dts: update to v4.13-rc2

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>

8 files changed, 159 insertions, 12 deletions

diff --git a/dts/Bindings/phy/bcm-ns-usb3-phy.txt b/dts/Bindings/phy/bcm-ns-usb3-phy.txt
index 09aeba9453..32f0572603 100644
--- a/dts/Bindings/phy/bcm-ns-usb3-phy.txt
+++ b/dts/Bindings/phy/bcm-ns-usb3-phy.txt
@@ -3,9 +3,10 @@ Driver for Broadcom Northstar USB 3.0 PHY
 Required properties:
 
 - compatible: one of: "brcm,ns-ax-usb3-phy", "brcm,ns-bx-usb3-phy".
-- reg: register mappings for DMP (Device Management Plugin) and ChipCommon B
-       MMI.
-- reg-names: "dmp" and "ccb-mii"
+- reg: address of MDIO bus device
+- usb3-dmp-syscon: phandle to syscon with DMP (Device Management Plugin)
+		   registers
+- #phy-cells: must be 0
 
 Initialization of USB 3.0 PHY depends on Northstar version. There are currently
 three known series: Ax, Bx and Cx.
@@ -15,9 +16,19 @@ Known B1: BCM4707 rev 6
 Known C0: BCM47094 rev 0
 
 Example:
-	usb3-phy {
-		compatible = "brcm,ns-ax-usb3-phy";
-		reg = <0x18105000 0x1000>, <0x18003000 0x1000>;
-		reg-names = "dmp", "ccb-mii";
-		#phy-cells = <0>;
+	mdio: mdio@0 {
+		reg = <0x0>;
+		#size-cells = <1>;
+		#address-cells = <0>;
+
+		usb3-phy@10 {
+			compatible = "brcm,ns-ax-usb3-phy";
+			reg = <0x10>;
+			usb3-dmp-syscon = <&usb3_dmp>;
+			#phy-cells = <0>;
+		};
+	};
+
+	usb3_dmp: syscon@18105000 {
+		reg = <0x18105000 0x1000>;
 	};
diff --git a/dts/Bindings/phy/brcm,ns2-drd-phy.txt b/dts/Bindings/phy/brcm,ns2-drd-phy.txt
new file mode 100644
index 0000000000..04f063aa78
--- /dev/null
+++ b/dts/Bindings/phy/brcm,ns2-drd-phy.txt
@@ -0,0 +1,30 @@
+BROADCOM NORTHSTAR2 USB2 (DUAL ROLE DEVICE) PHY
+
+Required properties:
+ - compatible: brcm,ns2-drd-phy
+ - reg: offset and length of the NS2 PHY related registers.
+ - reg-names
+   The below registers must be provided.
+   icfg - for DRD ICFG configurations
+   rst-ctrl - for DRD IDM reset
+   crmu-ctrl - for CRMU core vdd, PHY and PHY PLL reset
+   usb2-strap - for port over current polarity reversal
+ - #phy-cells: Must be 0. No args required.
+ - vbus-gpios: vbus gpio binding
+ - id-gpios: id gpio binding
+
+Refer to phy/phy-bindings.txt for the generic PHY binding properties
+
+Example:
+	usbdrd_phy: phy@66000960 {
+			#phy-cells = <0>;
+			compatible = "brcm,ns2-drd-phy";
+			reg = <0x66000960 0x24>,
+			      <0x67012800 0x4>,
+			      <0x6501d148 0x4>,
+			      <0x664d0700 0x4>;
+			reg-names = "icfg", "rst-ctrl",
+				    "crmu-ctrl", "usb2-strap";
+			id-gpios = <&gpio_g 30 0>;
+			vbus-gpios = <&gpio_g 31 0>;
+	};
diff --git a/dts/Bindings/phy/brcm-sata-phy.txt b/dts/Bindings/phy/brcm-sata-phy.txt
index 6ccce09d8b..97977cd29a 100644
--- a/dts/Bindings/phy/brcm-sata-phy.txt
+++ b/dts/Bindings/phy/brcm-sata-phy.txt
@@ -7,12 +7,13 @@ Required properties:
      "brcm,iproc-ns2-sata-phy"
      "brcm,iproc-nsp-sata-phy"
      "brcm,phy-sata3"
+     "brcm,iproc-sr-sata-phy"
 - address-cells: should be 1
 - size-cells: should be 0
 - reg: register ranges for the PHY PCB interface
 - reg-names: should be "phy" and "phy-ctrl"
      The "phy-ctrl" registers are only required for
-     "brcm,iproc-ns2-sata-phy".
+     "brcm,iproc-ns2-sata-phy" and "brcm,iproc-sr-sata-phy".
 
 Sub-nodes:
   Each port's PHY should be represented as a sub-node.
@@ -23,8 +24,8 @@ Sub-nodes required properties:
 
 Sub-nodes optional properties:
 - brcm,enable-ssc: use spread spectrum clocking (SSC) on this port
-     This property is not applicable for "brcm,iproc-ns2-sata-phy" and
-     "brcm,iproc-nsp-sata-phy".
+     This property is not applicable for "brcm,iproc-ns2-sata-phy",
+     "brcm,iproc-nsp-sata-phy" and "brcm,iproc-sr-sata-phy".
 
 Example:
 	sata-phy@f0458100 {
diff --git a/dts/Bindings/phy/meson-gxl-usb2-phy.txt b/dts/Bindings/phy/meson-gxl-usb2-phy.txt
new file mode 100644
index 0000000000..a105494a0f
--- /dev/null
+++ b/dts/Bindings/phy/meson-gxl-usb2-phy.txt
@@ -0,0 +1,17 @@
+* Amlogic Meson GXL and GXM USB2 PHY binding
+
+Required properties:
+- compatible:	Should be "amlogic,meson-gxl-usb2-phy"
+- reg:		The base address and length of the registers
+- #phys-cells:	must be 0 (see phy-bindings.txt in this directory)
+
+Optional properties:
+- phy-supply:	see phy-bindings.txt in this directory
+
+
+Example:
+	usb2_phy0: phy@78000 {
+		compatible = "amlogic,meson-gxl-usb2-phy";
+		#phy-cells = <0>;
+		reg = <0x0 0x78000 0x0 0x20>;
+	};
diff --git a/dts/Bindings/phy/meson8b-usb2-phy.txt b/dts/Bindings/phy/meson8b-usb2-phy.txt
index 5fa73b9d20..d81d73aea6 100644
--- a/dts/Bindings/phy/meson8b-usb2-phy.txt
+++ b/dts/Bindings/phy/meson8b-usb2-phy.txt
@@ -1,7 +1,8 @@
-* Amlogic Meson8b and GXBB USB2 PHY
+* Amlogic Meson8, Meson8b and GXBB USB2 PHY
 
 Required properties:
 - compatible:	Depending on the platform this should be one of:
+	"amlogic,meson8-usb2-phy"
 	"amlogic,meson8b-usb2-phy"
 	"amlogic,meson-gxbb-usb2-phy"
 - reg:		The base address and length of the registers
diff --git a/dts/Bindings/phy/phy-cpcap-usb.txt b/dts/Bindings/phy/phy-cpcap-usb.txt
new file mode 100644
index 0000000000..2eb9b2b690
--- /dev/null
+++ b/dts/Bindings/phy/phy-cpcap-usb.txt
@@ -0,0 +1,40 @@
+Motorola CPCAP PMIC USB PHY binding
+
+Required properties:
+compatible: Shall be either "motorola,cpcap-usb-phy" or
+	    "motorola,mapphone-cpcap-usb-phy"
+#phy-cells: Shall be 0
+interrupts: CPCAP PMIC interrupts used by the USB PHY
+interrupt-names: Interrupt names
+io-channels: IIO ADC channels used by the USB PHY
+io-channel-names: IIO ADC channel names
+vusb-supply: Regulator for the PHY
+
+Optional properties:
+pinctrl: Optional alternate pin modes for the PHY
+pinctrl-names: Names for optional pin modes
+mode-gpios: Optional GPIOs for configuring alternate modes
+
+Example:
+cpcap_usb2_phy: phy {
+	compatible = "motorola,mapphone-cpcap-usb-phy";
+	pinctrl-0 = <&usb_gpio_mux_sel1 &usb_gpio_mux_sel2>;
+	pinctrl-1 = <&usb_ulpi_pins>;
+	pinctrl-2 = <&usb_utmi_pins>;
+	pinctrl-3 = <&uart3_pins>;
+	pinctrl-names = "default", "ulpi", "utmi", "uart";
+	#phy-cells = <0>;
+	interrupts-extended = <
+		&cpcap 15 0 &cpcap 14 0 &cpcap 28 0 &cpcap 19 0
+		&cpcap 18 0 &cpcap 17 0 &cpcap 16 0 &cpcap 49 0
+		&cpcap 48 1
+	>;
+	interrupt-names =
+		"id_ground", "id_float", "se0conn", "vbusvld",
+		"sessvld", "sessend", "se1", "dm", "dp";
+	mode-gpios = <&gpio2 28 GPIO_ACTIVE_HIGH
+		      &gpio1 0 GPIO_ACTIVE_HIGH>;
+	io-channels = <&cpcap_adc 2>, <&cpcap_adc 7>;
+	io-channel-names = "vbus", "id";
+	vusb-supply = <&vusb>;
+};
diff --git a/dts/Bindings/phy/phy-rockchip-inno-usb2.txt b/dts/Bindings/phy/phy-rockchip-inno-usb2.txt
index e71a8d23f4..84d59b0db8 100644
--- a/dts/Bindings/phy/phy-rockchip-inno-usb2.txt
+++ b/dts/Bindings/phy/phy-rockchip-inno-usb2.txt
@@ -2,6 +2,7 @@ ROCKCHIP USB2.0 PHY WITH INNO IP BLOCK
 
 Required properties (phy (parent) node):
  - compatible : should be one of the listed compatibles:
+	* "rockchip,rk3228-usb2phy"
 	* "rockchip,rk3328-usb2phy"
 	* "rockchip,rk3366-usb2phy"
 	* "rockchip,rk3399-usb2phy"
diff --git a/dts/Bindings/phy/rcar-gen3-phy-usb3.txt b/dts/Bindings/phy/rcar-gen3-phy-usb3.txt
new file mode 100644
index 0000000000..f94cea48f6
--- /dev/null
+++ b/dts/Bindings/phy/rcar-gen3-phy-usb3.txt
@@ -0,0 +1,46 @@
+* Renesas R-Car generation 3 USB 3.0 PHY
+
+This file provides information on what the device node for the R-Car generation
+3 USB 3.0 PHY contains.
+If you want to enable spread spectrum clock (ssc), you should use USB_EXTAL
+instead of USB3_CLK. However, if you don't want to these features, you don't
+need this driver.
+
+Required properties:
+- compatible: "renesas,r8a7795-usb3-phy" if the device is a part of an R8A7795
+	      SoC.
+	      "renesas,r8a7796-usb3-phy" if the device is a part of an R8A7796
+	      SoC.
+	      "renesas,rcar-gen3-usb3-phy" for a generic R-Car Gen3 compatible
+	      device.
+
+	      When compatible with the generic version, nodes must list the
+	      SoC-specific version corresponding to the platform first
+	      followed by the generic version.
+
+- reg: offset and length of the USB 3.0 PHY register block.
+- clocks: A list of phandles and clock-specifier pairs.
+- clock-names: Name of the clocks.
+  - The funcional clock must be "usb3-if".
+  - The usb3's external clock must be "usb3s_clk".
+  - The usb2's external clock must be "usb_extal". If you want to use the ssc,
+    the clock-frequency must not be 0.
+- #phy-cells: see phy-bindings.txt in the same directory, must be <0>.
+
+Optional properties:
+- renesas,ssc-range: Enable/disable spread spectrum clock (ssc) by using
+		     the following values as u32:
+			- 0 (or the property doesn't exist): disable the ssc
+			- 4980: enable the ssc as -4980 ppm
+			- 4492: enable the ssc as -4492 ppm
+			- 4003: enable the ssc as -4003 ppm
+
+Example (R-Car H3):
+
+	usb-phy@e65ee000 {
+		compatible = "renesas,r8a7795-usb3-phy",
+			     "renesas,rcar-gen3-usb3-phy";
+		reg = <0 0xe65ee000 0 0x90>;
+		clocks = <&cpg CPG_MOD 328>, <&usb3s0_clk>, <&usb_extal>;
+		clock-names = "usb3-if", "usb3s_clk", "usb_extal";
+	};