dts: update to v4.20-rc1

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

12 files changed, 283 insertions, 35 deletions

diff --git a/dts/Bindings/net/brcm,unimac-mdio.txt b/dts/Bindings/net/brcm,unimac-mdio.txt
index 4648948f7c..e15589f477 100644
--- a/dts/Bindings/net/brcm,unimac-mdio.txt
+++ b/dts/Bindings/net/brcm,unimac-mdio.txt
@@ -19,6 +19,9 @@ Optional properties:
 - interrupt-names: must be "mdio_done_error" when there is a share interrupt fed
   to this hardware block, or must be "mdio_done" for the first interrupt and
   "mdio_error" for the second when there are separate interrupts
+- clocks: A reference to the clock supplying the MDIO bus controller
+- clock-frequency: the MDIO bus clock that must be output by the MDIO bus
+  hardware, if absent, the default hardware values are used
 
 Child nodes of this MDIO bus controller node are standard Ethernet PHY device
 nodes as described in Documentation/devicetree/bindings/net/phy.txt
diff --git a/dts/Bindings/net/can/rcar_can.txt b/dts/Bindings/net/can/rcar_can.txt
index 94a7f33ac5..cc4372842b 100644
--- a/dts/Bindings/net/can/rcar_can.txt
+++ b/dts/Bindings/net/can/rcar_can.txt
@@ -3,6 +3,7 @@ Renesas R-Car CAN controller Device Tree Bindings
 
 Required properties:
 - compatible: "renesas,can-r8a7743" if CAN controller is a part of R8A7743 SoC.
+	      "renesas,can-r8a7744" if CAN controller is a part of R8A7744 SoC.
 	      "renesas,can-r8a7745" if CAN controller is a part of R8A7745 SoC.
 	      "renesas,can-r8a7778" if CAN controller is a part of R8A7778 SoC.
 	      "renesas,can-r8a7779" if CAN controller is a part of R8A7779 SoC.
diff --git a/dts/Bindings/net/dsa/b53.txt b/dts/Bindings/net/dsa/b53.txt
index 1811e1972a..5201bc15fd 100644
--- a/dts/Bindings/net/dsa/b53.txt
+++ b/dts/Bindings/net/dsa/b53.txt
@@ -46,6 +46,42 @@ Required properties:
       "brcm,bcm6328-switch"
       "brcm,bcm6368-switch" and the mandatory "brcm,bcm63xx-switch"
 
+Required properties for BCM585xx/586xx/88312 SoCs:
+
+ - reg: a total of 3 register base addresses, the first one must be the
+   Switch Register Access block base, the second is the port 5/4 mux
+   configuration register and the third one is the SGMII configuration
+   and status register base address.
+
+ - interrupts: a total of 13 interrupts must be specified, in the following
+   order: port 0-5, 7-8 link status change, then the integrated PHY interrupt,
+   then the timestamping interrupt and the sleep timer interrupts for ports
+   5,7,8.
+
+Optional properties for BCM585xx/586xx/88312 SoCs:
+
+  - reg-names: a total of 3 names matching the 3 base register address, must
+    be in the following order:
+	"srab"
+	"mux_config"
+	"sgmii_config"
+
+  - interrupt-names: a total of 13 names matching the 13 interrupts specified
+    must be in the following order:
+	"link_state_p0"
+	"link_state_p1"
+	"link_state_p2"
+	"link_state_p3"
+	"link_state_p4"
+	"link_state_p5"
+	"link_state_p7"
+	"link_state_p8"
+	"phy"
+	"ts"
+	"imp_sleep_timer_p5"
+	"imp_sleep_timer_p7"
+	"imp_sleep_timer_p8"
+
 See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of additional
 required and optional properties.
 
diff --git a/dts/Bindings/net/dsa/lantiq-gswip.txt b/dts/Bindings/net/dsa/lantiq-gswip.txt
new file mode 100644
index 0000000000..886cbe8ffb
--- /dev/null
+++ b/dts/Bindings/net/dsa/lantiq-gswip.txt
@@ -0,0 +1,143 @@
+Lantiq GSWIP Ethernet switches
+==================================
+
+Required properties for GSWIP core:
+
+- compatible	: "lantiq,xrx200-gswip" for the embedded GSWIP in the
+		  xRX200 SoC
+- reg		: memory range of the GSWIP core registers
+		: memory range of the GSWIP MDIO registers
+		: memory range of the GSWIP MII registers
+
+See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of
+additional required and optional properties.
+
+
+Required properties for MDIO bus:
+- compatible	: "lantiq,xrx200-mdio" for the MDIO bus inside the GSWIP
+		  core of the xRX200 SoC and the PHYs connected to it.
+
+See Documentation/devicetree/bindings/net/mdio.txt for a list of additional
+required and optional properties.
+
+
+Required properties for GPHY firmware loading:
+- compatible	: "lantiq,xrx200-gphy-fw", "lantiq,gphy-fw"
+		  "lantiq,xrx300-gphy-fw", "lantiq,gphy-fw"
+		  "lantiq,xrx330-gphy-fw", "lantiq,gphy-fw"
+		  for the loading of the firmware into the embedded
+		  GPHY core of the SoC.
+- lantiq,rcu	: reference to the rcu syscon
+
+The GPHY firmware loader has a list of GPHY entries, one for each
+embedded GPHY
+
+- reg		: Offset of the GPHY firmware register in the RCU
+		  register range
+- resets	: list of resets of the embedded GPHY
+- reset-names	: list of names of the resets
+
+Example:
+
+Ethernet switch on the VRX200 SoC:
+
+switch@e108000 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	compatible = "lantiq,xrx200-gswip";
+	reg = <	0xe108000 0x3100	/* switch */
+		0xe10b100 0xd8		/* mdio */
+		0xe10b1d8 0x130		/* mii */
+		>;
+	dsa,member = <0 0>;
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+			label = "lan3";
+			phy-mode = "rgmii";
+			phy-handle = <&phy0>;
+		};
+
+		port@1 {
+			reg = <1>;
+			label = "lan4";
+			phy-mode = "rgmii";
+			phy-handle = <&phy1>;
+		};
+
+		port@2 {
+			reg = <2>;
+			label = "lan2";
+			phy-mode = "internal";
+			phy-handle = <&phy11>;
+		};
+
+		port@4 {
+			reg = <4>;
+			label = "lan1";
+			phy-mode = "internal";
+			phy-handle = <&phy13>;
+		};
+
+		port@5 {
+			reg = <5>;
+			label = "wan";
+			phy-mode = "rgmii";
+			phy-handle = <&phy5>;
+		};
+
+		port@6 {
+			reg = <0x6>;
+			label = "cpu";
+			ethernet = <&eth0>;
+		};
+	};
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "lantiq,xrx200-mdio";
+		reg = <0>;
+
+		phy0: ethernet-phy@0 {
+			reg = <0x0>;
+		};
+		phy1: ethernet-phy@1 {
+			reg = <0x1>;
+		};
+		phy5: ethernet-phy@5 {
+			reg = <0x5>;
+		};
+		phy11: ethernet-phy@11 {
+			reg = <0x11>;
+		};
+		phy13: ethernet-phy@13 {
+			reg = <0x13>;
+		};
+	};
+
+	gphy-fw {
+		compatible = "lantiq,xrx200-gphy-fw", "lantiq,gphy-fw";
+		lantiq,rcu = <&rcu0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gphy@20 {
+			reg = <0x20>;
+
+			resets = <&reset0 31 30>;
+			reset-names = "gphy";
+		};
+
+		gphy@68 {
+			reg = <0x68>;
+
+			resets = <&reset0 29 28>;
+			reset-names = "gphy";
+		};
+	};
+};
diff --git a/dts/Bindings/net/lantiq,xrx200-net.txt b/dts/Bindings/net/lantiq,xrx200-net.txt
new file mode 100644
index 0000000000..5ff5e68bbb
--- /dev/null
+++ b/dts/Bindings/net/lantiq,xrx200-net.txt
@@ -0,0 +1,21 @@
+Lantiq xRX200 GSWIP PMAC Ethernet driver
+==================================
+
+Required properties:
+
+- compatible	: "lantiq,xrx200-net" for the PMAC of the embedded
+		: GSWIP in the xXR200
+- reg		: memory range of the PMAC core inside of the GSWIP core
+- interrupts	: TX and RX DMA interrupts. Use interrupt-names "tx" for
+		: the TX interrupt and "rx" for the RX interrupt.
+
+Example:
+
+ethernet@e10b308 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	compatible = "lantiq,xrx200-net";
+	reg = <0xe10b308 0xcf8>;
+	interrupts = <73>, <72>;
+	interrupt-names = "tx", "rx";
+};
diff --git a/dts/Bindings/net/marvell,prestera.txt b/dts/Bindings/net/marvell,prestera.txt
index c329608fa8..83370ebf5b 100644
--- a/dts/Bindings/net/marvell,prestera.txt
+++ b/dts/Bindings/net/marvell,prestera.txt
@@ -2,7 +2,7 @@ Marvell Prestera Switch Chip bindings
 -------------------------------------
 
 Required properties:
-- compatible: one of the following
+- compatible: must be "marvell,prestera" and one of the following
 	"marvell,prestera-98dx3236",
 	"marvell,prestera-98dx3336",
 	"marvell,prestera-98dx4251",
@@ -21,7 +21,7 @@ switch {
 	ranges = <0 MBUS_ID(0x03, 0x00) 0 0x100000>;
 
 	packet-processor@0 {
-		compatible = "marvell,prestera-98dx3236";
+		compatible = "marvell,prestera-98dx3236", "marvell,prestera";
 		reg = <0 0x4000000>;
 		interrupts = <33>, <34>, <35>;
 		dfx = <&dfx>;
diff --git a/dts/Bindings/net/marvell-pp2.txt b/dts/Bindings/net/marvell-pp2.txt
index fc019df0d8..b783976693 100644
--- a/dts/Bindings/net/marvell-pp2.txt
+++ b/dts/Bindings/net/marvell-pp2.txt
@@ -31,7 +31,7 @@ required.
 
 Required properties (port):
 
-- interrupts: interrupt for the port
+- interrupts: interrupt(s) for the port
 - port-id: ID of the port from the MAC point of view
 - gop-port-id: only for marvell,armada-7k-pp2, ID of the port from the
   GOP (Group Of Ports) point of view. This ID is used to index the
@@ -43,10 +43,12 @@ Optional properties (port):
 - marvell,loopback: port is loopback mode
 - phy: a phandle to a phy node defining the PHY address (as the reg
   property, a single integer).
-- interrupt-names: if more than a single interrupt for rx is given, must
-                   be the name associated to the interrupts listed. Valid
-                   names are: "tx-cpu0", "tx-cpu1", "tx-cpu2", "tx-cpu3",
-		   "rx-shared", "link".
+- interrupt-names: if more than a single interrupt for is given, must be the
+                   name associated to the interrupts listed. Valid names are:
+                   "hifX", with X in [0..8], and "link". The names "tx-cpu0",
+                   "tx-cpu1", "tx-cpu2", "tx-cpu3" and "rx-shared" are supported
+                   for backward compatibility but shouldn't be used for new
+                   additions.
 - marvell,system-controller: a phandle to the system controller.
 
 Example for marvell,armada-375-pp2:
@@ -89,9 +91,14 @@ cpm_ethernet: ethernet@0 {
 			     <ICU_GRP_NSR 43 IRQ_TYPE_LEVEL_HIGH>,
 			     <ICU_GRP_NSR 47 IRQ_TYPE_LEVEL_HIGH>,
 			     <ICU_GRP_NSR 51 IRQ_TYPE_LEVEL_HIGH>,
-			     <ICU_GRP_NSR 55 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-names = "tx-cpu0", "tx-cpu1", "tx-cpu2",
-				  "tx-cpu3", "rx-shared";
+			     <ICU_GRP_NSR 55 IRQ_TYPE_LEVEL_HIGH>,
+			     <ICU_GRP_NSR 59 IRQ_TYPE_LEVEL_HIGH>,
+			     <ICU_GRP_NSR 63 IRQ_TYPE_LEVEL_HIGH>,
+			     <ICU_GRP_NSR 67 IRQ_TYPE_LEVEL_HIGH>,
+			     <ICU_GRP_NSR 71 IRQ_TYPE_LEVEL_HIGH>,
+			     <ICU_GRP_NSR 129 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "hif0", "hif1", "hif2", "hif3", "hif4",
+				  "hif5", "hif6", "hif7", "hif8", "link";
 		port-id = <0>;
 		gop-port-id = <0>;
 	};
@@ -101,9 +108,14 @@ cpm_ethernet: ethernet@0 {
 			     <ICU_GRP_NSR 44 IRQ_TYPE_LEVEL_HIGH>,
 			     <ICU_GRP_NSR 48 IRQ_TYPE_LEVEL_HIGH>,
 			     <ICU_GRP_NSR 52 IRQ_TYPE_LEVEL_HIGH>,
-			     <ICU_GRP_NSR 56 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-names = "tx-cpu0", "tx-cpu1", "tx-cpu2",
-				  "tx-cpu3", "rx-shared";
+			     <ICU_GRP_NSR 56 IRQ_TYPE_LEVEL_HIGH>,
+			     <ICU_GRP_NSR 60 IRQ_TYPE_LEVEL_HIGH>,
+			     <ICU_GRP_NSR 64 IRQ_TYPE_LEVEL_HIGH>,
+			     <ICU_GRP_NSR 68 IRQ_TYPE_LEVEL_HIGH>,
+			     <ICU_GRP_NSR 72 IRQ_TYPE_LEVEL_HIGH>,
+			     <ICU_GRP_NSR 128 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "hif0", "hif1", "hif2", "hif3", "hif4",
+				  "hif5", "hif6", "hif7", "hif8", "link";
 		port-id = <1>;
 		gop-port-id = <2>;
 	};
@@ -113,9 +125,14 @@ cpm_ethernet: ethernet@0 {
 			     <ICU_GRP_NSR 45 IRQ_TYPE_LEVEL_HIGH>,
 			     <ICU_GRP_NSR 49 IRQ_TYPE_LEVEL_HIGH>,
 			     <ICU_GRP_NSR 53 IRQ_TYPE_LEVEL_HIGH>,
-			     <ICU_GRP_NSR 57 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-names = "tx-cpu0", "tx-cpu1", "tx-cpu2",
-				  "tx-cpu3", "rx-shared";
+			     <ICU_GRP_NSR 57 IRQ_TYPE_LEVEL_HIGH>,
+			     <ICU_GRP_NSR 61 IRQ_TYPE_LEVEL_HIGH>,
+			     <ICU_GRP_NSR 65 IRQ_TYPE_LEVEL_HIGH>,
+			     <ICU_GRP_NSR 69 IRQ_TYPE_LEVEL_HIGH>,
+			     <ICU_GRP_NSR 73 IRQ_TYPE_LEVEL_HIGH>,
+			     <ICU_GRP_NSR 127 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "hif0", "hif1", "hif2", "hif3", "hif4",
+				  "hif5", "hif6", "hif7", "hif8", "link";
 		port-id = <2>;
 		gop-port-id = <3>;
 	};
diff --git a/dts/Bindings/net/micrel-ksz90x1.txt b/dts/Bindings/net/micrel-ksz90x1.txt
index e22d8cfea6..5100358177 100644
--- a/dts/Bindings/net/micrel-ksz90x1.txt
+++ b/dts/Bindings/net/micrel-ksz90x1.txt
@@ -1,4 +1,4 @@
-Micrel KSZ9021/KSZ9031 Gigabit Ethernet PHY
+Micrel KSZ9021/KSZ9031/KSZ9131 Gigabit Ethernet PHY
 
 Some boards require special tuning values, particularly when it comes
 to clock delays. You can specify clock delay values in the PHY OF
@@ -64,6 +64,32 @@ KSZ9031:
         Attention: The link partner must be configurable as slave otherwise
         no link will be established.
 
+KSZ9131:
+
+  All skew control options are specified in picoseconds. The increment
+  step is 100ps. Unlike KSZ9031, the values represent picoseccond delays.
+  A negative value can be assigned as rxc-skew-psec = <(-100)>;.
+
+  Optional properties:
+
+    Range of the value -700 to 2400, default value 0:
+
+      - rxc-skew-psec : Skew control of RX clock pad
+      - txc-skew-psec : Skew control of TX clock pad
+
+    Range of the value -700 to 800, default value 0:
+
+      - rxdv-skew-psec : Skew control of RX CTL pad
+      - txen-skew-psec : Skew control of TX CTL pad
+      - rxd0-skew-psec : Skew control of RX data 0 pad
+      - rxd1-skew-psec : Skew control of RX data 1 pad
+      - rxd2-skew-psec : Skew control of RX data 2 pad
+      - rxd3-skew-psec : Skew control of RX data 3 pad
+      - txd0-skew-psec : Skew control of TX data 0 pad
+      - txd1-skew-psec : Skew control of TX data 1 pad
+      - txd2-skew-psec : Skew control of TX data 2 pad
+      - txd3-skew-psec : Skew control of TX data 3 pad
+
 Examples:
 
 	mdio {
diff --git a/dts/Bindings/net/mscc-ocelot.txt b/dts/Bindings/net/mscc-ocelot.txt
index 0a84711abe..9e5c17d426 100644
--- a/dts/Bindings/net/mscc-ocelot.txt
+++ b/dts/Bindings/net/mscc-ocelot.txt
@@ -12,7 +12,6 @@ Required properties:
   - "sys"
   - "rew"
   - "qs"
-  - "hsio"
   - "qsys"
   - "ana"
   - "portX" with X from 0 to the number of last port index available on that
@@ -45,7 +44,6 @@ Example:
 		reg = <0x1010000 0x10000>,
 		      <0x1030000 0x10000>,
 		      <0x1080000 0x100>,
-		      <0x10d0000 0x10000>,
 		      <0x11e0000 0x100>,
 		      <0x11f0000 0x100>,
 		      <0x1200000 0x100>,
@@ -59,10 +57,9 @@ Example:
 		      <0x1280000 0x100>,
 		      <0x1800000 0x80000>,
 		      <0x1880000 0x10000>;
-		reg-names = "sys", "rew", "qs", "hsio", "port0",
-			    "port1", "port2", "port3", "port4", "port5",
-			    "port6", "port7", "port8", "port9", "port10",
-			    "qsys", "ana";
+		reg-names = "sys", "rew", "qs", "port0", "port1", "port2",
+			    "port3", "port4", "port5", "port6", "port7",
+			    "port8", "port9", "port10", "qsys", "ana";
 		interrupts = <21 22>;
 		interrupt-names = "xtr", "inj";
 
diff --git a/dts/Bindings/net/mscc-phy-vsc8531.txt b/dts/Bindings/net/mscc-phy-vsc8531.txt
index 0eedabe22c..5ff37c68c9 100644
--- a/dts/Bindings/net/mscc-phy-vsc8531.txt
+++ b/dts/Bindings/net/mscc-phy-vsc8531.txt
@@ -1,10 +1,5 @@
 * Microsemi - vsc8531 Giga bit ethernet phy
 
-Required properties:
-- compatible	: Should contain phy id as "ethernet-phy-idAAAA.BBBB"
-		  The PHY device uses the binding described in
-		  Documentation/devicetree/bindings/net/phy.txt
-
 Optional properties:
 - vsc8531,vddmac	: The vddmac in mV. Allowed values is listed
 			  in the first row of Table 1 (below).
@@ -27,14 +22,16 @@ Optional properties:
 			  'vddmac'.
 			  Default value is 0%.
 			  Ref: Table:1 - Edge rate change (below).
-- vsc8531,led-0-mode	: LED mode. Specify how the LED[0] should behave.
-			  Allowed values are define in
-			  "include/dt-bindings/net/mscc-phy-vsc8531.h".
-			  Default value is VSC8531_LINK_1000_ACTIVITY (1).
-- vsc8531,led-1-mode	: LED mode. Specify how the LED[1] should behave.
-			  Allowed values are define in
+- vsc8531,led-[N]-mode	: LED mode. Specify how the LED[N] should behave.
+			  N depends on the number of LEDs supported by a
+			  PHY.
+			  Allowed values are defined in
 			  "include/dt-bindings/net/mscc-phy-vsc8531.h".
-			  Default value is VSC8531_LINK_100_ACTIVITY (2).
+			  Default values are VSC8531_LINK_1000_ACTIVITY (1),
+			  VSC8531_LINK_100_ACTIVITY (2),
+			  VSC8531_LINK_ACTIVITY (0) and
+			  VSC8531_DUPLEX_COLLISION (8).
+
 
 Table: 1 - Edge rate change
 ----------------------------------------------------------------|
diff --git a/dts/Bindings/net/renesas,ravb.txt b/dts/Bindings/net/renesas,ravb.txt
index da249b7c40..3530256a87 100644
--- a/dts/Bindings/net/renesas,ravb.txt
+++ b/dts/Bindings/net/renesas,ravb.txt
@@ -6,6 +6,7 @@ interface contains.
 Required properties:
 - compatible: Must contain one or more of the following:
       - "renesas,etheravb-r8a7743" for the R8A7743 SoC.
+      - "renesas,etheravb-r8a7744" for the R8A7744 SoC.
       - "renesas,etheravb-r8a7745" for the R8A7745 SoC.
       - "renesas,etheravb-r8a77470" for the R8A77470 SoC.
       - "renesas,etheravb-r8a7790" for the R8A7790 SoC.
diff --git a/dts/Bindings/net/wireless/qcom,ath10k.txt b/dts/Bindings/net/wireless/qcom,ath10k.txt
index 7fd4e8ce41..2196d1ab3c 100644
--- a/dts/Bindings/net/wireless/qcom,ath10k.txt
+++ b/dts/Bindings/net/wireless/qcom,ath10k.txt
@@ -56,6 +56,11 @@ Optional properties:
 				     the length can vary between hw versions.
 - <supply-name>-supply: handle to the regulator device tree node
 			   optional "supply-name" is "vdd-0.8-cx-mx".
+- memory-region:
+	Usage: optional
+	Value type: <phandle>
+	Definition: reference to the reserved-memory for the msa region
+		    used by the wifi firmware running in Q6.
 
 Example (to supply the calibration data alone):
 
@@ -149,4 +154,5 @@ wifi@18000000 {
 			   <0 140 0 /* CE10 */ >,
 			   <0 141 0 /* CE11 */ >;
 		vdd-0.8-cx-mx-supply = <&pm8998_l5>;
+		memory-region = <&wifi_msa_mem>;
 };