dts: update to v4.16-rc1

Also includeded:

ARM: dts: am33xx: do not delete no longer existing clocks

Several clocks are removed from the am33xx dts files with v4.16-rc1.
Remove the corresponding /delete-node/ directives aswell to avoid
dtc breakage.

Also included:

ARM: dts: imx6qdl: SolidRun: Fix upstream include

Upstream dts file way renamed, so change include name accordingly.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

6 files changed, 138 insertions, 7 deletions

diff --git a/dts/Bindings/mtd/fsl-quadspi.txt b/dts/Bindings/mtd/fsl-quadspi.txt
index c34aa6f8a4..63d4d626fb 100644
--- a/dts/Bindings/mtd/fsl-quadspi.txt
+++ b/dts/Bindings/mtd/fsl-quadspi.txt
@@ -12,7 +12,7 @@ Required properties:
   - reg-names: Should contain the reg names "QuadSPI" and "QuadSPI-memory"
   - interrupts : Should contain the interrupt for the device
   - clocks : The clocks needed by the QuadSPI controller
-  - clock-names : the name of the clocks
+  - clock-names : Should contain the name of the clocks: "qspi_en" and "qspi".
 
 Optional properties:
   - fsl,qspi-has-second-chip: The controller has two buses, bus A and bus B.
diff --git a/dts/Bindings/mtd/gpmc-onenand.txt b/dts/Bindings/mtd/gpmc-onenand.txt
index b6e8bfd024..e9f01a963a 100644
--- a/dts/Bindings/mtd/gpmc-onenand.txt
+++ b/dts/Bindings/mtd/gpmc-onenand.txt
@@ -9,13 +9,14 @@ Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt
 
 Required properties:
 
+ - compatible:		"ti,omap2-onenand"
  - reg:			The CS line the peripheral is connected to
- - gpmc,device-width	Width of the ONENAND device connected to the GPMC
+ - gpmc,device-width:	Width of the ONENAND device connected to the GPMC
 			in bytes. Must be 1 or 2.
 
 Optional properties:
 
- - dma-channel:		DMA Channel index
+ - int-gpios:		GPIO specifier for the INT pin.
 
 For inline partition table parsing (optional):
 
@@ -35,6 +36,7 @@ Example for an OMAP3430 board:
 		#size-cells = <1>;
 
 		onenand@0 {
+			compatible = "ti,omap2-onenand";
 			reg = <0 0 0>; /* CS0, offset 0 */
 			gpmc,device-width = <2>;
 
diff --git a/dts/Bindings/mtd/lpc32xx-mlc.txt b/dts/Bindings/mtd/lpc32xx-mlc.txt
index d0a37252eb..6d60bc3063 100644
--- a/dts/Bindings/mtd/lpc32xx-mlc.txt
+++ b/dts/Bindings/mtd/lpc32xx-mlc.txt
@@ -23,7 +23,7 @@ Optional subnodes:
 
 Example:
 
-	mlc: flash@200A8000 {
+	mlc: flash@200a8000 {
 		compatible = "nxp,lpc3220-mlc";
 		reg = <0x200A8000 0x11000>;
 		interrupts = <11 0>;
diff --git a/dts/Bindings/mtd/marvell-nand.txt b/dts/Bindings/mtd/marvell-nand.txt
new file mode 100644
index 0000000000..c08fb477b3
--- /dev/null
+++ b/dts/Bindings/mtd/marvell-nand.txt
@@ -0,0 +1,123 @@
+Marvell NAND Flash Controller (NFC)
+
+Required properties:
+- compatible: can be one of the following:
+    * "marvell,armada-8k-nand-controller"
+    * "marvell,armada370-nand-controller"
+    * "marvell,pxa3xx-nand-controller"
+    * "marvell,armada-8k-nand" (deprecated)
+    * "marvell,armada370-nand" (deprecated)
+    * "marvell,pxa3xx-nand" (deprecated)
+  Compatibles marked deprecated support only the old bindings described
+  at the bottom.
+- reg: NAND flash controller memory area.
+- #address-cells: shall be set to 1. Encode the NAND CS.
+- #size-cells: shall be set to 0.
+- interrupts: shall define the NAND controller interrupt.
+- clocks: shall reference the NAND controller clock.
+- marvell,system-controller: Set to retrieve the syscon node that handles
+  NAND controller related registers (only required with the
+  "marvell,armada-8k-nand[-controller]" compatibles).
+
+Optional properties:
+- label: see partition.txt. New platforms shall omit this property.
+- dmas: shall reference DMA channel associated to the NAND controller.
+  This property is only used with "marvell,pxa3xx-nand[-controller]"
+  compatible strings.
+- dma-names: shall be "rxtx".
+  This property is only used with "marvell,pxa3xx-nand[-controller]"
+  compatible strings.
+
+Optional children nodes:
+Children nodes represent the available NAND chips.
+
+Required properties:
+- reg: shall contain the native Chip Select ids (0-3).
+- nand-rb: see nand.txt (0-1).
+
+Optional properties:
+- marvell,nand-keep-config: orders the driver not to take the timings
+  from the core and leaving them completely untouched. Bootloader
+  timings will then be used.
+- label: MTD name.
+- nand-on-flash-bbt: see nand.txt.
+- nand-ecc-mode: see nand.txt. Will use hardware ECC if not specified.
+- nand-ecc-algo: see nand.txt. This property is essentially useful when
+  not using hardware ECC. Howerver, it may be added when using hardware
+  ECC for clarification but will be ignored by the driver because ECC
+  mode is chosen depending on the page size and the strength required by
+  the NAND chip. This value may be overwritten with nand-ecc-strength
+  property.
+- nand-ecc-strength: see nand.txt.
+- nand-ecc-step-size: see nand.txt. Marvell's NAND flash controller does
+  use fixed strength (1-bit for Hamming, 16-bit for BCH), so the actual
+  step size will shrink or grow in order to fit the required strength.
+  Step sizes are not completely random for all and follow certain
+  patterns described in AN-379, "Marvell SoC NFC ECC".
+
+See Documentation/devicetree/bindings/mtd/nand.txt for more details on
+generic bindings.
+
+
+Example:
+nand_controller: nand-controller@d0000 {
+	compatible = "marvell,armada370-nand-controller";
+	reg = <0xd0000 0x54>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+	clocks = <&coredivclk 0>;
+
+	nand@0 {
+		reg = <0>;
+		label = "main-storage";
+		nand-rb = <0>;
+		nand-ecc-mode = "hw";
+		marvell,nand-keep-config;
+		nand-on-flash-bbt;
+		nand-ecc-strength = <4>;
+		nand-ecc-step-size = <512>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "Rootfs";
+				reg = <0x00000000 0x40000000>;
+			};
+		};
+	};
+};
+
+
+Note on legacy bindings: One can find, in not-updated device trees,
+bindings slightly different than described above with other properties
+described below as well as the partitions node at the root of a so
+called "nand" node (without clear controller/chip separation).
+
+Legacy properties:
+- marvell,nand-enable-arbiter: To enable the arbiter, all boards blindly
+  used it, this bit was set by the bootloader for many boards and even if
+  it is marked reserved in several datasheets, it might be needed to set
+  it (otherwise it is harmless) so whether or not this property is set,
+  the bit is selected by the driver.
+- num-cs: Number of chip-select lines to use, all boards blindly set 1
+  to this and for a reason, other values would have failed. The value of
+  this property is ignored.
+
+Example:
+
+	nand0: nand@43100000 {
+		compatible = "marvell,pxa3xx-nand";
+		reg = <0x43100000 90>;
+		interrupts = <45>;
+		dmas = <&pdma 97 0>;
+		dma-names = "rxtx";
+		#address-cells = <1>;
+		marvell,nand-keep-config;
+		marvell,nand-enable-arbiter;
+		num-cs = <1>;
+		/* Partitions (optional) */
+       };
diff --git a/dts/Bindings/mtd/mtk-nand.txt b/dts/Bindings/mtd/mtk-nand.txt
index 0431841de7..1c88526ded 100644
--- a/dts/Bindings/mtd/mtk-nand.txt
+++ b/dts/Bindings/mtd/mtk-nand.txt
@@ -12,8 +12,10 @@ tree nodes.
 
 The first part of NFC is NAND Controller Interface (NFI) HW.
 Required NFI properties:
-- compatible:			Should be one of "mediatek,mt2701-nfc",
-				"mediatek,mt2712-nfc".
+- compatible:			Should be one of
+				"mediatek,mt2701-nfc",
+				"mediatek,mt2712-nfc",
+				"mediatek,mt7622-nfc".
 - reg:				Base physical address and size of NFI.
 - interrupts:			Interrupts of NFI.
 - clocks:			NFI required clocks.
@@ -142,7 +144,10 @@ Example:
 ==============
 
 Required BCH properties:
-- compatible:	Should be one of "mediatek,mt2701-ecc", "mediatek,mt2712-ecc".
+- compatible:	Should be one of
+		"mediatek,mt2701-ecc",
+		"mediatek,mt2712-ecc",
+		"mediatek,mt7622-ecc".
 - reg:		Base physical address and size of ECC.
 - interrupts:	Interrupts of ECC.
 - clocks:	ECC required clocks.
diff --git a/dts/Bindings/mtd/nand.txt b/dts/Bindings/mtd/nand.txt
index 133f381371..8bb11d8094 100644
--- a/dts/Bindings/mtd/nand.txt
+++ b/dts/Bindings/mtd/nand.txt
@@ -43,6 +43,7 @@ Optional NAND chip properties:
 		     This is particularly useful when only the in-band area is
 		     used by the upper layers, and you want to make your NAND
 		     as reliable as possible.
+- nand-rb: shall contain the native Ready/Busy ids.
 
 The ECC strength and ECC step size properties define the correction capability
 of a controller. Together, they say a controller can correct "{strength} bit