dts: update to v4.19-rc1

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

10 files changed, 87 insertions, 14 deletions

diff --git a/dts/Bindings/power/power_domain.txt b/dts/Bindings/power/power_domain.txt
index 7dec508987..8f8b25a24b 100644
--- a/dts/Bindings/power/power_domain.txt
+++ b/dts/Bindings/power/power_domain.txt
@@ -114,18 +114,26 @@ Required properties:
  - power-domains : A list of PM domain specifiers, as defined by bindings of
 		the power controller that is the PM domain provider.
 
+Optional properties:
+ - power-domain-names : A list of power domain name strings sorted in the same
+		order as the power-domains property. Consumers drivers will use
+		power-domain-names to match power domains with power-domains
+		specifiers.
+
 Example:
 
 	leaky-device@12350000 {
 		compatible = "foo,i-leak-current";
 		reg = <0x12350000 0x1000>;
 		power-domains = <&power 0>;
+		power-domain-names = "io";
 	};
 
 	leaky-device@12351000 {
 		compatible = "foo,i-leak-current";
 		reg = <0x12351000 0x1000>;
 		power-domains = <&power 0>, <&power 1> ;
+		power-domain-names = "io", "clk";
 	};
 
 The first example above defines a typical PM domain consumer device, which is
diff --git a/dts/Bindings/power/reset/qcom,pon.txt b/dts/Bindings/power/reset/qcom,pon.txt
new file mode 100644
index 0000000000..651491bb63
--- /dev/null
+++ b/dts/Bindings/power/reset/qcom,pon.txt
@@ -0,0 +1,45 @@
+Qualcomm PON Device
+
+The Power On device for Qualcomm PM8xxx is MFD supporting pwrkey
+and resin along with the Android reboot-mode.
+
+This DT node has pwrkey and resin as sub nodes.
+
+Required Properties:
+-compatible: "qcom,pm8916-pon"
+-reg: Specifies the physical address of the pon register
+
+Optional subnode:
+-pwrkey: Specifies the subnode pwrkey and should follow the
+ qcom,pm8941-pwrkey.txt description.
+-resin: Specifies the subnode resin and should follow the
+ qcom,pm8xxx-pwrkey.txt description.
+
+The rest of the properties should follow the generic reboot-mode description
+found in reboot-mode.txt
+
+Example:
+
+	pon@800 {
+		compatible = "qcom,pm8916-pon";
+
+		reg = <0x800>;
+		mode-bootloader = <0x2>;
+		mode-recovery = <0x1>;
+
+		pwrkey {
+			compatible = "qcom,pm8941-pwrkey";
+			interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
+			debounce = <15625>;
+			bias-pull-up;
+			linux,code = <KEY_POWER>;
+		};
+
+		resin {
+			compatible = "qcom,pm8941-resin";
+			interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
+			debounce = <15625>;
+			bias-pull-up;
+			linux,code = <KEY_VOLUMEDOWN>;
+		};
+	};
diff --git a/dts/Bindings/power/supply/act8945a-charger.txt b/dts/Bindings/power/supply/act8945a-charger.txt
index b86ecada4f..c7dfb7cecf 100644
--- a/dts/Bindings/power/supply/act8945a-charger.txt
+++ b/dts/Bindings/power/supply/act8945a-charger.txt
@@ -9,8 +9,6 @@ Required properties:
  - interrupts: <a b> where a is the interrupt number and b is a
    field that represents an encoding of the sense and level
    information for the interrupt.
- - interrupt-parent: the phandle for the interrupt controller that
-   services interrupts for this device.
 
 Optional properties:
  - active-semi,input-voltage-threshold-microvolt: unit: mV;
diff --git a/dts/Bindings/power/supply/bq24257.txt b/dts/Bindings/power/supply/bq24257.txt
index d693702c9c..f8f5a1685b 100644
--- a/dts/Bindings/power/supply/bq24257.txt
+++ b/dts/Bindings/power/supply/bq24257.txt
@@ -6,8 +6,6 @@ Required properties:
  * "ti,bq24251"
  * "ti,bq24257"
 - reg: integer, i2c address of the device.
-- interrupt-parent: Should be the phandle for the interrupt controller. Use in
-    conjunction with "interrupts".
 - interrupts: Interrupt mapping for GPIO IRQ (configure for both edges). Use in
     conjunction with "interrupt-parent".
 - ti,battery-regulation-voltage: integer, maximum charging voltage in uV.
diff --git a/dts/Bindings/power/supply/lp8727_charger.txt b/dts/Bindings/power/supply/lp8727_charger.txt
index 2246bc5c87..0355a4b68f 100644
--- a/dts/Bindings/power/supply/lp8727_charger.txt
+++ b/dts/Bindings/power/supply/lp8727_charger.txt
@@ -5,7 +5,6 @@ Required properties:
 - reg: I2C slave address 27h
 
 Optional properties:
-- interrupt-parent: interrupt controller node (see interrupt binding[0])
 - interrupts: interrupt specifier (see interrupt binding[0])
 - debounce-ms: interrupt debounce time. (u32)
 
diff --git a/dts/Bindings/power/supply/maxim,ds2760.txt b/dts/Bindings/power/supply/maxim,ds2760.txt
new file mode 100644
index 0000000000..55967a0bee
--- /dev/null
+++ b/dts/Bindings/power/supply/maxim,ds2760.txt
@@ -0,0 +1,26 @@
+Devicetree bindings for Maxim DS2760
+====================================
+
+The ds2760 is a w1 slave device and must hence have its sub-node in DT
+under a w1 bus master node.
+
+The device exposes a power supply, so the details described in
+Documentation/devicetree/bindings/power/supply/power_supply.txt apply.
+
+Required properties:
+- compatible: must be "maxim,ds2760"
+
+Optional properties:
+- power-supplies:	Refers to one or more power supplies connected to
+			this battery.
+- maxim,pmod-enabled:	This boolean property enables the DS2760 to enter
+			sleep mode when the DQ line goes low for greater
+			than 2 seconds and leave sleep Mode when the DQ
+			line goes high.
+- maxim,cache-time-ms:	Time im milliseconds to cache the data for. When
+			this time expires, the values are read again from
+			the hardware. Defaults to 1000.
+- rated-capacity-microamp-hours:
+			The rated capacity of the battery, in mAh.
+			If not specified, the value stored in the
+			non-volatile chip memory is used.
diff --git a/dts/Bindings/power/supply/maxim,max14656.txt b/dts/Bindings/power/supply/maxim,max14656.txt
index d6e8dfd0a5..f956247d49 100644
--- a/dts/Bindings/power/supply/maxim,max14656.txt
+++ b/dts/Bindings/power/supply/maxim,max14656.txt
@@ -3,7 +3,6 @@ Maxim MAX14656 / AL32 USB Charger Detector
 Required properties :
 - compatible : "maxim,max14656";
 - reg: i2c slave address
-- interrupt-parent: the phandle for the interrupt controller
 - interrupts: interrupt line
 
 Example:
diff --git a/dts/Bindings/power/supply/rt9455_charger.txt b/dts/Bindings/power/supply/rt9455_charger.txt
index 5d9ad5cf2c..1e6107c757 100644
--- a/dts/Bindings/power/supply/rt9455_charger.txt
+++ b/dts/Bindings/power/supply/rt9455_charger.txt
@@ -4,8 +4,6 @@ Required properties:
 - compatible:				it should contain one of the following:
 					"richtek,rt9455".
 - reg:					integer, i2c address of the device.
-- interrupt-parent:			the phandle for the interrupt controller that
-					services interrupts for this device.
 - interrupts:				interrupt mapping for GPIO IRQ, it should be
 					configured with IRQ_TYPE_LEVEL_LOW flag.
 - richtek,output-charge-current:	integer, output current from the charger to the
diff --git a/dts/Bindings/power/supply/sbs_sbs-battery.txt b/dts/Bindings/power/supply/sbs_sbs-battery.txt
index c40e8926fa..4e78e51018 100644
--- a/dts/Bindings/power/supply/sbs_sbs-battery.txt
+++ b/dts/Bindings/power/supply/sbs_sbs-battery.txt
@@ -2,7 +2,11 @@ SBS sbs-battery
 ~~~~~~~~~~
 
 Required properties :
- - compatible : "sbs,sbs-battery"
+ - compatible: "<vendor>,<part-number>", "sbs,sbs-battery" as fallback. The
+     part number compatible string might be used in order to take care of
+     vendor specific registers.
+     Known <vendor>,<part-number>:
+       ti,bq20z75
 
 Optional properties :
  - sbs,i2c-retry-count : The number of times to retry i2c transactions on i2c
@@ -14,9 +18,9 @@ Optional properties :
 
 Example:
 
-	bq20z75@b {
-		compatible = "sbs,sbs-battery";
-		reg = < 0xb >;
+	battery@b {
+		compatible = "ti,bq20z75", "sbs,sbs-battery";
+		reg = <0xb>;
 		sbs,i2c-retry-count = <2>;
 		sbs,poll-retry-count = <10>;
 		sbs,battery-detect-gpios = <&gpio-controller 122 1>;
diff --git a/dts/Bindings/power/supply/sbs_sbs-charger.txt b/dts/Bindings/power/supply/sbs_sbs-charger.txt
index a3719623a9..84e74151ee 100644
--- a/dts/Bindings/power/supply/sbs_sbs-charger.txt
+++ b/dts/Bindings/power/supply/sbs_sbs-charger.txt
@@ -7,8 +7,6 @@ Required properties:
      specific registers.
 
 Optional properties:
-- interrupt-parent: Should be the phandle for the interrupt controller. Use in
-    conjunction with "interrupts".
 - interrupts: Interrupt mapping for GPIO IRQ. Use in conjunction with
     "interrupt-parent". If an interrupt is not provided the driver will switch
     automatically to polling.