dts: update to v5.2-rc1

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

2 files changed, 65 insertions, 8 deletions

diff --git a/dts/Bindings/regulator/gpio-regulator.txt b/dts/Bindings/regulator/gpio-regulator.txt
index 1f496159e2..dd25e73b5d 100644
--- a/dts/Bindings/regulator/gpio-regulator.txt
+++ b/dts/Bindings/regulator/gpio-regulator.txt
@@ -4,16 +4,30 @@ Required properties:
 - compatible		: Must be "regulator-gpio".
 - regulator-name	: Defined in regulator.txt as optional, but required
 			  here.
-- states		: Selection of available voltages and GPIO configs.
-                          if there are no states, then use a fixed regulator
+- gpios			: Array of one or more GPIO pins used to select the
+			  regulator voltage/current listed in "states".
+- states		: Selection of available voltages/currents provided by
+			  this regulator and matching GPIO configurations to
+			  achieve them. If there are no states in the "states"
+			  array, use a fixed regulator instead.
 
 Optional properties:
-- enable-gpio		: GPIO to use to enable/disable the regulator.
-- gpios			: GPIO group used to control voltage.
-- gpios-states		: gpios pin's initial states array. 0: LOW, 1: HIGH.
-			  defualt is LOW if nothing is specified.
+- enable-gpios		: GPIO used to enable/disable the regulator.
+			  Warning, the GPIO phandle flags are ignored and the
+			  GPIO polarity is controlled solely by the presence
+			  of "enable-active-high" DT property. This is due to
+			  compatibility with old DTs.
+- enable-active-high	: Polarity of "enable-gpio" GPIO is active HIGH.
+			  Default is active LOW.
+- gpios-states		: On operating systems, that don't support reading back
+			  gpio values in output mode (most notably linux), this
+			  array provides the state of GPIO pins set when
+			  requesting them from the gpio controller. Systems,
+			  that are capable of preserving state when requesting
+			  the lines, are free to ignore this property.
+			  0: LOW, 1: HIGH. Default is LOW if nothing else
+			  is specified.
 - startup-delay-us	: Startup time in microseconds.
-- enable-active-high	: Polarity of GPIO is active high (default is low).
 - regulator-type	: Specifies what is being regulated, must be either
 			  "voltage" or "current", defaults to voltage.
 
@@ -30,7 +44,7 @@ Example:
 		regulator-max-microvolt = <2600000>;
 		regulator-boot-on;
 
-		enable-gpio = <&gpio0 23 0x4>;
+		enable-gpios = <&gpio0 23 0x4>;
 		gpios = <&gpio0 24 0x4
 			 &gpio0 25 0x4>;
 		states = <1800000 0x3
diff --git a/dts/Bindings/regulator/st,stm32mp1-pwr-reg.txt b/dts/Bindings/regulator/st,stm32mp1-pwr-reg.txt
new file mode 100644
index 0000000000..e372dd3f0c
--- /dev/null
+++ b/dts/Bindings/regulator/st,stm32mp1-pwr-reg.txt
@@ -0,0 +1,43 @@
+STM32MP1 PWR Regulators
+-----------------------
+
+Available Regulators in STM32MP1 PWR block are:
+  - reg11 for regulator 1V1
+  - reg18 for regulator 1V8
+  - usb33 for the swtich USB3V3
+
+Required properties:
+- compatible: Must be "st,stm32mp1,pwr-reg"
+- list of child nodes that specify the regulator reg11, reg18 or usb33
+  initialization data for defined regulators. The definition for each of
+  these nodes is defined using the standard binding for regulators found at
+  Documentation/devicetree/bindings/regulator/regulator.txt.
+- vdd-supply: phandle to the parent supply/regulator node for vdd input
+- vdd_3v3_usbfs-supply: phandle to the parent supply/regulator node for usb33
+
+Example:
+
+pwr_regulators: pwr@50001000 {
+	compatible = "st,stm32mp1,pwr-reg";
+	reg = <0x50001000 0x10>;
+	vdd-supply = <&vdd>;
+	vdd_3v3_usbfs-supply = <&vdd_usb>;
+
+	reg11: reg11 {
+		regulator-name = "reg11";
+		regulator-min-microvolt = <1100000>;
+		regulator-max-microvolt = <1100000>;
+	};
+
+	reg18: reg18 {
+		regulator-name = "reg18";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	usb33: usb33 {
+		regulator-name = "usb33";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+};