dts: update to v4.9-rc1

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

20 files changed, 615 insertions, 27 deletions

diff --git a/dts/Bindings/net/apm-xgene-enet.txt b/dts/Bindings/net/apm-xgene-enet.txt
index e41b2d59ca..f591ab782d 100644
--- a/dts/Bindings/net/apm-xgene-enet.txt
+++ b/dts/Bindings/net/apm-xgene-enet.txt
@@ -47,6 +47,9 @@ Optional properties:
 	    Valid values are between 0 to 7, that maps to
 	    273, 589, 899, 1222, 1480, 1806, 2147, 2464 ps
 	    Default value is 2, which corresponds to 899 ps
+- rxlos-gpios: Input gpio from SFP+ module to indicate availability of
+	       incoming signal.
+
 
 Example:
 	menetclk: menetclk {
diff --git a/dts/Bindings/net/brcm,amac.txt b/dts/Bindings/net/brcm,amac.txt
new file mode 100644
index 0000000000..ba5ecc1041
--- /dev/null
+++ b/dts/Bindings/net/brcm,amac.txt
@@ -0,0 +1,24 @@
+Broadcom AMAC Ethernet Controller Device Tree Bindings
+-------------------------------------------------------------
+
+Required properties:
+ - compatible:	"brcm,amac" or "brcm,nsp-amac"
+ - reg:		Address and length of the GMAC registers,
+		Address and length of the GMAC IDM registers
+ - reg-names:	Names of the registers.  Must have both "amac_base" and
+		"idm_base"
+ - interrupts:	Interrupt number
+
+Optional properties:
+- mac-address:	See ethernet.txt file in the same directory
+
+Examples:
+
+amac0: ethernet@18022000 {
+	compatible = "brcm,nsp-amac";
+	reg = <0x18022000 0x1000>,
+	      <0x18110000 0x1000>;
+	reg-names = "amac_base", "idm_base";
+	interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>;
+	status = "disabled";
+};
diff --git a/dts/Bindings/net/brcm,bcm7445-switch-v4.0.txt b/dts/Bindings/net/brcm,bcm7445-switch-v4.0.txt
index 30d487597e..fb40891ee6 100644
--- a/dts/Bindings/net/brcm,bcm7445-switch-v4.0.txt
+++ b/dts/Bindings/net/brcm,bcm7445-switch-v4.0.txt
@@ -6,9 +6,13 @@ Required properties:
 - reg: addresses and length of the register sets for the device, must be 6
   pairs of register addresses and lengths
 - interrupts: interrupts for the devices, must be two interrupts
+- #address-cells: must be 1, see dsa/dsa.txt
+- #size-cells: must be 0, see dsa/dsa.txt
+
+Deprecated binding required properties:
+
 - dsa,mii-bus: phandle to the MDIO bus controller, see dsa/dsa.txt
 - dsa,ethernet: phandle to the CPU network interface controller, see dsa/dsa.txt
-- #size-cells: must be 0
 - #address-cells: must be 2, see dsa/dsa.txt
 
 Subnodes:
@@ -48,6 +52,45 @@ switch_top@f0b00000 {
 	ethernet_switch@0 {
 		compatible = "brcm,bcm7445-switch-v4.0";
 		#size-cells = <0>;
+		#address-cells = <1>;
+		reg = <0x0 0x40000
+			0x40000 0x110
+			0x40340 0x30
+			0x40380 0x30
+			0x40400 0x34
+			0x40600 0x208>;
+		reg-names = "core", "reg", intrl2_0", "intrl2_1",
+			    "fcb, "acb";
+		interrupts = <0 0x18 0
+				0 0x19 0>;
+		brcm,num-gphy = <1>;
+		brcm,num-rgmii-ports = <2>;
+		brcm,fcb-pause-override;
+		brcm,acb-packets-inflight;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				label = "gphy";
+				reg = <0>;
+			};
+		};
+	};
+};
+
+Example using the old DSA DeviceTree binding:
+
+switch_top@f0b00000 {
+	compatible = "simple-bus";
+	#size-cells = <1>;
+	#address-cells = <1>;
+	ranges = <0 0xf0b00000 0x40804>;
+
+	ethernet_switch@0 {
+		compatible = "brcm,bcm7445-switch-v4.0";
+		#size-cells = <0>;
 		#address-cells = <2>;
 		reg = <0x0 0x40000
 			0x40000 0x110
diff --git a/dts/Bindings/net/brcm,bgmac-nsp.txt b/dts/Bindings/net/brcm,bgmac-nsp.txt
new file mode 100644
index 0000000000..022946caa7
--- /dev/null
+++ b/dts/Bindings/net/brcm,bgmac-nsp.txt
@@ -0,0 +1,24 @@
+Broadcom GMAC Ethernet Controller Device Tree Bindings
+-------------------------------------------------------------
+
+Required properties:
+ - compatible:	"brcm,bgmac-nsp"
+ - reg:		Address and length of the GMAC registers,
+		Address and length of the GMAC IDM registers
+ - reg-names:	Names of the registers.  Must have both "gmac_base" and
+		"idm_base"
+ - interrupts:	Interrupt number
+
+Optional properties:
+- mac-address:	See ethernet.txt file in the same directory
+
+Examples:
+
+gmac0: ethernet@18022000 {
+	compatible = "brcm,bgmac-nsp";
+	reg = <0x18022000 0x1000>,
+	      <0x18110000 0x1000>;
+	reg-names = "gmac_base", "idm_base";
+	interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>;
+	status = "disabled";
+};
diff --git a/dts/Bindings/net/dsa/qca8k.txt b/dts/Bindings/net/dsa/qca8k.txt
new file mode 100644
index 0000000000..9c67ee4890
--- /dev/null
+++ b/dts/Bindings/net/dsa/qca8k.txt
@@ -0,0 +1,89 @@
+* Qualcomm Atheros QCA8xxx switch family
+
+Required properties:
+
+- compatible: should be "qca,qca8337"
+- #size-cells: must be 0
+- #address-cells: must be 1
+
+Subnodes:
+
+The integrated switch subnode should be specified according to the binding
+described in dsa/dsa.txt. As the QCA8K switches do not have a N:N mapping of
+port and PHY id, each subnode describing a port needs to have a valid phandle
+referencing the internal PHY connected to it. The CPU port of this switch is
+always port 0.
+
+Example:
+
+
+	&mdio0 {
+		phy_port1: phy@0 {
+			reg = <0>;
+		};
+
+		phy_port2: phy@1 {
+			reg = <1>;
+		};
+
+		phy_port3: phy@2 {
+			reg = <2>;
+		};
+
+		phy_port4: phy@3 {
+			reg = <3>;
+		};
+
+		phy_port5: phy@4 {
+			reg = <4>;
+		};
+
+		switch0@0 {
+			compatible = "qca,qca8337";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			reg = <0>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				port@0 {
+					reg = <0>;
+					label = "cpu";
+					ethernet = <&gmac1>;
+					phy-mode = "rgmii";
+				};
+
+				port@1 {
+					reg = <1>;
+					label = "lan1";
+					phy-handle = <&phy_port1>;
+				};
+
+				port@2 {
+					reg = <2>;
+					label = "lan2";
+					phy-handle = <&phy_port2>;
+				};
+
+				port@3 {
+					reg = <3>;
+					label = "lan3";
+					phy-handle = <&phy_port3>;
+				};
+
+				port@4 {
+					reg = <4>;
+					label = "lan4";
+					phy-handle = <&phy_port4>;
+				};
+
+				port@5 {
+					reg = <5>;
+					label = "wan";
+					phy-handle = <&phy_port5>;
+				};
+			};
+		};
+	};
diff --git a/dts/Bindings/net/ethernet.txt b/dts/Bindings/net/ethernet.txt
index 5d88f37480..e1d7681241 100644
--- a/dts/Bindings/net/ethernet.txt
+++ b/dts/Bindings/net/ethernet.txt
@@ -11,8 +11,8 @@ The following properties are common to the Ethernet controllers:
   the maximum frame size (there's contradiction in ePAPR).
 - phy-mode: string, operation mode of the PHY interface; supported values are
   "mii", "gmii", "sgmii", "qsgmii", "tbi", "rev-mii", "rmii", "rgmii", "rgmii-id",
-  "rgmii-rxid", "rgmii-txid", "rtbi", "smii", "xgmii"; this is now a de-facto
-  standard property;
+  "rgmii-rxid", "rgmii-txid", "rtbi", "smii", "xgmii", "trgmii"; this is now a
+  de-facto standard property;
 - phy-connection-type: the same as "phy-mode" property but described in ePAPR;
 - phy-handle: phandle, specifies a reference to a node representing a PHY
   device; this property is described in ePAPR and so preferred;
diff --git a/dts/Bindings/net/macb.txt b/dts/Bindings/net/macb.txt
index b5a42df4c9..1506e94861 100644
--- a/dts/Bindings/net/macb.txt
+++ b/dts/Bindings/net/macb.txt
@@ -21,6 +21,7 @@ Required properties:
 - clock-names: Tuple listing input clock names.
 	Required elements: 'pclk', 'hclk'
 	Optional elements: 'tx_clk'
+	Optional elements: 'rx_clk' applies to cdns,zynqmp-gem
 - clocks: Phandles to input clocks.
 
 Optional properties for PHY child node:
diff --git a/dts/Bindings/net/mediatek-net.txt b/dts/Bindings/net/mediatek-net.txt
index 32eaaca04d..c010fafc66 100644
--- a/dts/Bindings/net/mediatek-net.txt
+++ b/dts/Bindings/net/mediatek-net.txt
@@ -25,13 +25,15 @@ Optional properties:
 - interrupt-parent: Should be the phandle for the interrupt controller
   that services interrupts for this device
 
-
 * Ethernet MAC node
 
 Required properties:
 - compatible: Should be "mediatek,eth-mac"
 - reg: The number of the MAC
-- phy-handle: see ethernet.txt file in the same directory.
+- phy-handle: see ethernet.txt file in the same directory and
+	the phy-mode "trgmii" required being provided when reg
+	is equal to 0 and the MAC uses fixed-link to connect
+	with internal switch such as MT7530.
 
 Example:
 
diff --git a/dts/Bindings/net/meson-dwmac.txt b/dts/Bindings/net/meson-dwmac.txt
index ec633d74a8..89e62ddc69 100644
--- a/dts/Bindings/net/meson-dwmac.txt
+++ b/dts/Bindings/net/meson-dwmac.txt
@@ -1,18 +1,32 @@
 * Amlogic Meson DWMAC Ethernet controller
 
 The device inherits all the properties of the dwmac/stmmac devices
-described in the file net/stmmac.txt with the following changes.
+described in the file stmmac.txt in the current directory with the
+following changes.
 
-Required properties:
+Required properties on all platforms:
 
-- compatible: should be "amlogic,meson6-dwmac" along with "snps,dwmac"
-	      and any applicable more detailed version number
-	      described in net/stmmac.txt
+- compatible:	Depending on the platform this should be one of:
+			- "amlogic,meson6-dwmac"
+			- "amlogic,meson8b-dwmac"
+			- "amlogic,meson-gxbb-dwmac"
+		Additionally "snps,dwmac" and any applicable more
+		detailed version number described in net/stmmac.txt
+		should be used.
 
-- reg: should contain a register range for the dwmac controller and
-       another one for the Amlogic specific configuration
+- reg:	The first register range should be the one of the DWMAC
+	controller. The second range is is for the Amlogic specific
+	configuration (for example the PRG_ETHERNET register range
+	on Meson8b and newer)
 
-Example:
+Required properties on Meson8b and newer:
+- clock-names:	Should contain the following:
+		- "stmmaceth" - see stmmac.txt
+		- "clkin0" - first parent clock of the internal mux
+		- "clkin1" - second parent clock of the internal mux
+
+
+Example for Meson6:
 
 	ethmac: ethernet@c9410000 {
 		compatible = "amlogic,meson6-dwmac", "snps,dwmac";
@@ -23,3 +37,18 @@ Example:
 		clocks = <&clk81>;
 		clock-names = "stmmaceth";
 	}
+
+Example for GXBB:
+	ethmac: ethernet@c9410000 {
+		compatible = "amlogic,meson-gxbb-dwmac", "snps,dwmac";
+		reg = <0x0 0xc9410000 0x0 0x10000>,
+			<0x0 0xc8834540 0x0 0x8>;
+		interrupts = <0 8 1>;
+		interrupt-names = "macirq";
+		clocks = <&clkc CLKID_ETH>,
+				<&clkc CLKID_FCLK_DIV2>,
+				<&clkc CLKID_MPLL2>;
+		clock-names = "stmmaceth", "clkin0", "clkin1";
+		phy-mode = "rgmii";
+		status = "disabled";
+	};
diff --git a/dts/Bindings/net/micrel-ksz90x1.txt b/dts/Bindings/net/micrel-ksz90x1.txt
index f9c32adab5..c35b5b428a 100644
--- a/dts/Bindings/net/micrel-ksz90x1.txt
+++ b/dts/Bindings/net/micrel-ksz90x1.txt
@@ -34,16 +34,17 @@ KSZ9031:
 
   All skew control options are specified in picoseconds. The minimum
   value is 0, and the maximum is property-dependent. The increment
-  step is 60ps.
+  step is 60ps. The default value is the neutral setting, so setting
+  rxc-skew-ps=<0> actually results in -900 picoseconds adjustment.
 
   Optional properties:
 
-    Maximum value of 1860:
+    Maximum value of 1860, default value 900:
 
       - rxc-skew-ps : Skew control of RX clock pad
       - txc-skew-ps : Skew control of TX clock pad
 
-    Maximum value of 900:
+    Maximum value of 900, default value 420:
 
       - rxdv-skew-ps : Skew control of RX CTL pad
       - txen-skew-ps : Skew control of TX CTL pad
diff --git a/dts/Bindings/net/mscc-phy-vsc8531.txt b/dts/Bindings/net/mscc-phy-vsc8531.txt
new file mode 100644
index 0000000000..99c7eb0a00
--- /dev/null
+++ b/dts/Bindings/net/mscc-phy-vsc8531.txt
@@ -0,0 +1,58 @@
+* Microsemi - vsc8531 Giga bit ethernet phy
+
+Required properties:
+- compatible	: Should contain phy id as "ethernet-phy-idAAAA.BBBB"
+		  The PHY device uses the binding described in
+		  Documentation/devicetree/bindings/net/phy.txt
+
+Optional properties:
+- vsc8531,vddmac	: The vddmac in mV.
+- vsc8531,edge-slowdown	: % the edge should be slowed down relative to
+			  the fastest possible edge time. Native sign
+			  need not enter.
+			  Edge rate sets the drive strength of the MAC
+			  interface output signals.  Changing the drive
+			  strength will affect the edge rate of the output
+			  signal.  The goal of this setting is to help
+			  reduce electrical emission (EMI) by being able
+			  to reprogram drive strength and in effect slow
+			  down the edge rate if desired.  Table 1 shows the
+			  impact to the edge rate per VDDMAC supply for each
+			  drive strength setting.
+			  Ref: Table:1 - Edge rate change below.
+
+Note: see dt-bindings/net/mscc-phy-vsc8531.h for applicable values
+
+Table: 1 - Edge rate change
+----------------------------------------------------------------|
+| 		Edge Rate Change (VDDMAC)			|
+|								|
+| 3300 mV	2500 mV		1800 mV		1500 mV		|
+|---------------------------------------------------------------|
+| Default	Deafult		Default		Default		|
+| (Fastest)			(recommended)	(recommended)	|
+|---------------------------------------------------------------|
+| -2%		-3%		-5%		-6%		|
+|---------------------------------------------------------------|
+| -4%		-6%		-9%		-14%		|
+|---------------------------------------------------------------|
+| -7%		-10%		-16%		-21%		|
+|(recommended)	(recommended)					|
+|---------------------------------------------------------------|
+| -10%		-14%		-23%		-29%		|
+|---------------------------------------------------------------|
+| -17%		-23%		-35%		-42%		|
+|---------------------------------------------------------------|
+| -29%		-37%		-52%		-58%		|
+|---------------------------------------------------------------|
+| -53%		-63%		-76%		-77%		|
+| (slowest)							|
+|---------------------------------------------------------------|
+
+Example:
+
+        vsc8531_0: ethernet-phy@0 {
+                compatible = "ethernet-phy-id0007.0570";
+                vsc8531,vddmac		= <3300>;
+                vsc8531,edge-slowdown	= <21>;
+        };
diff --git a/dts/Bindings/net/qcom-emac.txt b/dts/Bindings/net/qcom-emac.txt
new file mode 100644
index 0000000000..346e6c7f47
--- /dev/null
+++ b/dts/Bindings/net/qcom-emac.txt
@@ -0,0 +1,111 @@
+Qualcomm Technologies EMAC Gigabit Ethernet Controller
+
+This network controller consists of two devices: a MAC and an SGMII
+internal PHY.  Each device is represented by a device tree node.  A phandle
+connects the MAC node to its corresponding internal phy node.  Another
+phandle points to the external PHY node.
+
+Required properties:
+
+MAC node:
+- compatible : Should be "qcom,fsm9900-emac".
+- reg : Offset and length of the register regions for the device
+- interrupts : Interrupt number used by this controller
+- mac-address : The 6-byte MAC address. If present, it is the default
+	MAC address.
+- internal-phy : phandle to the internal PHY node
+- phy-handle : phandle the the external PHY node
+
+Internal PHY node:
+- compatible : Should be "qcom,fsm9900-emac-sgmii" or "qcom,qdf2432-emac-sgmii".
+- reg : Offset and length of the register region(s) for the device
+- interrupts : Interrupt number used by this controller
+
+The external phy child node:
+- reg : The phy address
+
+Example:
+
+FSM9900:
+
+soc {
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	emac0: ethernet@feb20000 {
+		compatible = "qcom,fsm9900-emac";
+		reg = <0xfeb20000 0x10000>,
+		      <0xfeb36000 0x1000>;
+		interrupts = <76>;
+
+		clocks = <&gcc 0>, <&gcc 1>, <&gcc 3>, <&gcc 4>, <&gcc 5>,
+			<&gcc 6>, <&gcc 7>;
+		clock-names = "axi_clk", "cfg_ahb_clk", "high_speed_clk",
+			"mdio_clk", "tx_clk", "rx_clk", "sys_clk";
+
+		internal-phy = <&emac_sgmii>;
+
+		phy-handle = <&phy0>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+		phy0: ethernet-phy@0 {
+			reg = <0>;
+		};
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&mdio_pins_a>;
+	};
+
+	emac_sgmii: ethernet@feb38000 {
+		compatible = "qcom,fsm9900-emac-sgmii";
+		reg = <0xfeb38000 0x1000>;
+		interrupts = <80>;
+	};
+
+	tlmm: pinctrl@fd510000 {
+		compatible = "qcom,fsm9900-pinctrl";
+
+		mdio_pins_a: mdio {
+			state {
+				pins = "gpio123", "gpio124";
+				function = "mdio";
+			};
+		};
+	};
+
+
+QDF2432:
+
+soc {
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	emac0: ethernet@38800000 {
+		compatible = "qcom,fsm9900-emac";
+		reg = <0x0 0x38800000 0x0 0x10000>,
+		      <0x0 0x38816000 0x0 0x1000>;
+		interrupts = <0 256 4>;
+
+		clocks = <&gcc 0>, <&gcc 1>, <&gcc 3>, <&gcc 4>, <&gcc 5>,
+			 <&gcc 6>, <&gcc 7>;
+		clock-names = "axi_clk", "cfg_ahb_clk", "high_speed_clk",
+			"mdio_clk", "tx_clk", "rx_clk", "sys_clk";
+
+		internal-phy = <&emac_sgmii>;
+
+		phy-handle = <&phy0>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+		phy0: ethernet-phy@4 {
+			reg = <4>;
+		};
+	};
+
+	emac_sgmii: ethernet@410400 {
+		compatible = "qcom,qdf2432-emac-sgmii";
+		reg = <0x0 0x00410400 0x0 0xc00>, /* Base address */
+		      <0x0 0x00410000 0x0 0x400>; /* Per-lane digital */
+		interrupts = <0 254 1>;
+	};
diff --git a/dts/Bindings/net/renesas,ravb.txt b/dts/Bindings/net/renesas,ravb.txt
index c8ac222eac..b519503be5 100644
--- a/dts/Bindings/net/renesas,ravb.txt
+++ b/dts/Bindings/net/renesas,ravb.txt
@@ -10,6 +10,7 @@ Required properties:
 	      "renesas,etheravb-r8a7793" if the device is a part of R8A7793 SoC.
 	      "renesas,etheravb-r8a7794" if the device is a part of R8A7794 SoC.
 	      "renesas,etheravb-r8a7795" if the device is a part of R8A7795 SoC.
+	      "renesas,etheravb-r8a7796" if the device is a part of R8A7796 SoC.
 	      "renesas,etheravb-rcar-gen2" for generic R-Car Gen 2 compatible interface.
 	      "renesas,etheravb-rcar-gen3" for generic R-Car Gen 3 compatible interface.
 
@@ -33,7 +34,7 @@ Optional properties:
 - interrupt-parent: the phandle for the interrupt controller that services
 		    interrupts for this device.
 - interrupt-names: A list of interrupt names.
-		   For the R8A7795 SoC this property is mandatory;
+		   For the R8A779[56] SoCs this property is mandatory;
 		   it should include one entry per channel, named "ch%u",
 		   where %u is the channel number ranging from 0 to 24.
 		   For other SoCs this property is optional; if present
diff --git a/dts/Bindings/net/rockchip-dwmac.txt b/dts/Bindings/net/rockchip-dwmac.txt
index cccd945fc4..95383c5131 100644
--- a/dts/Bindings/net/rockchip-dwmac.txt
+++ b/dts/Bindings/net/rockchip-dwmac.txt
@@ -3,8 +3,12 @@ Rockchip SoC RK3288 10/100/1000 Ethernet driver(GMAC)
 The device node has following properties.
 
 Required properties:
- - compatible: Can be one of "rockchip,rk3228-gmac", "rockchip,rk3288-gmac",
-                             "rockchip,rk3368-gmac"
+ - compatible: should be "rockchip,<name>-gamc"
+   "rockchip,rk3228-gmac": found on RK322x SoCs
+   "rockchip,rk3288-gmac": found on RK3288 SoCs
+   "rockchip,rk3366-gmac": found on RK3366 SoCs
+   "rockchip,rk3368-gmac": found on RK3368 SoCs
+   "rockchip,rk3399-gmac": found on RK3399 SoCs
  - reg: addresses and length of the register sets for the device.
  - interrupts: Should contain the GMAC interrupts.
  - interrupt-names: Should contain the interrupt names "macirq".
diff --git a/dts/Bindings/net/sh_eth.txt b/dts/Bindings/net/sh_eth.txt
index 2f6ec85fda..0115c85a24 100644
--- a/dts/Bindings/net/sh_eth.txt
+++ b/dts/Bindings/net/sh_eth.txt
@@ -5,6 +5,8 @@ interface contains.
 
 Required properties:
 - compatible: "renesas,gether-r8a7740" if the device is a part of R8A7740 SoC.
+	      "renesas,ether-r8a7743"  if the device is a part of R8A7743 SoC.
+	      "renesas,ether-r8a7745"  if the device is a part of R8A7745 SoC.
 	      "renesas,ether-r8a7778"  if the device is a part of R8A7778 SoC.
 	      "renesas,ether-r8a7779"  if the device is a part of R8A7779 SoC.
 	      "renesas,ether-r8a7790"  if the device is a part of R8A7790 SoC.
diff --git a/dts/Bindings/net/smsc911x.txt b/dts/Bindings/net/smsc911x.txt
index 3fed3c1244..16c3a9501f 100644
--- a/dts/Bindings/net/smsc911x.txt
+++ b/dts/Bindings/net/smsc911x.txt
@@ -3,9 +3,11 @@
 Required properties:
 - compatible : Should be "smsc,lan<model>", "smsc,lan9115"
 - reg : Address and length of the io space for SMSC LAN
-- interrupts : Should contain SMSC LAN interrupt line
-- interrupt-parent : Should be the phandle for the interrupt controller
-  that services interrupts for this device
+- interrupts : one or two interrupt specifiers
+  - The first interrupt is the SMSC LAN interrupt line
+  - The second interrupt (if present) is the PME (power
+    management event) interrupt that is able to wake up the host
+     system with a 50ms pulse on network activity
 - phy-mode : See ethernet.txt file in the same directory
 
 Optional properties:
@@ -21,6 +23,10 @@ Optional properties:
   external PHY
 - smsc,save-mac-address : Indicates that mac address needs to be saved
   before resetting the controller
+- reset-gpios : a GPIO line connected to the RESET (active low) signal
+  of the device. On many systems this is wired high so the device goes
+  out of reset at power-on, but if it is under program control, this
+  optional GPIO can wake up in response to it.
 
 Examples:
 
@@ -29,7 +35,8 @@ lan9220@f4000000 {
 	reg = <0xf4000000 0x2000000>;
 	phy-mode = "mii";
 	interrupt-parent = <&gpio1>;
-	interrupts = <31>;
+	interrupts = <31>, <32>;
+	reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
 	reg-io-width = <4>;
 	smsc,irq-push-pull;
 };
diff --git a/dts/Bindings/net/snps,dwc-qos-ethernet.txt b/dts/Bindings/net/snps,dwc-qos-ethernet.txt
index 51f8d2eba8..d93f71ce83 100644
--- a/dts/Bindings/net/snps,dwc-qos-ethernet.txt
+++ b/dts/Bindings/net/snps,dwc-qos-ethernet.txt
@@ -1,21 +1,111 @@
 * Synopsys DWC Ethernet QoS IP version 4.10 driver (GMAC)
 
+This binding supports the Synopsys Designware Ethernet QoS (Quality Of Service)
+IP block. The IP supports multiple options for bus type, clocking and reset
+structure, and feature list. Consequently, a number of properties and list
+entries in properties are marked as optional, or only required in specific HW
+configurations.
 
 Required properties:
-- compatible: Should be "snps,dwc-qos-ethernet-4.10"
+- compatible: One of:
+  - "axis,artpec6-eqos", "snps,dwc-qos-ethernet-4.10"
+    Represents the IP core when integrated into the Axis ARTPEC-6 SoC.
+  - "nvidia,tegra186-eqos", "snps,dwc-qos-ethernet-4.10"
+    Represents the IP core when integrated into the NVIDIA Tegra186 SoC.
+  - "snps,dwc-qos-ethernet-4.10"
+    This combination is deprecated. It should be treated as equivalent to
+    "axis,artpec6-eqos", "snps,dwc-qos-ethernet-4.10". It is supported to be
+    compatible with earlier revisions of this binding.
 - reg: Address and length of the register set for the device
-- clocks: Phandles to the reference clock and the bus clock
-- clock-names: Should be "phy_ref_clk" for the reference clock and "apb_pclk"
-  for the bus clock.
+- clocks: Phandle and clock specifiers for each entry in clock-names, in the
+  same order. See ../clock/clock-bindings.txt.
+- clock-names: May contain any/all of the following depending on the IP
+  configuration, in any order:
+  - "tx"
+    The EQOS transmit path clock. The HW signal name is clk_tx_i.
+    In some configurations (e.g. GMII/RGMII), this clock also drives the PHY TX
+    path. In other configurations, other clocks (such as tx_125, rmii) may
+    drive the PHY TX path.
+  - "rx"
+    The EQOS receive path clock. The HW signal name is clk_rx_i.
+    In some configurations (e.g. GMII/RGMII), this clock is derived from the
+    PHY's RX clock output. In other configurations, other clocks (such as
+    rx_125, rmii) may drive the EQOS RX path.
+    In cases where the PHY clock is directly fed into the EQOS receive path
+    without intervening logic, the DT need not represent this clock, since it
+    is assumed to be fully under the control of the PHY device/driver. In
+    cases where SoC integration adds additional logic to this path, such as a
+    SW-controlled clock gate, this clock should be represented in DT.
+  - "slave_bus"
+    The CPU/slave-bus (CSR) interface clock. This applies to any bus type;
+    APB, AHB, AXI, etc. The HW signal name is hclk_i (AHB) or clk_csr_i (other
+    buses).
+  - "master_bus"
+    The master bus interface clock. Only required in configurations that use a
+    separate clock for the master and slave bus interfaces. The HW signal name
+    is hclk_i (AHB) or aclk_i (AXI).
+  - "ptp_ref"
+    The PTP reference clock. The HW signal name is clk_ptp_ref_i.
+  - "phy_ref_clk"
+    This clock is deprecated and should not be used by new compatible values.
+    It is equivalent to "tx".
+  - "apb_pclk"
+    This clock is deprecated and should not be used by new compatible values.
+    It is equivalent to "slave_bus".
+
+  Note: Support for additional IP configurations may require adding the
+  following clocks to this list in the future: clk_rx_125_i, clk_tx_125_i,
+  clk_pmarx_0_i, clk_pmarx1_i, clk_rmii_i, clk_revmii_rx_i, clk_revmii_tx_i.
+  Configurations exist where multiple similar clocks are used at once, e.g. all
+  of clk_rx_125_i, clk_pmarx_0_i, clk_pmarx1_i. For this reason it is best to
+  extend the binding with a separate clock-names entry for each of those RX
+  clocks, rather than repurposing the existing "rx" clock-names entry as a
+  generic/logical clock in a similar fashion to "master_bus" and "slave_bus".
+  This will allow easy support for configurations that support multiple PHY
+  interfaces using a mux, and hence need to have explicit control over
+  specific RX clocks.
+
+  The following compatible values require the following set of clocks:
+  - "nvidia,tegra186-eqos", "snps,dwc-qos-ethernet-4.10":
+    - "slave_bus"
+    - "master_bus"
+    - "rx"
+    - "tx"
+    - "ptp_ref"
+  - "axis,artpec6-eqos", "snps,dwc-qos-ethernet-4.10":
+    - "slave_bus"
+    - "master_bus"
+    - "tx"
+    - "ptp_ref"
+  - "snps,dwc-qos-ethernet-4.10" (deprecated):
+    - "phy_ref_clk"
+    - "apb_clk"
 - interrupt-parent: Should be the phandle for the interrupt controller
   that services interrupts for this device
 - interrupts: Should contain the core's combined interrupt signal
 - phy-mode: See ethernet.txt file in the same directory
+- resets: Phandle and reset specifiers for each entry in reset-names, in the
+  same order. See ../reset/reset.txt.
+- reset-names: May contain any/all of the following depending on the IP
+  configuration, in any order:
+  - "eqos". The reset to the entire module. The HW signal name is hreset_n
+    (AHB) or aresetn_i (AXI).
+
+  The following compatible values require the following set of resets:
+  (the reset properties may be omitted if empty)
+  - "nvidia,tegra186-eqos", "snps,dwc-qos-ethernet-4.10":
+    - "eqos".
+  - "axis,artpec6-eqos", "snps,dwc-qos-ethernet-4.10":
+    - None.
+  - "snps,dwc-qos-ethernet-4.10" (deprecated):
+    - None.
 
 Optional properties:
 - dma-coherent: Present if dma operations are coherent
 - mac-address: See ethernet.txt in the same directory
 - local-mac-address: See ethernet.txt in the same directory
+- phy-reset-gpios: Phandle and specifier for any GPIO used to reset the PHY.
+  See ../gpio/gpio.txt.
 - snps,en-lpi: If present it enables use of the AXI low-power interface
 - snps,write-requests: Number of write requests that the AXI port can issue.
   It depends on the SoC configuration.
@@ -52,6 +142,7 @@ ethernet2@40010000 {
 	reg = <0x40010000 0x4000>;
 	phy-handle = <&phy2>;
 	phy-mode = "gmii";
+	phy-reset-gpios = <&gpioctlr 43 GPIO_ACTIVE_LOW>;
 
 	snps,en-tx-lpi-clockgating;
 	snps,en-lpi;
diff --git a/dts/Bindings/net/stm32-dwmac.txt b/dts/Bindings/net/stm32-dwmac.txt
new file mode 100644
index 0000000000..c35afb7e95
--- /dev/null
+++ b/dts/Bindings/net/stm32-dwmac.txt
@@ -0,0 +1,32 @@
+STMicroelectronics STM32 / MCU DWMAC glue layer controller
+
+This file documents platform glue layer for stmmac.
+Please see stmmac.txt for the other unchanged properties.
+
+The device node has following properties.
+
+Required properties:
+- compatible:  Should be "st,stm32-dwmac" to select glue, and
+	       "snps,dwmac-3.50a" to select IP version.
+- clocks: Must contain a phandle for each entry in clock-names.
+- clock-names: Should be "stmmaceth" for the host clock.
+	       Should be "mac-clk-tx" for the MAC TX clock.
+	       Should be "mac-clk-rx" for the MAC RX clock.
+- st,syscon : Should be phandle/offset pair. The phandle to the syscon node which
+	      encompases the glue register, and the offset of the control register.
+Example:
+
+	ethernet@40028000 {
+		compatible = "st,stm32-dwmac", "snps,dwmac-3.50a";
+		status = "disabled";
+		reg = <0x40028000 0x8000>;
+		reg-names = "stmmaceth";
+		interrupts = <0 61 0>, <0 62 0>;
+		interrupt-names = "macirq", "eth_wake_irq";
+		clock-names = "stmmaceth", "mac-clk-tx", "mac-clk-rx";
+		clocks = <&rcc 0 25>, <&rcc 0 26>, <&rcc 0 27>;
+		st,syscon = <&syscfg 0x4>;
+		snps,pbl = <8>;
+		snps,mixed-burst;
+		dma-ranges;
+	};
diff --git a/dts/Bindings/net/wireless/esp,esp8089.txt b/dts/Bindings/net/wireless/esp,esp8089.txt
new file mode 100644
index 0000000000..19331bb4ff
--- /dev/null
+++ b/dts/Bindings/net/wireless/esp,esp8089.txt
@@ -0,0 +1,31 @@
+Espressif ESP8089 wireless SDIO devices
+
+This node provides properties for controlling the ESP8089 wireless device.
+The node is expected to be specified as a child node to the SDIO controller
+that connects the device to the system.
+
+Required properties:
+
+ - compatible : Should be "esp,esp8089".
+
+Optional properties:
+ - esp,crystal-26M-en: Integer value for the crystal_26M_en firmware parameter
+
+Example:
+
+&mmc1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	vmmc-supply = <&reg_dldo1>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+
+	esp8089: sdio_wifi@1 {
+		compatible = "esp,esp8089";
+		reg = <1>;
+		esp,crystal-26M-en = <2>;
+	};
+};
diff --git a/dts/Bindings/net/xilinx_gmii2rgmii.txt b/dts/Bindings/net/xilinx_gmii2rgmii.txt
new file mode 100644
index 0000000000..038dda48b8
--- /dev/null
+++ b/dts/Bindings/net/xilinx_gmii2rgmii.txt
@@ -0,0 +1,35 @@
+XILINX GMIITORGMII Converter Driver Device Tree Bindings
+--------------------------------------------------------
+
+The Gigabit Media Independent Interface (GMII) to Reduced Gigabit Media
+Independent Interface (RGMII) core provides the RGMII between RGMII-compliant
+Ethernet physical media devices (PHY) and the Gigabit Ethernet controller.
+This core can be used in all three modes of operation(10/100/1000 Mb/s).
+The Management Data Input/Output (MDIO) interface is used to configure the
+Speed of operation. This core can switch dynamically between the three
+Different speed modes by configuring the conveter register through mdio write.
+
+This converter sits between the ethernet MAC and the external phy.
+MAC <==> GMII2RGMII <==> RGMII_PHY
+
+For more details about mdio please refer phy.txt file in the same directory.
+
+Required properties:
+- compatible	: Should be "xlnx,gmii-to-rgmii-1.0"
+- reg		: The ID number for the phy, usually a small integer
+- phy-handle	: Should point to the external phy device.
+		  See ethernet.txt file in the same directory.
+
+Example:
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		phy: ethernet-phy@0 {
+			......
+		};
+		gmiitorgmii: gmiitorgmii@8 {
+			compatible = "xlnx,gmii-to-rgmii-1.0";
+			reg = <8>;
+			phy-handle = <&phy>;
+		};
+	};