dts: update to v6.0-rc1

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

7 files changed, 455 insertions, 439 deletions

diff --git a/dts/Bindings/regulator/mps,mp5416.yaml b/dts/Bindings/regulator/mps,mp5416.yaml
index 90727fdc12..7023c597c3 100644
--- a/dts/Bindings/regulator/mps,mp5416.yaml
+++ b/dts/Bindings/regulator/mps,mp5416.yaml
@@ -15,6 +15,7 @@ properties:
   compatible:
     enum:
       - mps,mp5416
+      - mps,mp5496
 
   reg:
     maxItems: 1
diff --git a/dts/Bindings/regulator/pwm-regulator.txt b/dts/Bindings/regulator/pwm-regulator.txt
deleted file mode 100644
index 3d78d507e2..0000000000
--- a/dts/Bindings/regulator/pwm-regulator.txt
+++ /dev/null
@@ -1,92 +0,0 @@
-Bindings for the Generic PWM Regulator
-======================================
-
-Currently supports 2 modes of operation:
-
-Voltage Table:		When in this mode, a voltage table (See below) of
-			predefined voltage <=> duty-cycle values must be
-			provided via DT. Limitations are that the regulator can
-			only operate at the voltages supplied in the table.
-			Intermediary duty-cycle values which would normally
-			allow finer grained voltage selection are ignored and
-			rendered useless.  Although more control is given to
-			the user if the assumptions made in continuous-voltage
-			mode do not reign true.
-
-Continuous Voltage:	This mode uses the regulator's maximum and minimum
-			supplied voltages specified in the
-			regulator-{min,max}-microvolt properties to calculate
-			appropriate duty-cycle values.  This allows for a much
-			more fine grained solution when compared with
-			voltage-table mode above.  This solution does make an
-			assumption that a %50 duty-cycle value will cause the
-			regulator voltage to run at half way between the
-			supplied max_uV and min_uV values.
-
-Required properties:
---------------------
-- compatible:		Should be "pwm-regulator"
-
-- pwms:			PWM specification (See: ../pwm/pwm.txt)
-
-Only required for Voltage Table Mode:
-- voltage-table: 	Voltage and Duty-Cycle table consisting of 2 cells
-			    First cell is voltage in microvolts (uV)
-			    Second cell is duty-cycle in percent (%)
-
-Optional properties for Continuous mode:
-- pwm-dutycycle-unit:	Integer value encoding the duty cycle unit. If not
-			defined, <100> is assumed, meaning that
-			pwm-dutycycle-range contains values expressed in
-			percent.
-
-- pwm-dutycycle-range:	Should contain 2 entries. The first entry is encoding
-			the dutycycle for regulator-min-microvolt and the
-			second one the dutycycle for regulator-max-microvolt.
-			Duty cycle values are expressed in pwm-dutycycle-unit.
-			If not defined, <0 100> is assumed.
-
-NB: To be clear, if voltage-table is provided, then the device will be used
-in Voltage Table Mode.  If no voltage-table is provided, then the device will
-be used in Continuous Voltage Mode.
-
-Optional properties:
---------------------
-- enable-gpios:		GPIO to use to enable/disable the regulator
-
-Any property defined as part of the core regulator binding can also be used.
-(See: ../regulator/regulator.txt)
-
-Continuous Voltage With Enable GPIO Example:
-	pwm_regulator {
-		compatible = "pwm-regulator";
-		pwms = <&pwm1 0 8448 0>;
-		enable-gpios = <&gpio0 23 GPIO_ACTIVE_HIGH>;
-		regulator-min-microvolt = <1016000>;
-		regulator-max-microvolt = <1114000>;
-		regulator-name = "vdd_logic";
-		/* unit == per-mille */
-		pwm-dutycycle-unit = <1000>;
-		/*
-		 * Inverted PWM logic, and the duty cycle range is limited
-		 * to 30%-70%.
-		 */
-		pwm-dutycycle-range = <700 300>; /* */
-	};
-
-Voltage Table Example:
-	pwm_regulator {
-		compatible = "pwm-regulator";
-		pwms = <&pwm1 0 8448 0>;
-		regulator-min-microvolt = <1016000>;
-		regulator-max-microvolt = <1114000>;
-		regulator-name = "vdd_logic";
-
-			      /* Voltage Duty-Cycle */
-		voltage-table = <1114000 0>,
-				<1095000 10>,
-				<1076000 20>,
-				<1056000 30>,
-				<1036000 40>,
-				<1016000 50>;
-	};
diff --git a/dts/Bindings/regulator/pwm-regulator.yaml b/dts/Bindings/regulator/pwm-regulator.yaml
new file mode 100644
index 0000000000..82b6f2fde4
--- /dev/null
+++ b/dts/Bindings/regulator/pwm-regulator.yaml
@@ -0,0 +1,126 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/regulator/pwm-regulator.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Bindings for the Generic PWM Regulator
+
+maintainers:
+  - Brian Norris <briannorris@chromium.org>
+  - Lee Jones <lee@kernel.org>
+  - Alexandre Courbot <acourbot@nvidia.com>
+
+description: |
+  Currently supports 2 modes of operation:
+
+  Voltage Table:
+    When in this mode, a voltage table (See below) of predefined voltage <=>
+    duty-cycle values must be provided via DT. Limitations are that the
+    regulator can only operate at the voltages supplied in the table.
+    Intermediary duty-cycle values which would normally allow finer grained
+    voltage selection are ignored and rendered useless.  Although more control
+    is given to the user if the assumptions made in continuous-voltage mode do
+    not reign true.
+
+  Continuous Voltage:
+    This mode uses the regulator's maximum and minimum supplied voltages
+    specified in the regulator-{min,max}-microvolt properties to calculate
+    appropriate duty-cycle values.  This allows for a much more fine grained
+    solution when compared with voltage-table mode above.  This solution does
+    make an assumption that a %50 duty-cycle value will cause the regulator
+    voltage to run at half way between the supplied max_uV and min_uV values.
+
+  If voltage-table is provided, then the device will be used in Voltage Table
+  Mode.  If no voltage-table is provided, then the device will be used in
+  Continuous Voltage Mode.
+
+allOf:
+  - $ref: regulator.yaml#
+
+properties:
+  compatible:
+    const: pwm-regulator
+
+  pwms:
+    maxItems: 1
+
+  voltage-table:
+    description: Voltage and Duty-Cycle table.
+    $ref: /schemas/types.yaml#/definitions/uint32-matrix
+    items:
+      items:
+        - description: voltage in microvolts (uV)
+        - description: duty-cycle in percent (%)
+
+  enable-gpios:
+    description: Regulator enable GPIO
+    maxItems: 1
+
+   # Optional properties for Continuous mode:
+  pwm-dutycycle-unit:
+    description:
+      Integer value encoding the duty cycle unit. If not
+        defined, <100> is assumed, meaning that
+        pwm-dutycycle-range contains values expressed in
+        percent.
+    default: 100
+
+  pwm-dutycycle-range:
+    description:
+      Should contain 2 entries. The first entry is encoding
+        the dutycycle for regulator-min-microvolt and the
+        second one the dutycycle for regulator-max-microvolt.
+        Duty cycle values are expressed in pwm-dutycycle-unit.
+        If not defined, <0 100> is assumed.
+    $ref: /schemas/types.yaml#/definitions/uint32-array
+    items:
+      - description: the dutycycle for regulator-min-microvolt
+      - description: the dutycycle for regulator-max-microvolt
+    default: [ 0 100 ]
+
+required:
+  - compatible
+  - pwms
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    // Continuous Voltage With Enable GPIO Example:
+    regulator {
+        compatible = "pwm-regulator";
+        pwms = <&pwm1 0 8448 0>;
+        enable-gpios = <&gpio0 23 GPIO_ACTIVE_HIGH>;
+        regulator-min-microvolt = <1016000>;
+        regulator-max-microvolt = <1114000>;
+        regulator-name = "vdd_logic";
+        /* unit == per-mille */
+        pwm-dutycycle-unit = <1000>;
+        /*
+        * Inverted PWM logic, and the duty cycle range is limited
+        * to 30%-70%.
+        */
+        pwm-dutycycle-range = <700 300>; /* */
+    };
+
+  - |
+    // Voltage Table Example:
+    regulator {
+        compatible = "pwm-regulator";
+        pwms = <&pwm1 0 8448 0>;
+        regulator-min-microvolt = <1016000>;
+        regulator-max-microvolt = <1114000>;
+        regulator-name = "vdd_logic";
+
+                /* Voltage Duty-Cycle */
+        voltage-table = <1114000 0>,
+            <1095000 10>,
+            <1076000 20>,
+            <1056000 30>,
+            <1036000 40>,
+            <1016000 50>;
+    };
+...
diff --git a/dts/Bindings/regulator/qcom,smd-rpm-regulator.yaml b/dts/Bindings/regulator/qcom,smd-rpm-regulator.yaml
index 6a9a7eed46..c233461cc9 100644
--- a/dts/Bindings/regulator/qcom,smd-rpm-regulator.yaml
+++ b/dts/Bindings/regulator/qcom,smd-rpm-regulator.yaml
@@ -30,6 +30,9 @@ description:
 
   For pm8841, s1, s2, s3, s4, s5, s6, s7, s8
 
+  For pm8909, s1, s2, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13,
+  l14, l15, l17, l18
+
   For pm8916, s1, s2, s3, s4, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11,
   l12, l13, l14, l15, l16, l17, l18
 
@@ -78,6 +81,7 @@ properties:
       - qcom,rpm-mp5496-regulators
       - qcom,rpm-pm8226-regulators
       - qcom,rpm-pm8841-regulators
+      - qcom,rpm-pm8909-regulators
       - qcom,rpm-pm8916-regulators
       - qcom,rpm-pm8941-regulators
       - qcom,rpm-pm8950-regulators
diff --git a/dts/Bindings/regulator/qcom,spmi-regulator.txt b/dts/Bindings/regulator/qcom,spmi-regulator.txt
deleted file mode 100644
index c2a39b121b..0000000000
--- a/dts/Bindings/regulator/qcom,spmi-regulator.txt
+++ /dev/null
@@ -1,347 +0,0 @@
-Qualcomm SPMI Regulators
-
-- compatible:
-	Usage: required
-	Value type: <string>
-	Definition: must be one of:
-			"qcom,pm8004-regulators"
-			"qcom,pm8005-regulators"
-			"qcom,pm8226-regulators"
-			"qcom,pm8841-regulators"
-			"qcom,pm8916-regulators"
-			"qcom,pm8941-regulators"
-			"qcom,pm8950-regulators"
-			"qcom,pm8994-regulators"
-			"qcom,pmi8994-regulators"
-			"qcom,pm660-regulators"
-			"qcom,pm660l-regulators"
-			"qcom,pms405-regulators"
-
-- interrupts:
-	Usage: optional
-	Value type: <prop-encoded-array>
-	Definition: List of OCP interrupts.
-
-- interrupt-names:
-	Usage: required if 'interrupts' property present
-	Value type: <string-array>
-	Definition: List of strings defining the names of the
-		    interrupts in the 'interrupts' property 1-to-1.
-		    Supported values are "ocp-<regulator_name>", where
-		    <regulator_name> corresponds to a voltage switch
-		    type regulator.
-
-- vdd_s1-supply:
-- vdd_s2-supply:
-- vdd_s3-supply:
-- vdd_s4-supply:
-- vdd_s5-supply:
-- vdd_s6-supply:
-- vdd_s7-supply:
-- vdd_s8-supply:
-	Usage: optional (pm8841 only)
-	Value type: <phandle>
-	Definition: Reference to regulator supplying the input pin, as
-		    described in the data sheet.
-
-- vdd_s1-supply:
-- vdd_s2-supply:
-- vdd_s3-supply:
-- vdd_s4-supply:
-- vdd_l1_l3-supply:
-- vdd_l2-supply:
-- vdd_l4_l5_l6-supply:
-- vdd_l7-supply:
-- vdd_l8_l11_l14_l15_l16-supply:
-- vdd_l9_l10_l12_l13_l17_l18-supply:
-	Usage: optional (pm8916 only)
-	Value type: <phandle>
-	Definition: Reference to regulator supplying the input pin, as
-		    described in the data sheet.
-
-- vdd_s1-supply:
-- vdd_s2-supply:
-- vdd_s3-supply:
-- vdd_l1_l3-supply:
-- vdd_l2_lvs_1_2_3-supply:
-- vdd_l4_l11-supply:
-- vdd_l5_l7-supply:
-- vdd_l6_l12_l14_l15-supply:
-- vdd_l8_l16_l18_19-supply:
-- vdd_l9_l10_l17_l22-supply:
-- vdd_l13_l20_l23_l24-supply:
-- vdd_l21-supply:
-- vin_5vs-supply:
-	Usage: optional (pm8941 only)
-	Value type: <phandle>
-	Definition: Reference to regulator supplying the input pin, as
-		    described in the data sheet.
-
-- vdd_s1-supply:
-- vdd_s2-supply:
-- vdd_s3-supply:
-- vdd_s4-supply:
-- vdd_s4-supply:
-- vdd_s5-supply:
-- vdd_s6-supply:
-- vdd_l1_l19-supply:
-- vdd_l2_l23-supply:
-- vdd_l3-supply:
-- vdd_l4_l5_l6_l7_l16-supply:
-- vdd_l8_l11_l12_l17_l22-supply:
-- vdd_l9_l10_l13_l14_l15_l18-supply:
-- vdd_l20-supply:
-- vdd_l21-supply:
-	Usage: optional (pm8950 only)
-	Value type: <phandle>
-	Definition: reference to regulator supplying the input pin, as
-		    described in the data sheet
-
-- vdd_s1-supply:
-- vdd_s2-supply:
-- vdd_s3-supply:
-- vdd_s4-supply:
-- vdd_s5-supply:
-- vdd_s6-supply:
-- vdd_s7-supply:
-- vdd_s8-supply:
-- vdd_s9-supply:
-- vdd_s10-supply:
-- vdd_s11-supply:
-- vdd_s12-supply:
-- vdd_l1-supply:
-- vdd_l2_l26_l28-supply:
-- vdd_l3_l11-supply:
-- vdd_l4_l27_l31-supply:
-- vdd_l5_l7-supply:
-- vdd_l6_l12_l32-supply:
-- vdd_l8_l16_l30-supply:
-- vdd_l9_l10_l18_l22-supply:
-- vdd_l13_l19_l23_l24-supply:
-- vdd_l14_l15-supply:
-- vdd_l17_l29-supply:
-- vdd_l20_l21-supply:
-- vdd_l25-supply:
-- vdd_lvs_1_2-supply:
-	Usage: optional (pm8994 only)
-	Value type: <phandle>
-	Definition: Reference to regulator supplying the input pin, as
-		    described in the data sheet.
-
-- vdd_s1-supply:
-- vdd_s2-supply:
-- vdd_s3-supply:
-- vdd_l1-supply:
-	Usage: optional (pmi8994 only)
-	Value type: <phandle>
-	Definition: Reference to regulator supplying the input pin, as
-		    described in the data sheet.
-
-- vdd_l1_l6_l7-supply:
-- vdd_l2_l3-supply:
-- vdd_l5-supply:
-- vdd_l8_l9_l10_l11_l12_l13_l14-supply:
-- vdd_l15_l16_l17_l18_l19-supply:
-- vdd_s1-supply:
-- vdd_s2-supply:
-- vdd_s3-supply:
-- vdd_s5-supply:
-- vdd_s6-supply:
-	Usage: optional (pm660 only)
-	Value type: <phandle>
-	Definition: Reference to regulator supplying the input pin, as
-		    described in the data sheet.
-
-- vdd_l1_l9_l10-supply:
-- vdd_l2-supply:
-- vdd_l3_l5_l7_l8-supply:
-- vdd_l4_l6-supply:
-- vdd_s1-supply:
-- vdd_s2-supply:
-- vdd_s3-supply:
-- vdd_s4-supply:
-- vdd_s5-supply:
-	Usage: optional (pm660l only)
-	Value type: <phandle>
-	Definition: Reference to regulator supplying the input pin, as
-		    described in the data sheet.
-
-- vdd_l1_l2-supply:
-- vdd_l3_l8-supply:
-- vdd_l4-supply:
-- vdd_l5_l6-supply:
-- vdd_l10_l11_l12_l13-supply:
-- vdd_l7-supply:
-- vdd_l9-supply:
-- vdd_s1-supply:
-- vdd_s2-supply:
-- vdd_s3-supply:
-- vdd_s4-supply:
-- vdd_s5-supply
-	Usage: optional (pms405 only)
-	Value type: <phandle>
-	Definition: Reference to regulator supplying the input pin, as
-		    described in the data sheet.
-
-- qcom,saw-reg:
-	Usage: optional
-	Value type: <phandle>
-	Description: Reference to syscon node defining the SAW registers.
-
-
-The regulator node houses sub-nodes for each regulator within the device. Each
-sub-node is identified using the node's name, with valid values listed for each
-of the PMICs below.
-
-pm8004:
-	s2, s5
-
-pm8005:
-	s1, s2, s3, s4
-
-pm8841:
-	s1, s2, s3, s4, s5, s6, s7, s8
-
-pm8916:
-	s1, s2, s3, s4, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13,
-	l14, l15, l16, l17, l18
-
-pm8941:
-	s1, s2, s3, s4, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13,
-	l14, l15, l16, l17, l18, l19, l20, l21, l22, l23, l24, lvs1, lvs2, lvs3,
-	5vs1, 5vs2
-
-pm8994:
-	s1, s2, s3, s4, s5, s6, s7, s8, s9, s10, s11, s12, l1, l2, l3, l4, l5,
-	l6, l7, l8, l9, l10, l11, l12, l13, l14, l15, l16, l17, l18, l19, l20,
-	l21, l22, l23, l24, l25, l26, l27, l28, l29, l30, l31, l32, lvs1, lvs2
-
-pmi8994:
-	s1, s2, s3, l1
-
-The content of each sub-node is defined by the standard binding for regulators -
-see regulator.txt - with additional custom properties described below:
-
-- regulator-initial-mode:
-	Usage: optional
-	Value type: <u32>
-	Description: 2 = Set initial mode to auto mode (automatically select
-		    between HPM and LPM); not available on boost type
-		    regulators.
-
-		    1 = Set initial mode to high power mode (HPM), also referred
-		    to as NPM. HPM consumes more ground current than LPM, but
-		    it can source significantly higher load current. HPM is not
-		    available on boost type regulators. For voltage switch type
-		    regulators, HPM implies that over current protection and
-		    soft start are active all the time.
-
-		    0 = Set initial mode to low power mode (LPM).
-
-- qcom,ocp-max-retries:
-	Usage: optional
-	Value type: <u32>
-	Description: Maximum number of times to try toggling a voltage switch
-		     off and back on as a result of consecutive over current
-		     events.
-
-- qcom,ocp-retry-delay:
-	Usage: optional
-	Value type: <u32>
-	Description: Time to delay in milliseconds between each voltage switch
-		     toggle after an over current event takes place.
-
-- qcom,pin-ctrl-enable:
-	Usage: optional
-	Value type: <u32>
-	Description: Bit mask specifying which hardware pins should be used to
-		     enable the regulator, if any; supported bits are:
-			0 = ignore all hardware enable signals
-			BIT(0) = follow HW0_EN signal
-			BIT(1) = follow HW1_EN signal
-			BIT(2) = follow HW2_EN signal
-			BIT(3) = follow HW3_EN signal
-
-- qcom,pin-ctrl-hpm:
-	Usage: optional
-	Value type: <u32>
-	Description: Bit mask specifying which hardware pins should be used to
-		     force the regulator into high power mode, if any;
-		     supported bits are:
-			0 = ignore all hardware enable signals
-			BIT(0) = follow HW0_EN signal
-			BIT(1) = follow HW1_EN signal
-			BIT(2) = follow HW2_EN signal
-			BIT(3) = follow HW3_EN signal
-			BIT(4) = follow PMIC awake state
-
-- qcom,vs-soft-start-strength:
-	Usage: optional
-	Value type: <u32>
-	Description: This property sets the soft start strength for voltage
-		     switch type regulators; supported values are:
-			0 = 0.05 uA
-			1 = 0.25 uA
-			2 = 0.55 uA
-			3 = 0.75 uA
-
-- qcom,saw-slave:
-	Usage: optional
-	Value type: <boo>
-	Description: SAW controlled gang slave. Will not be configured.
-
-- qcom,saw-leader:
-	Usage: optional
-	Value type: <boo>
-	Description: SAW controlled gang leader. Will be configured as
-		     SAW regulator.
-
-Example:
-
-	regulators {
-		compatible = "qcom,pm8941-regulators";
-		vdd_l1_l3-supply = <&s1>;
-
-		s1: s1 {
-			regulator-min-microvolt = <1300000>;
-			regulator-max-microvolt = <1400000>;
-		};
-
-		...
-
-		l1: l1 {
-			regulator-min-microvolt = <1225000>;
-			regulator-max-microvolt = <1300000>;
-		};
-
-		....
-	};
-
-Example 2:
-
-	saw3: syscon@9A10000 {
-		compatible = "syscon";
-		reg = <0x9A10000 0x1000>;
-	};
-
-	...
-
-	spm-regulators {
-		compatible = "qcom,pm8994-regulators";
-		qcom,saw-reg = <&saw3>;
-		s8 {
-			qcom,saw-slave;
-		};
-		s9 {
-			qcom,saw-slave;
-		};
-		s10 {
-			qcom,saw-slave;
-		};
-		pm8994_s11_saw: s11 {
-			qcom,saw-leader;
-			regulator-always-on;
-			regulator-min-microvolt = <900000>;
-			regulator-max-microvolt = <1140000>;
-		};
-	};
diff --git a/dts/Bindings/regulator/qcom,spmi-regulator.yaml b/dts/Bindings/regulator/qcom,spmi-regulator.yaml
new file mode 100644
index 0000000000..8b7c4af4b5
--- /dev/null
+++ b/dts/Bindings/regulator/qcom,spmi-regulator.yaml
@@ -0,0 +1,323 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/regulator/qcom,spmi-regulator.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm SPMI Regulators
+
+maintainers:
+  - Robert Marko <robimarko@gmail.com>
+
+properties:
+  compatible:
+    enum:
+      - qcom,pm660-regulators
+      - qcom,pm660l-regulators
+      - qcom,pm8004-regulators
+      - qcom,pm8005-regulators
+      - qcom,pm8226-regulators
+      - qcom,pm8841-regulators
+      - qcom,pm8916-regulators
+      - qcom,pm8941-regulators
+      - qcom,pm8950-regulators
+      - qcom,pm8994-regulators
+      - qcom,pmi8994-regulators
+      - qcom,pmp8074-regulators
+      - qcom,pms405-regulators
+
+  qcom,saw-reg:
+    description: Reference to syscon node defining the SAW registers
+    $ref: /schemas/types.yaml#/definitions/phandle
+
+patternProperties:
+  "^(5vs[1-2]|(l|s)[1-9][0-9]?|lvs[1-3])$":
+    description: List of regulators and its properties
+    type: object
+    $ref: regulator.yaml#
+
+    properties:
+      qcom,ocp-max-retries:
+        description:
+          Maximum number of times to try toggling a voltage switch off and
+          back on as a result of consecutive over current events
+        $ref: /schemas/types.yaml#/definitions/uint32
+
+      qcom,ocp-retry-delay:
+        description:
+          Time to delay in milliseconds between each voltage switch toggle
+          after an over current event takes place
+        $ref: /schemas/types.yaml#/definitions/uint32
+
+      qcom,pin-ctrl-enable:
+        description:
+          Bit mask specifying which hardware pins should be used to enable the
+          regulator, if any.
+          Supported bits are
+          0 = ignore all hardware enable signals
+          BIT(0) = follow HW0_EN signal
+          BIT(1) = follow HW1_EN signal
+          BIT(2) = follow HW2_EN signal
+          BIT(3) = follow HW3_EN signal
+        $ref: /schemas/types.yaml#/definitions/uint32
+        minimum: 0
+        maximum: 15
+
+      qcom,pin-ctrl-hpm:
+        description:
+          Bit mask specifying which hardware pins should be used to force the
+          regulator into high power mode, if any.
+          Supported bits are
+          0 = ignore all hardware enable signals
+          BIT(0) = follow HW0_EN signal
+          BIT(1) = follow HW1_EN signal
+          BIT(2) = follow HW2_EN signal
+          BIT(3) = follow HW3_EN signal
+          BIT(4) = follow PMIC awake state
+        $ref: /schemas/types.yaml#/definitions/uint32
+        minimum: 0
+        maximum: 31
+
+      qcom,vs-soft-start-strength:
+        description:
+          This property sets the soft start strength for voltage switch type
+          regulators.
+          Supported values are
+          0 = 0.05 uA
+          1 = 0.25 uA
+          2 = 0.55 uA
+          3 = 0.75 uA
+        $ref: /schemas/types.yaml#/definitions/uint32
+        minimum: 0
+        maximum: 3
+
+      qcom,saw-slave:
+        description: SAW controlled gang slave. Will not be configured.
+        type: boolean
+
+      qcom,saw-leader:
+        description:
+          SAW controlled gang leader. Will be configured as SAW regulator.
+        type: boolean
+
+      unevaluatedProperties: false
+
+required:
+  - compatible
+
+allOf:
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - qcom,pm660-regulators
+    then:
+      properties:
+        vdd_l15_l16_l17_l18_l19-supply: true
+        vdd_l1_l6_l7-supply: true
+        vdd_l2_l3-supply: true
+        vdd_l5-supply: true
+        vdd_l8_l9_l10_l11_l12_l13_l14-supply: true
+      patternProperties:
+        "^vdd_s[1-6]-supply$": true
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - qcom,pm660l-regulators
+    then:
+      properties:
+        vdd_l1_l9_l10-supply: true
+        vdd_l2-supply: true
+        vdd_l3_l5_l7_l8-supply: true
+        vdd_l4_l6-supply: true
+      patternProperties:
+        "^vdd_s[1-5]-supply$": true
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - qcom,pm8004-regulators
+    then:
+      patternProperties:
+        "^vdd_s[25]-supply$": true
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - qcom,pm8005-regulators
+    then:
+      patternProperties:
+        "^vdd_s[1-4]-supply$": true
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - qcom,pm8226-regulators
+    then:
+      properties:
+        vdd_l10_l11_l13-supply: true
+        vdd_l12_l14-supply: true
+        vdd_l15_l16_l17_l18-supply: true
+        vdd_l19_l20_l21_l22_l23_l28-supply: true
+        vdd_l1_l2_l4_l5-supply: true
+        vdd_l25-supply: true
+        vdd_l3_l24_l26-supply: true
+        vdd_l6_l7_l8_l9_l27-supply: true
+        vdd_lvs1-supply: true
+      patternProperties:
+        "^vdd_s[1-5]-supply$": true
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - qcom,pm8841-regulators
+    then:
+      patternProperties:
+        "^vdd_s[1-8]-supply$": true
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - qcom,pm8916-regulators
+    then:
+      properties:
+        vdd_l1_l3-supply: true
+        vdd_l4_l5_l6-supply: true
+        vdd_l8_l11_l14_l15_l16-supply: true
+        vdd_l9_l10_l12_l13_l17_l18-supply: true
+      patternProperties:
+        "^vdd_l[27]-supply$": true
+        "^vdd_s[1-4]-supply$": true
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - qcom,pm8941-regulators
+    then:
+      properties:
+        interrupts:
+          items:
+            - description: Over-current protection interrupt for 5V S1
+            - description: Over-current protection interrupt for 5V S2
+        interrupt-names:
+          items:
+            - const: ocp-5vs1
+            - const: ocp-5vs2
+        vdd_l13_l20_l23_l24-supply: true
+        vdd_l1_l3-supply: true
+        vdd_l21-supply: true
+        vdd_l2_lvs_1_2_3-supply: true
+        vdd_l4_l11-supply: true
+        vdd_l5_l7-supply: true
+        vdd_l6_l12_l14_l15-supply: true
+        vdd_l8_l16_l18_19-supply: true
+        vdd_l9_l10_l17_l22-supply: true
+        vin_5vs-supply: true
+      patternProperties:
+        "^vdd_s[1-3]-supply$": true
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - qcom,pm8950-regulators
+    then:
+      properties:
+        vdd_l1_l19-supply: true
+        vdd_l20-supply: true
+        vdd_l21-supply: true
+        vdd_l2_l23-supply: true
+        vdd_l3-supply: true
+        vdd_l4_l5_l6_l7_l16-supply: true
+        vdd_l8_l11_l12_l17_l22-supply: true
+        vdd_l9_l10_l13_l14_l15_l18-supply: true
+      patternProperties:
+        "^vdd_s[1-6]-supply$": true
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - qcom,pm8994-regulators
+    then:
+      properties:
+        vdd_l1-supply: true
+        vdd_l13_l19_l23_l24-supply: true
+        vdd_l14_l15-supply: true
+        vdd_l17_l29-supply: true
+        vdd_l20_l21-supply: true
+        vdd_l25-supply: true
+        vdd_l2_l26_l28-supply: true
+        vdd_l3_l11-supply: true
+        vdd_l4_l27_l31-supply: true
+        vdd_l5_l7-supply: true
+        vdd_l6_l12_l32-supply: true
+        vdd_l8_l16_l30-supply: true
+        vdd_l9_l10_l18_l22-supply: true
+        vdd_lvs_1_2-supply: true
+      patternProperties:
+        "^vdd_s[1-9][0-2]?-supply$": true
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - qcom,pmi8994-regulators
+    then:
+      properties:
+        vdd_l1-supply: true
+      patternProperties:
+        "^vdd_s[1-3]-supply$": true
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - qcom,pmp8074-regulators
+    then:
+      properties:
+        vdd_l10_l11_l12_l13-supply: true
+        vdd_l1_l2-supply: true
+        vdd_l3_l8-supply: true
+        vdd_l5_l6_l15-supply: true
+      patternProperties:
+        "^vdd_l[479]-supply$": true
+        "^vdd_s[1-5]-supply$": true
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - qcom,pms405-regulators
+    then:
+      properties:
+        vdd_s3-supply: true
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    regulators {
+      compatible = "qcom,pm8941-regulators";
+      vdd_l1_l3-supply = <&s1>;
+
+      s1: s1 {
+        regulator-min-microvolt = <1300000>;
+        regulator-max-microvolt = <1400000>;
+      };
+
+      l1: l1 {
+        regulator-min-microvolt = <1225000>;
+        regulator-max-microvolt = <1300000>;
+      };
+    };
+...
diff --git a/dts/Bindings/regulator/regulator.yaml b/dts/Bindings/regulator/regulator.yaml
index a9b66ececc..6e8aa9eed3 100644
--- a/dts/Bindings/regulator/regulator.yaml
+++ b/dts/Bindings/regulator/regulator.yaml
@@ -23,6 +23,7 @@ properties:
 
   regulator-microvolt-offset:
     description: Offset applied to voltages to compensate for voltage drops
+    $ref: "/schemas/types.yaml#/definitions/uint32"
 
   regulator-min-microamp:
     description: smallest current consumers may set