dts: update to v4.8-rc1

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

18 files changed, 899 insertions, 4 deletions

diff --git a/dts/Bindings/soc/fsl/cpm_qe/cpm.txt b/dts/Bindings/soc/fsl/cpm_qe/cpm.txt
new file mode 100644
index 0000000000..160c752484
--- /dev/null
+++ b/dts/Bindings/soc/fsl/cpm_qe/cpm.txt
@@ -0,0 +1,67 @@
+* Freescale Communications Processor Module
+
+NOTE: This is an interim binding, and will likely change slightly,
+as more devices are supported.  The QE bindings especially are
+incomplete.
+
+* Root CPM node
+
+Properties:
+- compatible : "fsl,cpm1", "fsl,cpm2", or "fsl,qe".
+- reg : A 48-byte region beginning with CPCR.
+
+Example:
+     cpm@119c0 {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	#interrupt-cells = <2>;
+	compatible = "fsl,mpc8272-cpm", "fsl,cpm2";
+	reg = <119c0 30>;
+     }
+
+* Properties common to multiple CPM/QE devices
+
+- fsl,cpm-command : This value is ORed with the opcode and command flag
+                    to specify the device on which a CPM command operates.
+
+- fsl,cpm-brg : Indicates which baud rate generator the device
+                is associated with.  If absent, an unused BRG
+                should be dynamically allocated.  If zero, the
+                device uses an external clock rather than a BRG.
+
+- reg : Unless otherwise specified, the first resource represents the
+        scc/fcc/ucc registers, and the second represents the device's
+        parameter RAM region (if it has one).
+
+* Multi-User RAM (MURAM)
+
+The multi-user/dual-ported RAM is expressed as a bus under the CPM node.
+
+Ranges must be set up subject to the following restrictions:
+
+- Children's reg nodes must be offsets from the start of all muram, even
+  if the user-data area does not begin at zero.
+- If multiple range entries are used, the difference between the parent
+  address and the child address must be the same in all, so that a single
+  mapping can cover them all while maintaining the ability to determine
+  CPM-side offsets with pointer subtraction.  It is recommended that
+  multiple range entries not be used.
+- A child address of zero must be translatable, even if no reg resources
+  contain it.
+
+A child "data" node must exist, compatible with "fsl,cpm-muram-data", to
+indicate the portion of muram that is usable by the OS for arbitrary
+purposes.  The data node may have an arbitrary number of reg resources,
+all of which contribute to the allocatable muram pool.
+
+Example, based on mpc8272:
+	muram@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0 10000>;
+
+		data@0 {
+			compatible = "fsl,cpm-muram-data";
+			reg = <0 2000 9800 800>;
+		};
+	};
diff --git a/dts/Bindings/soc/fsl/cpm_qe/cpm/brg.txt b/dts/Bindings/soc/fsl/cpm_qe/cpm/brg.txt
new file mode 100644
index 0000000000..4c7d45eaf0
--- /dev/null
+++ b/dts/Bindings/soc/fsl/cpm_qe/cpm/brg.txt
@@ -0,0 +1,21 @@
+* Baud Rate Generators
+
+Currently defined compatibles:
+fsl,cpm-brg
+fsl,cpm1-brg
+fsl,cpm2-brg
+
+Properties:
+- reg : There may be an arbitrary number of reg resources; BRG
+  numbers are assigned to these in order.
+- clock-frequency : Specifies the base frequency driving
+  the BRG.
+
+Example:
+	brg@119f0 {
+		compatible = "fsl,mpc8272-brg",
+			     "fsl,cpm2-brg",
+			     "fsl,cpm-brg";
+		reg = <119f0 10 115f0 10>;
+		clock-frequency = <d#25000000>;
+	};
diff --git a/dts/Bindings/soc/fsl/cpm_qe/cpm/i2c.txt b/dts/Bindings/soc/fsl/cpm_qe/cpm/i2c.txt
new file mode 100644
index 0000000000..87bc604866
--- /dev/null
+++ b/dts/Bindings/soc/fsl/cpm_qe/cpm/i2c.txt
@@ -0,0 +1,41 @@
+* I2C
+
+The I2C controller is expressed as a bus under the CPM node.
+
+Properties:
+- compatible : "fsl,cpm1-i2c", "fsl,cpm2-i2c"
+- reg : On CPM2 devices, the second resource doesn't specify the I2C
+  Parameter RAM itself, but the I2C_BASE field of the CPM2 Parameter RAM
+  (typically 0x8afc 0x2).
+- #address-cells : Should be one. The cell is the i2c device address with
+  the r/w bit set to zero.
+- #size-cells : Should be zero.
+- clock-frequency : Can be used to set the i2c clock frequency. If
+  unspecified, a default frequency of 60kHz is being used.
+The following two properties are deprecated. They are only used by legacy
+i2c drivers to find the bus to probe:
+- linux,i2c-index : Can be used to hard code an i2c bus number. By default,
+  the bus number is dynamically assigned by the i2c core.
+- linux,i2c-class : Can be used to override the i2c class. The class is used
+  by legacy i2c device drivers to find a bus in a specific context like
+  system management, video or sound. By default, I2C_CLASS_HWMON (1) is
+  being used. The definition of the classes can be found in
+  include/i2c/i2c.h
+
+Example, based on mpc823:
+
+	i2c@860 {
+		compatible = "fsl,mpc823-i2c",
+			     "fsl,cpm1-i2c";
+		reg = <0x860 0x20 0x3c80 0x30>;
+		interrupts = <16>;
+		interrupt-parent = <&CPM_PIC>;
+		fsl,cpm-command = <0x10>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		rtc@68 {
+			compatible = "dallas,ds1307";
+			reg = <0x68>;
+		};
+	};
diff --git a/dts/Bindings/soc/fsl/cpm_qe/cpm/pic.txt b/dts/Bindings/soc/fsl/cpm_qe/cpm/pic.txt
new file mode 100644
index 0000000000..8e3ee16816
--- /dev/null
+++ b/dts/Bindings/soc/fsl/cpm_qe/cpm/pic.txt
@@ -0,0 +1,18 @@
+* Interrupt Controllers
+
+Currently defined compatibles:
+- fsl,cpm1-pic
+  - only one interrupt cell
+- fsl,pq1-pic
+- fsl,cpm2-pic
+  - second interrupt cell is level/sense:
+    - 2 is falling edge
+    - 8 is active low
+
+Example:
+	interrupt-controller@10c00 {
+		#interrupt-cells = <2>;
+		interrupt-controller;
+		reg = <10c00 80>;
+		compatible = "mpc8272-pic", "fsl,cpm2-pic";
+	};
diff --git a/dts/Bindings/soc/fsl/cpm_qe/cpm/usb.txt b/dts/Bindings/soc/fsl/cpm_qe/cpm/usb.txt
new file mode 100644
index 0000000000..74bfda4bb8
--- /dev/null
+++ b/dts/Bindings/soc/fsl/cpm_qe/cpm/usb.txt
@@ -0,0 +1,15 @@
+* USB (Universal Serial Bus Controller)
+
+Properties:
+- compatible : "fsl,cpm1-usb", "fsl,cpm2-usb", "fsl,qe-usb"
+
+Example:
+	usb@11bc0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "fsl,cpm2-usb";
+		reg = <11b60 18 8b00 100>;
+		interrupts = <b 8>;
+		interrupt-parent = <&PIC>;
+		fsl,cpm-command = <2e600000>;
+	};
diff --git a/dts/Bindings/soc/fsl/cpm_qe/gpio.txt b/dts/Bindings/soc/fsl/cpm_qe/gpio.txt
new file mode 100644
index 0000000000..349f79fd70
--- /dev/null
+++ b/dts/Bindings/soc/fsl/cpm_qe/gpio.txt
@@ -0,0 +1,38 @@
+Every GPIO controller node must have #gpio-cells property defined,
+this information will be used to translate gpio-specifiers.
+
+On CPM1 devices, all ports are using slightly different register layouts.
+Ports A, C and D are 16bit ports and Ports B and E are 32bit ports.
+
+On CPM2 devices, all ports are 32bit ports and use a common register layout.
+
+Required properties:
+- compatible : "fsl,cpm1-pario-bank-a", "fsl,cpm1-pario-bank-b",
+  "fsl,cpm1-pario-bank-c", "fsl,cpm1-pario-bank-d",
+  "fsl,cpm1-pario-bank-e", "fsl,cpm2-pario-bank"
+- #gpio-cells : Should be two. The first cell is the pin number and the
+  second cell is used to specify optional parameters (currently unused).
+- gpio-controller : Marks the port as GPIO controller.
+
+Example of three SOC GPIO banks defined as gpio-controller nodes:
+
+	CPM1_PIO_A: gpio-controller@950 {
+		#gpio-cells = <2>;
+		compatible = "fsl,cpm1-pario-bank-a";
+		reg = <0x950 0x10>;
+		gpio-controller;
+	};
+
+	CPM1_PIO_B: gpio-controller@ab8 {
+		#gpio-cells = <2>;
+		compatible = "fsl,cpm1-pario-bank-b";
+		reg = <0xab8 0x10>;
+		gpio-controller;
+	};
+
+	CPM1_PIO_E: gpio-controller@ac8 {
+		#gpio-cells = <2>;
+		compatible = "fsl,cpm1-pario-bank-e";
+		reg = <0xac8 0x18>;
+		gpio-controller;
+	};
diff --git a/dts/Bindings/soc/fsl/cpm_qe/network.txt b/dts/Bindings/soc/fsl/cpm_qe/network.txt
new file mode 100644
index 0000000000..03c741602c
--- /dev/null
+++ b/dts/Bindings/soc/fsl/cpm_qe/network.txt
@@ -0,0 +1,124 @@
+* Network
+
+Currently defined compatibles:
+- fsl,cpm1-scc-enet
+- fsl,cpm2-scc-enet
+- fsl,cpm1-fec-enet
+- fsl,cpm2-fcc-enet (third resource is GFEMR)
+- fsl,qe-enet
+
+Example:
+
+	ethernet@11300 {
+		compatible = "fsl,mpc8272-fcc-enet",
+			     "fsl,cpm2-fcc-enet";
+		reg = <11300 20 8400 100 11390 1>;
+		local-mac-address = [ 00 00 00 00 00 00 ];
+		interrupts = <20 8>;
+		interrupt-parent = <&PIC>;
+		phy-handle = <&PHY0>;
+		fsl,cpm-command = <12000300>;
+	};
+
+* MDIO
+
+Currently defined compatibles:
+fsl,pq1-fec-mdio (reg is same as first resource of FEC device)
+fsl,cpm2-mdio-bitbang (reg is port C registers)
+
+Properties for fsl,cpm2-mdio-bitbang:
+fsl,mdio-pin : pin of port C controlling mdio data
+fsl,mdc-pin : pin of port C controlling mdio clock
+
+Example:
+	mdio@10d40 {
+		compatible = "fsl,mpc8272ads-mdio-bitbang",
+			     "fsl,mpc8272-mdio-bitbang",
+			     "fsl,cpm2-mdio-bitbang";
+		reg = <10d40 14>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		fsl,mdio-pin = <12>;
+		fsl,mdc-pin = <13>;
+	};
+
+* HDLC
+
+Currently defined compatibles:
+- fsl,ucc-hdlc
+
+Properties for fsl,ucc-hdlc:
+- rx-clock-name
+- tx-clock-name
+	Usage: required
+	Value type: <string>
+	Definition : Must be "brg1"-"brg16" for internal clock source,
+		     Must be "clk1"-"clk24" for external clock source.
+
+- fsl,tdm-interface
+	Usage: optional
+	Value type: <empty>
+	Definition : Specify that hdlc is based on tdm-interface
+
+The property below is dependent on fsl,tdm-interface:
+- fsl,rx-sync-clock
+	Usage: required
+	Value type: <string>
+	Definition : Must be "none", "rsync_pin", "brg9-11" and "brg13-15".
+
+- fsl,tx-sync-clock
+	Usage: required
+	Value type: <string>
+	Definition : Must be "none", "tsync_pin", "brg9-11" and "brg13-15".
+
+- fsl,tdm-framer-type
+	Usage: required for tdm interface
+	Value type: <string>
+	Definition : "e1" or "t1".Now e1 and t1 are used, other framer types
+		     are not supported.
+
+- fsl,tdm-id
+	Usage: required for tdm interface
+	Value type: <u32>
+	Definition : number of TDM ID
+
+- fsl,tx-timeslot-mask
+- fsl,rx-timeslot-mask
+	Usage: required for tdm interface
+	Value type: <u32>
+	Definition : time slot mask for TDM operation. Indicates which time
+		     slots used for transmitting and receiving.
+
+- fsl,siram-entry-id
+	Usage: required for tdm interface
+	Value type: <u32>
+	Definition : Must be 0,2,4...64. the number of TDM entry.
+
+- fsl,tdm-internal-loopback
+	usage: optional for tdm interface
+	value type: <empty>
+	Definition : Internal loopback connecting on TDM layer.
+
+Example for tdm interface:
+
+	ucc@2000 {
+		compatible = "fsl,ucc-hdlc";
+		rx-clock-name = "clk8";
+		tx-clock-name = "clk9";
+		fsl,rx-sync-clock = "rsync_pin";
+		fsl,tx-sync-clock = "tsync_pin";
+		fsl,tx-timeslot-mask = <0xfffffffe>;
+		fsl,rx-timeslot-mask = <0xfffffffe>;
+		fsl,tdm-framer-type = "e1";
+		fsl,tdm-id = <0>;
+		fsl,siram-entry-id = <0>;
+		fsl,tdm-interface;
+	};
+
+Example for hdlc without tdm interface:
+
+	ucc@2000 {
+		compatible = "fsl,ucc-hdlc";
+		rx-clock-name = "brg1";
+		tx-clock-name = "brg1";
+	};
diff --git a/dts/Bindings/soc/fsl/cpm_qe/qe.txt b/dts/Bindings/soc/fsl/cpm_qe/qe.txt
new file mode 100644
index 0000000000..d7afaff5fa
--- /dev/null
+++ b/dts/Bindings/soc/fsl/cpm_qe/qe.txt
@@ -0,0 +1,167 @@
+* Freescale QUICC Engine module (QE)
+This represents qe module that is installed on PowerQUICC II Pro.
+
+NOTE:  This is an interim binding; it should be updated to fit
+in with the CPM binding later in this document.
+
+Basically, it is a bus of devices, that could act more or less
+as a complete entity (UCC, USB etc ). All of them should be siblings on
+the "root" qe node, using the common properties from there.
+The description below applies to the qe of MPC8360 and
+more nodes and properties would be extended in the future.
+
+i) Root QE device
+
+Required properties:
+- compatible : should be "fsl,qe";
+- model : precise model of the QE, Can be "QE", "CPM", or "CPM2"
+- reg : offset and length of the device registers.
+- bus-frequency : the clock frequency for QUICC Engine.
+- fsl,qe-num-riscs: define how many RISC engines the QE has.
+- fsl,qe-num-snums: define how many serial number(SNUM) the QE can use for the
+  threads.
+
+Optional properties:
+- fsl,firmware-phandle:
+    Usage: required only if there is no fsl,qe-firmware child node
+    Value type: <phandle>
+    Definition: Points to a firmware node (see "QE Firmware Node" below)
+        that contains the firmware that should be uploaded for this QE.
+        The compatible property for the firmware node should say,
+        "fsl,qe-firmware".
+
+Recommended properties
+- brg-frequency : the internal clock source frequency for baud-rate
+  generators in Hz.
+
+Example:
+     qe@e0100000 {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	#interrupt-cells = <2>;
+	compatible = "fsl,qe";
+	ranges = <0 e0100000 00100000>;
+	reg = <e0100000 480>;
+	brg-frequency = <0>;
+	bus-frequency = <179A7B00>;
+     }
+
+* Multi-User RAM (MURAM)
+
+Required properties:
+- compatible : should be "fsl,qe-muram", "fsl,cpm-muram".
+- mode : the could be "host" or "slave".
+- ranges : Should be defined as specified in 1) to describe the
+   translation of MURAM addresses.
+- data-only : sub-node which defines the address area under MURAM
+   bus that can be allocated as data/parameter
+
+Example:
+
+     muram@10000 {
+	compatible = "fsl,qe-muram", "fsl,cpm-muram";
+	ranges = <0 00010000 0000c000>;
+
+	data-only@0{
+		compatible = "fsl,qe-muram-data",
+			     "fsl,cpm-muram-data";
+		reg = <0 c000>;
+	};
+     };
+
+* Interrupt Controller (IC)
+
+Required properties:
+- compatible : should be "fsl,qe-ic".
+- reg : Address range of IC register set.
+- interrupts : interrupts generated by the device.
+- interrupt-controller : this device is a interrupt controller.
+
+Example:
+
+	qeic: interrupt-controller@80 {
+		interrupt-controller;
+		compatible = "fsl,qe-ic";
+		#address-cells = <0>;
+		#interrupt-cells = <1>;
+		reg = <0x80 0x80>;
+		interrupts = <95 2 0 0  94 2 0 0>;
+	};
+
+* Serial Interface Block (SI)
+
+The SI manages the routing of eight TDM lines to the QE block serial drivers
+, the MCC and the UCCs, for receive and transmit.
+
+Required properties:
+- compatible : must be "fsl,<chip>-qe-si". For t1040, must contain
+  "fsl,t1040-qe-si".
+- reg : Address range of SI register set.
+
+Example:
+
+	si1: si@700 {
+		compatible = "fsl,t1040-qe-si";
+		reg = <0x700 0x80>;
+	};
+
+* Serial Interface Block RAM(SIRAM)
+
+store the routing entries of SI
+
+Required properties:
+- compatible : should be "fsl,<chip>-qe-siram". For t1040, must contain
+  "fsl,t1040-qe-siram".
+- reg : Address range of SI RAM.
+
+Example:
+
+	siram1: siram@1000 {
+		compatible = "fsl,t1040-qe-siram";
+		reg = <0x1000 0x800>;
+	};
+
+* QE Firmware Node
+
+This node defines a firmware binary that is embedded in the device tree, for
+the purpose of passing the firmware from bootloader to the kernel, or from
+the hypervisor to the guest.
+
+The firmware node itself contains the firmware binary contents, a compatible
+property, and any firmware-specific properties.  The node should be placed
+inside a QE node that needs it.  Doing so eliminates the need for a
+fsl,firmware-phandle property.  Other QE nodes that need the same firmware
+should define an fsl,firmware-phandle property that points to the firmware node
+in the first QE node.
+
+The fsl,firmware property can be specified in the DTS (possibly using incbin)
+or can be inserted by the boot loader at boot time.
+
+Required properties:
+  - compatible
+      Usage: required
+      Value type: <string>
+      Definition: A standard property.  Specify a string that indicates what
+          kind of firmware it is.  For QE, this should be "fsl,qe-firmware".
+
+   - fsl,firmware
+      Usage: required
+      Value type: <prop-encoded-array>, encoded as an array of bytes
+      Definition: A standard property.  This property contains the firmware
+          binary "blob".
+
+Example:
+	qe1@e0080000 {
+		compatible = "fsl,qe";
+		qe_firmware:qe-firmware {
+			compatible = "fsl,qe-firmware";
+			fsl,firmware = [0x70 0xcd 0x00 0x00 0x01 0x46 0x45 ...];
+		};
+		...
+	};
+
+	qe2@e0090000 {
+		compatible = "fsl,qe";
+		fsl,firmware-phandle = <&qe_firmware>;
+		...
+	};
diff --git a/dts/Bindings/soc/fsl/cpm_qe/qe/firmware.txt b/dts/Bindings/soc/fsl/cpm_qe/qe/firmware.txt
new file mode 100644
index 0000000000..249db3a15d
--- /dev/null
+++ b/dts/Bindings/soc/fsl/cpm_qe/qe/firmware.txt
@@ -0,0 +1,24 @@
+* Uploaded QE firmware
+
+      If a new firmware has been uploaded to the QE (usually by the
+      boot loader), then a 'firmware' child node should be added to the QE
+      node.  This node provides information on the uploaded firmware that
+      device drivers may need.
+
+      Required properties:
+      - id: The string name of the firmware.  This is taken from the 'id'
+            member of the qe_firmware structure of the uploaded firmware.
+            Device drivers can search this string to determine if the
+            firmware they want is already present.
+      - extended-modes: The Extended Modes bitfield, taken from the
+		   firmware binary.  It is a 64-bit number represented
+		   as an array of two 32-bit numbers.
+      - virtual-traps: The virtual traps, taken from the firmware binary.
+		  It is an array of 8 32-bit numbers.
+
+Example:
+	firmware {
+		id = "Soft-UART";
+		extended-modes = <0 0>;
+		virtual-traps = <0 0 0 0 0 0 0 0>;
+	};
diff --git a/dts/Bindings/soc/fsl/cpm_qe/qe/par_io.txt b/dts/Bindings/soc/fsl/cpm_qe/qe/par_io.txt
new file mode 100644
index 0000000000..6098426020
--- /dev/null
+++ b/dts/Bindings/soc/fsl/cpm_qe/qe/par_io.txt
@@ -0,0 +1,51 @@
+* Parallel I/O Ports
+
+This node configures Parallel I/O ports for CPUs with QE support.
+The node should reside in the "soc" node of the tree.  For each
+device that using parallel I/O ports, a child node should be created.
+See the definition of the Pin configuration nodes below for more
+information.
+
+Required properties:
+- device_type : should be "par_io".
+- reg : offset to the register set and its length.
+- num-ports : number of Parallel I/O ports
+
+Example:
+par_io@1400 {
+	reg = <1400 100>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	device_type = "par_io";
+	num-ports = <7>;
+	ucc_pin@01 {
+		......
+	};
+
+Note that "par_io" nodes are obsolete, and should not be used for
+the new device trees. Instead, each Par I/O bank should be represented
+via its own gpio-controller node:
+
+Required properties:
+- #gpio-cells : should be "2".
+- compatible : should be "fsl,<chip>-qe-pario-bank",
+  "fsl,mpc8323-qe-pario-bank".
+- reg : offset to the register set and its length.
+- gpio-controller : node to identify gpio controllers.
+
+Example:
+	qe_pio_a: gpio-controller@1400 {
+		#gpio-cells = <2>;
+		compatible = "fsl,mpc8360-qe-pario-bank",
+		"fsl,mpc8323-qe-pario-bank";
+		reg = <0x1400 0x18>;
+		gpio-controller;
+	  };
+
+	qe_pio_e: gpio-controller@1460 {
+		#gpio-cells = <2>;
+		compatible = "fsl,mpc8360-qe-pario-bank",
+			     "fsl,mpc8323-qe-pario-bank";
+		reg = <0x1460 0x18>;
+		gpio-controller;
+	  };
diff --git a/dts/Bindings/soc/fsl/cpm_qe/qe/pincfg.txt b/dts/Bindings/soc/fsl/cpm_qe/qe/pincfg.txt
new file mode 100644
index 0000000000..ec6ee2e864
--- /dev/null
+++ b/dts/Bindings/soc/fsl/cpm_qe/qe/pincfg.txt
@@ -0,0 +1,57 @@
+* Pin configuration nodes
+
+Required properties:
+- pio-map : array of pin configurations.  Each pin is defined by 6
+  integers.  The six numbers are respectively: port, pin, dir,
+  open_drain, assignment, has_irq.
+  - port : port number of the pin; 0-6 represent port A-G in UM.
+  - pin : pin number in the port.
+  - dir : direction of the pin, should encode as follows:
+
+     0 = The pin is disabled
+     1 = The pin is an output
+     2 = The pin is an input
+     3 = The pin is I/O
+
+  - open_drain : indicates the pin is normal or wired-OR:
+
+     0 = The pin is actively driven as an output
+     1 = The pin is an open-drain driver. As an output, the pin is
+         driven active-low, otherwise it is three-stated.
+
+  - assignment : function number of the pin according to the Pin Assignment
+    tables in User Manual.  Each pin can have up to 4 possible functions in
+    QE and two options for CPM.
+  - has_irq : indicates if the pin is used as source of external
+    interrupts.
+
+Example:
+     ucc_pin@01 {
+	pio-map = <
+	/* port  pin  dir  open_drain  assignment  has_irq */
+		0  3  1  0  1  0 	/* TxD0 */
+		0  4  1  0  1  0 	/* TxD1 */
+		0  5  1  0  1  0 	/* TxD2 */
+		0  6  1  0  1  0 	/* TxD3 */
+		1  6  1  0  3  0 	/* TxD4 */
+		1  7  1  0  1  0 	/* TxD5 */
+		1  9  1  0  2  0 	/* TxD6 */
+		1  a  1  0  2  0 	/* TxD7 */
+		0  9  2  0  1  0 	/* RxD0 */
+		0  a  2  0  1  0 	/* RxD1 */
+		0  b  2  0  1  0 	/* RxD2 */
+		0  c  2  0  1  0 	/* RxD3 */
+		0  d  2  0  1  0 	/* RxD4 */
+		1  1  2  0  2  0 	/* RxD5 */
+		1  0  2  0  2  0 	/* RxD6 */
+		1  4  2  0  2  0 	/* RxD7 */
+		0  7  1  0  1  0 	/* TX_EN */
+		0  8  1  0  1  0 	/* TX_ER */
+		0  f  2  0  1  0 	/* RX_DV */
+		0  10 2  0  1  0 	/* RX_ER */
+		0  0  2  0  1  0 	/* RX_CLK */
+		2  9  1  0  3  0 	/* GTX_CLK - CLK10 */
+		2  8  2  0  1  0>;	/* GTX125 - CLK9 */
+     };
+
+
diff --git a/dts/Bindings/soc/fsl/cpm_qe/qe/ucc.txt b/dts/Bindings/soc/fsl/cpm_qe/qe/ucc.txt
new file mode 100644
index 0000000000..e47734bee3
--- /dev/null
+++ b/dts/Bindings/soc/fsl/cpm_qe/qe/ucc.txt
@@ -0,0 +1,70 @@
+* UCC (Unified Communications Controllers)
+
+Required properties:
+- device_type : should be "network", "hldc", "uart", "transparent"
+  "bisync", "atm", or "serial".
+- compatible : could be "ucc_geth" or "fsl_atm" and so on.
+- cell-index : the ucc number(1-8), corresponding to UCCx in UM.
+- reg : Offset and length of the register set for the device
+- interrupts : <a b> where a is the interrupt number and b is a
+  field that represents an encoding of the sense and level
+  information for the interrupt.  This should be encoded based on
+  the information in section 2) depending on the type of interrupt
+  controller you have.
+- interrupt-parent : the phandle for the interrupt controller that
+  services interrupts for this device.
+- pio-handle : The phandle for the Parallel I/O port configuration.
+- port-number : for UART drivers, the port number to use, between 0 and 3.
+  This usually corresponds to the /dev/ttyQE device, e.g. <0> = /dev/ttyQE0.
+  The port number is added to the minor number of the device.  Unlike the
+  CPM UART driver, the port-number is required for the QE UART driver.
+- soft-uart : for UART drivers, if specified this means the QE UART device
+  driver should use "Soft-UART" mode, which is needed on some SOCs that have
+  broken UART hardware.  Soft-UART is provided via a microcode upload.
+- rx-clock-name: the UCC receive clock source
+  "none": clock source is disabled
+  "brg1" through "brg16": clock source is BRG1-BRG16, respectively
+  "clk1" through "clk24": clock source is CLK1-CLK24, respectively
+- tx-clock-name: the UCC transmit clock source
+  "none": clock source is disabled
+  "brg1" through "brg16": clock source is BRG1-BRG16, respectively
+  "clk1" through "clk24": clock source is CLK1-CLK24, respectively
+The following two properties are deprecated.  rx-clock has been replaced
+with rx-clock-name, and tx-clock has been replaced with tx-clock-name.
+Drivers that currently use the deprecated properties should continue to
+do so, in order to support older device trees, but they should be updated
+to check for the new properties first.
+- rx-clock : represents the UCC receive clock source.
+  0x00 : clock source is disabled;
+  0x1~0x10 : clock source is BRG1~BRG16 respectively;
+  0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively.
+- tx-clock: represents the UCC transmit clock source;
+  0x00 : clock source is disabled;
+  0x1~0x10 : clock source is BRG1~BRG16 respectively;
+  0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively.
+
+Required properties for network device_type:
+- mac-address : list of bytes representing the ethernet address.
+- phy-handle : The phandle for the PHY connected to this controller.
+
+Recommended properties:
+- phy-connection-type : a string naming the controller/PHY interface type,
+  i.e., "mii" (default), "rmii", "gmii", "rgmii", "rgmii-id" (Internal
+  Delay), "rgmii-txid" (delay on TX only), "rgmii-rxid" (delay on RX only),
+  "tbi", or "rtbi".
+
+Example:
+	ucc@2000 {
+		device_type = "network";
+		compatible = "ucc_geth";
+		cell-index = <1>;
+		reg = <2000 200>;
+		interrupts = <a0 0>;
+		interrupt-parent = <700>;
+		mac-address = [ 00 04 9f 00 23 23 ];
+		rx-clock = "none";
+		tx-clock = "clk9";
+		phy-handle = <212000>;
+		phy-connection-type = "gmii";
+		pio-handle = <140001>;
+	};
diff --git a/dts/Bindings/soc/fsl/cpm_qe/qe/usb.txt b/dts/Bindings/soc/fsl/cpm_qe/qe/usb.txt
new file mode 100644
index 0000000000..9ccd5f3040
--- /dev/null
+++ b/dts/Bindings/soc/fsl/cpm_qe/qe/usb.txt
@@ -0,0 +1,37 @@
+Freescale QUICC Engine USB Controller
+
+Required properties:
+- compatible : should be "fsl,<chip>-qe-usb", "fsl,mpc8323-qe-usb".
+- reg : the first two cells should contain usb registers location and
+  length, the next two two cells should contain PRAM location and
+  length.
+- interrupts : should contain USB interrupt.
+- interrupt-parent : interrupt source phandle.
+- fsl,fullspeed-clock : specifies the full speed USB clock source:
+  "none": clock source is disabled
+  "brg1" through "brg16": clock source is BRG1-BRG16, respectively
+  "clk1" through "clk24": clock source is CLK1-CLK24, respectively
+- fsl,lowspeed-clock : specifies the low speed USB clock source:
+  "none": clock source is disabled
+  "brg1" through "brg16": clock source is BRG1-BRG16, respectively
+  "clk1" through "clk24": clock source is CLK1-CLK24, respectively
+- hub-power-budget : USB power budget for the root hub, in mA.
+- gpios : should specify GPIOs in this order: USBOE, USBTP, USBTN, USBRP,
+  USBRN, SPEED (optional), and POWER (optional).
+
+Example:
+
+usb@6c0 {
+	compatible = "fsl,mpc8360-qe-usb", "fsl,mpc8323-qe-usb";
+	reg = <0x6c0 0x40 0x8b00 0x100>;
+	interrupts = <11>;
+	interrupt-parent = <&qeic>;
+	fsl,fullspeed-clock = "clk21";
+	gpios = <&qe_pio_b  2 0 /* USBOE */
+		 &qe_pio_b  3 0 /* USBTP */
+		 &qe_pio_b  8 0 /* USBTN */
+		 &qe_pio_b  9 0 /* USBRP */
+		 &qe_pio_b 11 0 /* USBRN */
+		 &qe_pio_e 20 0 /* SPEED */
+		 &qe_pio_e 21 0 /* POWER */>;
+};
diff --git a/dts/Bindings/soc/fsl/cpm_qe/serial.txt b/dts/Bindings/soc/fsl/cpm_qe/serial.txt
new file mode 100644
index 0000000000..2ea76d9d13
--- /dev/null
+++ b/dts/Bindings/soc/fsl/cpm_qe/serial.txt
@@ -0,0 +1,32 @@
+* Serial
+
+Currently defined compatibles:
+- fsl,cpm1-smc-uart
+- fsl,cpm2-smc-uart
+- fsl,cpm1-scc-uart
+- fsl,cpm2-scc-uart
+- fsl,qe-uart
+
+Modem control lines connected to GPIO controllers are listed in the gpios
+property as described in booting-without-of.txt, section IX.1 in the following
+order:
+
+CTS, RTS, DCD, DSR, DTR, and RI.
+
+The gpios property is optional and can be left out when control lines are
+not used.
+
+Example:
+
+	serial@11a00 {
+		device_type = "serial";
+		compatible = "fsl,mpc8272-scc-uart",
+			     "fsl,cpm2-scc-uart";
+		reg = <11a00 20 8000 100>;
+		interrupts = <28 8>;
+		interrupt-parent = <&PIC>;
+		fsl,cpm-brg = <1>;
+		fsl,cpm-command = <00800000>;
+		gpios = <&gpio_c 15 0
+			 &gpio_d 29 0>;
+	};
diff --git a/dts/Bindings/soc/fsl/cpm_qe/uqe_serial.txt b/dts/Bindings/soc/fsl/cpm_qe/uqe_serial.txt
new file mode 100644
index 0000000000..8823c86c80
--- /dev/null
+++ b/dts/Bindings/soc/fsl/cpm_qe/uqe_serial.txt
@@ -0,0 +1,17 @@
+* Serial
+
+Required Properties:
+compatible : must be "fsl,<chip>-ucc-uart". For t1040, must be
+"fsl,t1040-ucc-uart".
+port-number : port number of UCC-UART
+tx/rx-clock-name : should be "brg1"-"brg16" for internal clock source,
+		   should be "clk1"-"clk28" for external clock source.
+
+Example:
+
+	ucc_serial: ucc@2200 {
+		compatible = "fsl,t1040-ucc-uart";
+		port-number = <0>;
+		rx-clock-name = "brg2";
+		tx-clock-name = "brg2";
+	};
diff --git a/dts/Bindings/soc/qcom/qcom,smp2p.txt b/dts/Bindings/soc/qcom/qcom,smp2p.txt
index 5cc82b8353..af9ca37221 100644
--- a/dts/Bindings/soc/qcom/qcom,smp2p.txt
+++ b/dts/Bindings/soc/qcom/qcom,smp2p.txt
@@ -68,7 +68,7 @@ important.
 	Value type: <u32>
 	Definition: must be 2 - denoting the bit in the entry and IRQ flags
 
-- #qcom,state-cells:
+- #qcom,smem-state-cells:
 	Usage: required for outgoing entries
 	Value type: <u32>
 	Definition: must be 1 - denoting the bit in the entry
@@ -92,7 +92,7 @@ wcnss-smp2p {
 	wcnss_smp2p_out: master-kernel {
 		qcom,entry-name = "master-kernel";
 
-		#qcom,state-cells = <1>;
+		#qcom,smem-state-cells = <1>;
 	};
 
 	wcnss_smp2p_in: slave-kernel {
diff --git a/dts/Bindings/soc/qcom/qcom,smsm.txt b/dts/Bindings/soc/qcom/qcom,smsm.txt
index a6634c7085..2993b5a97d 100644
--- a/dts/Bindings/soc/qcom/qcom,smsm.txt
+++ b/dts/Bindings/soc/qcom/qcom,smsm.txt
@@ -51,7 +51,7 @@ important.
 	Definition: specifies the offset, in words, of the first bit for this
 		    entry
 
-- #qcom,state-cells:
+- #qcom,smem-state-cells:
 	Usage: required for local entry
 	Value type: <u32>
 	Definition: must be 1 - denotes bit number
@@ -91,7 +91,7 @@ smsm {
 	apps_smsm: apps@0 {
 		reg = <0>;
 
-		#qcom,state-cells = <1>;
+		#qcom,smem-state-cells = <1>;
 	};
 
 	wcnss_smsm: wcnss@7 {
diff --git a/dts/Bindings/soc/qcom/qcom,wcnss.txt b/dts/Bindings/soc/qcom/qcom,wcnss.txt
new file mode 100644
index 0000000000..4ea39e9186
--- /dev/null
+++ b/dts/Bindings/soc/qcom/qcom,wcnss.txt
@@ -0,0 +1,116 @@
+Qualcomm WCNSS Binding
+
+This binding describes the Qualcomm WCNSS hardware. It consists of control
+block and a BT, WiFi and FM radio block, all using SMD as command channels.
+
+- compatible:
+	Usage: required
+	Value type: <string>
+	Definition: must be: "qcom,wcnss",
+
+- qcom,smd-channel:
+	Usage: required
+	Value type: <string>
+	Definition: standard SMD property specifying the SMD channel used for
+		    communication with the WiFi firmware.
+		    Should be "WCNSS_CTRL".
+
+- qcom,mmio:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: reference to a node specifying the wcnss "ccu" and "dxe"
+		    register blocks. The node must be compatible with one of
+		    the following:
+		    "qcom,riva",
+		    "qcom,pronto"
+
+= SUBNODES
+The subnodes of the wcnss node are optional and describe the individual blocks in
+the WCNSS.
+
+== Bluetooth
+The following properties are defined to the bluetooth node:
+
+- compatible:
+	Usage: required
+	Value type: <string>
+	Definition: must be:
+		    "qcom,wcnss-bt"
+
+== WiFi
+The following properties are defined to the WiFi node:
+
+- compatible:
+	Usage: required
+	Value type: <string>
+	Definition: must be one of:
+		    "qcom,wcnss-wlan",
+
+- interrupts:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: should specify the "rx" and "tx" interrupts
+
+- interrupt-names:
+	Usage: required
+	Value type: <stringlist>
+	Definition: must contain "rx" and "tx"
+
+- qcom,smem-state:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: should reference the tx-enable and tx-rings-empty SMEM states
+
+- qcom,smem-state-names:
+	Usage: required
+	Value type: <stringlist>
+	Definition: must contain "tx-enable" and "tx-rings-empty"
+
+= EXAMPLE
+The following example represents a SMD node, with one edge representing the
+"pronto" subsystem, with the wcnss device and its wcn3680 BT and WiFi blocks
+described; as found on the 8974 platform.
+
+smd {
+	compatible = "qcom,smd";
+
+	pronto-edge {
+		interrupts = <0 142 1>;
+
+		qcom,ipc = <&apcs 8 17>;
+		qcom,smd-edge = <6>;
+
+		wcnss {
+			compatible = "qcom,wcnss";
+			qcom,smd-channels = "WCNSS_CTRL";
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			qcom,mmio = <&pronto>;
+
+			bt {
+				compatible = "qcom,wcnss-bt";
+			};
+
+			wlan {
+				compatible = "qcom,wcnss-wlan";
+
+				interrupts = <0 145 0>, <0 146 0>;
+				interrupt-names = "tx", "rx";
+
+				qcom,smem-state = <&apps_smsm 10>, <&apps_smsm 9>;
+				qcom,smem-state-names = "tx-enable", "tx-rings-empty";
+			};
+		};
+	};
+};
+
+soc {
+	pronto: pronto {
+		compatible = "qcom,pronto";
+
+		reg = <0xfb204000 0x2000>, <0xfb202000 0x1000>, <0xfb21b000 0x3000>;
+		reg-names = "ccu", "dxe", "pmu";
+	};
+};