Add devicetree source files as of Linux-3.15-rc2

This adds the Linux dts files to barebox. The dts files are
generated from Ian Campbells device-tree-rebasing.git:

git://xenbits.xen.org/people/ianc/device-tree-rebasing.git

The dts are found in dts/ in the barebox repository and
will be updated from upstream regularly, probably for each upstream
-rc.

To keep the synchronization with upstream easy no changes to
the original files are allowed under dts/. Instead changes to
upstream dts files will be done using overlays in arch/$ARCH/dts/.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

1 files changed, 97 insertions, 0 deletions

diff --git a/dts/Bindings/net/gpmc-eth.txt b/dts/Bindings/net/gpmc-eth.txt
new file mode 100644
index 0000000000..ace4a64b36
--- /dev/null
+++ b/dts/Bindings/net/gpmc-eth.txt
@@ -0,0 +1,97 @@
+Device tree bindings for Ethernet chip connected to TI GPMC
+
+Besides being used to interface with external memory devices, the
+General-Purpose Memory Controller can be used to connect Pseudo-SRAM devices
+such as ethernet controllers to processors using the TI GPMC as a data bus.
+
+Ethernet controllers connected to TI GPMC are represented as child nodes of
+the GPMC controller with an "ethernet" name.
+
+All timing relevant properties as well as generic GPMC child properties are
+explained in a separate documents. Please refer to
+Documentation/devicetree/bindings/bus/ti-gpmc.txt
+
+For the properties relevant to the ethernet controller connected to the GPMC
+refer to the binding documentation of the device. For example, the documentation
+for the SMSC 911x is Documentation/devicetree/bindings/net/smsc911x.txt
+
+Child nodes need to specify the GPMC bus address width using the "bank-width"
+property but is possible that an ethernet controller also has a property to
+specify the I/O registers address width. Even when the GPMC has a maximum 16-bit
+address width, it supports devices with 32-bit word registers.
+For example with an SMSC LAN911x/912x controller connected to the TI GPMC on an
+OMAP2+ board, "bank-width = <2>;" and "reg-io-width = <4>;".
+
+Required properties:
+- bank-width: 		Address width of the device in bytes. GPMC supports 8-bit
+			and 16-bit devices and so must be either 1 or 2 bytes.
+- compatible:		Compatible string property for the ethernet child device.
+- gpmc,cs-on-ns:	Chip-select assertion time
+- gpmc,cs-rd-off-ns:	Chip-select de-assertion time for reads
+- gpmc,cs-wr-off-ns:	Chip-select de-assertion time for writes
+- gpmc,oe-on-ns:	Output-enable assertion time
+- gpmc,oe-off-ns:	Output-enable de-assertion time
+- gpmc,we-on-ns:	Write-enable assertion time
+- gpmc,we-off-ns:	Write-enable de-assertion time
+- gpmc,access-ns:	Start cycle to first data capture (read access)
+- gpmc,rd-cycle-ns:	Total read cycle time
+- gpmc,wr-cycle-ns:	Total write cycle time
+- reg:			Chip-select, base address (relative to chip-select)
+			and size of the memory mapped for the device.
+			Note that base address will be typically 0 as this
+			is the start of the chip-select.
+
+Optional properties:
+- gpmc,XXX		Additional GPMC timings and settings parameters. See
+			Documentation/devicetree/bindings/bus/ti-gpmc.txt
+
+Example:
+
+gpmc: gpmc@6e000000 {
+	compatible = "ti,omap3430-gpmc";
+	ti,hwmods = "gpmc";
+	reg = <0x6e000000 0x1000>;
+	interrupts = <20>;
+	gpmc,num-cs = <8>;
+	gpmc,num-waitpins = <4>;
+	#address-cells = <2>;
+	#size-cells = <1>;
+
+	ranges = <5 0 0x2c000000 0x1000000>;
+
+	ethernet@5,0 {
+		compatible = "smsc,lan9221", "smsc,lan9115";
+		reg = <5 0 0xff>;
+		bank-width = <2>;
+
+		gpmc,mux-add-data;
+		gpmc,cs-on-ns = <0>;
+		gpmc,cs-rd-off-ns = <186>;
+		gpmc,cs-wr-off-ns = <186>;
+		gpmc,adv-on-ns = <12>;
+		gpmc,adv-rd-off-ns = <48>;
+		gpmc,adv-wr-off-ns = <48>;
+		gpmc,oe-on-ns = <54>;
+		gpmc,oe-off-ns = <168>;
+		gpmc,we-on-ns = <54>;
+		gpmc,we-off-ns = <168>;
+		gpmc,rd-cycle-ns = <186>;
+		gpmc,wr-cycle-ns = <186>;
+		gpmc,access-ns = <114>;
+		gpmc,page-burst-access-ns = <6>;
+		gpmc,bus-turnaround-ns = <12>;
+		gpmc,cycle2cycle-delay-ns = <18>;
+		gpmc,wr-data-mux-bus-ns = <90>;
+		gpmc,wr-access-ns = <186>;
+		gpmc,cycle2cycle-samecsen;
+		gpmc,cycle2cycle-diffcsen;
+
+		interrupt-parent = <&gpio6>;
+		interrupts = <16>;
+		vmmc-supply = <&vddvario>;
+		vmmc_aux-supply = <&vdd33a>;
+		reg-io-width = <4>;
+
+		smsc,save-mac-address;
+	};
+};