optionally contain sub-nodes describing partitions of the
+address space. See partition.txt for more detail.
+
+Examples:
+
+gpio-nand@1,0 {
+	compatible = "gpio-control-nand";
+	reg = <1 0x0000 0x2>;
+	#address-cells = <1>;
+	#size-cells = <1>;
+	gpios = <&banka 1 0	/* rdy */
+		 &banka 2 0 	/* nce */
+		 &banka 3 0 	/* ale */
+		 &banka 4 0 	/* cle */
+		 0		/* nwp */>;
+
+	partition@0 {
+	...
+	};
+};
diff --git a/dts/Bindings/mtd/gpmc-nand.txt b/dts/Bindings/mtd/gpmc-nand.txt
new file mode 100644
index 0000000000..5e1f31b5ff
--- /dev/null
+++ b/dts/Bindings/mtd/gpmc-nand.txt
@@ -0,0 +1,92 @@
+Device tree bindings for GPMC connected NANDs
+
+GPMC connected NAND (found on OMAP boards) are represented as child nodes of
+the GPMC controller with a name of "nand".
+
+All timing relevant properties as well as generic gpmc child properties are
+explained in a separate documents - please refer to
+Documentation/devicetree/bindings/bus/ti-gpmc.txt
+
+For NAND specific properties such as ECC modes or bus width, please refer to
+Documentation/devicetree/bindings/mtd/nand.txt
+
+
+Required properties:
+
+ - reg:		The CS line the peripheral is connected to
+
+Optional properties:
+
+ - nand-bus-width: 		Set this numeric value to 16 if the hardware
+				is wired that way. If not specified, a bus
+				width of 8 is assumed.
+
+ - ti,nand-ecc-opt:		A string setting the ECC layout to use. One of:
+		"sw"		<deprecated> use "ham1" instead
+		"hw"		<deprecated> use "ham1" instead
+		"hw-romcode"	<deprecated> use "ham1" instead
+		"ham1"		1-bit Hamming ecc code
+		"bch4"		4-bit BCH ecc code
+		"bch8"		8-bit BCH ecc code
+
+ - ti,nand-xfer-type:		A string setting the data transfer type. One of:
+
+		"prefetch-polled"	Prefetch polled mode (default)
+		"polled"		Polled mode, without prefetch
+		"prefetch-dma"		Prefetch enabled sDMA mode
+		"prefetch-irq"		Prefetch enabled irq mode
+
+ - elm_id:	<deprecated> use "ti,elm-id" instead
+ - ti,elm-id:	Specifies phandle of the ELM devicetree node.
+		ELM is an on-chip hardware engine on TI SoC which is used for
+		locating ECC errors for BCHx algorithms. SoC devices which have
+		ELM hardware engines should specify this device node in .dtsi
+		Using ELM for ECC error correction frees some CPU cycles.
+
+For inline partiton table parsing (optional):
+
+ - #address-cells: should be set to 1
+ - #size-cells: should be set to 1
+
+Example for an AM33xx board:
+
+	gpmc: gpmc@50000000 {
+		compatible = "ti,am3352-gpmc";
+		ti,hwmods = "gpmc";
+		reg = <0x50000000 0x1000000>;
+		interrupts = <100>;
+		gpmc,num-cs = <8>;
+		gpmc,num-waitpins = <2>;
+		#address-cells = <2>;
+		#size-cells = <1>;
+		ranges = <0 0 0x08000000 0x2000>;	/* CS0: NAND */
+		elm_id = <&elm>;
+
+		nand@0,0 {
+			reg = <0 0 0>; /* CS0, offset 0 */
+			nand-bus-width = <16>;
+			ti,nand-ecc-opt = "bch8";
+			ti,nand-xfer-type = "polled";
+
+			gpmc,sync-clk-ps = <0>;
+			gpmc,cs-on-ns = <0>;
+			gpmc,cs-rd-off-ns = <44>;
+			gpmc,cs-wr-off-ns = <44>;
+			gpmc,adv-on-ns = <6>;
+			gpmc,adv-rd-off-ns = <34>;
+			gpmc,adv-wr-off-ns = <44>;
+			gpmc,we-off-ns = <40>;
+			gpmc,oe-off-ns = <54>;
+			gpmc,access-ns = <64>;
+			gpmc,rd-cycle-ns = <82>;
+			gpmc,wr-cycle-ns = <82>;
+			gpmc,wr-access-ns = <40>;
+			gpmc,wr-data-mux-bus-ns = <0>;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			/* partitions go here */
+		};
+	};
+
diff --git a/dts/Bindings/mtd/gpmc-nor.txt b/dts/Bindings/mtd/gpmc-nor.txt
new file mode 100644
index 0000000000..420b3ab188
--- /dev/null
+++ b/dts/Bindings/mtd/gpmc-nor.txt
@@ -0,0 +1,98 @@
+Device tree bindings for NOR flash connect to TI GPMC
+
+NOR flash connected to the TI GPMC (found on OMAP boards) are represented as
+child nodes of the GPMC controller with a name of "nor".
+
+All timing relevant properties as well as generic GPMC child properties are
+explained in a separate documents. Please refer to
+Documentation/devicetree/bindings/bus/ti-gpmc.txt
+
+Required properties:
+- bank-width: 		Width of NOR flash in bytes. GPMC supports 8-bit and
+			16-bit devices and so must be either 1 or 2 bytes.
+- compatible:		Documentation/devicetree/bindings/mtd/mtd-physmap.txt
+- gpmc,cs-on-ns:		Chip-select assertion time
+- gpmc,cs-rd-off-ns:	Chip-select de-assertion time for reads
+- gpmc,cs-wr-off-ns:	Chip-select de-assertion time for writes
+- gpmc,oe-on-ns:	Output-enable assertion time
+- gpmc,oe-off-ns:	Output-enable de-assertion time
+- gpmc,we-on-ns		Write-enable assertion time
+- gpmc,we-off-ns:	Write-enable de-assertion time
+- gpmc,access-ns:	Start cycle to first data capture (read access)
+- gpmc,rd-cycle-ns:	Total read cycle time
+- gpmc,wr-cycle-ns:	Total write cycle time
+- linux,mtd-name:	Documentation/devicetree/bindings/mtd/mtd-physmap.txt
+- reg:			Chip-select, base address (relative to chip-select)
+			and size of NOR flash. Note that base address will be
+			typically 0 as this is the start of the chip-select.
+
+Optional properties:
+- gpmc,XXX		Additional GPMC timings and settings parameters. See
+			Documentation/devicetree/bindings/bus/ti-gpmc.txt
+
+Optional properties for partiton table parsing:
+- #address-cells: should be set to 1
+- #size-cells: should be set to 1
+
+Example:
+
+gpmc: gpmc@6e000000 {
+	compatible = "ti,omap3430-gpmc", "simple-bus";
+	ti,hwmods = "gpmc";
+	reg = <0x6e000000 0x1000>;
+	interrupts = <20>;
+	gpmc,num-cs = <8>;
+	gpmc,num-waitpins = <4>;
+	#address-cells = <2>;
+	#size-cells = <1>;
+
+	ranges = <0 0 0x10000000 0x08000000>;
+
+	nor@0,0 {
+		compatible = "cfi-flash";
+		linux,mtd-name= "intel,pf48f6000m0y1be";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0 0 0x08000000>;
+		bank-width = <2>;
+
+		gpmc,mux-add-data;
+		gpmc,cs-on-ns = <0>;
+		gpmc,cs-rd-off-ns = <186>;
+		gpmc,cs-wr-off-ns = <186>;
+		gpmc,adv-on-ns = <12>;
+		gpmc,adv-rd-off-ns = <48>;
+		gpmc,adv-wr-off-ns = <48>;
+		gpmc,oe-on-ns = <54>;
+		gpmc,oe-off-ns = <168>;
+		gpmc,we-on-ns = <54>;
+		gpmc,we-off-ns = <168>;
+		gpmc,rd-cycle-ns = <186>;
+		gpmc,wr-cycle-ns = <186>;
+		gpmc,access-ns = <114>;
+		gpmc,page-burst-access-ns = <6>;
+		gpmc,bus-turnaround-ns = <12>;
+		gpmc,cycle2cycle-delay-ns = <18>;
+		gpmc,wr-data-mux-bus-ns = <90>;
+		gpmc,wr-access-ns = <186>;
+		gpmc,cycle2cycle-samecsen;
+		gpmc,cycle2cycle-diffcsen;
+
+		partition@0 {
+			label = "bootloader-nor";
+			reg = <0 0x40000>;
+		};
+		partition@0x40000 {
+			label = "params-nor";
+			reg = <0x40000 0x40000>;
+		};
+		partition@0x80000 {
+			label = "kernel-nor";
+			reg = <0x80000 0x200000>;
+		};
+		partition@0x280000 {
+			label = "filesystem-nor";
+			reg = <0x240000 0x7d80000>;
+		};
+	};
+};
diff --git a/dts/Bindings/mtd/gpmc-onenand.txt b/dts/Bindings/mtd/gpmc-onenand.txt
new file mode 100644
index 0000000000..b7529424ac
--- /dev/null
+++ b/dts/Bindings/mtd/gpmc-onenand.txt
@@ -0,0 +1,46 @@
+Device tree bindings for GPMC connected OneNANDs
+
+GPMC connected OneNAND (found on OMAP boards) are represented as child nodes of
+the GPMC controller with a name of "onenand".
+
+All timing relevant properties as well as generic gpmc child properties are
+explained in a separate documents - please refer to
+Documentation/devicetree/bindings/bus/ti-gpmc.txt
+
+Required properties:
+
+ - reg:			The CS line the peripheral is connected to
+ - gpmc,device-width	Width of the ONENAND device connected to the GPMC
+			in bytes. Must be 1 or 2.
+
+Optional properties:
+
+ - dma-channel:		DMA Channel index
+
+For inline partiton table parsing (optional):
+
+ - #address-cells: should be set to 1
+ - #size-cells: should be set to 1
+
+Example for an OMAP3430 board:
+
+	gpmc: gpmc@6e000000 {
+		compatible = "ti,omap3430-gpmc";
+		ti,hwmods = "gpmc";
+		reg = <0x6e000000 0x1000000>;
+		interrupts = <20>;
+		gpmc,num-cs = <8>;
+		gpmc,num-waitpins = <4>;
+		#address-cells = <2>;
+		#size-cells = <1>;
+
+		onenand@0 {
+			reg = <0 0 0>; /* CS0, offset 0 */
+			gpmc,device-width = <2>;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			/* partitions go here */
+		};
+	};
diff --git a/dts/Bindings/mtd/gpmi-nand.txt b/dts/Bindings/mtd/gpmi-nand.txt
new file mode 100644
index 0000000000..458d596346
--- /dev/null
+++ b/dts/Bindings/mtd/gpmi-nand.txt
@@ -0,0 +1,48 @@
+* Freescale General-Purpose Media Interface (GPMI)
+
+The GPMI nand controller provides an interface to control the
+NAND flash chips. We support only one NAND chip now.
+
+Required properties:
+  - compatible : should be "fsl,<chip>-gpmi-nand"
+  - reg : should contain registers location and length for gpmi and bch.
+  - reg-names: Should contain the reg names "gpmi-nand" and "bch"
+  - interrupts : BCH interrupt number.
+  - interrupt-names : Should be "bch".
+  - dmas: DMA specifier, consisting of a phandle to DMA controller node
+    and GPMI DMA channel ID.
+    Refer to dma.txt and fsl-mxs-dma.txt for details.
+  - dma-names: Must be "rx-tx".
+
+Optional properties:
+  - nand-on-flash-bbt: boolean to enable on flash bbt option if not
+                       present false
+  - fsl,use-minimum-ecc: Protect this NAND flash with the minimum ECC
+                       strength required. The required ECC strength is
+                       automatically discoverable for some flash
+                       (e.g., according to the ONFI standard).
+                       However, note that if this strength is not
+                       discoverable or this property is not enabled,
+                       the software may chooses an implementation-defined
+                       ECC scheme.
+
+The device tree may optionally contain sub-nodes describing partitions of the
+address space. See partition.txt for more detail.
+
+Examples:
+
+gpmi-nand@8000c000 {
+	compatible = "fsl,imx28-gpmi-nand";
+	#address-cells = <1>;
+	#size-cells = <1>;
+	reg = <0x8000c000 2000>, <0x8000a000 2000>;
+	reg-names = "gpmi-nand", "bch";
+	interrupts = <41>;
+	interrupt-names = "bch";
+	dmas = <&dma_apbh 4>;
+	dma-names = "rx-tx";
+
+	partition@0 {
+	...
+	};
+};
diff --git a/dts/Bindings/mtd/lpc32xx-mlc.txt b/dts/Bindings/mtd/lpc32xx-mlc.txt
new file mode 100644
index 0000000000..d0a37252eb
--- /dev/null
+++ b/dts/Bindings/mtd/lpc32xx-mlc.txt
@@ -0,0 +1,50 @@
+NXP LPC32xx SoC NAND MLC controller
+
+Required properties:
+- compatible: "nxp,lpc3220-mlc"
+- reg: Address and size of the controller
+- interrupts: The NAND interrupt specification
+- gpios: GPIO specification for NAND write protect
+
+The following required properties are very controller specific. See the LPC32xx
+User Manual 7.5.14 MLC NAND Timing Register (the values here are specified in
+Hz, to make them independent of actual clock speed and to provide for good
+accuracy:)
+- nxp,tcea_delay: TCEA_DELAY
+- nxp,busy_delay: BUSY_DELAY
+- nxp,nand_ta: NAND_TA
+- nxp,rd_high: RD_HIGH
+- nxp,rd_low: RD_LOW
+- nxp,wr_high: WR_HIGH
+- nxp,wr_low: WR_LOW
+
+Optional subnodes:
+- Partitions, see Documentation/devicetree/bindings/mtd/partition.txt
+
+Example:
+
+	mlc: flash@200A8000 {
+		compatible = "nxp,lpc3220-mlc";
+		reg = <0x200A8000 0x11000>;
+		interrupts = <11 0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		nxp,tcea-delay = <333333333>;
+		nxp,busy-delay = <10000000>;
+		nxp,nand-ta = <18181818>;
+		nxp,rd-high = <31250000>;
+		nxp,rd-low = <45454545>;
+		nxp,wr-high = <40000000>;
+		nxp,wr-low = <83333333>;
+		gpios = <&gpio 5 19 1>; /* GPO_P3 19, active low */
+
+		mtd0@00000000 {
+			label = "boot";
+			reg = <0x00000000 0x00064000>;
+			read-only;
+		};
+
+		...
+
+	};
diff --git a/dts/Bindings/mtd/lpc32xx-slc.txt b/dts/Bindings/mtd/lpc32xx-slc.txt
new file mode 100644
index 0000000000..d94edc0fc5
--- /dev/null
+++ b/dts/Bindings/mtd/lpc32xx-slc.txt
@@ -0,0 +1,52 @@
+NXP LPC32xx SoC NAND SLC controller
+
+Required properties:
+- compatible: "nxp,lpc3220-slc"
+- reg: Address and size of the controller
+- nand-on-flash-bbt: Use bad block table on flash
+- gpios: GPIO specification for NAND write protect
+
+The following required properties are very controller specific. See the LPC32xx
+User Manual:
+- nxp,wdr-clks: Delay before Ready signal is tested on write (W_RDY)
+- nxp,rdr-clks: Delay before Ready signal is tested on read (R_RDY)
+(The following values are specified in Hz, to make them independent of actual
+clock speed:)
+- nxp,wwidth: Write pulse width (W_WIDTH)
+- nxp,whold: Write hold time (W_HOLD)
+- nxp,wsetup: Write setup time (W_SETUP)
+- nxp,rwidth: Read pulse width (R_WIDTH)
+- nxp,rhold: Read hold time (R_HOLD)
+- nxp,rsetup: Read setup time (R_SETUP)
+
+Optional subnodes:
+- Partitions, see Documentation/devicetree/bindings/mtd/partition.txt
+
+Example:
+
+	slc: flash@20020000 {
+		compatible = "nxp,lpc3220-slc";
+		reg = <0x20020000 0x1000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		nxp,wdr-clks = <14>;
+		nxp,wwidth = <40000000>;
+		nxp,whold = <100000000>;
+		nxp,wsetup = <100000000>;
+		nxp,rdr-clks = <14>;
+		nxp,rwidth = <40000000>;
+		nxp,rhold = <66666666>;
+		nxp,rsetup = <100000000>;
+		nand-on-flash-bbt;
+		gpios = <&gpio 5 19 1>; /* GPO_P3 19, active low */
+
+		mtd0@00000000 {
+			label = "phy3250-boot";
+			reg = <0x00000000 0x00064000>;
+			read-only;
+		};
+
+		...
+
+	};
diff --git a/dts/Bindings/mtd/m25p80.txt b/dts/Bindings/mtd/m25p80.txt
new file mode 100644
index 0000000000..6d3d576094
--- /dev/null
+++ b/dts/Bindings/mtd/m25p80.txt
@@ -0,0 +1,29 @@
+* MTD SPI driver for ST M25Pxx (and similar) serial flash chips
+
+Required properties:
+- #address-cells, #size-cells : Must be present if the device has sub-nodes
+  representing partitions.
+- compatible : Should be the manufacturer and the name of the chip. Bear in mind
+               the DT binding is not Linux-only, but in case of Linux, see the
+               "m25p_ids" table in drivers/mtd/devices/m25p80.c for the list of
+               supported chips.
+- reg : Chip-Select number
+- spi-max-frequency : Maximum frequency of the SPI bus the chip can operate at
+
+Optional properties:
+- m25p,fast-read : Use the "fast read" opcode to read data from the chip instead
+                   of the usual "read" opcode. This opcode is not supported by
+                   all chips and support for it can not be detected at runtime.
+                   Refer to your chips' datasheet to check if this is supported
+                   by your chip.
+
+Example:
+
+	flash: m25p80@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "spansion,m25p80";
+		reg = <0>;
+		spi-max-frequency = <40000000>;
+		m25p,fast-read;
+	};
diff --git a/dts/Bindings/mtd/mtd-physmap.txt b/dts/Bindings/mtd/mtd-physmap.txt
new file mode 100644
index 0000000000..61c5ec850f
--- /dev/null
+++ b/dts/Bindings/mtd/mtd-physmap.txt
@@ -0,0 +1,84 @@
+CFI or JEDEC memory-mapped NOR flash, MTD-RAM (NVRAM...)
+
+Flash chips (Memory Technology Devices) are often used for solid state
+file systems on embedded devices.
+
+ - compatible : should contain the specific model of mtd chip(s)
+   used, if known, followed by either "cfi-flash", "jedec-flash"
+   or "mtd-ram".
+ - reg : Address range(s) of the mtd chip(s)
+   It's possible to (optionally) define multiple "reg" tuples so that
+   non-identical chips can be described in one node.
+ - bank-width : Width (in bytes) of the bank.  Equal to the
+   device width times the number of interleaved chips.
+ - device-width : (optional) Width of a single mtd chip.  If
+   omitted, assumed to be equal to 'bank-width'.
+ - #address-cells, #size-cells : Must be present if the device has
+   sub-nodes representing partitions (see below).  In this case
+   both #address-cells and #size-cells must be equal to 1.
+ - no-unaligned-direct-access: boolean to disable the default direct
+   mapping of the flash.
+   On some platforms (e.g. MPC5200) a direct 1:1 mapping may cause
+   problems with JFFS2 usage, as the local bus (LPB) doesn't support
+   unaligned accesses as implemented in the JFFS2 code via memcpy().
+   By defining "no-unaligned-direct-access", the flash will not be
+   exposed directly to the MTD users (e.g. JFFS2) any more.
+ - linux,mtd-name: allow to specify the mtd name for retro capability with
+   physmap-flash drivers as boot loader pass the mtd partition via the old
+   device name physmap-flash.
+ - use-advanced-sector-protection: boolean to enable support for the
+   advanced sector protection (Spansion: PPB - Persistent Protection
+   Bits) locking.
+
+For JEDEC compatible devices, the following additional properties
+are defined:
+
+ - vendor-id : Contains the flash chip's vendor id (1 byte).
+ - device-id : Contains the flash chip's device id (1 byte).
+
+The device tree may optionally contain sub-nodes describing partitions of the
+address space. See partition.txt for more detail.
+
+Example:
+
+	flash@ff000000 {
+		compatible = "amd,am29lv128ml", "cfi-flash";
+		reg = <ff000000 01000000>;
+		bank-width = <4>;
+		device-width = <1>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		fs@0 {
+			label = "fs";
+			reg = <0 f80000>;
+		};
+		firmware@f80000 {
+			label ="firmware";
+			reg = <f80000 80000>;
+			read-only;
+		};
+	};
+
+Here an example with multiple "reg" tuples:
+
+	flash@f0000000,0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "intel,PC48F4400P0VB", "cfi-flash";
+		reg = <0 0x00000000 0x02000000
+		       0 0x02000000 0x02000000>;
+		bank-width = <2>;
+		partition@0 {
+			label = "test-part1";
+			reg = <0 0x04000000>;
+		};
+	};
+
+An example using SRAM:
+
+	sram@2,0 {
+		compatible = "samsung,k6f1616u6a", "mtd-ram";
+		reg = <2 0 0x00200000>;
+		bank-width = <2>;
+	};
+
diff --git a/dts/Bindings/mtd/mxc-nand.txt b/dts/Bindings/mtd/mxc-nand.txt
new file mode 100644
index 0000000000..b5833d11c7
--- /dev/null
+++ b/dts/Bindings/mtd/mxc-nand.txt
@@ -0,0 +1,19 @@
+* Freescale's mxc_nand
+
+Required properties:
+- compatible: "fsl,imxXX-nand"
+- reg: address range of the nfc block
+- interrupts: irq to be used
+- nand-bus-width: see nand.txt
+- nand-ecc-mode: see nand.txt
+- nand-on-flash-bbt: see nand.txt
+
+Example:
+
+	nand@d8000000 {
+		compatible = "fsl,imx27-nand";
+		reg = <0xd8000000 0x1000>;
+		interrupts = <29>;
+		nand-bus-width = <8>;
+		nand-ecc-mode = "hw";
+	};
diff --git a/dts/Bindings/mtd/nand.txt b/dts/Bindings/mtd/nand.txt
new file mode 100644
index 0000000000..b53f92e252
--- /dev/null
+++ b/dts/Bindings/mtd/nand.txt
@@ -0,0 +1,21 @@
+* MTD generic binding
+
+- nand-ecc-mode : String, operation mode of the NAND ecc mode.
+  Supported values are: "none", "soft", "hw", "hw_syndrome", "hw_oob_first",
+  "soft_bch".
+- nand-bus-width : 8 or 16 bus width if not present 8
+- nand-on-flash-bbt: boolean to enable on flash bbt option if not present false
+
+- nand-ecc-strength: integer representing the number of bits to correct
+		     per ECC step.
+
+- nand-ecc-step-size: integer representing the number of data bytes
+		      that are covered by a single ECC step.
+
+The ECC strength and ECC step size properties define the correction capability
+of a controller. Together, they say a controller can correct "{strength} bit
+errors per {size} bytes".
+
+The interpretation of these parameters is implementation-defined, so not all
+implementations must support all possible combinations. However, implementations
+are encouraged to further specify the value(s) they support.
diff --git a/dts/Bindings/mtd/orion-nand.txt b/dts/Bindings/mtd/orion-nand.txt
new file mode 100644
index 0000000000..2d6ab660e6
--- /dev/null
+++ b/dts/Bindings/mtd/orion-nand.txt
@@ -0,0 +1,50 @@
+NAND support for Marvell Orion SoC platforms
+
+Required properties:
+- compatible : "marvell,orion-nand".
+- reg : Base physical address of the NAND and length of memory mapped
+	region
+
+Optional properties:
+- cle : Address line number connected to CLE. Default is 0
+- ale : Address line number connected to ALE. Default is 1
+- bank-width : Width in bytes of the device. Default is 1
+- chip-delay : Chip dependent delay for transferring data from array to read
+               registers in usecs
+
+The device tree may optionally contain sub-nodes describing partitions of the
+address space. See partition.txt for more detail.
+
+Example:
+
+nand@f4000000 {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	cle = <0>;
+	ale = <1>;
+	bank-width = <1>;
+	chip-delay = <25>;
+	compatible = "marvell,orion-nand";
+	reg = <0xf4000000 0x400>;
+
+	partition@0 {
+		label = "u-boot";
+		reg = <0x0000000 0x100000>;
+		read-only;
+	};
+
+	partition@100000 {
+		label = "uImage";
+		reg = <0x0100000 0x200000>;
+	};
+
+	partition@300000 {
+		label = "dtb";
+		reg = <0x0300000 0x100000>;
+	};
+
+	partition@400000 {
+		label = "root";
+		reg = <0x0400000 0x7d00000>;
+	};
+};
diff --git a/dts/Bindings/mtd/partition.txt b/dts/Bindings/mtd/partition.txt
new file mode 100644
index 0000000000..8e5557da19
--- /dev/null
+++ b/dts/Bindings/mtd/partition.txt
@@ -0,0 +1,71 @@
+Representing flash partitions in devicetree
+
+Partitions can be represented by sub-nodes of an mtd device. This can be used
+on platforms which have strong conventions about which portions of a flash are
+used for what purposes, but which don't use an on-flash partition table such
+as RedBoot.
+NOTE: if the sub-node has a compatible string, then it is not a partition.
+
+#address-cells & #size-cells must both be present in the mtd device. There are
+two valid values for both:
+<1>: for partitions that require a single 32-bit cell to represent their
+     size/address (aka the value is below 4 GiB)
+<2>: for partitions that require two 32-bit cells to represent their
+     size/address (aka the value is 4 GiB or greater).
+
+Required properties:
+- reg : The partition's offset and size within the mtd bank.
+
+Optional properties:
+- label : The label / name for this partition.  If omitted, the label is taken
+  from the node name (excluding the unit address).
+- read-only : This parameter, if present, is a hint to Linux that this
+  partition should only be mounted read-only. This is usually used for flash
+  partitions containing early-boot firmware images or data which should not be
+  clobbered.
+
+Examples:
+
+
+flash@0 {
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	partition@0 {
+		label = "u-boot";
+		reg = <0x0000000 0x100000>;
+		read-only;
+	};
+
+	uimage@100000 {
+		reg = <0x0100000 0x200000>;
+	};
+};
+
+flash@1 {
+	#address-cells = <1>;
+	#size-cells = <2>;
+
+	/* a 4 GiB partition */
+	partition@0 {
+		label = "filesystem";
+		reg = <0x00000000 0x1 0x00000000>;
+	};
+};
+
+flash@2 {
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	/* an 8 GiB partition */
+	partition@0 {
+		label = "filesystem #1";
+		reg = <0x0 0x00000000 0x2 0x00000000>;
+	};
+
+	/* a 4 GiB partition */
+	partition@200000000 {
+		label = "filesystem #2";
+		reg = <0x2 0x00000000 0x1 0x00000000>;
+	};
+};
diff --git a/dts/Bindings/mtd/pxa3xx-nand.txt b/dts/Bindings/mtd/pxa3xx-nand.txt
new file mode 100644
index 0000000000..86e0a5601f
--- /dev/null
+++ b/dts/Bindings/mtd/pxa3xx-nand.txt
@@ -0,0 +1,35 @@
+PXA3xx NAND DT bindings
+
+Required properties:
+
+ - compatible:		Should be set to one of the following:
+			marvell,pxa3xx-nand
+			marvell,armada370-nand
+ - reg: 		The register base for the controller
+ - interrupts:		The interrupt to map
+ - #address-cells:	Set to <1> if the node includes partitions
+
+Optional properties:
+
+ - marvell,nand-enable-arbiter:	Set to enable the bus arbiter
+ - marvell,nand-keep-config:	Set to keep the NAND controller config as set
+				by the bootloader
+ - num-cs:			Number of chipselect lines to usw
+ - nand-on-flash-bbt: 		boolean to enable on flash bbt option if
+				not present false
+
+Example:
+
+	nand0: nand@43100000 {
+		compatible = "marvell,pxa3xx-nand";
+		reg = <0x43100000 90>;
+		interrupts = <45>;
+		#address-cells = <1>;
+
+		marvell,nand-enable-arbiter;
+		marvell,nand-keep-config;
+		num-cs = <1>;
+
+		/* partitions (optional) */
+	};
+
diff --git a/dts/Bindings/mtd/spear_smi.txt b/dts/Bindings/mtd/spear_smi.txt
new file mode 100644
index 0000000000..7248aadd89
--- /dev/null
+++ b/dts/Bindings/mtd/spear_smi.txt
@@ -0,0 +1,31 @@
+* SPEAr SMI
+
+Required properties:
+- compatible : "st,spear600-smi"
+- reg : Address range of the mtd chip
+- #address-cells, #size-cells : Must be present if the device has sub-nodes
+  representing partitions.
+- interrupt-parent: Should be the phandle for the interrupt controller
+  that services interrupts for this device
+- interrupts: Should contain the STMMAC interrupts
+- clock-rate : Functional clock rate of SMI in Hz
+
+Optional properties:
+- st,smi-fast-mode : Flash supports read in fast mode
+
+Example:
+
+	smi: flash@fc000000 {
+		compatible = "st,spear600-smi";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0xfc000000 0x1000>;
+		interrupt-parent = <&vic1>;
+		interrupts = <12>;
+		clock-rate = <50000000>;	/* 50MHz */
+
+		flash@f8000000 {
+			st,smi-fast-mode;
+			...
+		};
+	};
diff --git a/dts/Bindings/mtd/st-fsm.txt b/dts/Bindings/mtd/st-fsm.txt
new file mode 100644
index 0000000000..c2489391c4
--- /dev/null
+++ b/dts/Bindings/mtd/st-fsm.txt
@@ -0,0 +1,26 @@
+* ST-Microelectronics SPI FSM Serial (NOR) Flash Controller
+
+Required properties:
+  - compatible : Should be "st,spi-fsm"
+  - reg        : Contains register's location and length.
+  - reg-names  : Should contain the reg names "spi-fsm"
+  - interrupts : The interrupt number
+  - pinctrl-0  : Standard Pinctrl phandle (see: pinctrl/pinctrl-bindings.txt)
+
+Optional properties:
+  - st,syscfg          : Phandle to boot-device system configuration registers
+  - st,boot-device-reg : Address of the aforementioned boot-device register(s)
+  - st,boot-device-spi : Expected boot-device value if booted via this device
+
+Example:
+	spifsm: spifsm@fe902000{
+	        compatible         = "st,spi-fsm";
+	        reg                =  <0xfe902000 0x1000>;
+	        reg-names          = "spi-fsm";
+	        pinctrl-0          = <&pinctrl_fsm>;
+		st,syscfg	   = <&syscfg_rear>;
+	        st,boot-device-reg = <0x958>;
+	        st,boot-device-spi = <0x1a>;
+		status = "okay";
+	};
+