dts: update to v6.0-rc1

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

11 files changed, 949 insertions, 337 deletions

diff --git a/dts/Bindings/pci/fsl,imx6q-pcie.yaml b/dts/Bindings/pci/fsl,imx6q-pcie.yaml
index 252e5b72ae..376e739bca 100644
--- a/dts/Bindings/pci/fsl,imx6q-pcie.yaml
+++ b/dts/Bindings/pci/fsl,imx6q-pcie.yaml
@@ -144,6 +144,7 @@ properties:
     description: If present then the reset sequence using the GPIO
       specified in the "reset-gpio" property is reversed (H=reset state,
       L=operation state) (optional required).
+    type: boolean
 
   vpcie-supply:
     description: Should specify the regulator in charge of PCIe port power.
diff --git a/dts/Bindings/pci/host-generic-pci.yaml b/dts/Bindings/pci/host-generic-pci.yaml
index 6bcaa8f2c3..d25423aa71 100644
--- a/dts/Bindings/pci/host-generic-pci.yaml
+++ b/dts/Bindings/pci/host-generic-pci.yaml
@@ -106,6 +106,9 @@ properties:
     maxItems: 3
 
   dma-coherent: true
+  iommu-map: true
+  iommu-map-mask: true
+  msi-parent: true
 
 required:
   - compatible
diff --git a/dts/Bindings/pci/mediatek-pcie.txt b/dts/Bindings/pci/mediatek-pcie.txt
index 57ae734622..6842275222 100644
--- a/dts/Bindings/pci/mediatek-pcie.txt
+++ b/dts/Bindings/pci/mediatek-pcie.txt
@@ -7,6 +7,7 @@ Required properties:
 	"mediatek,mt7622-pcie"
 	"mediatek,mt7623-pcie"
 	"mediatek,mt7629-pcie"
+	"airoha,en7523-pcie"
 - device_type: Must be "pci"
 - reg: Base addresses and lengths of the root ports.
 - reg-names: Names of the above areas to use during resource lookup.
diff --git a/dts/Bindings/pci/nvidia,tegra194-pcie-ep.yaml b/dts/Bindings/pci/nvidia,tegra194-pcie-ep.yaml
new file mode 100644
index 0000000000..a24fb8307d
--- /dev/null
+++ b/dts/Bindings/pci/nvidia,tegra194-pcie-ep.yaml
@@ -0,0 +1,319 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pci/nvidia,tegra194-pcie-ep.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NVIDIA Tegra194 (and later) PCIe Endpoint controller (Synopsys DesignWare Core based)
+
+maintainers:
+  - Thierry Reding <thierry.reding@gmail.com>
+  - Jon Hunter <jonathanh@nvidia.com>
+  - Vidya Sagar <vidyas@nvidia.com>
+
+description: |
+  This PCIe controller is based on the Synopsys DesignWare PCIe IP and thus
+  inherits all the common properties defined in snps,dw-pcie-ep.yaml.  Some
+  of the controller instances are dual mode; they can work either in Root
+  Port mode or Endpoint mode but one at a time.
+
+  On Tegra194, controllers C0, C4 and C5 support Endpoint mode.
+  On Tegra234, controllers C5, C6, C7 and C10 support Endpoint mode.
+
+  Note: On Tegra194's P2972-0000 platform, only C5 controller can be enabled to
+  operate in the Endpoint mode because of the way the platform is designed.
+
+properties:
+  compatible:
+    enum:
+      - nvidia,tegra194-pcie-ep
+      - nvidia,tegra234-pcie-ep
+
+  reg:
+    items:
+      - description: controller's application logic registers
+      - description: iATU and DMA registers. This is where the iATU (internal
+          Address Translation Unit) registers of the PCIe core are made
+          available for software access.
+      - description: aperture where the Root Port's own configuration
+          registers are available.
+      - description: aperture used to map the remote Root Complex address space
+
+  reg-names:
+    items:
+      - const: appl
+      - const: atu_dma
+      - const: dbi
+      - const: addr_space
+
+  interrupts:
+    items:
+      - description: controller interrupt
+
+  interrupt-names:
+    items:
+      - const: intr
+
+  clocks:
+    items:
+      - description: module clock
+
+  clock-names:
+    items:
+      - const: core
+
+  resets:
+    items:
+      - description: APB bus interface reset
+      - description: module reset
+
+  reset-names:
+    items:
+      - const: apb
+      - const: core
+
+  reset-gpios:
+    description: Must contain a phandle to a GPIO controller followed by GPIO
+      that is being used as PERST input signal. Please refer to pci.txt.
+
+  phys:
+    minItems: 1
+    maxItems: 8
+
+  phy-names:
+    minItems: 1
+    items:
+      - const: p2u-0
+      - const: p2u-1
+      - const: p2u-2
+      - const: p2u-3
+      - const: p2u-4
+      - const: p2u-5
+      - const: p2u-6
+      - const: p2u-7
+
+  power-domains:
+    maxItems: 1
+    description: |
+      A phandle to the node that controls power to the respective PCIe
+      controller and a specifier name for the PCIe controller.
+
+      Tegra194 specifiers are defined in "include/dt-bindings/power/tegra194-powergate.h"
+      Tegra234 specifiers are defined in "include/dt-bindings/power/tegra234-powergate.h"
+
+  interconnects:
+    items:
+      - description: memory read client
+      - description: memory write client
+
+  interconnect-names:
+    items:
+      - const: dma-mem # read
+      - const: write
+
+  dma-coherent: true
+
+  nvidia,bpmp:
+    $ref: /schemas/types.yaml#/definitions/phandle-array
+    description: |
+      Must contain a pair of phandles to BPMP controller node followed by
+      controller ID. Following are the controller IDs for each controller:
+
+      Tegra194
+
+        0: C0
+        1: C1
+        2: C2
+        3: C3
+        4: C4
+        5: C5
+
+      Tegra234
+
+        0 : C0
+        1 : C1
+        2 : C2
+        3 : C3
+        4 : C4
+        5 : C5
+        6 : C6
+        7 : C7
+        8 : C8
+        9 : C9
+        10: C10
+
+    items:
+      - items:
+          - description: phandle to BPMP controller node
+          - description: PCIe controller ID
+            maximum: 10
+
+  nvidia,aspm-cmrt-us:
+    description: Common Mode Restore Time for proper operation of ASPM to be
+      specified in microseconds
+
+  nvidia,aspm-pwr-on-t-us:
+    description: Power On time for proper operation of ASPM to be specified in
+      microseconds
+
+  nvidia,aspm-l0s-entrance-latency-us:
+    description: ASPM L0s entrance latency to be specified in microseconds
+
+  vddio-pex-ctl-supply:
+    description: A phandle to the regulator supply for PCIe side band signals
+
+  nvidia,refclk-select-gpios:
+    maxItems: 1
+    description: GPIO used to enable REFCLK to controller from the host
+
+  nvidia,enable-ext-refclk:
+    description: |
+      This boolean property needs to be present if the controller is configured
+      to receive Reference Clock from the host.
+      NOTE: This is applicable only for Tegra234.
+
+    $ref: /schemas/types.yaml#/definitions/flag
+
+  nvidia,enable-srns:
+    description: |
+      This boolean property needs to be present if the controller is
+      configured to operate in SRNS (Separate Reference Clocks with No
+      Spread-Spectrum Clocking).  NOTE: This is applicable only for
+      Tegra234.
+
+    $ref: /schemas/types.yaml#/definitions/flag
+
+allOf:
+  - $ref: /schemas/pci/snps,dw-pcie-ep.yaml#
+
+unevaluatedProperties: false
+
+required:
+  - interrupts
+  - interrupt-names
+  - clocks
+  - clock-names
+  - resets
+  - reset-names
+  - power-domains
+  - reset-gpios
+  - vddio-pex-ctl-supply
+  - num-lanes
+  - phys
+  - phy-names
+  - nvidia,bpmp
+
+examples:
+  - |
+    #include <dt-bindings/clock/tegra194-clock.h>
+    #include <dt-bindings/gpio/tegra194-gpio.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/power/tegra194-powergate.h>
+    #include <dt-bindings/reset/tegra194-reset.h>
+
+    bus@0 {
+        #address-cells = <2>;
+        #size-cells = <2>;
+        ranges = <0x0 0x0 0x0 0x8 0x0>;
+
+        pcie-ep@141a0000 {
+            compatible = "nvidia,tegra194-pcie-ep";
+            reg = <0x00 0x141a0000 0x0 0x00020000>, /* appl registers (128K) */
+                  <0x00 0x3a040000 0x0 0x00040000>, /* iATU_DMA reg space (256K)  */
+                  <0x00 0x3a080000 0x0 0x00040000>, /* DBI reg space (256K) */
+                  <0x1c 0x00000000 0x4 0x00000000>; /* Address Space (16G) */
+            reg-names = "appl", "atu_dma", "dbi", "addr_space";
+            interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>; /* controller interrupt */
+            interrupt-names = "intr";
+
+            clocks = <&bpmp TEGRA194_CLK_PEX1_CORE_5>;
+            clock-names = "core";
+
+            resets = <&bpmp TEGRA194_RESET_PEX1_CORE_5_APB>,
+                     <&bpmp TEGRA194_RESET_PEX1_CORE_5>;
+            reset-names = "apb", "core";
+
+            power-domains = <&bpmp TEGRA194_POWER_DOMAIN_PCIEX8A>;
+            pinctrl-names = "default";
+            pinctrl-0 = <&clkreq_c5_bi_dir_state>;
+
+            nvidia,bpmp = <&bpmp 5>;
+
+            nvidia,aspm-cmrt-us = <60>;
+            nvidia,aspm-pwr-on-t-us = <20>;
+            nvidia,aspm-l0s-entrance-latency-us = <3>;
+
+            vddio-pex-ctl-supply = <&vdd_1v8ao>;
+
+            reset-gpios = <&gpio TEGRA194_MAIN_GPIO(GG, 1) GPIO_ACTIVE_LOW>;
+
+            nvidia,refclk-select-gpios = <&gpio_aon TEGRA194_AON_GPIO(AA, 5)
+                                          GPIO_ACTIVE_HIGH>;
+
+            num-lanes = <8>;
+
+            phys = <&p2u_nvhs_0>, <&p2u_nvhs_1>, <&p2u_nvhs_2>,
+                   <&p2u_nvhs_3>, <&p2u_nvhs_4>, <&p2u_nvhs_5>,
+                   <&p2u_nvhs_6>, <&p2u_nvhs_7>;
+
+            phy-names = "p2u-0", "p2u-1", "p2u-2", "p2u-3", "p2u-4",
+                        "p2u-5", "p2u-6", "p2u-7";
+        };
+    };
+
+  - |
+    #include <dt-bindings/clock/tegra234-clock.h>
+    #include <dt-bindings/gpio/tegra234-gpio.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/power/tegra234-powergate.h>
+    #include <dt-bindings/reset/tegra234-reset.h>
+
+    bus@0 {
+        #address-cells = <2>;
+        #size-cells = <2>;
+        ranges = <0x0 0x0 0x0 0x8 0x0>;
+
+        pcie-ep@141a0000 {
+            compatible = "nvidia,tegra234-pcie-ep";
+            power-domains = <&bpmp TEGRA234_POWER_DOMAIN_PCIEX8A>;
+            reg = <0x00 0x141a0000 0x0 0x00020000>, /* appl registers (128K)      */
+                  <0x00 0x3a040000 0x0 0x00040000>, /* iATU_DMA reg space (256K)  */
+                  <0x00 0x3a080000 0x0 0x00040000>, /* DBI reg space (256K)       */
+                  <0x27 0x40000000 0x4 0x00000000>; /* Address Space (16G)        */
+            reg-names = "appl", "atu_dma", "dbi", "addr_space";
+
+            interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>; /* controller interrupt */
+            interrupt-names = "intr";
+
+            clocks = <&bpmp TEGRA234_CLK_PEX1_C5_CORE>;
+            clock-names = "core";
+
+            resets = <&bpmp TEGRA234_RESET_PEX1_CORE_5_APB>,
+                     <&bpmp TEGRA234_RESET_PEX1_CORE_5>;
+            reset-names = "apb", "core";
+
+            nvidia,bpmp = <&bpmp 5>;
+
+            nvidia,enable-ext-refclk;
+            nvidia,aspm-cmrt-us = <60>;
+            nvidia,aspm-pwr-on-t-us = <20>;
+            nvidia,aspm-l0s-entrance-latency-us = <3>;
+
+            vddio-pex-ctl-supply = <&p3701_vdd_1v8_ls>;
+
+            reset-gpios = <&gpio TEGRA234_MAIN_GPIO(AF, 1) GPIO_ACTIVE_LOW>;
+
+            nvidia,refclk-select-gpios = <&gpio_aon
+                                          TEGRA234_AON_GPIO(AA, 4)
+                                          GPIO_ACTIVE_HIGH>;
+
+            num-lanes = <8>;
+
+            phys = <&p2u_nvhs_0>, <&p2u_nvhs_1>, <&p2u_nvhs_2>,
+                   <&p2u_nvhs_3>, <&p2u_nvhs_4>, <&p2u_nvhs_5>,
+                   <&p2u_nvhs_6>, <&p2u_nvhs_7>;
+
+            phy-names = "p2u-0", "p2u-1", "p2u-2", "p2u-3", "p2u-4",
+                        "p2u-5", "p2u-6", "p2u-7";
+        };
+    };
diff --git a/dts/Bindings/pci/nvidia,tegra194-pcie.txt b/dts/Bindings/pci/nvidia,tegra194-pcie.txt
deleted file mode 100644
index 8e4f9bfb31..0000000000
--- a/dts/Bindings/pci/nvidia,tegra194-pcie.txt
+++ /dev/null
@@ -1,245 +0,0 @@
-NVIDIA Tegra PCIe controller (Synopsys DesignWare Core based)
-
-This PCIe controller is based on the Synopsis Designware PCIe IP
-and thus inherits all the common properties defined in snps,dw-pcie.yaml and
-snps,dw-pcie-ep.yaml.
-Some of the controller instances are dual mode where in they can work either
-in root port mode or endpoint mode but one at a time.
-
-Required properties:
-- power-domains: A phandle to the node that controls power to the respective
-  PCIe controller and a specifier name for the PCIe controller. Following are
-  the specifiers for the different PCIe controllers
-    TEGRA194_POWER_DOMAIN_PCIEX8B: C0
-    TEGRA194_POWER_DOMAIN_PCIEX1A: C1
-    TEGRA194_POWER_DOMAIN_PCIEX1A: C2
-    TEGRA194_POWER_DOMAIN_PCIEX1A: C3
-    TEGRA194_POWER_DOMAIN_PCIEX4A: C4
-    TEGRA194_POWER_DOMAIN_PCIEX8A: C5
-  these specifiers are defined in
-  "include/dt-bindings/power/tegra194-powergate.h" file.
-- reg: A list of physical base address and length pairs for each set of
-  controller registers. Must contain an entry for each entry in the reg-names
-  property.
-- reg-names: Must include the following entries:
-  "appl": Controller's application logic registers
-  "config": As per the definition in snps,dw-pcie.yaml
-  "atu_dma": iATU and DMA registers. This is where the iATU (internal Address
-             Translation Unit) registers of the PCIe core are made available
-             for SW access.
-  "dbi": The aperture where root port's own configuration registers are
-         available
-- interrupts: A list of interrupt outputs of the controller. Must contain an
-  entry for each entry in the interrupt-names property.
-- interrupt-names: Must include the following entries:
-  "intr": The Tegra interrupt that is asserted for controller interrupts
-- clocks: Must contain an entry for each entry in clock-names.
-  See ../clocks/clock-bindings.txt for details.
-- clock-names: Must include the following entries:
-  - core
-- resets: Must contain an entry for each entry in reset-names.
-  See ../reset/reset.txt for details.
-- reset-names: Must include the following entries:
-  - apb
-  - core
-- phys: Must contain a phandle to P2U PHY for each entry in phy-names.
-- phy-names: Must include an entry for each active lane.
-  "p2u-N": where N ranges from 0 to one less than the total number of lanes
-- nvidia,bpmp: Must contain a pair of phandle to BPMP controller node followed
-  by controller-id. Following are the controller ids for each controller.
-    0: C0
-    1: C1
-    2: C2
-    3: C3
-    4: C4
-    5: C5
-- vddio-pex-ctl-supply: Regulator supply for PCIe side band signals
-
-RC mode:
-- compatible: Tegra19x must contain  "nvidia,tegra194-pcie"
-- device_type: Must be "pci" for RC mode
-- interrupt-names: Must include the following entries:
-  "msi": The Tegra interrupt that is asserted when an MSI is received
-- bus-range: Range of bus numbers associated with this controller
-- #address-cells: Address representation for root ports (must be 3)
-  - cell 0 specifies the bus and device numbers of the root port:
-    [23:16]: bus number
-    [15:11]: device number
-  - cell 1 denotes the upper 32 address bits and should be 0
-  - cell 2 contains the lower 32 address bits and is used to translate to the
-    CPU address space
-- #size-cells: Size representation for root ports (must be 2)
-- ranges: Describes the translation of addresses for root ports and standard
-  PCI regions. The entries must be 7 cells each, where the first three cells
-  correspond to the address as described for the #address-cells property
-  above, the fourth and fifth cells are for the physical CPU address to
-  translate to and the sixth and seventh cells are as described for the
-  #size-cells property above.
-  - Entries setup the mapping for the standard I/O, memory and
-    prefetchable PCI regions. The first cell determines the type of region
-    that is setup:
-    - 0x81000000: I/O memory region
-    - 0x82000000: non-prefetchable memory region
-    - 0xc2000000: prefetchable memory region
-  Please refer to the standard PCI bus binding document for a more detailed
-  explanation.
-- #interrupt-cells: Size representation for interrupts (must be 1)
-- interrupt-map-mask and interrupt-map: Standard PCI IRQ mapping properties
-  Please refer to the standard PCI bus binding document for a more detailed
-  explanation.
-
-EP mode:
-In Tegra194, Only controllers C0, C4 & C5 support EP mode.
-- compatible: Tegra19x must contain "nvidia,tegra194-pcie-ep"
-- reg-names: Must include the following entries:
-  "addr_space": Used to map remote RC address space
-- reset-gpios: Must contain a phandle to a GPIO controller followed by
-  GPIO that is being used as PERST input signal. Please refer to pci.txt
-  document.
-
-Optional properties:
-- pinctrl-names: A list of pinctrl state names.
-  It is mandatory for C5 controller and optional for other controllers.
-  - "default": Configures PCIe I/O for proper operation.
-- pinctrl-0: phandle for the 'default' state of pin configuration.
-  It is mandatory for C5 controller and optional for other controllers.
-- supports-clkreq: Refer to Documentation/devicetree/bindings/pci/pci.txt
-- nvidia,update-fc-fixup: This is a boolean property and needs to be present to
-    improve performance when a platform is designed in such a way that it
-    satisfies at least one of the following conditions thereby enabling root
-    port to exchange optimum number of FC (Flow Control) credits with
-    downstream devices
-    1. If C0/C4/C5 run at x1/x2 link widths (irrespective of speed and MPS)
-    2. If C0/C1/C2/C3/C4/C5 operate at their respective max link widths and
-       a) speed is Gen-2 and MPS is 256B
-       b) speed is >= Gen-3 with any MPS
-- nvidia,aspm-cmrt-us: Common Mode Restore Time for proper operation of ASPM
-   to be specified in microseconds
-- nvidia,aspm-pwr-on-t-us: Power On time for proper operation of ASPM to be
-   specified in microseconds
-- nvidia,aspm-l0s-entrance-latency-us: ASPM L0s entrance latency to be
-   specified in microseconds
-
-RC mode:
-- vpcie3v3-supply: A phandle to the regulator node that supplies 3.3V to the slot
-  if the platform has one such slot. (Ex:- x16 slot owned by C5 controller
-  in p2972-0000 platform).
-- vpcie12v-supply: A phandle to the regulator node that supplies 12V to the slot
-  if the platform has one such slot. (Ex:- x16 slot owned by C5 controller
-  in p2972-0000 platform).
-
-EP mode:
-- nvidia,refclk-select-gpios: Must contain a phandle to a GPIO controller
-  followed by GPIO that is being used to enable REFCLK to controller from host
-
-NOTE:- On Tegra194's P2972-0000 platform, only C5 controller can be enabled to
-operate in the endpoint mode because of the way the platform is designed.
-
-Examples:
-=========
-
-Tegra194 RC mode:
------------------
-
-	pcie@14180000 {
-		compatible = "nvidia,tegra194-pcie";
-		power-domains = <&bpmp TEGRA194_POWER_DOMAIN_PCIEX8B>;
-		reg = <0x00 0x14180000 0x0 0x00020000   /* appl registers (128K)      */
-		       0x00 0x38000000 0x0 0x00040000   /* configuration space (256K) */
-		       0x00 0x38040000 0x0 0x00040000>; /* iATU_DMA reg space (256K)  */
-		reg-names = "appl", "config", "atu_dma";
-
-		#address-cells = <3>;
-		#size-cells = <2>;
-		device_type = "pci";
-		num-lanes = <8>;
-		linux,pci-domain = <0>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&pex_rst_c5_out_state>, <&clkreq_c5_bi_dir_state>;
-
-		clocks = <&bpmp TEGRA194_CLK_PEX0_CORE_0>;
-		clock-names = "core";
-
-		resets = <&bpmp TEGRA194_RESET_PEX0_CORE_0_APB>,
-			 <&bpmp TEGRA194_RESET_PEX0_CORE_0>;
-		reset-names = "apb", "core";
-
-		interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,	/* controller interrupt */
-			     <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;	/* MSI interrupt */
-		interrupt-names = "intr", "msi";
-
-		#interrupt-cells = <1>;
-		interrupt-map-mask = <0 0 0 0>;
-		interrupt-map = <0 0 0 0 &gic GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
-
-		nvidia,bpmp = <&bpmp 0>;
-
-		supports-clkreq;
-		nvidia,aspm-cmrt-us = <60>;
-		nvidia,aspm-pwr-on-t-us = <20>;
-		nvidia,aspm-l0s-entrance-latency-us = <3>;
-
-		bus-range = <0x0 0xff>;
-		ranges = <0x81000000 0x0  0x38100000 0x0  0x38100000 0x0 0x00100000    /* downstream I/O (1MB) */
-			  0x82000000 0x0  0x38200000 0x0  0x38200000 0x0 0x01E00000    /* non-prefetchable memory (30MB) */
-			  0xc2000000 0x18 0x00000000 0x18 0x00000000 0x4 0x00000000>;  /* prefetchable memory (16GB) */
-
-		vddio-pex-ctl-supply = <&vdd_1v8ao>;
-		vpcie3v3-supply = <&vdd_3v3_pcie>;
-		vpcie12v-supply = <&vdd_12v_pcie>;
-
-		phys = <&p2u_hsio_2>, <&p2u_hsio_3>, <&p2u_hsio_4>,
-		       <&p2u_hsio_5>;
-		phy-names = "p2u-0", "p2u-1", "p2u-2", "p2u-3";
-	};
-
-Tegra194 EP mode:
------------------
-
-	pcie-ep@141a0000 {
-		compatible = "nvidia,tegra194-pcie-ep", "snps,dw-pcie-ep";
-		power-domains = <&bpmp TEGRA194_POWER_DOMAIN_PCIEX8A>;
-		reg = <0x00 0x141a0000 0x0 0x00020000   /* appl registers (128K)      */
-		       0x00 0x3a040000 0x0 0x00040000   /* iATU_DMA reg space (256K)  */
-		       0x00 0x3a080000 0x0 0x00040000   /* DBI reg space (256K)       */
-		       0x1c 0x00000000 0x4 0x00000000>; /* Address Space (16G)        */
-		reg-names = "appl", "atu_dma", "dbi", "addr_space";
-
-		num-lanes = <8>;
-		num-ib-windows = <2>;
-		num-ob-windows = <8>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&clkreq_c5_bi_dir_state>;
-
-		clocks = <&bpmp TEGRA194_CLK_PEX1_CORE_5>;
-		clock-names = "core";
-
-		resets = <&bpmp TEGRA194_RESET_PEX1_CORE_5_APB>,
-			 <&bpmp TEGRA194_RESET_PEX1_CORE_5>;
-		reset-names = "apb", "core";
-
-		interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;	/* controller interrupt */
-		interrupt-names = "intr";
-
-		nvidia,bpmp = <&bpmp 5>;
-
-		nvidia,aspm-cmrt-us = <60>;
-		nvidia,aspm-pwr-on-t-us = <20>;
-		nvidia,aspm-l0s-entrance-latency-us = <3>;
-
-		vddio-pex-ctl-supply = <&vdd_1v8ao>;
-
-		reset-gpios = <&gpio TEGRA194_MAIN_GPIO(GG, 1) GPIO_ACTIVE_LOW>;
-
-		nvidia,refclk-select-gpios = <&gpio_aon TEGRA194_AON_GPIO(AA, 5)
-					      GPIO_ACTIVE_HIGH>;
-
-		phys = <&p2u_nvhs_0>, <&p2u_nvhs_1>, <&p2u_nvhs_2>,
-		       <&p2u_nvhs_3>, <&p2u_nvhs_4>, <&p2u_nvhs_5>,
-		       <&p2u_nvhs_6>, <&p2u_nvhs_7>;
-
-		phy-names = "p2u-0", "p2u-1", "p2u-2", "p2u-3", "p2u-4",
-			    "p2u-5", "p2u-6", "p2u-7";
-	};
diff --git a/dts/Bindings/pci/nvidia,tegra194-pcie.yaml b/dts/Bindings/pci/nvidia,tegra194-pcie.yaml
new file mode 100644
index 0000000000..75da3e8eec
--- /dev/null
+++ b/dts/Bindings/pci/nvidia,tegra194-pcie.yaml
@@ -0,0 +1,350 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pci/nvidia,tegra194-pcie.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NVIDIA Tegra194 (and later) PCIe controller (Synopsys DesignWare Core based)
+
+maintainers:
+  - Thierry Reding <thierry.reding@gmail.com>
+  - Jon Hunter <jonathanh@nvidia.com>
+  - Vidya Sagar <vidyas@nvidia.com>
+
+description: |
+  This PCIe controller is based on the Synopsys DesignWare PCIe IP and thus
+  inherits all the common properties defined in snps,dw-pcie.yaml. Some of
+  the controller instances are dual mode where in they can work either in
+  Root Port mode or Endpoint mode but one at a time.
+
+  See nvidia,tegra194-pcie-ep.yaml for details on the Endpoint mode device
+  tree bindings.
+
+properties:
+  compatible:
+    enum:
+      - nvidia,tegra194-pcie
+      - nvidia,tegra234-pcie
+
+  reg:
+    items:
+      - description: controller's application logic registers
+      - description: configuration registers
+      - description: iATU and DMA registers. This is where the iATU (internal
+          Address Translation Unit) registers of the PCIe core are made
+          available for software access.
+      - description: aperture where the Root Port's own configuration
+          registers are available.
+
+  reg-names:
+    items:
+      - const: appl
+      - const: config
+      - const: atu_dma
+      - const: dbi
+
+  interrupts:
+    items:
+      - description: controller interrupt
+      - description: MSI interrupt
+
+  interrupt-names:
+    items:
+      - const: intr
+      - const: msi
+
+  clocks:
+    items:
+      - description: module clock
+
+  clock-names:
+    items:
+      - const: core
+
+  resets:
+    items:
+      - description: APB bus interface reset
+      - description: module reset
+
+  reset-names:
+    items:
+      - const: apb
+      - const: core
+
+  phys:
+    minItems: 1
+    maxItems: 8
+
+  phy-names:
+    minItems: 1
+    items:
+      - const: p2u-0
+      - const: p2u-1
+      - const: p2u-2
+      - const: p2u-3
+      - const: p2u-4
+      - const: p2u-5
+      - const: p2u-6
+      - const: p2u-7
+
+  power-domains:
+    maxItems: 1
+    description: |
+      A phandle to the node that controls power to the respective PCIe
+      controller and a specifier name for the PCIe controller.
+
+      Tegra194 specifiers defined in "include/dt-bindings/power/tegra194-powergate.h"
+      Tegra234 specifiers defined in "include/dt-bindings/power/tegra234-powergate.h"
+
+  interconnects:
+    items:
+      - description: memory read client
+      - description: memory write client
+
+  interconnect-names:
+    items:
+      - const: dma-mem # read
+      - const: write
+
+  dma-coherent: true
+
+  nvidia,bpmp:
+    $ref: /schemas/types.yaml#/definitions/phandle-array
+    description: |
+      Must contain a pair of phandles to BPMP controller node followed by
+      controller ID. Following are the controller IDs for each controller:
+
+      Tegra194
+
+        0: C0
+        1: C1
+        2: C2
+        3: C3
+        4: C4
+        5: C5
+
+      Tegra234
+
+        0 : C0
+        1 : C1
+        2 : C2
+        3 : C3
+        4 : C4
+        5 : C5
+        6 : C6
+        7 : C7
+        8 : C8
+        9 : C9
+        10: C10
+
+    items:
+      - items:
+          - description: phandle to BPMP controller node
+          - description: PCIe controller ID
+            maximum: 10
+
+  nvidia,update-fc-fixup:
+    description: |
+      This is a boolean property and needs to be present to improve performance
+      when a platform is designed in such a way that it satisfies at least one
+      of the following conditions thereby enabling Root Port to exchange
+      optimum number of FC (Flow Control) credits with downstream devices:
+
+      NOTE: This is applicable only for Tegra194.
+
+        1. If C0/C4/C5 run at x1/x2 link widths (irrespective of speed and MPS)
+        2. If C0/C1/C2/C3/C4/C5 operate at their respective max link widths and
+          a) speed is Gen-2 and MPS is 256B
+          b) speed is >= Gen-3 with any MPS
+
+    $ref: /schemas/types.yaml#/definitions/flag
+
+  nvidia,aspm-cmrt-us:
+    description: Common Mode Restore Time for proper operation of ASPM to be
+      specified in microseconds
+
+  nvidia,aspm-pwr-on-t-us:
+    description: Power On time for proper operation of ASPM to be specified in
+      microseconds
+
+  nvidia,aspm-l0s-entrance-latency-us:
+    description: ASPM L0s entrance latency to be specified in microseconds
+
+  vddio-pex-ctl-supply:
+    description: A phandle to the regulator supply for PCIe side band signals.
+
+  vpcie3v3-supply:
+    description: A phandle to the regulator node that supplies 3.3V to the slot
+      if the platform has one such slot, e.g., x16 slot owned by C5 controller
+      in p2972-0000 platform.
+
+  vpcie12v-supply:
+    description: A phandle to the regulator node that supplies 12V to the slot
+      if the platform has one such slot, e.g., x16 slot owned by C5 controller
+      in p2972-0000 platform.
+
+  nvidia,enable-srns:
+    description: |
+      This boolean property needs to be present if the controller is
+      configured to operate in SRNS (Separate Reference Clocks with No
+      Spread-Spectrum Clocking).  NOTE: This is applicable only for
+      Tegra234.
+
+    $ref: /schemas/types.yaml#/definitions/flag
+
+  nvidia,enable-ext-refclk:
+    description: |
+      This boolean property needs to be present if the controller is
+      configured to use the reference clocking coming in from an external
+      clock source instead of using the internal clock source.
+
+    $ref: /schemas/types.yaml#/definitions/flag
+
+allOf:
+  - $ref: /schemas/pci/snps,dw-pcie.yaml#
+
+unevaluatedProperties: false
+
+required:
+  - interrupts
+  - interrupt-names
+  - interrupt-map
+  - interrupt-map-mask
+  - clocks
+  - clock-names
+  - resets
+  - reset-names
+  - power-domains
+  - vddio-pex-ctl-supply
+  - num-lanes
+  - phys
+  - phy-names
+  - nvidia,bpmp
+
+examples:
+  - |
+    #include <dt-bindings/clock/tegra194-clock.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/power/tegra194-powergate.h>
+    #include <dt-bindings/reset/tegra194-reset.h>
+
+    bus@0 {
+        #address-cells = <2>;
+        #size-cells = <2>;
+        ranges = <0x0 0x0 0x0 0x8 0x0>;
+
+        pcie@14180000 {
+            compatible = "nvidia,tegra194-pcie";
+            power-domains = <&bpmp TEGRA194_POWER_DOMAIN_PCIEX8B>;
+            reg = <0x0 0x14180000 0x0 0x00020000>, /* appl registers (128K)      */
+                  <0x0 0x38000000 0x0 0x00040000>, /* configuration space (256K) */
+                  <0x0 0x38040000 0x0 0x00040000>, /* iATU_DMA reg space (256K)  */
+                  <0x0 0x38080000 0x0 0x00040000>; /* DBI reg space (256K)       */
+            reg-names = "appl", "config", "atu_dma", "dbi";
+
+            #address-cells = <3>;
+            #size-cells = <2>;
+            device_type = "pci";
+            num-lanes = <8>;
+            linux,pci-domain = <0>;
+
+            pinctrl-names = "default";
+            pinctrl-0 = <&pex_rst_c5_out_state>, <&clkreq_c5_bi_dir_state>;
+
+            clocks = <&bpmp TEGRA194_CLK_PEX0_CORE_0>;
+            clock-names = "core";
+
+            resets = <&bpmp TEGRA194_RESET_PEX0_CORE_0_APB>,
+                     <&bpmp TEGRA194_RESET_PEX0_CORE_0>;
+            reset-names = "apb", "core";
+
+            interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>, /* controller interrupt */
+                         <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */
+            interrupt-names = "intr", "msi";
+
+            #interrupt-cells = <1>;
+            interrupt-map-mask = <0 0 0 0>;
+            interrupt-map = <0 0 0 0 &gic GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
+
+            nvidia,bpmp = <&bpmp 0>;
+
+            supports-clkreq;
+            nvidia,aspm-cmrt-us = <60>;
+            nvidia,aspm-pwr-on-t-us = <20>;
+            nvidia,aspm-l0s-entrance-latency-us = <3>;
+
+            bus-range = <0x0 0xff>;
+            ranges = <0x81000000 0x0  0x38100000 0x0  0x38100000 0x0 0x00100000>, /* downstream I/O */
+                     <0x82000000 0x0  0x38200000 0x0  0x38200000 0x0 0x01e00000>, /* non-prefetch memory */
+                     <0xc2000000 0x18 0x00000000 0x18 0x00000000 0x4 0x00000000>; /* prefetchable memory */
+
+            vddio-pex-ctl-supply = <&vdd_1v8ao>;
+            vpcie3v3-supply = <&vdd_3v3_pcie>;
+            vpcie12v-supply = <&vdd_12v_pcie>;
+
+            phys = <&p2u_hsio_2>, <&p2u_hsio_3>, <&p2u_hsio_4>,
+                   <&p2u_hsio_5>;
+            phy-names = "p2u-0", "p2u-1", "p2u-2", "p2u-3";
+        };
+    };
+
+  - |
+    #include <dt-bindings/clock/tegra234-clock.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/power/tegra234-powergate.h>
+    #include <dt-bindings/reset/tegra234-reset.h>
+
+    bus@0 {
+        #address-cells = <2>;
+        #size-cells = <2>;
+        ranges = <0x0 0x0 0x0 0x8 0x0>;
+
+        pcie@14160000 {
+            compatible = "nvidia,tegra234-pcie";
+            power-domains = <&bpmp TEGRA234_POWER_DOMAIN_PCIEX4BB>;
+            reg = <0x00 0x14160000 0x0 0x00020000>, /* appl registers (128K)      */
+                  <0x00 0x36000000 0x0 0x00040000>, /* configuration space (256K) */
+                  <0x00 0x36040000 0x0 0x00040000>, /* iATU_DMA reg space (256K)  */
+                  <0x00 0x36080000 0x0 0x00040000>; /* DBI reg space (256K)       */
+            reg-names = "appl", "config", "atu_dma", "dbi";
+
+            #address-cells = <3>;
+            #size-cells = <2>;
+            device_type = "pci";
+            num-lanes = <4>;
+            num-viewport = <8>;
+            linux,pci-domain = <4>;
+
+            clocks = <&bpmp TEGRA234_CLK_PEX0_C4_CORE>;
+            clock-names = "core";
+
+            resets = <&bpmp TEGRA234_RESET_PEX0_CORE_4_APB>,
+                     <&bpmp TEGRA234_RESET_PEX0_CORE_4>;
+            reset-names = "apb", "core";
+
+            interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>, /* controller interrupt */
+                         <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */
+            interrupt-names = "intr", "msi";
+
+            #interrupt-cells = <1>;
+            interrupt-map-mask = <0 0 0 0>;
+            interrupt-map = <0 0 0 0 &gic GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
+
+            nvidia,bpmp = <&bpmp 4>;
+
+            nvidia,aspm-cmrt-us = <60>;
+            nvidia,aspm-pwr-on-t-us = <20>;
+            nvidia,aspm-l0s-entrance-latency-us = <3>;
+
+            bus-range = <0x0 0xff>;
+            ranges = <0x43000000 0x21 0x40000000 0x21 0x40000000 0x2 0xe8000000>, /* prefetchable */
+                     <0x02000000 0x0  0x40000000 0x24 0x28000000 0x0 0x08000000>, /* non-prefetchable */
+                     <0x01000000 0x0  0x36100000 0x00 0x36100000 0x0 0x00100000>; /* downstream I/O */
+
+            vddio-pex-ctl-supply = <&p3701_vdd_AO_1v8>;
+
+            phys = <&p2u_hsio_4>, <&p2u_hsio_5>, <&p2u_hsio_6>,
+                   <&p2u_hsio_7>;
+            phy-names = "p2u-0", "p2u-1", "p2u-2", "p2u-3";
+        };
+    };
diff --git a/dts/Bindings/pci/pci-rcar-gen2.txt b/dts/Bindings/pci/pci-rcar-gen2.txt
deleted file mode 100644
index aeba38f0a3..0000000000
--- a/dts/Bindings/pci/pci-rcar-gen2.txt
+++ /dev/null
@@ -1,84 +0,0 @@
-Renesas AHB to PCI bridge
--------------------------
-
-This is the bridge used internally to connect the USB controllers to the
-AHB. There is one bridge instance per USB port connected to the internal
-OHCI and EHCI controllers.
-
-Required properties:
-- compatible: "renesas,pci-r8a7742" for the R8A7742 SoC;
-	      "renesas,pci-r8a7743" for the R8A7743 SoC;
-	      "renesas,pci-r8a7744" for the R8A7744 SoC;
-	      "renesas,pci-r8a7745" for the R8A7745 SoC;
-	      "renesas,pci-r8a7790" for the R8A7790 SoC;
-	      "renesas,pci-r8a7791" for the R8A7791 SoC;
-	      "renesas,pci-r8a7793" for the R8A7793 SoC;
-	      "renesas,pci-r8a7794" for the R8A7794 SoC;
-	      "renesas,pci-rcar-gen2" for a generic R-Car Gen2 or
-				      RZ/G1 compatible device.
-
-
-	      When compatible with the generic version, nodes must list the
-	      SoC-specific version corresponding to the platform first
-	      followed by the generic version.
-
-- reg:	A list of physical regions to access the device: the first is
-	the operational registers for the OHCI/EHCI controllers and the
-	second is for the bridge configuration and control registers.
-- interrupts: interrupt for the device.
-- clocks: The reference to the device clock.
-- bus-range: The PCI bus number range; as this is a single bus, the range
-	     should be specified as the same value twice.
-- #address-cells: must be 3.
-- #size-cells: must be 2.
-- #interrupt-cells: must be 1.
-- interrupt-map: standard property used to define the mapping of the PCI
-  interrupts to the GIC interrupts.
-- interrupt-map-mask: standard property that helps to define the interrupt
-  mapping.
-
-Optional properties:
-- dma-ranges: a single range for the inbound memory region. If not supplied,
-  defaults to 1GiB at 0x40000000. Note there are hardware restrictions on the
-  allowed combinations of address and size.
-
-Example SoC configuration:
-
-	pci0: pci@ee090000  {
-		compatible = "renesas,pci-r8a7790", "renesas,pci-rcar-gen2";
-		clocks = <&mstp7_clks R8A7790_CLK_EHCI>;
-		reg = <0x0 0xee090000 0x0 0xc00>,
-		      <0x0 0xee080000 0x0 0x1100>;
-		interrupts = <0 108 IRQ_TYPE_LEVEL_HIGH>;
-		status = "disabled";
-
-		bus-range = <0 0>;
-		#address-cells = <3>;
-		#size-cells = <2>;
-		#interrupt-cells = <1>;
-		dma-ranges = <0x42000000 0 0x40000000 0 0x40000000 0 0x40000000>;
-		interrupt-map-mask = <0xff00 0 0 0x7>;
-		interrupt-map = <0x0000 0 0 1 &gic 0 108 IRQ_TYPE_LEVEL_HIGH
-				 0x0800 0 0 1 &gic 0 108 IRQ_TYPE_LEVEL_HIGH
-				 0x1000 0 0 2 &gic 0 108 IRQ_TYPE_LEVEL_HIGH>;
-
-		usb@1,0 {
-			reg = <0x800 0 0 0 0>;
-			phys = <&usb0 0>;
-			phy-names = "usb";
-		};
-
-		usb@2,0 {
-			reg = <0x1000 0 0 0 0>;
-			phys = <&usb0 0>;
-			phy-names = "usb";
-		};
-	};
-
-Example board setup:
-
-&pci0 {
-	status = "okay";
-	pinctrl-0 = <&usb0_pins>;
-	pinctrl-names = "default";
-};
diff --git a/dts/Bindings/pci/qcom,pcie.yaml b/dts/Bindings/pci/qcom,pcie.yaml
index 0b69b12b84..7d29e2a451 100644
--- a/dts/Bindings/pci/qcom,pcie.yaml
+++ b/dts/Bindings/pci/qcom,pcie.yaml
@@ -11,7 +11,7 @@ maintainers:
   - Stanimir Varbanov <svarbanov@mm-sol.com>
 
 description: |
-  Qualcomm PCIe root complex controller is bansed on the Synopsys DesignWare
+  Qualcomm PCIe root complex controller is based on the Synopsys DesignWare
   PCIe IP.
 
 properties:
@@ -43,11 +43,12 @@ properties:
     maxItems: 5
 
   interrupts:
-    maxItems: 1
+    minItems: 1
+    maxItems: 8
 
   interrupt-names:
-    items:
-      - const: msi
+    minItems: 1
+    maxItems: 8
 
   # Common definitions for clocks, clock-names and reset.
   # Platform constraints are described later.
@@ -614,7 +615,7 @@ allOf:
   - if:
       not:
         properties:
-          compatibles:
+          compatible:
             contains:
               enum:
                 - qcom,pcie-msm8996
@@ -623,6 +624,50 @@ allOf:
         - resets
         - reset-names
 
+    # Newer chipsets support either 1 or 8 MSI vectors
+    # On older chipsets it's always 1 MSI vector
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - qcom,pcie-msm8996
+              - qcom,pcie-sc7280
+              - qcom,pcie-sc8180x
+              - qcom,pcie-sdm845
+              - qcom,pcie-sm8150
+              - qcom,pcie-sm8250
+              - qcom,pcie-sm8450-pcie0
+              - qcom,pcie-sm8450-pcie1
+    then:
+      oneOf:
+        - properties:
+            interrupts:
+              maxItems: 1
+            interrupt-names:
+              items:
+                - const: msi
+        - properties:
+            interrupts:
+              minItems: 8
+            interrupt-names:
+              items:
+                - const: msi0
+                - const: msi1
+                - const: msi2
+                - const: msi3
+                - const: msi4
+                - const: msi5
+                - const: msi6
+                - const: msi7
+    else:
+      properties:
+        interrupts:
+          maxItems: 1
+        interrupt-names:
+          items:
+            - const: msi
+
 unevaluatedProperties: false
 
 examples:
diff --git a/dts/Bindings/pci/renesas,pci-rcar-gen2.yaml b/dts/Bindings/pci/renesas,pci-rcar-gen2.yaml
new file mode 100644
index 0000000000..0f18cceba3
--- /dev/null
+++ b/dts/Bindings/pci/renesas,pci-rcar-gen2.yaml
@@ -0,0 +1,186 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pci/renesas,pci-rcar-gen2.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Renesas AHB to PCI bridge
+
+maintainers:
+  - Marek Vasut <marek.vasut+renesas@gmail.com>
+  - Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
+
+description: |
+  This is the bridge used internally to connect the USB controllers to the
+  AHB. There is one bridge instance per USB port connected to the internal
+  OHCI and EHCI controllers.
+
+properties:
+  compatible:
+    oneOf:
+      - items:
+          - enum:
+              - renesas,pci-r8a7742      # RZ/G1H
+              - renesas,pci-r8a7743      # RZ/G1M
+              - renesas,pci-r8a7744      # RZ/G1N
+              - renesas,pci-r8a7745      # RZ/G1E
+              - renesas,pci-r8a7790      # R-Car H2
+              - renesas,pci-r8a7791      # R-Car M2-W
+              - renesas,pci-r8a7793      # R-Car M2-N
+              - renesas,pci-r8a7794      # R-Car E2
+          - const: renesas,pci-rcar-gen2 # R-Car Gen2 and RZ/G1
+      - items:
+          - enum:
+              - renesas,pci-r9a06g032     # RZ/N1D
+          - const: renesas,pci-rzn1       # RZ/N1
+
+  reg:
+    items:
+      - description: Operational registers for the OHCI/EHCI controllers.
+      - description: Bridge configuration and control registers.
+
+  interrupts:
+    maxItems: 1
+
+  clocks: true
+
+  clock-names: true
+
+  resets:
+    maxItems: 1
+
+  power-domains:
+    maxItems: 1
+
+  bus-range:
+    description: |
+      The PCI bus number range; as this is a single bus, the range
+      should be specified as the same value twice.
+
+  dma-ranges:
+    description: |
+      A single range for the inbound memory region. If not supplied,
+      defaults to 1GiB at 0x40000000. Note there are hardware restrictions on
+      the allowed combinations of address and size.
+    maxItems: 1
+
+patternProperties:
+  'usb@[0-1],0':
+    type: object
+
+    description:
+      This a USB controller PCI device
+
+    properties:
+      reg:
+        description:
+          Identify the correct bus, device and function number in the
+          form <bdf 0 0 0 0>.
+
+        items:
+          minItems: 5
+          maxItems: 5
+
+      phys:
+        description:
+          Reference to the USB phy
+        maxItems: 1
+
+      phy-names:
+        maxItems: 1
+
+    required:
+      - reg
+      - phys
+      - phy-names
+
+    unevaluatedProperties: false
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - interrupt-map
+  - interrupt-map-mask
+  - clocks
+  - power-domains
+  - bus-range
+  - "#address-cells"
+  - "#size-cells"
+  - "#interrupt-cells"
+
+allOf:
+  - $ref: /schemas/pci/pci-bus.yaml#
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - renesas,pci-rzn1
+    then:
+      properties:
+        clocks:
+          items:
+            - description: Internal bus clock (AHB) for HOST
+            - description: Internal bus clock (AHB) Power Management
+            - description: PCI clock for USB subsystem
+        clock-names:
+          items:
+            - const: hclkh
+            - const: hclkpm
+            - const: pciclk
+      required:
+        - clock-names
+    else:
+      properties:
+        clocks:
+          items:
+            - description: Device clock
+        clock-names:
+          items:
+            - const: pclk
+      required:
+        - resets
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/clock/r8a7790-cpg-mssr.h>
+    #include <dt-bindings/power/r8a7790-sysc.h>
+
+    pci@ee090000  {
+        compatible = "renesas,pci-r8a7790", "renesas,pci-rcar-gen2";
+        device_type = "pci";
+        reg = <0xee090000 0xc00>,
+              <0xee080000 0x1100>;
+        clocks = <&cpg CPG_MOD 703>;
+        power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
+        resets = <&cpg 703>;
+        interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+
+        bus-range = <0 0>;
+        #address-cells = <3>;
+        #size-cells = <2>;
+        #interrupt-cells = <1>;
+        ranges = <0x02000000 0 0xee080000 0xee080000 0 0x00010000>;
+        dma-ranges = <0x42000000 0 0x40000000 0x40000000 0 0x40000000>;
+        interrupt-map-mask = <0xf800 0 0 0x7>;
+        interrupt-map = <0x0000 0 0 1 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
+                        <0x0800 0 0 1 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
+                        <0x1000 0 0 2 &gic GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+
+        usb@1,0 {
+            reg = <0x800 0 0 0 0>;
+            phys = <&usb0 0>;
+            phy-names = "usb";
+        };
+
+        usb@2,0 {
+            reg = <0x1000 0 0 0 0>;
+            phys = <&usb0 0>;
+            phy-names = "usb";
+        };
+    };
diff --git a/dts/Bindings/pci/snps,dw-pcie.yaml b/dts/Bindings/pci/snps,dw-pcie.yaml
index c90e5e2d25..7287d395e1 100644
--- a/dts/Bindings/pci/snps,dw-pcie.yaml
+++ b/dts/Bindings/pci/snps,dw-pcie.yaml
@@ -34,8 +34,8 @@ properties:
     minItems: 2
     maxItems: 5
     items:
-      enum: [ dbi, dbi2, config, atu, app, elbi, mgmt, ctrl, parf, cfg, link,
-              ulreg, smu, mpu, apb, phy ]
+      enum: [ dbi, dbi2, config, atu, atu_dma, app, appl, elbi, mgmt, ctrl,
+              parf, cfg, link, ulreg, smu, mpu, apb, phy ]
 
   num-lanes:
     description: |
diff --git a/dts/Bindings/pci/xilinx-versal-cpm.yaml b/dts/Bindings/pci/xilinx-versal-cpm.yaml
index cca395317a..24ddc2855b 100644
--- a/dts/Bindings/pci/xilinx-versal-cpm.yaml
+++ b/dts/Bindings/pci/xilinx-versal-cpm.yaml
@@ -14,17 +14,23 @@ allOf:
 
 properties:
   compatible:
-    const: xlnx,versal-cpm-host-1.00
+    enum:
+      - xlnx,versal-cpm-host-1.00
+      - xlnx,versal-cpm5-host
 
   reg:
     items:
       - description: CPM system level control and status registers.
       - description: Configuration space region and bridge registers.
+      - description: CPM5 control and status registers.
+    minItems: 2
 
   reg-names:
     items:
       - const: cpm_slcr
       - const: cfg
+      - const: cpm_csr
+    minItems: 2
 
   interrupts:
     maxItems: 1
@@ -95,4 +101,34 @@ examples:
                                interrupt-controller;
                        };
                };
+
+               cpm5_pcie: pcie@fcdd0000 {
+                       compatible = "xlnx,versal-cpm5-host";
+                       device_type = "pci";
+                       #address-cells = <3>;
+                       #interrupt-cells = <1>;
+                       #size-cells = <2>;
+                       interrupts = <0 72 4>;
+                       interrupt-parent = <&gic>;
+                       interrupt-map-mask = <0 0 0 7>;
+                       interrupt-map = <0 0 0 1 &pcie_intc_1 0>,
+                                       <0 0 0 2 &pcie_intc_1 1>,
+                                       <0 0 0 3 &pcie_intc_1 2>,
+                                       <0 0 0 4 &pcie_intc_1 3>;
+                       bus-range = <0x00 0xff>;
+                       ranges = <0x02000000 0x0 0xe0000000 0x0 0xe0000000 0x0 0x10000000>,
+                                <0x43000000 0x80 0x00000000 0x80 0x00000000 0x0 0x80000000>;
+                       msi-map = <0x0 &its_gic 0x0 0x10000>;
+                       reg = <0x00 0xfcdd0000 0x00 0x1000>,
+                             <0x06 0x00000000 0x00 0x1000000>,
+                             <0x00 0xfce20000 0x00 0x1000000>;
+                       reg-names = "cpm_slcr", "cfg", "cpm_csr";
+
+                       pcie_intc_1: interrupt-controller {
+                               #address-cells = <0>;
+                               #interrupt-cells = <1>;
+                               interrupt-controller;
+                       };
+               };
+
     };