dts: update to v4.14-rc1

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

5 files changed, 59 insertions, 11 deletions

diff --git a/dts/Bindings/power/supply/act8945a-charger.txt b/dts/Bindings/power/supply/act8945a-charger.txt
index de78d761ce..b86ecada4f 100644
--- a/dts/Bindings/power/supply/act8945a-charger.txt
+++ b/dts/Bindings/power/supply/act8945a-charger.txt
@@ -29,7 +29,6 @@ Example:
 	pmic@5b {
 		compatible = "active-semi,act8945a";
 		reg = <0x5b>;
-		status = "okay";
 
 		charger {
 			compatible = "active-semi,act8945a-charger";
@@ -43,6 +42,5 @@ Example:
 			active-semi,input-voltage-threshold-microvolt = <6600>;
 			active-semi,precondition-timeout = <40>;
 			active-semi,total-timeout = <3>;
-			status = "okay";
 		};
 	};
diff --git a/dts/Bindings/power/supply/bq24190.txt b/dts/Bindings/power/supply/bq24190.txt
new file mode 100644
index 0000000000..9e517d3070
--- /dev/null
+++ b/dts/Bindings/power/supply/bq24190.txt
@@ -0,0 +1,51 @@
+TI BQ24190 Li-Ion Battery Charger
+
+Required properties:
+- compatible: contains one of the following:
+    * "ti,bq24190"
+    * "ti,bq24192i"
+- reg: integer, I2C address of the charger.
+- interrupts[-extended]: configuration for charger INT pin.
+
+Optional properties:
+- monitored-battery: phandle of battery characteristics devicetree node
+  The charger uses the following battery properties:
+    + precharge-current-microamp: maximum charge current during precharge
+      phase (typically 20% of battery capacity).
+    + charge-term-current-microamp: a charge cycle terminates when the
+      battery voltage is above recharge threshold, and the current is below
+      this setting (typically 10% of battery capacity).
+  See also Documentation/devicetree/bindings/power/supply/battery.txt
+- ti,system-minimum-microvolt: when power is connected and the battery is below
+  minimum system voltage, the system will be regulated above this setting.
+
+Notes:
+- Some circuit boards wire the chip's "OTG" pin high (enabling 500mA default
+  charge current on USB SDP ports, among other features). To simulate this on
+  boards that wire the pin to a GPIO, set a gpio-hog.
+
+Example:
+
+	bat: battery {
+		compatible = "simple-battery";
+		precharge-current-microamp = <256000>;
+		charge-term-current-microamp = <128000>;
+		// etc.
+	};
+
+	bq24190: charger@6a {
+		compatible = "ti,bq24190";
+		reg = <0x6a>;
+		interrupts-extended = <&gpiochip 10 IRQ_TYPE_EDGE_FALLING>;
+		monitored-battery = <&bat>;
+		ti,system-minimum-microvolt = <3200000>;
+	};
+
+	&twl_gpio {
+		otg {
+			gpio-hog;
+			gpios = <6 0>;
+			output-high;
+			line-name = "otg-gpio";
+		};
+	};
diff --git a/dts/Bindings/power/supply/ltc2941.txt b/dts/Bindings/power/supply/ltc2941.txt
index a9d7aa6055..3b9ba147b0 100644
--- a/dts/Bindings/power/supply/ltc2941.txt
+++ b/dts/Bindings/power/supply/ltc2941.txt
@@ -1,13 +1,14 @@
-binding for LTC2941 and LTC2943 battery gauges
+binding for LTC2941, LTC2942, LTC2943 and LTC2944 battery gauges
 
-Both the LTC2941 and LTC2943 measure battery capacity.
-The LTC2943 is compatible with the LTC2941, it adds voltage and
-temperature monitoring, and uses a slightly different conversion
-formula for the charge counter.
+All chips measure battery capacity.
+The LTC2942 is pin compatible with the LTC2941, it adds voltage and
+temperature monitoring, and is runtime detected. LTC2943 and LTC2944
+is software compatible, uses a slightly different conversion formula
+for the charge counter and adds voltage, current and temperature monitoring.
 
 Required properties:
-- compatible: Should contain "lltc,ltc2941" or "lltc,ltc2943" which also
-    indicates the type of I2C chip attached.
+- compatible: Should contain "lltc,ltc2941", "lltc,ltc2942", "lltc,ltc2943"
+    or "lltc,ltc2944" which also indicates the type of I2C chip attached.
 - reg: The 7-bit I2C address.
 - lltc,resistor-sense: The sense resistor value in milli-ohms. Can be a 32-bit
     negative value when the battery has been connected to the wrong end of the
diff --git a/dts/Bindings/power/supply/max8903-charger.txt b/dts/Bindings/power/supply/max8903-charger.txt
index f0f4e12b07..bab947fef0 100644
--- a/dts/Bindings/power/supply/max8903-charger.txt
+++ b/dts/Bindings/power/supply/max8903-charger.txt
@@ -21,5 +21,4 @@ Example:
 		flt-gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
 		chg-gpios = <&gpio3 15 GPIO_ACTIVE_LOW>;
 		cen-gpios = <&gpio2 5 GPIO_ACTIVE_LOW>;
-		status = "okay";
 	};
diff --git a/dts/Bindings/power/supply/maxim,max14656.txt b/dts/Bindings/power/supply/maxim,max14656.txt
index e03e85ae65..d6e8dfd0a5 100644
--- a/dts/Bindings/power/supply/maxim,max14656.txt
+++ b/dts/Bindings/power/supply/maxim,max14656.txt
@@ -12,7 +12,6 @@ Example:
 	clock-frequency = <50000>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_i2c2>;
-	status = "okay";
 
 	max14656@35 {
 		compatible = "maxim,max14656";