dts: update to v4.4-rc1

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

14 files changed, 437 insertions, 13 deletions

diff --git a/dts/Bindings/sound/ak4554.c b/dts/Bindings/sound/ak4554.txt
index 934fa02754..934fa02754 100644
--- a/dts/Bindings/sound/ak4554.c
+++ b/dts/Bindings/sound/ak4554.txt
diff --git a/dts/Bindings/sound/ak4613.txt b/dts/Bindings/sound/ak4613.txt
new file mode 100644
index 0000000000..15a919522b
--- /dev/null
+++ b/dts/Bindings/sound/ak4613.txt
@@ -0,0 +1,17 @@
+AK4613 I2C transmitter
+
+This device supports I2C mode only.
+
+Required properties:
+
+- compatible : "asahi-kasei,ak4613"
+- reg : The chip select number on the I2C bus
+
+Example:
+
+&i2c {
+	ak4613: ak4613@0x10 {
+		compatible = "asahi-kasei,ak4613";
+		reg = <0x10>;
+	};
+};
diff --git a/dts/Bindings/sound/ak4642.txt b/dts/Bindings/sound/ak4642.txt
index 623d4e70ae..340784db68 100644
--- a/dts/Bindings/sound/ak4642.txt
+++ b/dts/Bindings/sound/ak4642.txt
@@ -7,7 +7,14 @@ Required properties:
   - compatible : "asahi-kasei,ak4642" or "asahi-kasei,ak4643" or "asahi-kasei,ak4648"
   - reg : The chip select number on the I2C bus
 
-Example:
+Optional properties:
+
+  - #clock-cells :		common clock binding; shall be set to 0
+  - clocks :			common clock binding; MCKI clock
+  - clock-frequency :		common clock binding; frequency of MCKO
+  - clock-output-names :	common clock binding; MCKO clock name
+
+Example 1:
 
 &i2c {
 	ak4648: ak4648@0x12 {
@@ -15,3 +22,16 @@ Example:
 		reg = <0x12>;
 	};
 };
+
+Example 2:
+
+&i2c {
+	ak4643: codec@12 {
+		compatible = "asahi-kasei,ak4643";
+		reg = <0x12>;
+		#clock-cells = <0>;
+		clocks = <&audio_clock>;
+		clock-frequency = <12288000>;
+		clock-output-names = "ak4643_mcko";
+	};
+};
diff --git a/dts/Bindings/sound/atmel-classd.txt b/dts/Bindings/sound/atmel-classd.txt
new file mode 100644
index 0000000000..0018451c43
--- /dev/null
+++ b/dts/Bindings/sound/atmel-classd.txt
@@ -0,0 +1,52 @@
+* Atmel ClassD driver under ALSA SoC architecture
+
+Required properties:
+- compatible
+	Should be "atmel,sama5d2-classd".
+- reg
+	Should contain ClassD registers location and length.
+- interrupts
+	Should contain the IRQ line for the ClassD.
+- dmas
+	One DMA specifiers as described in atmel-dma.txt and dma.txt files.
+- dma-names
+	Must be "tx".
+- clock-names
+	Tuple listing input clock names.
+	Required elements: "pclk", "gclk" and "aclk".
+- clocks
+	Please refer to clock-bindings.txt.
+
+Optional properties:
+- pinctrl-names, pinctrl-0
+	Please refer to pinctrl-bindings.txt.
+- atmel,model
+	The user-visible name of this sound complex.
+	The default value is "CLASSD".
+- atmel,pwm-type
+	PWM modulation type, "single" or "diff".
+	The default value is "single".
+- atmel,non-overlap-time
+	Set non-overlapping time, the unit is nanosecond(ns).
+	There are four values,
+	<5>, <10>, <15>, <20>, the default value is <10>.
+	Non-overlapping will be disabled if not specified.
+
+Example:
+classd: classd@fc048000 {
+		compatible = "atmel,sama5d2-classd";
+		reg = <0xfc048000 0x100>;
+		interrupts = <59 IRQ_TYPE_LEVEL_HIGH 7>;
+		dmas = <&dma0
+			(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
+			| AT91_XDMAC_DT_PERID(47))>;
+		dma-names = "tx";
+		clocks = <&classd_clk>, <&classd_gclk>, <&audio_pll_pmc>;
+		clock-names = "pclk", "gclk", "aclk";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_classd_default>;
+		atmel,model = "classd @ SAMA5D2-Xplained";
+		atmel,pwm-type = "diff";
+		atmel,non-overlap-time = <10>;
+};
diff --git a/dts/Bindings/sound/da7213.txt b/dts/Bindings/sound/da7213.txt
new file mode 100644
index 0000000000..58902802d5
--- /dev/null
+++ b/dts/Bindings/sound/da7213.txt
@@ -0,0 +1,41 @@
+Dialog Semiconductor DA7213 Audio Codec bindings
+
+======
+
+Required properties:
+- compatible : Should be "dlg,da7213"
+- reg: Specifies the I2C slave address
+
+Optional properties:
+- clocks : phandle and clock specifier for codec MCLK.
+- clock-names : Clock name string for 'clocks' attribute, should be "mclk".
+
+- dlg,micbias1-lvl : Voltage (mV) for Mic Bias 1
+	[<1600>, <2200>, <2500>, <3000>]
+- dlg,micbias2-lvl : Voltage (mV) for Mic Bias 2
+	[<1600>, <2200>, <2500>, <3000>]
+- dlg,dmic-data-sel : DMIC channel select based on clock edge.
+	["lrise_rfall", "lfall_rrise"]
+- dlg,dmic-samplephase : When to sample audio from DMIC.
+	["on_clkedge", "between_clkedge"]
+- dlg,dmic-clkrate : DMIC clock frequency (Hz).
+	[<1500000>, <3000000>]
+
+======
+
+Example:
+
+	codec_i2c: da7213@1a {
+		compatible = "dlg,da7213";
+ 		reg = <0x1a>;
+
+ 		clocks = <&clks 201>;
+		clock-names = "mclk";
+
+		dlg,micbias1-lvl = <2500>;
+		dlg,micbias2-lvl = <2500>;
+
+		dlg,dmic-data-sel = "lrise_rfall";
+		dlg,dmic-samplephase = "between_clkedge";
+		dlg,dmic-clkrate = <3000000>;
+	};
diff --git a/dts/Bindings/sound/da7219.txt b/dts/Bindings/sound/da7219.txt
new file mode 100644
index 0000000000..1b7030911a
--- /dev/null
+++ b/dts/Bindings/sound/da7219.txt
@@ -0,0 +1,106 @@
+Dialog Semiconductor DA7219 Audio Codec bindings
+
+DA7219 is an audio codec with advanced accessory detect features.
+
+======
+
+Required properties:
+- compatible : Should be "dlg,da7219"
+- reg: Specifies the I2C slave address
+
+- interrupt-parent : Specifies the phandle of the interrupt controller to which
+  the IRQs from DA7219 are delivered to.
+- interrupts : IRQ line info for DA7219.
+  (See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt for
+   further information relating to interrupt properties)
+
+- VDD-supply: VDD power supply for the device
+- VDDMIC-supply: VDDMIC power supply for the device
+- VDDIO-supply: VDDIO power supply for the device
+  (See Documentation/devicetree/bindings/regulator/regulator.txt for further
+   information relating to regulators)
+
+Optional properties:
+- interrupt-names : Name associated with interrupt line. Should be "wakeup" if
+  interrupt is to be used to wake system, otherwise "irq" should be used.
+- wakeup-source: Flag to indicate this device can wake system (suspend/resume).
+
+- clocks : phandle and clock specifier for codec MCLK.
+- clock-names : Clock name string for 'clocks' attribute, should be "mclk".
+
+- dlg,ldo-lvl : Required internal LDO voltage (mV) level for digital engine
+	[<1050>, <1100>, <1200>, <1400>]
+- dlg,micbias-lvl : Voltage (mV) for Mic Bias
+	[<1800>, <2000>, <2200>, <2400>, <2600>]
+- dlg,mic-amp-in-sel : Mic input source type
+	["diff", "se_p", "se_n"]
+
+======
+
+Child node - 'da7219_aad':
+
+Optional properties:
+- dlg,micbias-pulse-lvl : Mic bias higher voltage pulse level (mV).
+	[<2800>, <2900>]
+- dlg,micbias-pulse-time : Mic bias higher voltage pulse duration (ms)
+- dlg,btn-cfg : Periodic button press measurements for 4-pole jack (ms)
+	[<2>, <5>, <10>, <50>, <100>, <200>, <500>]
+- dlg,mic-det-thr : Impedance threshold for mic detection measurement (Ohms)
+	[<200>, <500>, <750>, <1000>]
+- dlg,jack-ins-deb : Debounce time for jack insertion (ms)
+	[<5>, <10>, <20>, <50>, <100>, <200>, <500>, <1000>]
+- dlg,jack-det-rate: Jack type detection latency (3/4 pole)
+	["32ms_64ms", "64ms_128ms", "128ms_256ms", "256ms_512ms"]
+- dlg,jack-rem-deb : Debounce time for jack removal (ms)
+	[<1>, <5>, <10>, <20>]
+- dlg,a-d-btn-thr : Impedance threshold between buttons A and D
+	[0x0 - 0xFF]
+- dlg,d-b-btn-thr : Impedance threshold between buttons D and B
+	[0x0 - 0xFF]
+- dlg,b-c-btn-thr : Impedance threshold between buttons B and C
+	[0x0 - 0xFF]
+- dlg,c-mic-btn-thr : Impedance threshold between button C and Mic
+	[0x0 - 0xFF]
+- dlg,btn-avg : Number of 8-bit readings for averaged button measurement
+	[<1>, <2>, <4>, <8>]
+- dlg,adc-1bit-rpt : Repeat count for 1-bit button measurement
+	[<1>, <2>, <4>, <8>]
+
+======
+
+Example:
+
+	codec: da7219@1a {
+		compatible = "dlg,da7219";
+		reg = <0x1a>;
+
+		interrupt-parent = <&gpio6>;
+		interrupts = <11 IRQ_TYPE_LEVEL_HIGH>;
+
+		VDD-supply = <&reg_audio>;
+		VDDMIC-supply = <&reg_audio>;
+		VDDIO-supply = <&reg_audio>;
+
+		clocks = <&clks 201>;
+		clock-names = "mclk";
+
+		dlg,ldo-lvl = <1200>;
+		dlg,micbias-lvl = <2600>;
+		dlg,mic-amp-in-sel = "diff";
+
+		da7219_aad {
+			dlg,btn-cfg = <50>;
+			dlg,mic-det-thr = <500>;
+			dlg,jack-ins-deb = <20>;
+			dlg,jack-det-rate = "32ms_64ms";
+			dlg,jack-rem-deb = <1>;
+
+			dlg,a-d-btn-thr = <0xa>;
+			dlg,d-b-btn-thr = <0x16>;
+			dlg,b-c-btn-thr = <0x21>;
+			dlg,c-mic-btn-thr = <0x3E>;
+
+			dlg,btn-avg = <4>;
+			dlg,adc-1bit-rpt = <1>;
+		};
+	};
diff --git a/dts/Bindings/sound/fsl-asoc-card.txt b/dts/Bindings/sound/fsl-asoc-card.txt
index a96774c194..ce55c0a6f7 100644
--- a/dts/Bindings/sound/fsl-asoc-card.txt
+++ b/dts/Bindings/sound/fsl-asoc-card.txt
@@ -13,13 +13,15 @@ So having this generic sound card allows all Freescale SoC users to benefit
 from the simplification of a new card support and the capability of the wide
 sample rates support through ASRC.
 
-Note: The card is initially designed for those sound cards who use I2S and
-      PCM DAI formats. However, it'll be also possible to support those non
-      I2S/PCM type sound cards, such as S/PDIF audio and HDMI audio, as long
-      as the driver has been properly upgraded.
+Note: The card is initially designed for those sound cards who use AC'97, I2S
+      and PCM DAI formats. However, it'll be also possible to support those non
+      AC'97/I2S/PCM type sound cards, such as S/PDIF audio and HDMI audio, as
+      long as the driver has been properly upgraded.
 
 
 The compatible list for this generic sound card currently:
+ "fsl,imx-audio-ac97"
+
  "fsl,imx-audio-cs42888"
 
  "fsl,imx-audio-wm8962"
diff --git a/dts/Bindings/sound/nau8825.txt b/dts/Bindings/sound/nau8825.txt
new file mode 100644
index 0000000000..d3374231c8
--- /dev/null
+++ b/dts/Bindings/sound/nau8825.txt
@@ -0,0 +1,102 @@
+Nuvoton NAU8825 audio codec
+
+This device supports I2C only.
+
+Required properties:
+  - compatible : Must be "nuvoton,nau8825"
+
+  - reg : the I2C address of the device. This is either 0x1a (CSB=0) or 0x1b (CSB=1).
+
+Optional properties:
+  - nuvoton,jkdet-enable: Enable jack detection via JKDET pin.
+  - nuvoton,jkdet-pull-enable: Enable JKDET pin pull. If set - pin pull enabled,
+      otherwise pin in high impedance state.
+  - nuvoton,jkdet-pull-up: Pull-up JKDET pin. If set then JKDET pin is pull up, otherwise pull down.
+  - nuvoton,jkdet-polarity: JKDET pin polarity. 0 - active high, 1 - active low.
+
+  - nuvoton,vref-impedance: VREF Impedance selection
+      0 - Open
+      1 - 25 kOhm
+      2 - 125 kOhm
+      3 - 2.5 kOhm
+
+  - nuvoton,micbias-voltage: Micbias voltage level.
+      0 - VDDA
+      1 - VDDA
+      2 - VDDA * 1.1
+      3 - VDDA * 1.2
+      4 - VDDA * 1.3
+      5 - VDDA * 1.4
+      6 - VDDA * 1.53
+      7 - VDDA * 1.53
+
+  - nuvoton,sar-threshold-num: Number of buttons supported
+  - nuvoton,sar-threshold: Impedance threshold for each button. Array that contains up to 8 buttons configuration. SAR value is calculated as
+    SAR = 255 * MICBIAS / SAR_VOLTAGE * R / (2000 + R)
+    where MICBIAS is configured by 'nuvoton,micbias-voltage', SAR_VOLTAGE is configured by 'nuvoton,sar-voltage', R - button impedance.
+    Refer datasheet section 10.2 for more information about threshold calculation.
+
+  - nuvoton,sar-hysteresis: Button impedance measurement hysteresis.
+
+  - nuvoton,sar-voltage: Reference voltage for button impedance measurement.
+      0 - VDDA
+      1 - VDDA
+      2 - VDDA * 1.1
+      3 - VDDA * 1.2
+      4 - VDDA * 1.3
+      5 - VDDA * 1.4
+      6 - VDDA * 1.53
+      7 - VDDA * 1.53
+
+  - nuvoton,sar-compare-time: SAR compare time
+      0 - 500 ns
+      1 - 1 us
+      2 - 2 us
+      3 - 4 us
+
+  - nuvoton,sar-sampling-time: SAR sampling time
+      0 - 2 us
+      1 - 4 us
+      2 - 8 us
+      3 - 16 us
+
+  - nuvoton,short-key-debounce: Button short key press debounce time.
+      0 - 30 ms
+      1 - 50 ms
+      2 - 100 ms
+      3 - 30 ms
+
+  - nuvoton,jack-insert-debounce: number from 0 to 7 that sets debounce time to 2^(n+2) ms
+  - nuvoton,jack-eject-debounce: number from 0 to 7 that sets debounce time to 2^(n+2) ms
+
+  - clocks: list of phandle and clock specifier pairs according to common clock bindings for the
+      clocks described in clock-names
+  - clock-names: should include "mclk" for the MCLK master clock
+
+Example:
+
+  headset: nau8825@1a {
+      compatible = "nuvoton,nau8825";
+      reg = <0x1a>;
+      interrupt-parent = <&gpio>;
+      interrupts = <TEGRA_GPIO(E, 6) IRQ_TYPE_LEVEL_LOW>;
+      nuvoton,jkdet-enable;
+      nuvoton,jkdet-pull-enable;
+      nuvoton,jkdet-pull-up;
+      nuvoton,jkdet-polarity = <GPIO_ACTIVE_LOW>;
+      nuvoton,vref-impedance = <2>;
+      nuvoton,micbias-voltage = <6>;
+      // Setup 4 buttons impedance according to Android specification
+      nuvoton,sar-threshold-num = <4>;
+      nuvoton,sar-threshold = <0xc 0x1e 0x38 0x60>;
+      nuvoton,sar-hysteresis = <1>;
+      nuvoton,sar-voltage = <0>;
+      nuvoton,sar-compare-time = <0>;
+      nuvoton,sar-sampling-time = <0>;
+      nuvoton,short-key-debounce = <2>;
+      nuvoton,jack-insert-debounce = <7>;
+      nuvoton,jack-eject-debounce = <7>;
+
+      clock-names = "mclk";
+      clocks = <&tegra_car TEGRA210_CLK_CLK_OUT_2>;
+  };
diff --git a/dts/Bindings/sound/renesas,rsnd.txt b/dts/Bindings/sound/renesas,rsnd.txt
index 1173395b5e..c57cbd6573 100644
--- a/dts/Bindings/sound/renesas,rsnd.txt
+++ b/dts/Bindings/sound/renesas,rsnd.txt
@@ -4,10 +4,12 @@ Required properties:
 - compatible			: "renesas,rcar_sound-<soctype>", fallbacks
 				  "renesas,rcar_sound-gen1" if generation1, and
 				  "renesas,rcar_sound-gen2" if generation2
+				  "renesas,rcar_sound-gen3" if generation3
 				  Examples with soctypes are:
 				    - "renesas,rcar_sound-r8a7778" (R-Car M1A)
 				    - "renesas,rcar_sound-r8a7790" (R-Car H2)
 				    - "renesas,rcar_sound-r8a7791" (R-Car M2-W)
+				    - "renesas,rcar_sound-r8a7795" (R-Car H3)
 - reg				: Should contain the register physical address.
 				  required register is
 				   SRU/ADG/SSI      if generation1
@@ -30,6 +32,11 @@ Required properties:
 - rcar_sound,dai		: DAI contents.
 				  The number of DAI subnode should be same as HW.
 				  see below for detail.
+- #sound-dai-cells		: it must be 0 if your system is using single DAI
+				  it must be 1 if your system is using multi  DAI
+- #clock-cells			: it must be 0 if your system has audio_clkout
+				  it must be 1 if your system has audio_clkout0/1/2/3
+- clock-frequency		: for all audio_clkout0/1/2/3
 
 SSI subnode properties:
 - interrupts			: Should contain SSI interrupt for PIO transfer
diff --git a/dts/Bindings/sound/rockchip-i2s.txt b/dts/Bindings/sound/rockchip-i2s.txt
index 9b82c20b30..2267d249ca 100644
--- a/dts/Bindings/sound/rockchip-i2s.txt
+++ b/dts/Bindings/sound/rockchip-i2s.txt
@@ -12,8 +12,6 @@ Required properties:
 - reg: physical base address of the controller and length of memory mapped
   region.
 - interrupts: should contain the I2S interrupt.
-- #address-cells: should be 1.
-- #size-cells: should be 0.
 - dmas: DMA specifiers for tx and rx dma. See the DMA client binding,
 	Documentation/devicetree/bindings/dma/dma.txt
 - dma-names: should include "tx" and "rx".
@@ -21,6 +19,7 @@ Required properties:
 - clock-names: should contain followings:
    - "i2s_hclk": clock for I2S BUS
    - "i2s_clk" : clock for I2S controller
+- rockchip,capture-channels: max capture channels, if not set, 2 channels default.
 
 Example for rk3288 I2S controller:
 
@@ -28,10 +27,9 @@ i2s@ff890000 {
 	compatible = "rockchip,rk3288-i2s", "rockchip,rk3066-i2s";
 	reg = <0xff890000 0x10000>;
 	interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
-	#address-cells = <1>;
-	#size-cells = <0>;
 	dmas = <&pdma1 0>, <&pdma1 1>;
 	dma-names = "tx", "rx";
 	clock-names = "i2s_hclk", "i2s_clk";
 	clocks = <&cru HCLK_I2S0>, <&cru SCLK_I2S0>;
+	rockchip,capture-channels = <2>;
 };
diff --git a/dts/Bindings/sound/rockchip-spdif.txt b/dts/Bindings/sound/rockchip-spdif.txt
new file mode 100644
index 0000000000..e64dbdea7d
--- /dev/null
+++ b/dts/Bindings/sound/rockchip-spdif.txt
@@ -0,0 +1,40 @@
+* Rockchip SPDIF transceiver
+
+The S/PDIF audio block is a stereo transceiver that allows the
+processor to receive and transmit digital audio via an coaxial cable or
+a fibre cable.
+
+Required properties:
+
+- compatible: should be one of the following:
+   - "rockchip,rk3288-spdif", "rockchip,rk3188-spdif" or
+     "rockchip,rk3066-spdif"
+- reg: physical base address of the controller and length of memory mapped
+  region.
+- interrupts: should contain the SPDIF interrupt.
+- dmas: DMA specifiers for tx dma. See the DMA client binding,
+  Documentation/devicetree/bindings/dma/dma.txt
+- dma-names: should be "tx"
+- clocks: a list of phandle + clock-specifier pairs, one for each entry
+  in clock-names.
+- clock-names: should contain following:
+   - "hclk": clock for SPDIF controller
+   - "mclk" : clock for SPDIF bus
+
+Required properties on RK3288:
+  - rockchip,grf: the phandle of the syscon node for the general register
+                   file (GRF)
+
+Example for the rk3188 SPDIF controller:
+
+spdif: spdif@0x1011e000 {
+	compatible = "rockchip,rk3188-spdif", "rockchip,rk3066-spdif";
+	reg = <0x1011e000 0x2000>;
+	interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+	dmas = <&dmac1_s 8>;
+	dma-names = "tx";
+	clock-names = "hclk", "mclk";
+	clocks = <&cru HCLK_SPDIF>, <&cru SCLK_SPDIF>;
+	status = "disabled";
+	#sound-dai-cells = <0>;
+};
diff --git a/dts/Bindings/sound/rt5640.txt b/dts/Bindings/sound/rt5640.txt
index bac4d9ac1e..9e62f6eb34 100644
--- a/dts/Bindings/sound/rt5640.txt
+++ b/dts/Bindings/sound/rt5640.txt
@@ -14,7 +14,8 @@ Optional properties:
 
 - realtek,in1-differential
 - realtek,in2-differential
-  Boolean. Indicate MIC1/2 input are differential, rather than single-ended.
+- realtek,in3-differential
+  Boolean. Indicate MIC1/2/3 input are differential, rather than single-ended.
 
 - realtek,ldo1-en-gpios : The GPIO that controls the CODEC's LDO1_EN pin.
 
@@ -24,9 +25,11 @@ Pins on the device (for linking into audio routes) for RT5639/RT5640:
   * DMIC2
   * MICBIAS1
   * IN1P
-  * IN1R
+  * IN1N
   * IN2P
-  * IN2R
+  * IN2N
+  * IN3P
+  * IN3N
   * HPOL
   * HPOR
   * LOUTL
diff --git a/dts/Bindings/sound/sun4i-codec.txt b/dts/Bindings/sound/sun4i-codec.txt
new file mode 100644
index 0000000000..c92966bd54
--- /dev/null
+++ b/dts/Bindings/sound/sun4i-codec.txt
@@ -0,0 +1,27 @@
+* Allwinner A10 Codec
+
+Required properties:
+- compatible: must be either "allwinner,sun4i-a10-codec" or
+  "allwinner,sun7i-a20-codec"
+- reg: must contain the registers location and length
+- interrupts: must contain the codec interrupt
+- dmas: DMA channels for tx and rx dma. See the DMA client binding,
+	Documentation/devicetree/bindings/dma/dma.txt
+- dma-names: should include "tx" and "rx".
+- clocks: a list of phandle + clock-specifer pairs, one for each entry
+  in clock-names.
+- clock-names: should contain followings:
+   - "apb": the parent APB clock for this controller
+   - "codec": the parent module clock
+
+Example:
+codec: codec@01c22c00 {
+	#sound-dai-cells = <0>;
+	compatible = "allwinner,sun7i-a20-codec";
+	reg = <0x01c22c00 0x40>;
+	interrupts = <0 30 4>;
+	clocks = <&apb0_gates 0>, <&codec_clk>;
+	clock-names = "apb", "codec";
+	dmas = <&dma 0 19>, <&dma 0 19>;
+	dma-names = "rx", "tx";
+};
diff --git a/dts/Bindings/sound/tdm-slot.txt b/dts/Bindings/sound/tdm-slot.txt
index 6a2c84247f..34cf70e2cb 100644
--- a/dts/Bindings/sound/tdm-slot.txt
+++ b/dts/Bindings/sound/tdm-slot.txt
@@ -4,11 +4,15 @@ This specifies audio DAI's TDM slot.
 
 TDM slot properties:
 dai-tdm-slot-num : Number of slots in use.
-dai-tdm-slot-width :  Width in bits for each slot.
+dai-tdm-slot-width : Width in bits for each slot.
+dai-tdm-slot-tx-mask : Transmit direction slot mask, optional
+dai-tdm-slot-rx-mask : Receive direction slot mask, optional
 
 For instance:
 	dai-tdm-slot-num = <2>;
 	dai-tdm-slot-width = <8>;
+	dai-tdm-slot-tx-mask = <0 1>;
+	dai-tdm-slot-rx-mask = <1 0>;
 
 And for each spcified driver, there could be one .of_xlate_tdm_slot_mask()
 to specify a explicit mapping of the channels and the slots. If it's absent
@@ -18,3 +22,8 @@ tx and rx masks.
 For snd_soc_of_xlate_tdm_slot_mask(), the tx and rx masks will use a 1 bit
 for an active slot as default, and the default active bits are at the LSB of
 the masks.
+
+The explicit masks are given as array of integers, where the first
+number presents bit-0 (LSB), second presents bit-1, etc. Any non zero
+number is considered 1 and 0 is 0. snd_soc_of_xlate_tdm_slot_mask()
+does not do anything, if either mask is set non zero value.