dts: update to v4.18-rc1

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

3 files changed, 0 insertions, 276 deletions

diff --git a/dts/Bindings/powerpc/4xx/emac.txt b/dts/Bindings/powerpc/4xx/emac.txt
deleted file mode 100644
index 44b842b6ca..0000000000
--- a/dts/Bindings/powerpc/4xx/emac.txt
+++ /dev/null
@@ -1,206 +0,0 @@
-    4xx/Axon EMAC ethernet nodes
-
-    The EMAC ethernet controller in IBM and AMCC 4xx chips, and also
-    the Axon bridge.  To operate this needs to interact with a this
-    special McMAL DMA controller, and sometimes an RGMII or ZMII
-    interface.  In addition to the nodes and properties described
-    below, the node for the OPB bus on which the EMAC sits must have a
-    correct clock-frequency property.
-
-      i) The EMAC node itself
-
-    Required properties:
-    - device_type       : "network"
-
-    - compatible        : compatible list, contains 2 entries, first is
-			  "ibm,emac-CHIP" where CHIP is the host ASIC (440gx,
-			  405gp, Axon) and second is either "ibm,emac" or
-			  "ibm,emac4".  For Axon, thus, we have: "ibm,emac-axon",
-			  "ibm,emac4"
-    - interrupts        : <interrupt mapping for EMAC IRQ and WOL IRQ>
-    - interrupt-parent  : optional, if needed for interrupt mapping
-    - reg               : <registers mapping>
-    - local-mac-address : 6 bytes, MAC address
-    - mal-device        : phandle of the associated McMAL node
-    - mal-tx-channel    : 1 cell, index of the tx channel on McMAL associated
-			  with this EMAC
-    - mal-rx-channel    : 1 cell, index of the rx channel on McMAL associated
-			  with this EMAC
-    - cell-index        : 1 cell, hardware index of the EMAC cell on a given
-			  ASIC (typically 0x0 and 0x1 for EMAC0 and EMAC1 on
-			  each Axon chip)
-    - max-frame-size    : 1 cell, maximum frame size supported in bytes
-    - rx-fifo-size      : 1 cell, Rx fifo size in bytes for 10 and 100 Mb/sec
-			  operations.
-			  For Axon, 2048
-    - tx-fifo-size      : 1 cell, Tx fifo size in bytes for 10 and 100 Mb/sec
-			  operations.
-			  For Axon, 2048.
-    - fifo-entry-size   : 1 cell, size of a fifo entry (used to calculate
-			  thresholds).
-			  For Axon, 0x00000010
-    - mal-burst-size    : 1 cell, MAL burst size (used to calculate thresholds)
-			  in bytes.
-			  For Axon, 0x00000100 (I think ...)
-    - phy-mode          : string, mode of operations of the PHY interface.
-			  Supported values are: "mii", "rmii", "smii", "rgmii",
-			  "tbi", "gmii", rtbi", "sgmii".
-			  For Axon on CAB, it is "rgmii"
-    - mdio-device       : 1 cell, required iff using shared MDIO registers
-			  (440EP).  phandle of the EMAC to use to drive the
-			  MDIO lines for the PHY used by this EMAC.
-    - zmii-device       : 1 cell, required iff connected to a ZMII.  phandle of
-			  the ZMII device node
-    - zmii-channel      : 1 cell, required iff connected to a ZMII.  Which ZMII
-			  channel or 0xffffffff if ZMII is only used for MDIO.
-    - rgmii-device      : 1 cell, required iff connected to an RGMII. phandle
-			  of the RGMII device node.
-			  For Axon: phandle of plb5/plb4/opb/rgmii
-    - rgmii-channel     : 1 cell, required iff connected to an RGMII.  Which
-			  RGMII channel is used by this EMAC.
-			  Fox Axon: present, whatever value is appropriate for each
-			  EMAC, that is the content of the current (bogus) "phy-port"
-			  property.
-
-    Optional properties:
-    - phy-address       : 1 cell, optional, MDIO address of the PHY. If absent,
-			  a search is performed.
-    - phy-map           : 1 cell, optional, bitmap of addresses to probe the PHY
-			  for, used if phy-address is absent. bit 0x00000001 is
-			  MDIO address 0.
-			  For Axon it can be absent, though my current driver
-			  doesn't handle phy-address yet so for now, keep
-			  0x00ffffff in it.
-    - phy-handle	: Used to describe configurations where a external PHY
-			  is used. Please refer to:
-			  Documentation/devicetree/bindings/net/ethernet.txt
-    - rx-fifo-size-gige : 1 cell, Rx fifo size in bytes for 1000 Mb/sec
-			  operations (if absent the value is the same as
-			  rx-fifo-size).  For Axon, either absent or 2048.
-    - tx-fifo-size-gige : 1 cell, Tx fifo size in bytes for 1000 Mb/sec
-			  operations (if absent the value is the same as
-			  tx-fifo-size). For Axon, either absent or 2048.
-    - tah-device        : 1 cell, optional. If connected to a TAH engine for
-			  offload, phandle of the TAH device node.
-    - tah-channel       : 1 cell, optional. If appropriate, channel used on the
-			  TAH engine.
-    - fixed-link	: Fixed-link subnode describing a link to a non-MDIO
-			  managed entity. See
-			  Documentation/devicetree/bindings/net/fixed-link.txt
-			  for details.
-    - mdio subnode	: When the EMAC has a phy connected to its local
-			  mdio, which us supported by the kernel's network
-			  PHY library in drivers/net/phy, there must be device
-			  tree subnode with the following required properties:
-				- #address-cells: Must be <1>.
-				- #size-cells: Must be <0>.
-
-			  For PHY definitions: Please refer to
-			  Documentation/devicetree/bindings/net/phy.txt and
-			  Documentation/devicetree/bindings/net/ethernet.txt
-
-    Examples:
-
-	EMAC0: ethernet@40000800 {
-		device_type = "network";
-		compatible = "ibm,emac-440gp", "ibm,emac";
-		interrupt-parent = <&UIC1>;
-		interrupts = <1c 4 1d 4>;
-		reg = <40000800 70>;
-		local-mac-address = [00 04 AC E3 1B 1E];
-		mal-device = <&MAL0>;
-		mal-tx-channel = <0 1>;
-		mal-rx-channel = <0>;
-		cell-index = <0>;
-		max-frame-size = <5dc>;
-		rx-fifo-size = <1000>;
-		tx-fifo-size = <800>;
-		phy-mode = "rmii";
-		phy-map = <00000001>;
-		zmii-device = <&ZMII0>;
-		zmii-channel = <0>;
-	};
-
-	EMAC1: ethernet@ef600c00 {
-		device_type = "network";
-		compatible = "ibm,emac-apm821xx", "ibm,emac4sync";
-		interrupt-parent = <&EMAC1>;
-		interrupts = <0 1>;
-		#interrupt-cells = <1>;
-		#address-cells = <0>;
-		#size-cells = <0>;
-		interrupt-map = <0 &UIC2 0x10 IRQ_TYPE_LEVEL_HIGH /* Status */
-				 1 &UIC2 0x14 IRQ_TYPE_LEVEL_HIGH /* Wake */>;
-		reg = <0xef600c00 0x000000c4>;
-		local-mac-address = [000000000000]; /* Filled in by U-Boot */
-		mal-device = <&MAL0>;
-		mal-tx-channel = <0>;
-		mal-rx-channel = <0>;
-		cell-index = <0>;
-		max-frame-size = <9000>;
-		rx-fifo-size = <16384>;
-		tx-fifo-size = <2048>;
-		fifo-entry-size = <10>;
-		phy-mode = "rgmii";
-		phy-handle = <&phy0>;
-		phy-map = <0x00000000>;
-		rgmii-device = <&RGMII0>;
-		rgmii-channel = <0>;
-		tah-device = <&TAH0>;
-		tah-channel = <0>;
-		has-inverted-stacr-oc;
-		has-new-stacr-staopc;
-
-	        mdio {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			phy0: ethernet-phy@0 {
-				compatible = "ethernet-phy-ieee802.3-c22";
-				reg = <0>;
-			};
-		};
-	};
-
-
-      ii) McMAL node
-
-    Required properties:
-    - device_type        : "dma-controller"
-    - compatible         : compatible list, containing 2 entries, first is
-			   "ibm,mcmal-CHIP" where CHIP is the host ASIC (like
-			   emac) and the second is either "ibm,mcmal" or
-			   "ibm,mcmal2".
-			   For Axon, "ibm,mcmal-axon","ibm,mcmal2"
-    - interrupts         : <interrupt mapping for the MAL interrupts sources:
-                           5 sources: tx_eob, rx_eob, serr, txde, rxde>.
-                           For Axon: This is _different_ from the current
-			   firmware.  We use the "delayed" interrupts for txeob
-			   and rxeob. Thus we end up with mapping those 5 MPIC
-			   interrupts, all level positive sensitive: 10, 11, 32,
-			   33, 34 (in decimal)
-    - dcr-reg            : < DCR registers range >
-    - dcr-parent         : if needed for dcr-reg
-    - num-tx-chans       : 1 cell, number of Tx channels
-    - num-rx-chans       : 1 cell, number of Rx channels
-
-      iii) ZMII node
-
-    Required properties:
-    - compatible         : compatible list, containing 2 entries, first is
-			   "ibm,zmii-CHIP" where CHIP is the host ASIC (like
-			   EMAC) and the second is "ibm,zmii".
-			   For Axon, there is no ZMII node.
-    - reg                : <registers mapping>
-
-      iv) RGMII node
-
-    Required properties:
-    - compatible         : compatible list, containing 2 entries, first is
-			   "ibm,rgmii-CHIP" where CHIP is the host ASIC (like
-			   EMAC) and the second is "ibm,rgmii".
-                           For Axon, "ibm,rgmii-axon","ibm,rgmii"
-    - reg                : <registers mapping>
-    - revision           : as provided by the RGMII new version register if
-			   available.
-			   For Axon: 0x0000012a
diff --git a/dts/Bindings/powerpc/4xx/ndfc.txt b/dts/Bindings/powerpc/4xx/ndfc.txt
deleted file mode 100644
index 869f0b5f16..0000000000
--- a/dts/Bindings/powerpc/4xx/ndfc.txt
+++ /dev/null
@@ -1,39 +0,0 @@
-AMCC NDFC (NanD Flash Controller)
-
-Required properties:
-- compatible : "ibm,ndfc".
-- reg : should specify chip select and size used for the chip (0x2000).
-
-Optional properties:
-- ccr : NDFC config and control register value (default 0).
-- bank-settings : NDFC bank configuration register value (default 0).
-
-Notes:
-- partition(s) - follows the OF MTD standard for partitions
-
-Example:
-
-ndfc@1,0 {
-	compatible = "ibm,ndfc";
-	reg = <0x00000001 0x00000000 0x00002000>;
-	ccr = <0x00001000>;
-	bank-settings = <0x80002222>;
-	#address-cells = <1>;
-	#size-cells = <1>;
-
-	nand {
-		#address-cells = <1>;
-		#size-cells = <1>;
-
-		partition@0 {
-			label = "kernel";
-			reg = <0x00000000 0x00200000>;
-		};
-		partition@200000 {
-			label = "root";
-			reg = <0x00200000 0x03E00000>;
-		};
-	};
-};
-
-
diff --git a/dts/Bindings/powerpc/fsl/gtm.txt b/dts/Bindings/powerpc/fsl/gtm.txt
deleted file mode 100644
index 9a33efded4..0000000000
--- a/dts/Bindings/powerpc/fsl/gtm.txt
+++ /dev/null
@@ -1,31 +0,0 @@
-* Freescale General-purpose Timers Module
-
-Required properties:
-  - compatible : should be
-    "fsl,<chip>-gtm", "fsl,gtm" for SOC GTMs
-    "fsl,<chip>-qe-gtm", "fsl,qe-gtm", "fsl,gtm" for QE GTMs
-    "fsl,<chip>-cpm2-gtm", "fsl,cpm2-gtm", "fsl,gtm" for CPM2 GTMs
-  - reg : should contain gtm registers location and length (0x40).
-  - interrupts : should contain four interrupts.
-  - interrupt-parent : interrupt source phandle.
-  - clock-frequency : specifies the frequency driving the timer.
-
-Example:
-
-timer@500 {
-	compatible = "fsl,mpc8360-gtm", "fsl,gtm";
-	reg = <0x500 0x40>;
-	interrupts = <90 8 78 8 84 8 72 8>;
-	interrupt-parent = <&ipic>;
-	/* filled by u-boot */
-	clock-frequency = <0>;
-};
-
-timer@440 {
-	compatible = "fsl,mpc8360-qe-gtm", "fsl,qe-gtm", "fsl,gtm";
-	reg = <0x440 0x40>;
-	interrupts = <12 13 14 15>;
-	interrupt-parent = <&qeic>;
-	/* filled by u-boot */
-	clock-frequency = <0>;
-};