dts: update to v3.18-rc1

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

19 files changed, 486 insertions, 47 deletions

diff --git a/dts/Bindings/net/apm-xgene-enet.txt b/dts/Bindings/net/apm-xgene-enet.txt
index ebcad25efd..cfcc52705e 100644
--- a/dts/Bindings/net/apm-xgene-enet.txt
+++ b/dts/Bindings/net/apm-xgene-enet.txt
@@ -3,7 +3,7 @@ APM X-Gene SoC Ethernet nodes
 Ethernet nodes are defined to describe on-chip ethernet interfaces in
 APM X-Gene SoC.
 
-Required properties:
+Required properties for all the ethernet interfaces:
 - compatible: Should be "apm,xgene-enet"
 - reg: Address and length of the register set for the device. It contains the
   information of registers in the same order as described by reg-names
@@ -15,6 +15,8 @@ Required properties:
 - clocks: Reference to the clock entry.
 - local-mac-address: MAC address assigned to this device
 - phy-connection-type: Interface type between ethernet device and PHY device
+
+Required properties for ethernet interfaces that have external PHY:
 - phy-handle: Reference to a PHY node connected to this device
 
 - mdio: Device tree subnode with the following required properties:
diff --git a/dts/Bindings/net/broadcom-mdio-unimac.txt b/dts/Bindings/net/broadcom-mdio-unimac.txt
new file mode 100644
index 0000000000..ab0bb4247d
--- /dev/null
+++ b/dts/Bindings/net/broadcom-mdio-unimac.txt
@@ -0,0 +1,39 @@
+* Broadcom UniMAC MDIO bus controller
+
+Required properties:
+- compatible: should one from "brcm,genet-mdio-v1", "brcm,genet-mdio-v2",
+  "brcm,genet-mdio-v3", "brcm,genet-mdio-v4" or "brcm,unimac-mdio"
+- reg: address and length of the regsiter set for the device, first one is the
+  base register, and the second one is optional and for indirect accesses to
+  larger than 16-bits MDIO transactions
+- reg-names: name(s) of the register must be "mdio" and optional "mdio_indir_rw"
+- #size-cells: must be 1
+- #address-cells: must be 0
+
+Optional properties:
+- interrupts: must be one if the interrupt is shared with the Ethernet MAC or
+  Ethernet switch this MDIO block is integrated from, or must be two, if there
+  are two separate interrupts, first one must be "mdio done" and second must be
+  for "mdio error"
+- interrupt-names: must be "mdio_done_error" when there is a share interrupt fed
+  to this hardware block, or must be "mdio_done" for the first interrupt and
+  "mdio_error" for the second when there are separate interrupts
+
+Child nodes of this MDIO bus controller node are standard Ethernet PHY device
+nodes as described in Documentation/devicetree/bindings/net/phy.txt
+
+Example:
+
+mdio@403c0 {
+	compatible = "brcm,unimac-mdio";
+	reg = <0x403c0 0x8 0x40300 0x18>;
+	reg-names = "mdio", "mdio_indir_rw";
+	#size-cells = <1>;
+	#address-cells = <0>;
+
+	...
+	phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
diff --git a/dts/Bindings/net/broadcom-sf2.txt b/dts/Bindings/net/broadcom-sf2.txt
new file mode 100644
index 0000000000..30d487597e
--- /dev/null
+++ b/dts/Bindings/net/broadcom-sf2.txt
@@ -0,0 +1,78 @@
+* Broadcom Starfighter 2 integrated swich
+
+Required properties:
+
+- compatible: should be "brcm,bcm7445-switch-v4.0"
+- reg: addresses and length of the register sets for the device, must be 6
+  pairs of register addresses and lengths
+- interrupts: interrupts for the devices, must be two interrupts
+- dsa,mii-bus: phandle to the MDIO bus controller, see dsa/dsa.txt
+- dsa,ethernet: phandle to the CPU network interface controller, see dsa/dsa.txt
+- #size-cells: must be 0
+- #address-cells: must be 2, see dsa/dsa.txt
+
+Subnodes:
+
+The integrated switch subnode should be specified according to the binding
+described in dsa/dsa.txt.
+
+Optional properties:
+
+- reg-names: litteral names for the device base register addresses, when present
+  must be: "core", "reg", "intrl2_0", "intrl2_1", "fcb", "acb"
+
+- interrupt-names: litternal names for the device interrupt lines, when present
+  must be: "switch_0" and "switch_1"
+
+- brcm,num-gphy: specify the maximum number of integrated gigabit PHYs in the
+  switch
+
+- brcm,num-rgmii-ports: specify the maximum number of RGMII interfaces supported
+  by the switch
+
+- brcm,fcb-pause-override: boolean property, if present indicates that the switch
+  supports Failover Control Block pause override capability
+
+- brcm,acb-packets-inflight: boolean property, if present indicates that the switch
+  Admission Control Block supports reporting the number of packets in-flight in a
+  switch queue
+
+Example:
+
+switch_top@f0b00000 {
+	compatible = "simple-bus";
+	#size-cells = <1>;
+	#address-cells = <1>;
+	ranges = <0 0xf0b00000 0x40804>;
+
+	ethernet_switch@0 {
+		compatible = "brcm,bcm7445-switch-v4.0";
+		#size-cells = <0>;
+		#address-cells = <2>;
+		reg = <0x0 0x40000
+			0x40000 0x110
+			0x40340 0x30
+			0x40380 0x30
+			0x40400 0x34
+			0x40600 0x208>;
+		interrupts = <0 0x18 0
+				0 0x19 0>;
+		brcm,num-gphy = <1>;
+		brcm,num-rgmii-ports = <2>;
+		brcm,fcb-pause-override;
+		brcm,acb-packets-inflight;
+
+		...
+		switch@0 {
+			reg = <0 0>;
+			#size-cells = <0>;
+			#address-cells <1>;
+
+			port@0 {
+				label = "gphy";
+				reg = <0>;
+			};
+			...
+		};
+	};
+};
diff --git a/dts/Bindings/net/can/m_can.txt b/dts/Bindings/net/can/m_can.txt
new file mode 100644
index 0000000000..9e331777c2
--- /dev/null
+++ b/dts/Bindings/net/can/m_can.txt
@@ -0,0 +1,67 @@
+Bosch MCAN controller Device Tree Bindings
+-------------------------------------------------
+
+Required properties:
+- compatible		: Should be "bosch,m_can" for M_CAN controllers
+- reg			: physical base address and size of the M_CAN
+			  registers map and Message RAM
+- reg-names		: Should be "m_can" and "message_ram"
+- interrupts		: Should be the interrupt number of M_CAN interrupt
+			  line 0 and line 1, could be same if sharing
+			  the same interrupt.
+- interrupt-names	: Should contain "int0" and "int1"
+- clocks		: Clocks used by controller, should be host clock
+			  and CAN clock.
+- clock-names		: Should contain "hclk" and "cclk"
+- pinctrl-<n>		: Pinctrl states as described in bindings/pinctrl/pinctrl-bindings.txt
+- pinctrl-names 	: Names corresponding to the numbered pinctrl states
+- bosch,mram-cfg	: Message RAM configuration data.
+			  Multiple M_CAN instances can share the same Message
+			  RAM and each element(e.g Rx FIFO or Tx Buffer and etc)
+			  number in Message RAM is also configurable,
+			  so this property is telling driver how the shared or
+			  private Message RAM are used by this M_CAN controller.
+
+			  The format should be as follows:
+			  <offset sidf_elems xidf_elems rxf0_elems rxf1_elems
+			   rxb_elems txe_elems txb_elems>
+			  The 'offset' is an address offset of the Message RAM
+			  where the following elements start from. This is
+			  usually set to 0x0 if you're using a private Message
+			  RAM. The remain cells are used to specify how many
+			  elements are used for each FIFO/Buffer.
+
+			  M_CAN includes the following elements according to user manual:
+			  11-bit Filter	0-128 elements / 0-128 words
+			  29-bit Filter	0-64 elements / 0-128 words
+			  Rx FIFO 0	0-64 elements / 0-1152 words
+			  Rx FIFO 1	0-64 elements / 0-1152 words
+			  Rx Buffers	0-64 elements / 0-1152 words
+			  Tx Event FIFO	0-32 elements / 0-64 words
+			  Tx Buffers	0-32 elements / 0-576 words
+
+			  Please refer to 2.4.1 Message RAM Configuration in
+			  Bosch M_CAN user manual for details.
+
+Example:
+SoC dtsi:
+m_can1: can@020e8000 {
+	compatible = "bosch,m_can";
+	reg = <0x020e8000 0x4000>, <0x02298000 0x4000>;
+	reg-names = "m_can", "message_ram";
+	interrupts = <0 114 0x04>,
+		     <0 114 0x04>;
+	interrupt-names = "int0", "int1";
+	clocks = <&clks IMX6SX_CLK_CANFD>,
+		 <&clks IMX6SX_CLK_CANFD>;
+	clock-names = "hclk", "cclk";
+	bosch,mram-cfg = <0x0 0 0 32 0 0 0 1>;
+	status = "disabled";
+};
+
+Board dts:
+&m_can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_m_can1>;
+	status = "enabled";
+};
diff --git a/dts/Bindings/net/can/rcar_can.txt b/dts/Bindings/net/can/rcar_can.txt
new file mode 100644
index 0000000000..002d8440bf
--- /dev/null
+++ b/dts/Bindings/net/can/rcar_can.txt
@@ -0,0 +1,43 @@
+Renesas R-Car CAN controller Device Tree Bindings
+-------------------------------------------------
+
+Required properties:
+- compatible: "renesas,can-r8a7778" if CAN controller is a part of R8A7778 SoC.
+	      "renesas,can-r8a7779" if CAN controller is a part of R8A7779 SoC.
+	      "renesas,can-r8a7790" if CAN controller is a part of R8A7790 SoC.
+	      "renesas,can-r8a7791" if CAN controller is a part of R8A7791 SoC.
+- reg: physical base address and size of the R-Car CAN register map.
+- interrupts: interrupt specifier for the sole interrupt.
+- clocks: phandles and clock specifiers for 3 CAN clock inputs.
+- clock-names: 3 clock input name strings: "clkp1", "clkp2", "can_clk".
+- pinctrl-0: pin control group to be used for this controller.
+- pinctrl-names: must be "default".
+
+Optional properties:
+- renesas,can-clock-select: R-Car CAN Clock Source Select. Valid values are:
+			    <0x0> (default) : Peripheral clock (clkp1)
+			    <0x1> : Peripheral clock (clkp2)
+			    <0x3> : Externally input clock
+
+Example
+-------
+
+SoC common .dtsi file:
+
+	can0: can@e6e80000 {
+		compatible = "renesas,can-r8a7791";
+		reg = <0 0xe6e80000 0 0x1000>;
+		interrupts = <0 186 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&mstp9_clks R8A7791_CLK_RCAN0>,
+			 <&cpg_clocks R8A7791_CLK_RCAN>, <&can_clk>;
+		clock-names = "clkp1", "clkp2", "can_clk";
+		status = "disabled";
+	};
+
+Board specific .dts file:
+
+&can0 {
+	pinctrl-0 = <&can0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
diff --git a/dts/Bindings/net/cpsw.txt b/dts/Bindings/net/cpsw.txt
index ae2b8b7f9c..33fe8462ed 100644
--- a/dts/Bindings/net/cpsw.txt
+++ b/dts/Bindings/net/cpsw.txt
@@ -24,15 +24,17 @@ Optional properties:
 - ti,hwmods		: Must be "cpgmac0"
 - no_bd_ram		: Must be 0 or 1
 - dual_emac		: Specifies Switch to act as Dual EMAC
+- syscon		: Phandle to the system control device node, which is
+			  the control module device of the am33x
 
 Slave Properties:
 Required properties:
 - phy_id		: Specifies slave phy id
 - phy-mode		: See ethernet.txt file in the same directory
-- mac-address		: See ethernet.txt file in the same directory
 
 Optional properties:
 - dual_emac_res_vlan	: Specifies VID to be used to segregate the ports
+- mac-address		: See ethernet.txt file in the same directory
 
 Note: "ti,hwmods" field is used to fetch the base address and irq
 resources from TI, omap hwmod data base during device registration.
@@ -57,6 +59,7 @@ Examples:
 		active_slave = <0>;
 		cpts_clock_mult = <0x80000000>;
 		cpts_clock_shift = <29>;
+		syscon = <&cm>;
 		cpsw_emac0: slave@0 {
 			phy_id = <&davinci_mdio>, <0>;
 			phy-mode = "rgmii-txid";
@@ -85,6 +88,7 @@ Examples:
 		active_slave = <0>;
 		cpts_clock_mult = <0x80000000>;
 		cpts_clock_shift = <29>;
+		syscon = <&cm>;
 		cpsw_emac0: slave@0 {
 			phy_id = <&davinci_mdio>, <0>;
 			phy-mode = "rgmii-txid";
diff --git a/dts/Bindings/net/dsa/dsa.txt b/dts/Bindings/net/dsa/dsa.txt
index 49f4f7ae3f..a62c889aaf 100644
--- a/dts/Bindings/net/dsa/dsa.txt
+++ b/dts/Bindings/net/dsa/dsa.txt
@@ -39,6 +39,22 @@ Optionnal property:
 			  This property is only used when switches are being
 			  chained/cascaded together.
 
+- phy-handle		: Phandle to a PHY on an external MDIO bus, not the
+			  switch internal one. See
+			  Documentation/devicetree/bindings/net/ethernet.txt
+			  for details.
+
+- phy-mode		: String representing the connection to the designated
+			  PHY node specified by the 'phy-handle' property. See
+			  Documentation/devicetree/bindings/net/ethernet.txt
+			  for details.
+
+Optional subnodes:
+- fixed-link		: Fixed-link subnode describing a link to a non-MDIO
+			  managed entity. See
+			  Documentation/devicetree/bindings/net/fixed-link.txt
+			  for details.
+
 Example:
 
 	dsa@0 {
@@ -58,6 +74,7 @@ Example:
 			port@0 {
 				reg = <0>;
 				label = "lan1";
+				phy-handle = <&phy0>;
 			};
 
 			port@1 {
diff --git a/dts/Bindings/net/emac_rockchip.txt b/dts/Bindings/net/emac_rockchip.txt
new file mode 100644
index 0000000000..8dc1c79fef
--- /dev/null
+++ b/dts/Bindings/net/emac_rockchip.txt
@@ -0,0 +1,50 @@
+* ARC EMAC 10/100 Ethernet platform driver for Rockchip Rk3066/RK3188 SoCs
+
+Required properties:
+- compatible: Should be "rockchip,rk3066-emac" or "rockchip,rk3188-emac"
+  according to the target SoC.
+- reg: Address and length of the register set for the device
+- interrupts: Should contain the EMAC interrupts
+- rockchip,grf: phandle to the syscon grf used to control speed and mode
+  for emac.
+- phy: see ethernet.txt file in the same directory.
+- phy-mode: see ethernet.txt file in the same directory.
+
+Optional properties:
+- phy-supply: phandle to a regulator if the PHY needs one
+
+Clock handling:
+- clocks: Must contain an entry for each entry in clock-names.
+- clock-names: Shall be "hclk" for the host clock needed to calculate and set
+  polling period of EMAC and "macref" for the reference clock needed to transfer
+  data to and from the phy.
+
+Child nodes of the driver are the individual PHY devices connected to the
+MDIO bus. They must have a "reg" property given the PHY address on the MDIO bus.
+
+Examples:
+
+ethernet@10204000 {
+	compatible = "rockchip,rk3188-emac";
+	reg = <0xc0fc2000 0x3c>;
+	interrupts = <6>;
+	mac-address = [ 00 11 22 33 44 55 ];
+
+	clocks = <&cru HCLK_EMAC>, <&cru SCLK_MAC>;
+	clock-names = "hclk", "macref";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&emac_xfer>, <&emac_mdio>, <&phy_int>;
+
+	rockchip,grf = <&grf>;
+
+	phy = <&phy0>;
+	phy-mode = "rmii";
+	phy-supply = <&vcc_rmii>;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+	phy0: ethernet-phy@0 {
+	      reg = <1>;
+	};
+};
diff --git a/dts/Bindings/net/fsl-fec.txt b/dts/Bindings/net/fsl-fec.txt
index 8a2c7b55ec..0c8775c457 100644
--- a/dts/Bindings/net/fsl-fec.txt
+++ b/dts/Bindings/net/fsl-fec.txt
@@ -16,6 +16,12 @@ Optional properties:
 - phy-handle : phandle to the PHY device connected to this device.
 - fixed-link : Assume a fixed link. See fixed-link.txt in the same directory.
   Use instead of phy-handle.
+- fsl,num-tx-queues : The property is valid for enet-avb IP, which supports
+  hw multi queues. Should specify the tx queue number, otherwise set tx queue
+  number to 1.
+- fsl,num-rx-queues : The property is valid for enet-avb IP, which supports
+  hw multi queues. Should specify the rx queue number, otherwise set rx queue
+  number to 1.
 
 Optional subnodes:
 - mdio : specifies the mdio bus in the FEC, used as a container for phy nodes
diff --git a/dts/Bindings/net/marvell-pxa168.txt b/dts/Bindings/net/marvell-pxa168.txt
new file mode 100644
index 0000000000..845a148a34
--- /dev/null
+++ b/dts/Bindings/net/marvell-pxa168.txt
@@ -0,0 +1,36 @@
+* Marvell PXA168 Ethernet Controller
+
+Required properties:
+- compatible: should be "marvell,pxa168-eth".
+- reg: address and length of the register set for the device.
+- interrupts: interrupt for the device.
+- clocks: pointer to the clock for the device.
+
+Optional properties:
+- port-id: Ethernet port number. Should be '0','1' or '2'.
+- #address-cells: must be 1 when using sub-nodes.
+- #size-cells: must be 0 when using sub-nodes.
+- phy-handle: see ethernet.txt file in the same directory.
+- local-mac-address: see ethernet.txt file in the same directory.
+
+Sub-nodes:
+Each PHY can be represented as a sub-node. This is not mandatory.
+
+Sub-nodes required properties:
+- reg: the MDIO address of the PHY.
+
+Example:
+
+	eth0: ethernet@f7b90000 {
+		compatible = "marvell,pxa168-eth";
+		reg = <0xf7b90000 0x10000>;
+		clocks = <&chip CLKID_GETH0>;
+		interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		phy-handle = <&ethphy0>;
+
+		ethphy0: ethernet-phy@0 {
+			reg = <0>;
+		};
+	};
diff --git a/dts/Bindings/net/meson-dwmac.txt b/dts/Bindings/net/meson-dwmac.txt
new file mode 100644
index 0000000000..ec633d74a8
--- /dev/null
+++ b/dts/Bindings/net/meson-dwmac.txt
@@ -0,0 +1,25 @@
+* Amlogic Meson DWMAC Ethernet controller
+
+The device inherits all the properties of the dwmac/stmmac devices
+described in the file net/stmmac.txt with the following changes.
+
+Required properties:
+
+- compatible: should be "amlogic,meson6-dwmac" along with "snps,dwmac"
+	      and any applicable more detailed version number
+	      described in net/stmmac.txt
+
+- reg: should contain a register range for the dwmac controller and
+       another one for the Amlogic specific configuration
+
+Example:
+
+	ethmac: ethernet@c9410000 {
+		compatible = "amlogic,meson6-dwmac", "snps,dwmac";
+		reg = <0xc9410000 0x10000
+		       0xc1108108 0x4>;
+		interrupts = <0 8 1>;
+		interrupt-names = "macirq";
+		clocks = <&clk81>;
+		clock-names = "stmmaceth";
+	}
diff --git a/dts/Bindings/net/micrel.txt b/dts/Bindings/net/micrel.txt
index 98a3e61f9e..e1d99b95c4 100644
--- a/dts/Bindings/net/micrel.txt
+++ b/dts/Bindings/net/micrel.txt
@@ -16,3 +16,9 @@ Optional properties:
 	      KSZ8051: register 0x1f, bits 5..4
 
               See the respective PHY datasheet for the mode values.
+
+ - clocks, clock-names: contains clocks according to the common clock bindings.
+
+              supported clocks:
+	      - KSZ8021, KSZ8031: "rmii-ref": The RMII refence input clock. Used
+		to determine the XI input clock.
diff --git a/dts/Bindings/net/nfc/st21nfcb.txt b/dts/Bindings/net/nfc/st21nfcb.txt
index 3b58ae4803..9005608cbb 100644
--- a/dts/Bindings/net/nfc/st21nfcb.txt
+++ b/dts/Bindings/net/nfc/st21nfcb.txt
@@ -26,7 +26,7 @@ Example (for ARM-based BeagleBoard xM with ST21NFCB on I2C2):
 		clock-frequency = <400000>;
 
 		interrupt-parent = <&gpio5>;
-		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+		interrupts = <2 IRQ_TYPE_LEVEL_HIGH>;
 
 		reset-gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>;
 	};
diff --git a/dts/Bindings/net/nfc/trf7970a.txt b/dts/Bindings/net/nfc/trf7970a.txt
index 1e43613368..7c89ca290c 100644
--- a/dts/Bindings/net/nfc/trf7970a.txt
+++ b/dts/Bindings/net/nfc/trf7970a.txt
@@ -13,6 +13,11 @@ Optional SoC Specific Properties:
 - pinctrl-names: Contains only one value - "default".
 - pintctrl-0: Specifies the pin control groups used for this controller.
 - autosuspend-delay: Specify autosuspend delay in milliseconds.
+- vin-voltage-override: Specify voltage of VIN pin in microvolts.
+- irq-status-read-quirk: Specify that the trf7970a being used has the
+  "IRQ Status Read" erratum.
+- en2-rf-quirk: Specify that the trf7970a being used has the "EN2 RF"
+  erratum.
 
 Example (for ARM-based BeagleBone with TRF7970A on SPI1):
 
@@ -30,7 +35,10 @@ Example (for ARM-based BeagleBone with TRF7970A on SPI1):
 		ti,enable-gpios = <&gpio2 2 GPIO_ACTIVE_LOW>,
 				  <&gpio2 5 GPIO_ACTIVE_LOW>;
 		vin-supply = <&ldo3_reg>;
+		vin-voltage-override = <5000000>;
 		autosuspend-delay = <30000>;
+		irq-status-read-quirk;
+		en2-rf-quirk;
 		status = "okay";
 	};
 };
diff --git a/dts/Bindings/net/qca-qca7000-spi.txt b/dts/Bindings/net/qca-qca7000-spi.txt
new file mode 100644
index 0000000000..c74989c0d8
--- /dev/null
+++ b/dts/Bindings/net/qca-qca7000-spi.txt
@@ -0,0 +1,47 @@
+* Qualcomm QCA7000 (Ethernet over SPI protocol)
+
+Note: The QCA7000 is useable as a SPI device. In this case it must be defined
+as a child of a SPI master in the device tree.
+
+Required properties:
+- compatible : Should be "qca,qca7000"
+- reg : Should specify the SPI chip select
+- interrupts : The first cell should specify the index of the source interrupt
+  and the second cell should specify the trigger type as rising edge
+- spi-cpha : Must be set
+- spi-cpol: Must be set
+
+Optional properties:
+- interrupt-parent : Specify the pHandle of the source interrupt
+- spi-max-frequency : Maximum frequency of the SPI bus the chip can operate at.
+  Numbers smaller than 1000000 or greater than 16000000 are invalid. Missing
+  the property will set the SPI frequency to 8000000 Hertz.
+- local-mac-address: 6 bytes, MAC address
+- qca,legacy-mode : Set the SPI data transfer of the QCA7000 to legacy mode.
+  In this mode the SPI master must toggle the chip select between each data
+  word. In burst mode these gaps aren't necessary, which is faster.
+  This setting depends on how the QCA7000 is setup via GPIO pin strapping.
+  If the property is missing the driver defaults to burst mode.
+
+Example:
+
+/* Freescale i.MX28 SPI master*/
+ssp2: spi@80014000 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	compatible = "fsl,imx28-spi";
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2_pins_a>;
+	status = "okay";
+
+	qca7000: ethernet@0 {
+		compatible = "qca,qca7000";
+		reg = <0x0>;
+		interrupt-parent = <&gpio3>;      /* GPIO Bank 3 */
+		interrupts = <25 0x1>;            /* Index: 25, rising edge */
+		spi-cpha;                         /* SPI mode: CPHA=1 */
+		spi-cpol;                         /* SPI mode: CPOL=1 */
+		spi-max-frequency = <8000000>;    /* freq: 8 MHz */
+		local-mac-address = [ A0 B0 C0 D0 E0 F0 ];
+	};
+};
diff --git a/dts/Bindings/net/samsung-sxgbe.txt b/dts/Bindings/net/samsung-sxgbe.txt
index 989f6c95cf..888c250197 100644
--- a/dts/Bindings/net/samsung-sxgbe.txt
+++ b/dts/Bindings/net/samsung-sxgbe.txt
@@ -17,7 +17,7 @@ Required properties:
 - samsung,pbl: Integer, Programmable Burst Length.
   Supported values are 1, 2, 4, 8, 16, or 32.
 - samsung,burst-map: Integer, Program the possible bursts supported by sxgbe
-  This is an interger and represents allowable DMA bursts when fixed burst.
+  This is an integer and represents allowable DMA bursts when fixed burst.
   Allowable range is 0x01-0x3F. When this field is set fixed burst is enabled.
   When fixed length is needed for burst mode, it can be set within allowable
   range.
diff --git a/dts/Bindings/net/socfpga-dwmac.txt b/dts/Bindings/net/socfpga-dwmac.txt
index 2a60cd3e8d..3a9d679516 100644
--- a/dts/Bindings/net/socfpga-dwmac.txt
+++ b/dts/Bindings/net/socfpga-dwmac.txt
@@ -12,6 +12,10 @@ Required properties:
  - altr,sysmgr-syscon : Should be the phandle to the system manager node that
    encompasses the glue register, the register offset, and the register shift.
 
+Optional properties:
+altr,emac-splitter: Should be the phandle to the emac splitter soft IP node if
+		DWMAC controller is connected emac splitter.
+
 Example:
 
 gmac0: ethernet@ff700000 {
diff --git a/dts/Bindings/net/sti-dwmac.txt b/dts/Bindings/net/sti-dwmac.txt
index 3dd3d0bf11..6762a6b5da 100644
--- a/dts/Bindings/net/sti-dwmac.txt
+++ b/dts/Bindings/net/sti-dwmac.txt
@@ -1,58 +1,65 @@
 STMicroelectronics SoC DWMAC glue layer controller
 
+This file documents differences between the core properties in
+Documentation/devicetree/bindings/net/stmmac.txt
+and what is needed on STi platforms to program the stmmac glue logic.
+
 The device node has following properties.
 
 Required properties:
- - compatible	: Can be "st,stih415-dwmac", "st,stih416-dwmac" or
-   "st,stid127-dwmac".
- - reg		: Offset of the glue configuration register map in system
+ - compatible	: Can be "st,stih415-dwmac", "st,stih416-dwmac",
+   "st,stih407-dwmac", "st,stid127-dwmac".
+ - reg : Offset of the glue configuration register map in system
    configuration regmap pointed by st,syscon property and size.
-
- - reg-names	: Should be "sti-ethconf".
-
- - st,syscon	: Should be phandle to system configuration node which
+ - st,syscon : Should be phandle to system configuration node which
    encompases this glue registers.
+ - st,gmac_en: this is to enable the gmac into a dedicated sysctl control
+   register available on STiH407 SoC.
+ - sti-ethconf: this is the gmac glue logic register to enable the GMAC,
+   select among the different modes and program the clk retiming.
+ - pinctrl-0: pin-control for all the MII mode supported.
 
- - st,tx-retime-src: On STi Parts for Giga bit speeds, 125Mhz clocks can be
-   wired up in from different sources. One via TXCLK pin and other via CLK_125
-   pin. This wiring is totally board dependent. However the retiming glue
-   logic should be configured accordingly. Possible values for this property
-
-	   "txclk" - if 125Mhz clock is wired up via txclk line.
-	   "clk_125" - if 125Mhz clock is wired up via clk_125 line.
-
-   This property is only valid for Giga bit setup( GMII, RGMII), and it is
-   un-used for non-giga bit (MII and RMII) setups. Also note that internal
-   clockgen can not generate stable 125Mhz clock.
-
- - st,ext-phyclk: This boolean property indicates who is generating the clock
-  for tx and rx. This property is only valid for RMII case where the clock can
-  be generated from the MAC or PHY.
-
- - clock-names: should be "sti-ethclk".
- - clocks: Should point to ethernet clockgen which can generate phyclk.
-
+Optional properties:
+ - resets : phandle pointing to the system reset controller with correct
+   reset line index for ethernet reset.
+ - st,ext-phyclk: valid only for RMII where PHY can generate 50MHz clock or
+   MAC can generate it.
+ - st,tx-retime-src: This specifies which clk is wired up to the mac for
+   retimeing tx lines. This is totally board dependent and can take one of the
+   posssible values from "txclk", "clk_125" or "clkgen".
+   If not passed, the internal clock will be used by default.
+ - sti-ethclk: this is the phy clock.
+ - sti-clkconf: this is an extra sysconfig register, available in new SoCs,
+   to program the clk retiming.
+ - st,gmac_en: to enable the GMAC, this only is present in some SoCs; e.g.
+   STiH407.
 
 Example:
 
-ethernet0: dwmac@fe810000 {
-	device_type 	= "network";
-	compatible	= "st,stih416-dwmac", "snps,dwmac", "snps,dwmac-3.710";
-	reg 		= <0xfe810000 0x8000>, <0x8bc 0x4>;
-	reg-names	= "stmmaceth", "sti-ethconf";
-	interrupts	= <0 133 0>, <0 134 0>, <0 135 0>;
-	interrupt-names	= "macirq", "eth_wake_irq", "eth_lpi";
-	phy-mode	= "mii";
+ethernet0: dwmac@9630000 {
+	device_type = "network";
+	status = "disabled";
+	compatible = "st,stih407-dwmac", "snps,dwmac", "snps,dwmac-3.710";
+	reg = <0x9630000 0x8000>, <0x80 0x4>;
+	reg-names = "stmmaceth", "sti-ethconf";
 
-	st,syscon	= <&syscfg_rear>;
+	st,syscon = <&syscfg_sbc_reg>;
+	st,gmac_en;
+	resets = <&softreset STIH407_ETH1_SOFTRESET>;
+	reset-names = "stmmaceth";
 
-	snps,pbl 	= <32>;
+	interrupts = <GIC_SPI 98 IRQ_TYPE_NONE>,
+		     <GIC_SPI 99 IRQ_TYPE_NONE>,
+		     <GIC_SPI 100 IRQ_TYPE_NONE>;
+	interrupt-names = "macirq", "eth_wake_irq", "eth_lpi";
+
+	snps,pbl = <32>;
 	snps,mixed-burst;
 
-	resets		= <&softreset STIH416_ETH0_SOFTRESET>;
-	reset-names	= "stmmaceth";
-	pinctrl-0	= <&pinctrl_mii0>;
-	pinctrl-names 	= "default";
-	clocks		= <&CLK_S_GMAC0_PHY>;
-	clock-names	= "stmmaceth";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii1>;
+
+	clock-names = "stmmaceth", "sti-ethclk";
+	clocks = <&CLK_S_C0_FLEXGEN CLK_EXT2F_A9>,
+		 <&CLK_S_C0_FLEXGEN CLK_ETH_PHY>;
 };
diff --git a/dts/Bindings/net/stmmac.txt b/dts/Bindings/net/stmmac.txt
index e45ac3f926..c41afd963e 100644
--- a/dts/Bindings/net/stmmac.txt
+++ b/dts/Bindings/net/stmmac.txt
@@ -58,5 +58,5 @@ Examples:
 		snps,multicast-filter-bins = <256>;
 		snps,perfect-filter-entries = <128>;
 		clocks = <&clock>;
-		clock-names = "stmmaceth">;
+		clock-names = "stmmaceth";
 	};