dts: update to v3.18-rc1

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

8 files changed, 240 insertions, 3 deletions

diff --git a/dts/Bindings/pci/designware-pcie.txt b/dts/Bindings/pci/designware-pcie.txt
index ed0d9b9fff..9f4faa8e8d 100644
--- a/dts/Bindings/pci/designware-pcie.txt
+++ b/dts/Bindings/pci/designware-pcie.txt
@@ -23,3 +23,6 @@ Required properties:
 
 Optional properties:
 - reset-gpio: gpio pin number of power good signal
+- bus-range: PCI bus numbers covered (it is recommended for new devicetrees to
+  specify this property, to keep backwards compatibility a range of 0x00-0xff
+  is assumed if not present)
diff --git a/dts/Bindings/pci/fsl,imx6q-pcie.txt b/dts/Bindings/pci/fsl,imx6q-pcie.txt
index 9455fd0ec8..6fbba53a30 100644
--- a/dts/Bindings/pci/fsl,imx6q-pcie.txt
+++ b/dts/Bindings/pci/fsl,imx6q-pcie.txt
@@ -17,7 +17,9 @@ Example:
 
 	pcie@0x01000000 {
 		compatible = "fsl,imx6q-pcie", "snps,dw-pcie";
-		reg = <0x01ffc000 0x4000>;
+		reg = <0x01ffc000 0x04000>,
+		      <0x01f00000 0x80000>;
+		reg-names = "dbi", "config";
 		#address-cells = <3>;
 		#size-cells = <2>;
 		device_type = "pci";
diff --git a/dts/Bindings/pci/fsl,pci.txt b/dts/Bindings/pci/fsl,pci.txt
new file mode 100644
index 0000000000..d8ac4a768e
--- /dev/null
+++ b/dts/Bindings/pci/fsl,pci.txt
@@ -0,0 +1,27 @@
+* Bus Enumeration by Freescale PCI-X Agent
+
+Typically any Freescale PCI-X bridge hardware strapped into Agent mode
+is prevented from enumerating the bus. The PrPMC form-factor requires
+all mezzanines to be PCI-X Agents, but one per system may still
+enumerate the bus.
+
+The property defined below will allow a PCI-X bridge to be used for bus
+enumeration despite being strapped into Agent mode.
+
+Required properties:
+- fsl,pci-agent-force-enum : There is no value associated with this
+  property. The property itself is treated as a boolean.
+
+Example:
+
+	/* PCI-X bridge known to be PrPMC Monarch */
+	pci0: pci@ef008000 {
+		fsl,pci-agent-force-enum;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		compatible = "fsl,mpc8540-pcix", "fsl,mpc8540-pci";
+		device_type = "pci";
+		...
+		...
+	};
diff --git a/dts/Bindings/pci/host-generic-pci.txt b/dts/Bindings/pci/host-generic-pci.txt
index f0b0436807..cf3e205e0b 100644
--- a/dts/Bindings/pci/host-generic-pci.txt
+++ b/dts/Bindings/pci/host-generic-pci.txt
@@ -55,7 +55,7 @@ For CAM, this 24-bit offset is:
         cfg_offset(bus, device, function, register) =
                    bus << 16 | device << 11 | function << 8 | register
 
-Whilst ECAM extends this by 4 bits to accomodate 4k of function space:
+Whilst ECAM extends this by 4 bits to accommodate 4k of function space:
 
         cfg_offset(bus, device, function, register) =
                    bus << 20 | device << 15 | function << 12 | register
diff --git a/dts/Bindings/pci/nvidia,tegra20-pcie.txt b/dts/Bindings/pci/nvidia,tegra20-pcie.txt
index 0823362548..d763e047c6 100644
--- a/dts/Bindings/pci/nvidia,tegra20-pcie.txt
+++ b/dts/Bindings/pci/nvidia,tegra20-pcie.txt
@@ -1,7 +1,10 @@
 NVIDIA Tegra PCIe controller
 
 Required properties:
-- compatible: "nvidia,tegra20-pcie" or "nvidia,tegra30-pcie"
+- compatible: Must be one of:
+  - "nvidia,tegra20-pcie"
+  - "nvidia,tegra30-pcie"
+  - "nvidia,tegra124-pcie"
 - device_type: Must be "pci"
 - reg: A list of physical base address and length for each set of controller
   registers. Must contain an entry for each entry in the reg-names property.
@@ -57,6 +60,11 @@ Required properties:
   - afi
   - pcie_x
 
+Required properties on Tegra124 and later:
+- phys: Must contain an entry for each entry in phy-names.
+- phy-names: Must include the following entries:
+  - pcie
+
 Power supplies for Tegra20:
 - avdd-pex-supply: Power supply for analog PCIe logic. Must supply 1.05 V.
 - vdd-pex-supply: Power supply for digital PCIe I/O. Must supply 1.05 V.
@@ -84,6 +92,21 @@ Power supplies for Tegra30:
     - avdd-pexb-supply: Power supply for analog PCIe logic. Must supply 1.05 V.
     - vdd-pexb-supply: Power supply for digital PCIe I/O. Must supply 1.05 V.
 
+Power supplies for Tegra124:
+- Required:
+  - avddio-pex-supply: Power supply for analog PCIe logic. Must supply 1.05 V.
+  - dvddio-pex-supply: Power supply for digital PCIe I/O. Must supply 1.05 V.
+  - avdd-pex-pll-supply: Power supply for dedicated (internal) PCIe PLL. Must
+    supply 1.05 V.
+  - hvdd-pex-supply: High-voltage supply for PCIe I/O and PCIe output clocks.
+    Must supply 3.3 V.
+  - hvdd-pex-pll-e-supply: High-voltage supply for PLLE (shared with USB3).
+    Must supply 3.3 V.
+  - vddio-pex-ctl-supply: Power supply for PCIe control I/O partition. Must
+    supply 2.8-3.3 V.
+  - avdd-pll-erefe-supply: Power supply for PLLE (shared with USB3). Must
+    supply 1.05 V.
+
 Root ports are defined as subnodes of the PCIe controller node.
 
 Required properties:
diff --git a/dts/Bindings/pci/pci-keystone.txt b/dts/Bindings/pci/pci-keystone.txt
new file mode 100644
index 0000000000..54eae29381
--- /dev/null
+++ b/dts/Bindings/pci/pci-keystone.txt
@@ -0,0 +1,63 @@
+TI Keystone PCIe interface
+
+Keystone PCI host Controller is based on Designware PCI h/w version 3.65.
+It shares common functions with PCIe Designware core driver and inherit
+common properties defined in
+Documentation/devicetree/bindings/pci/designware-pci.txt
+
+Please refer to Documentation/devicetree/bindings/pci/designware-pci.txt
+for the details of Designware DT bindings.  Additional properties are
+described here as well as properties that are not applicable.
+
+Required Properties:-
+
+compatibility: "ti,keystone-pcie"
+reg:	index 1 is the base address and length of DW application registers.
+	index 2 is the base address and length of PCI device ID register.
+
+pcie_msi_intc : Interrupt controller device node for MSI IRQ chip
+	interrupt-cells: should be set to 1
+	interrupt-parent: Parent interrupt controller phandle
+	interrupts: GIC interrupt lines connected to PCI MSI interrupt lines
+
+ Example:
+	pcie_msi_intc: msi-interrupt-controller {
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			interrupt-parent = <&gic>;
+			interrupts = <GIC_SPI 30 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 31 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 32 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 33 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 34 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 35 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 36 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 37 IRQ_TYPE_EDGE_RISING>;
+	};
+
+pcie_intc: Interrupt controller device node for Legacy IRQ chip
+	interrupt-cells: should be set to 1
+	interrupt-parent: Parent interrupt controller phandle
+	interrupts: GIC interrupt lines connected to PCI Legacy interrupt lines
+
+ Example:
+	pcie_intc: legacy-interrupt-controller {
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>,
+			<GIC_SPI 27 IRQ_TYPE_EDGE_RISING>,
+			<GIC_SPI 28 IRQ_TYPE_EDGE_RISING>,
+			<GIC_SPI 29 IRQ_TYPE_EDGE_RISING>;
+	};
+
+Optional properties:-
+	phys: phandle to Generic Keystone SerDes phy for PCI
+	phy-names: name of the Generic Keystine SerDes phy for PCI
+	  - If boot loader already does PCI link establishment, then phys and
+	    phy-names shouldn't be present.
+
+Designware DT Properties not applicable for Keystone PCI
+
+1. pcie_bus clock-names not used.  Instead, a phandle to phys is used.
+
diff --git a/dts/Bindings/pci/xgene-pci.txt b/dts/Bindings/pci/xgene-pci.txt
new file mode 100644
index 0000000000..1070b068c7
--- /dev/null
+++ b/dts/Bindings/pci/xgene-pci.txt
@@ -0,0 +1,57 @@
+* AppliedMicro X-Gene PCIe interface
+
+Required properties:
+- device_type: set to "pci"
+- compatible: should contain "apm,xgene-pcie" to identify the core.
+- reg: A list of physical base address and length for each set of controller
+       registers. Must contain an entry for each entry in the reg-names
+       property.
+- reg-names: Must include the following entries:
+  "csr": controller configuration registers.
+  "cfg": pcie configuration space registers.
+- #address-cells: set to <3>
+- #size-cells: set to <2>
+- ranges: ranges for the outbound memory, I/O regions.
+- dma-ranges: ranges for the inbound memory regions.
+- #interrupt-cells: set to <1>
+- interrupt-map-mask and interrupt-map: standard PCI properties
+	to define the mapping of the PCIe interface to interrupt
+	numbers.
+- clocks: from common clock binding: handle to pci clock.
+
+Optional properties:
+- status: Either "ok" or "disabled".
+- dma-coherent: Present if dma operations are coherent
+
+Example:
+
+SoC specific DT Entry:
+
+	pcie0: pcie@1f2b0000 {
+		status = "disabled";
+		device_type = "pci";
+		compatible = "apm,xgene-storm-pcie", "apm,xgene-pcie";
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		reg = < 0x00 0x1f2b0000 0x0 0x00010000   /* Controller registers */
+			0xe0 0xd0000000 0x0 0x00040000>; /* PCI config space */
+		reg-names = "csr", "cfg";
+		ranges = <0x01000000 0x00 0x00000000 0xe0 0x10000000 0x00 0x00010000   /* io */
+			  0x02000000 0x00 0x80000000 0xe1 0x80000000 0x00 0x80000000>; /* mem */
+		dma-ranges = <0x42000000 0x80 0x00000000 0x80 0x00000000 0x00 0x80000000
+			      0x42000000 0x00 0x00000000 0x00 0x00000000 0x80 0x00000000>;
+		interrupt-map-mask = <0x0 0x0 0x0 0x7>;
+		interrupt-map = <0x0 0x0 0x0 0x1 &gic 0x0 0xc2 0x1
+				 0x0 0x0 0x0 0x2 &gic 0x0 0xc3 0x1
+				 0x0 0x0 0x0 0x3 &gic 0x0 0xc4 0x1
+				 0x0 0x0 0x0 0x4 &gic 0x0 0xc5 0x1>;
+		dma-coherent;
+		clocks = <&pcie0clk 0>;
+	};
+
+
+Board specific DT Entry:
+	&pcie0 {
+		status = "ok";
+	};
diff --git a/dts/Bindings/pci/xilinx-pcie.txt b/dts/Bindings/pci/xilinx-pcie.txt
new file mode 100644
index 0000000000..3e2c88d97a
--- /dev/null
+++ b/dts/Bindings/pci/xilinx-pcie.txt
@@ -0,0 +1,62 @@
+* Xilinx AXI PCIe Root Port Bridge DT description
+
+Required properties:
+- #address-cells: Address representation for root ports, set to <3>
+- #size-cells: Size representation for root ports, set to <2>
+- #interrupt-cells: specifies the number of cells needed to encode an
+	interrupt source. The value must be 1.
+- compatible: Should contain "xlnx,axi-pcie-host-1.00.a"
+- reg: Should contain AXI PCIe registers location and length
+- device_type: must be "pci"
+- interrupts: Should contain AXI PCIe interrupt
+- interrupt-map-mask,
+  interrupt-map: standard PCI properties to define the mapping of the
+	PCI interface to interrupt numbers.
+- ranges: ranges for the PCI memory regions (I/O space region is not
+	supported by hardware)
+	Please refer to the standard PCI bus binding document for a more
+	detailed explanation
+
+Optional properties:
+- bus-range: PCI bus numbers covered
+
+Interrupt controller child node
++++++++++++++++++++++++++++++++
+Required properties:
+- interrupt-controller: identifies the node as an interrupt controller
+- #address-cells: specifies the number of cells needed to encode an
+	address. The value must be 0.
+- #interrupt-cells: specifies the number of cells needed to encode an
+	interrupt source. The value must be 1.
+
+NOTE:
+The core provides a single interrupt for both INTx/MSI messages. So,
+created a interrupt controller node to support 'interrupt-map' DT
+functionality.  The driver will create an IRQ domain for this map, decode
+the four INTx interrupts in ISR and route them to this domain.
+
+
+Example:
+++++++++
+
+	pci_express: axi-pcie@50000000 {
+		#address-cells = <3>;
+		#size-cells = <2>;
+		#interrupt-cells = <1>;
+		compatible = "xlnx,axi-pcie-host-1.00.a";
+		reg = < 0x50000000 0x10000000 >;
+		device_type = "pci";
+		interrupts = < 0 52 4 >;
+		interrupt-map-mask = <0 0 0 7>;
+		interrupt-map = <0 0 0 1 &pcie_intc 1>,
+				<0 0 0 2 &pcie_intc 2>,
+				<0 0 0 3 &pcie_intc 3>,
+				<0 0 0 4 &pcie_intc 4>;
+		ranges = < 0x02000000 0 0x60000000 0x60000000 0 0x10000000 >;
+
+		pcie_intc: interrupt-controller {
+			interrupt-controller;
+			#address-cells = <0>;
+			#interrupt-cells = <1>;
+		}
+	};