dts: update to v3.18-rc1

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

5 files changed, 192 insertions, 0 deletions

diff --git a/dts/Bindings/power/power_domain.txt b/dts/Bindings/power/power_domain.txt
new file mode 100644
index 0000000000..98c16672ab
--- /dev/null
+++ b/dts/Bindings/power/power_domain.txt
@@ -0,0 +1,49 @@
+* Generic PM domains
+
+System on chip designs are often divided into multiple PM domains that can be
+used for power gating of selected IP blocks for power saving by reduced leakage
+current.
+
+This device tree binding can be used to bind PM domain consumer devices with
+their PM domains provided by PM domain providers. A PM domain provider can be
+represented by any node in the device tree and can provide one or more PM
+domains. A consumer node can refer to the provider by a phandle and a set of
+phandle arguments (so called PM domain specifiers) of length specified by the
+#power-domain-cells property in the PM domain provider node.
+
+==PM domain providers==
+
+Required properties:
+ - #power-domain-cells : Number of cells in a PM domain specifier;
+   Typically 0 for nodes representing a single PM domain and 1 for nodes
+   providing multiple PM domains (e.g. power controllers), but can be any value
+   as specified by device tree binding documentation of particular provider.
+
+Example:
+
+	power: power-controller@12340000 {
+		compatible = "foo,power-controller";
+		reg = <0x12340000 0x1000>;
+		#power-domain-cells = <1>;
+	};
+
+The node above defines a power controller that is a PM domain provider and
+expects one cell as its phandle argument.
+
+==PM domain consumers==
+
+Required properties:
+ - power-domains : A phandle and PM domain specifier as defined by bindings of
+                   the power controller specified by phandle.
+
+Example:
+
+	leaky-device@12350000 {
+		compatible = "foo,i-leak-current";
+		reg = <0x12350000 0x1000>;
+		power-domains = <&power 0>;
+	};
+
+The node above defines a typical PM domain consumer device, which is located
+inside a PM domain with index 0 of a power controller represented by a node
+with the label "power".
diff --git a/dts/Bindings/power/reset/ltc2952-poweroff.txt b/dts/Bindings/power/reset/ltc2952-poweroff.txt
new file mode 100644
index 0000000000..0c94c637f6
--- /dev/null
+++ b/dts/Bindings/power/reset/ltc2952-poweroff.txt
@@ -0,0 +1,26 @@
+Binding for the LTC2952 PowerPath controller
+
+This chip is used to externally trigger a system shut down. Once the trigger has
+been sent, the chips' watchdog has to be reset to gracefully shut down.
+If the Linux systems decides to shut down it powers off the platform via the
+kill signal.
+
+Required properties:
+
+- compatible:		Must contain: "lltc,ltc2952"
+- trigger-gpios:	phandle + gpio-specifier for the GPIO connected to the
+			chip's trigger line
+- watchdog-gpios:	phandle + gpio-specifier for the GPIO connected to the
+			chip's watchdog line
+- kill-gpios:		phandle + gpio-specifier for the GPIO connected to the
+			chip's kill line
+
+Example:
+
+ltc2952 {
+	compatible = "lltc,ltc2952";
+
+	trigger-gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
+	watchdog-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+	kill-gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
+};
diff --git a/dts/Bindings/power/reset/st-reset.txt b/dts/Bindings/power/reset/st-reset.txt
new file mode 100644
index 0000000000..809af54f02
--- /dev/null
+++ b/dts/Bindings/power/reset/st-reset.txt
@@ -0,0 +1,11 @@
+*Device-Tree bindings for ST SW reset functionality
+
+Required properties:
+- compatible: should be "st,<chip>-restart".
+- st,syscfg: should be a phandle of the syscfg node.
+
+Example node:
+	restart {
+		compatible = "st,stih416-restart";
+		st,syscfg = <&syscfg_sbc>;
+	};
diff --git a/dts/Bindings/power/reset/syscon-reboot.txt b/dts/Bindings/power/reset/syscon-reboot.txt
new file mode 100644
index 0000000000..11906316b4
--- /dev/null
+++ b/dts/Bindings/power/reset/syscon-reboot.txt
@@ -0,0 +1,23 @@
+Generic SYSCON mapped register reset driver
+
+This is a generic reset driver using syscon to map the reset register.
+The reset is generally performed with a write to the reset register
+defined by the register map pointed by syscon reference plus the offset
+with the mask defined in the reboot node.
+
+Required properties:
+- compatible: should contain "syscon-reboot"
+- regmap: this is phandle to the register map node
+- offset: offset in the register map for the reboot register (in bytes)
+- mask: the reset value written to the reboot register (32 bit access)
+
+Default will be little endian mode, 32 bit access only.
+
+Examples:
+
+	reboot {
+	   compatible = "syscon-reboot";
+	   regmap = <&regmapnode>;
+	   offset = <0x0>;
+	   mask = <0x1>;
+	};
diff --git a/dts/Bindings/power/rockchip-io-domain.txt b/dts/Bindings/power/rockchip-io-domain.txt
new file mode 100644
index 0000000000..6fbf6e7ecd
--- /dev/null
+++ b/dts/Bindings/power/rockchip-io-domain.txt
@@ -0,0 +1,83 @@
+Rockchip SRAM for IO Voltage Domains:
+-------------------------------------
+
+IO domain voltages on some Rockchip SoCs are variable but need to be
+kept in sync between the regulators and the SoC using a special
+register.
+
+A specific example using rk3288:
+- If the regulator hooked up to a pin like SDMMC0_VDD is 3.3V then
+  bit 7 of GRF_IO_VSEL needs to be 0.  If the regulator hooked up to
+  that same pin is 1.8V then bit 7 of GRF_IO_VSEL needs to be 1.
+
+Said another way, this driver simply handles keeping bits in the SoC's
+general register file (GRF) in sync with the actual value of a voltage
+hooked up to the pins.
+
+Note that this driver specifically doesn't include:
+- any logic for deciding what voltage we should set regulators to
+- any logic for deciding whether regulators (or internal SoC blocks)
+  should have power or not have power
+
+If there were some other software that had the smarts of making
+decisions about regulators, it would work in conjunction with this
+driver.  When that other software adjusted a regulator's voltage then
+this driver would handle telling the SoC about it.  A good example is
+vqmmc for SD.  In that case the dw_mmc driver simply is told about a
+regulator.  It changes the regulator between 3.3V and 1.8V at the
+right time.  This driver notices the change and makes sure that the
+SoC is on the same page.
+
+
+Required properties:
+- compatible: should be one of:
+  - "rockchip,rk3188-io-voltage-domain" for rk3188
+  - "rockchip,rk3288-io-voltage-domain" for rk3288
+- rockchip,grf: phandle to the syscon managing the "general register files"
+
+
+You specify supplies using the standard regulator bindings by including
+a phandle the the relevant regulator.  All specified supplies must be able
+to report their voltage.  The IO Voltage Domain for any non-specified
+supplies will be not be touched.
+
+Possible supplies for rk3188:
+- ap0-supply:    The supply connected to AP0_VCC.
+- ap1-supply:    The supply connected to AP1_VCC.
+- cif-supply:    The supply connected to CIF_VCC.
+- flash-supply:  The supply connected to FLASH_VCC.
+- lcdc0-supply:  The supply connected to LCD0_VCC.
+- lcdc1-supply:  The supply connected to LCD1_VCC.
+- vccio0-supply: The supply connected to VCCIO0.
+- vccio1-supply: The supply connected to VCCIO1.
+                 Sometimes also labeled VCCIO1 and VCCIO2.
+
+Possible supplies for rk3288:
+- audio-supply:  The supply connected to APIO4_VDD.
+- bb-supply:     The supply connected to APIO5_VDD.
+- dvp-supply:    The supply connected to DVPIO_VDD.
+- flash0-supply: The supply connected to FLASH0_VDD.  Typically for eMMC
+- flash1-supply: The supply connected to FLASH1_VDD.  Also known as SDIO1.
+- gpio30-supply: The supply connected to APIO1_VDD.
+- gpio1830       The supply connected to APIO2_VDD.
+- lcdc-supply:   The supply connected to LCDC_VDD.
+- sdcard-supply: The supply connected to SDMMC0_VDD.
+- wifi-supply:   The supply connected to APIO3_VDD.  Also known as SDIO0.
+
+
+Example:
+
+	io-domains {
+		compatible = "rockchip,rk3288-io-voltage-domain";
+		rockchip,grf = <&grf>;
+
+		audio-supply = <&vcc18_codec>;
+		bb-supply = <&vcc33_io>;
+		dvp-supply = <&vcc_18>;
+		flash0-supply = <&vcc18_flashio>;
+		gpio1830-supply = <&vcc33_io>;
+		gpio30-supply = <&vcc33_pmuio>;
+		lcdc-supply = <&vcc33_lcd>;
+		sdcard-supply = <&vccio_sd>;
+		wifi-supply = <&vcc18_wl>;
+	};