dts: update to v4.18-rc1

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

49 files changed, 668 insertions, 36 deletions

diff --git a/dts/Bindings/sound/adi,ssm2305.txt b/dts/Bindings/sound/adi,ssm2305.txt
new file mode 100644
index 0000000000..a9c9d83c8a
--- /dev/null
+++ b/dts/Bindings/sound/adi,ssm2305.txt
@@ -0,0 +1,14 @@
+Analog Devices SSM2305 Speaker Amplifier
+========================================
+
+Required properties:
+  - compatible : "adi,ssm2305"
+  - shutdown-gpios : The gpio connected to the shutdown pin.
+                     The gpio signal is ACTIVE_LOW.
+
+Example:
+
+ssm2305: analog-amplifier {
+	compatible = "adi,ssm2305";
+	shutdown-gpios = <&gpio3 20 GPIO_ACTIVE_LOW>;
+};
diff --git a/dts/Bindings/sound/atmel-i2s.txt b/dts/Bindings/sound/atmel-i2s.txt
new file mode 100644
index 0000000000..735368b8a7
--- /dev/null
+++ b/dts/Bindings/sound/atmel-i2s.txt
@@ -0,0 +1,47 @@
+* Atmel I2S controller
+
+Required properties:
+- compatible:     Should be "atmel,sama5d2-i2s".
+- reg:            Should be the physical base address of the controller and the
+                  length of memory mapped region.
+- interrupts:     Should contain the interrupt for the controller.
+- dmas:           Should be one per channel name listed in the dma-names property,
+                  as described in atmel-dma.txt and dma.txt files.
+- dma-names:      Two dmas have to be defined, "tx" and "rx".
+                  This IP also supports one shared channel for both rx and tx;
+                  if this mode is used, one "rx-tx" name must be used.
+- clocks:         Must contain an entry for each entry in clock-names.
+                  Please refer to clock-bindings.txt.
+- clock-names:    Should be one of each entry matching the clocks phandles list:
+                  - "pclk" (peripheral clock) Required.
+                  - "gclk" (generated clock) Optional (1).
+                  - "aclk" (Audio PLL clock) Optional (1).
+                  - "muxclk" (I2S mux clock) Optional (1).
+
+Optional properties:
+- pinctrl-0:      Should specify pin control groups used for this controller.
+- princtrl-names: Should contain only one value - "default".
+
+
+(1) : Only the peripheral clock is required. The generated clock, the Audio
+      PLL clock adn the I2S mux clock are optional and should only be set
+      together, when Master Mode is required.
+
+Example:
+
+	i2s@f8050000 {
+		compatible = "atmel,sama5d2-i2s";
+		reg = <0xf8050000 0x300>;
+		interrupts = <54 IRQ_TYPE_LEVEL_HIGH 7>;
+		dmas = <&dma0
+			(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+			 AT91_XDMAC_DT_PERID(31))>,
+		       <&dma0
+			(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+			 AT91_XDMAC_DT_PERID(32))>;
+		dma-names = "tx", "rx";
+		clocks = <&i2s0_clk>, <&i2s0_gclk>, <&audio_pll_pmc>, <&i2s0muxck>;
+		clock-names = "pclk", "gclk", "aclk", "muxclk";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_i2s0_default>;
+	};
diff --git a/dts/Bindings/sound/cs42xx8.txt b/dts/Bindings/sound/cs42xx8.txt
index f631fbca62..8619a156d0 100644
--- a/dts/Bindings/sound/cs42xx8.txt
+++ b/dts/Bindings/sound/cs42xx8.txt
@@ -16,7 +16,7 @@ Required properties:
 
 Example:
 
-codec: cs42888@48 {
+cs42888: codec@48 {
 	compatible = "cirrus,cs42888";
 	reg = <0x48>;
 	clocks = <&codec_mclk 0>;
diff --git a/dts/Bindings/sound/fsl,asrc.txt b/dts/Bindings/sound/fsl,asrc.txt
index f5a14115b4..1d4d9f9386 100644
--- a/dts/Bindings/sound/fsl,asrc.txt
+++ b/dts/Bindings/sound/fsl,asrc.txt
@@ -31,14 +31,16 @@ Required properties:
 			  it. This property is optional depending on the SoC
 			  design.
 
-   - big-endian		: If this property is absent, the little endian mode
-			  will be in use as default. Otherwise, the big endian
-			  mode will be in use for all the device registers.
-
    - fsl,asrc-rate	: Defines a mutual sample rate used by DPCM Back Ends.
 
    - fsl,asrc-width	: Defines a mutual sample width used by DPCM Back Ends.
 
+Optional properties:
+
+   - big-endian		: If this property is absent, the little endian mode
+			  will be in use as default. Otherwise, the big endian
+			  mode will be in use for all the device registers.
+
 Example:
 
 asrc: asrc@2034000 {
diff --git a/dts/Bindings/sound/fsl,esai.txt b/dts/Bindings/sound/fsl,esai.txt
index cacd18bb9b..5b99143676 100644
--- a/dts/Bindings/sound/fsl,esai.txt
+++ b/dts/Bindings/sound/fsl,esai.txt
@@ -42,6 +42,8 @@ Required properties:
 			  means all the settings for Receiving would be
 			  duplicated from Transmition related registers.
 
+Optional properties:
+
   - big-endian		: If this property is absent, the native endian mode
 			  will be in use as default, or the big endian mode
 			  will be in use for all the device registers.
diff --git a/dts/Bindings/sound/fsl,spdif.txt b/dts/Bindings/sound/fsl,spdif.txt
index 38cfa75734..8b324f82a7 100644
--- a/dts/Bindings/sound/fsl,spdif.txt
+++ b/dts/Bindings/sound/fsl,spdif.txt
@@ -33,6 +33,8 @@ Required properties:
 			  it. This property is optional depending on the SoC
 			  design.
 
+Optional properties:
+
    - big-endian		: If this property is absent, the native endian mode
 			  will be in use as default, or the big endian mode
 			  will be in use for all the device registers.
diff --git a/dts/Bindings/sound/fsl-sai.txt b/dts/Bindings/sound/fsl-sai.txt
index 740b467adf..dd9e59738e 100644
--- a/dts/Bindings/sound/fsl-sai.txt
+++ b/dts/Bindings/sound/fsl-sai.txt
@@ -28,9 +28,6 @@ Required properties:
 			  pinctrl-names. See ../pinctrl/pinctrl-bindings.txt
 			  for details of the property values.
 
-  - big-endian		: Boolean property, required if all the FTM_PWM
-			  registers are big-endian rather than little-endian.
-
   - lsb-first		: Configures whether the LSB or the MSB is transmitted
 			  first for the fifo data. If this property is absent,
 			  the MSB is transmitted first as default, or the LSB
@@ -48,6 +45,11 @@ Required properties:
 			  receive data by following their own bit clocks and
 			  frame sync clocks separately.
 
+Optional properties:
+
+  - big-endian		: Boolean property, required if all the SAI
+			  registers are big-endian rather than little-endian.
+
 Optional properties (for mx6ul):
 
   - fsl,sai-mclk-direction-output: This is a boolean property. If present,
diff --git a/dts/Bindings/sound/mt2701-afe-pcm.txt b/dts/Bindings/sound/mt2701-afe-pcm.txt
index e2f7f49512..560762e0a1 100644
--- a/dts/Bindings/sound/mt2701-afe-pcm.txt
+++ b/dts/Bindings/sound/mt2701-afe-pcm.txt
@@ -1,7 +1,9 @@
 Mediatek AFE PCM controller for mt2701
 
 Required properties:
-- compatible = "mediatek,mt2701-audio";
+- compatible: should be one of the followings.
+	      - "mediatek,mt2701-audio"
+	      - "mediatek,mt7622-audio"
 - interrupts: should contain AFE and ASYS interrupts
 - interrupt-names: should be "afe" and "asys"
 - power-domains: should define the power domain
diff --git a/dts/Bindings/sound/mt6351.txt b/dts/Bindings/sound/mt6351.txt
new file mode 100644
index 0000000000..7fb2cb9924
--- /dev/null
+++ b/dts/Bindings/sound/mt6351.txt
@@ -0,0 +1,16 @@
+Mediatek MT6351 Audio Codec
+
+The communication between MT6351 and SoC is through Mediatek PMIC wrapper.
+For more detail, please visit Mediatek PMIC wrapper documentation.
+
+Must be a child node of PMIC wrapper.
+
+Required properties:
+
+- compatible : "mediatek,mt6351-sound".
+
+Example:
+
+mt6351_snd {
+	compatible = "mediatek,mt6351-sound";
+};
diff --git a/dts/Bindings/sound/mt6797-afe-pcm.txt b/dts/Bindings/sound/mt6797-afe-pcm.txt
new file mode 100644
index 0000000000..0ae29de15b
--- /dev/null
+++ b/dts/Bindings/sound/mt6797-afe-pcm.txt
@@ -0,0 +1,42 @@
+Mediatek AFE PCM controller for mt6797
+
+Required properties:
+- compatible = "mediatek,mt6797-audio";
+- reg: register location and size
+- interrupts: should contain AFE interrupt
+- power-domains: should define the power domain
+- clocks: Must contain an entry for each entry in clock-names
+- clock-names: should have these clock names:
+		"infra_sys_audio_clk",
+		"infra_sys_audio_26m",
+		"mtkaif_26m_clk",
+		"top_mux_audio",
+		"top_mux_aud_intbus",
+		"top_sys_pll3_d4",
+		"top_sys_pll1_d4",
+		"top_clk26m_clk";
+
+Example:
+
+	afe: mt6797-afe-pcm@11220000  {
+		compatible = "mediatek,mt6797-audio";
+		reg = <0 0x11220000 0 0x1000>;
+		interrupts = <GIC_SPI 151 IRQ_TYPE_LEVEL_LOW>;
+		power-domains = <&scpsys MT6797_POWER_DOMAIN_AUDIO>;
+		clocks = <&infrasys CLK_INFRA_AUDIO>,
+			 <&infrasys CLK_INFRA_AUDIO_26M>,
+			 <&infrasys CLK_INFRA_AUDIO_26M_PAD_TOP>,
+			 <&topckgen CLK_TOP_MUX_AUDIO>,
+			 <&topckgen CLK_TOP_MUX_AUD_INTBUS>,
+			 <&topckgen CLK_TOP_SYSPLL3_D4>,
+			 <&topckgen CLK_TOP_SYSPLL1_D4>,
+			 <&clk26m>;
+		clock-names = "infra_sys_audio_clk",
+			      "infra_sys_audio_26m",
+			      "mtkaif_26m_clk",
+			      "top_mux_audio",
+			      "top_mux_aud_intbus",
+			      "top_sys_pll3_d4",
+			      "top_sys_pll1_d4",
+			      "top_clk26m_clk";
+	};
diff --git a/dts/Bindings/sound/mt6797-mt6351.txt b/dts/Bindings/sound/mt6797-mt6351.txt
new file mode 100644
index 0000000000..1d95a8840f
--- /dev/null
+++ b/dts/Bindings/sound/mt6797-mt6351.txt
@@ -0,0 +1,14 @@
+MT6797 with MT6351 CODEC
+
+Required properties:
+- compatible: "mediatek,mt6797-mt6351-sound"
+- mediatek,platform: the phandle of MT6797 ASoC platform
+- mediatek,audio-codec: the phandles of MT6351 codec
+
+Example:
+
+	sound {
+		compatible = "mediatek,mt6797-mt6351-sound";
+		mediatek,audio-codec = <&mt6351_snd>;
+		mediatek,platform = <&afe>;
+	};
diff --git a/dts/Bindings/sound/qcom,apq8096.txt b/dts/Bindings/sound/qcom,apq8096.txt
new file mode 100644
index 0000000000..aa54e49fc8
--- /dev/null
+++ b/dts/Bindings/sound/qcom,apq8096.txt
@@ -0,0 +1,109 @@
+* Qualcomm Technologies APQ8096 ASoC sound card driver
+
+This binding describes the APQ8096 sound card, which uses qdsp for audio.
+
+- compatible:
+	Usage: required
+	Value type: <stringlist>
+	Definition: must be "qcom,apq8096-sndcard"
+
+- qcom,audio-routing:
+	Usage: Optional
+	Value type: <stringlist>
+	Definition:  A list of the connections between audio components.
+		  Each entry is a pair of strings, the first being the
+		  connection's sink, the second being the connection's
+		  source. Valid names could be power supplies, MicBias
+		  of codec and the jacks on the board:
+		  Valid names include:
+
+		Board Connectors:
+			"Headphone Left"
+			"Headphone Right"
+			"Earphone"
+			"Line Out1"
+			"Line Out2"
+			"Line Out3"
+			"Line Out4"
+			"Analog Mic1"
+			"Analog Mic2"
+			"Analog Mic3"
+			"Analog Mic4"
+			"Analog Mic5"
+			"Analog Mic6"
+			"Digital Mic2"
+			"Digital Mic3"
+
+		Audio pins and MicBias on WCD9335 Codec:
+			"MIC_BIAS1
+			"MIC_BIAS2"
+			"MIC_BIAS3"
+			"MIC_BIAS4"
+			"AMIC1"
+			"AMIC2"
+			"AMIC3"
+			"AMIC4"
+			"AMIC5"
+			"AMIC6"
+			"AMIC6"
+			"DMIC1"
+			"DMIC2"
+			"DMIC3"
+= dailinks
+Each subnode of sndcard represents either a dailink, and subnodes of each
+dailinks would be cpu/codec/platform dais.
+
+- link-name:
+	Usage: required
+	Value type: <string>
+	Definition: User friendly name for dai link
+
+= CPU, PLATFORM, CODEC dais subnodes
+- cpu:
+	Usage: required
+	Value type: <subnode>
+	Definition: cpu dai sub-node
+
+- codec:
+	Usage: Optional
+	Value type: <subnode>
+	Definition: codec dai sub-node
+
+- platform:
+	Usage: Optional
+	Value type: <subnode>
+	Definition: platform dai sub-node
+
+- sound-dai:
+	Usage: required
+	Value type: <phandle with arguments>
+	Definition: dai phandle/s and port of CPU/CODEC/PLATFORM node.
+
+Example:
+
+audio {
+	compatible = "qcom,apq8096-sndcard";
+	qcom,model = "DB820c";
+
+	mm1-dai-link {
+		link-name = "MultiMedia1";
+		cpu {
+			sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA1>;
+		};
+	};
+
+	hdmi-dai-link {
+		link-name = "HDMI Playback";
+		cpu {
+			sound-dai = <&q6afe HDMI_RX>;
+		};
+
+		platform {
+			sound-dai = <&q6adm>;
+		};
+
+		codec {
+			sound-dai = <&hdmi 0>;
+		};
+	};
+};
diff --git a/dts/Bindings/sound/qcom,q6adm.txt b/dts/Bindings/sound/qcom,q6adm.txt
new file mode 100644
index 0000000000..cb709e5dbc
--- /dev/null
+++ b/dts/Bindings/sound/qcom,q6adm.txt
@@ -0,0 +1,33 @@
+Qualcomm Audio Device Manager (Q6ADM) binding
+
+Q6ADM is one of the APR audio service on Q6DSP.
+Please refer to qcom,apr.txt for details of the coommon apr service bindings
+used by the apr service device.
+
+- but must contain the following property:
+
+- compatible:
+	Usage: required
+	Value type: <stringlist>
+	Definition: must be "qcom,q6adm-v<MAJOR-NUMBER>.<MINOR-NUMBER>".
+		   Or "qcom,q6adm" where the version number can be queried
+		   from DSP.
+		   example "qcom,q6adm-v2.0"
+
+
+= ADM routing
+"routing" subnode of the ADM node represents adm routing specific configuration
+
+- #sound-dai-cells
+	Usage: required
+	Value type: <u32>
+	Definition: Must be 0
+
+= EXAMPLE
+q6adm@8 {
+	compatible = "qcom,q6adm";
+	reg = <APR_SVC_ADM>;
+	q6routing: routing {
+		#sound-dai-cells = <0>;
+	};
+};
diff --git a/dts/Bindings/sound/qcom,q6afe.txt b/dts/Bindings/sound/qcom,q6afe.txt
new file mode 100644
index 0000000000..bdbf87df8c
--- /dev/null
+++ b/dts/Bindings/sound/qcom,q6afe.txt
@@ -0,0 +1,172 @@
+Qualcomm Audio Front End (Q6AFE) binding
+
+AFE is one of the APR audio service on Q6DSP
+Please refer to qcom,apr.txt for details of the common apr service bindings
+used by all apr services. Must contain the following properties.
+
+- compatible:
+	Usage: required
+	Value type: <stringlist>
+	Definition: must be "qcom,q6afe-v<MAJOR-NUMBER>.<MINOR-NUMBER>"
+		  Or "qcom,q6afe" where the version number can be queried
+		  from DSP.
+		  example "qcom,q6afe"
+
+= AFE DAIs (Digial Audio Interface)
+"dais" subnode of the AFE node. It represents afe dais, each afe dai is a
+subnode of "dais" representing board specific dai setup.
+"dais" node should have following properties followed by dai children.
+
+- #sound-dai-cells
+	Usage: required
+	Value type: <u32>
+	Definition: Must be 1
+
+- #address-cells
+	Usage: required
+	Value type: <u32>
+	Definition: Must be 1
+
+- #size-cells
+	Usage: required
+	Value type: <u32>
+	Definition: Must be 0
+
+== AFE DAI is subnode of "dais" and represent a dai, it includes board specific
+configuration of each dai. Must contain the following properties.
+
+- reg
+	Usage: required
+	Value type: <u32>
+	Definition: Must be dai id
+
+- qcom,sd-lines
+	Usage: required for mi2s interface
+	Value type: <prop-encoded-array>
+	Definition: Must be list of serial data lines used by this dai.
+	should be one or more of the 1-4 sd lines.
+
+ - qcom,tdm-sync-mode:
+	Usage: required for tdm interface
+	Value type: <prop-encoded-array>
+	Definition: Synchronization mode.
+		0 - Short sync bit mode
+		1 - Long sync mode
+		2 - Short sync slot mode
+
+ - qcom,tdm-sync-src:
+	Usage: required for tdm interface
+	Value type: <prop-encoded-array>
+	Definition: Synchronization source.
+		0 - External source
+		1 - Internal source
+
+ - qcom,tdm-data-out:
+	Usage: required for tdm interface
+	Value type: <prop-encoded-array>
+	Definition: Data out signal to drive with other masters.
+		0 - Disable
+		1 - Enable
+
+ - qcom,tdm-invert-sync:
+	Usage: required for tdm interface
+	Value type: <prop-encoded-array>
+	Definition: Invert the sync.
+		0 - Normal
+		1 - Invert
+
+ - qcom,tdm-data-delay:
+	Usage: required for tdm interface
+	Value type: <prop-encoded-array>
+	Definition: Number of bit clock to delay data
+		with respect to sync edge.
+		0 - 0 bit clock cycle
+		1 - 1 bit clock cycle
+		2 - 2 bit clock cycle
+
+ - qcom,tdm-data-align:
+	Usage: required for tdm interface
+	Value type: <prop-encoded-array>
+	Definition: Indicate how data is packed
+		within the slot. For example, 32 slot width in case of
+		sample bit width is 24.
+		0 - MSB
+		1 - LSB
+
+= EXAMPLE
+
+q6afe@4 {
+	compatible = "qcom,q6afe";
+	reg = <APR_SVC_AFE>;
+
+	dais {
+		#sound-dai-cells = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		hdmi@1 {
+			reg = <1>;
+		};
+
+		tdm@24 {
+			reg = <24>;
+			qcom,tdm-sync-mode = <1>:
+			qcom,tdm-sync-src = <1>;
+			qcom,tdm-data-out = <0>;
+			qcom,tdm-invert-sync = <1>;
+			qcom,tdm-data-delay = <1>;
+			qcom,tdm-data-align = <0>;
+
+		};
+
+		tdm@25 {
+			reg = <25>;
+			qcom,tdm-sync-mode = <1>:
+			qcom,tdm-sync-src = <1>;
+			qcom,tdm-data-out = <0>;
+			qcom,tdm-invert-sync = <1>;
+			qcom,tdm-data-delay <1>:
+			qcom,tdm-data-align = <0>;
+		};
+
+		prim-mi2s-rx@16 {
+			reg = <16>;
+			qcom,sd-lines = <1 3>;
+		};
+
+		prim-mi2s-tx@17 {
+			reg = <17>;
+			qcom,sd-lines = <2>;
+		};
+
+		sec-mi2s-rx@18 {
+			reg = <18>;
+			qcom,sd-lines = <1 4>;
+		};
+
+		sec-mi2s-tx@19 {
+			reg = <19>;
+			qcom,sd-lines = <2>;
+		};
+
+		tert-mi2s-rx@20 {
+			reg = <20>;
+			qcom,sd-lines = <2 4>;
+		};
+
+		tert-mi2s-tx@21 {
+			reg = <21>;
+			qcom,sd-lines = <1>;
+		};
+
+		quat-mi2s-rx@22 {
+			reg = <22>;
+			qcom,sd-lines = <1>;
+		};
+
+		quat-mi2s-tx@23 {
+			reg = <23>;
+			qcom,sd-lines = <2>;
+		};
+	};
+};
diff --git a/dts/Bindings/sound/qcom,q6asm.txt b/dts/Bindings/sound/qcom,q6asm.txt
new file mode 100644
index 0000000000..2178eb9114
--- /dev/null
+++ b/dts/Bindings/sound/qcom,q6asm.txt
@@ -0,0 +1,33 @@
+Qualcomm Audio Stream Manager (Q6ASM) binding
+
+Q6ASM is one of the APR audio service on Q6DSP.
+Please refer to qcom,apr.txt for details of the common apr service bindings
+used by the apr service device.
+
+- but must contain the following property:
+
+- compatible:
+	Usage: required
+	Value type: <stringlist>
+	Definition: must be "qcom,q6asm-v<MAJOR-NUMBER>.<MINOR-NUMBER>".
+		    Or "qcom,q6asm" where the version number can be queried
+		    from DSP.
+		    example "qcom,q6asm-v2.0"
+
+= ASM DAIs (Digial Audio Interface)
+"dais" subnode of the ASM node represents dai specific configuration
+
+- #sound-dai-cells
+	Usage: required
+	Value type: <u32>
+	Definition: Must be 1
+
+= EXAMPLE
+
+q6asm@7 {
+	compatible = "qcom,q6asm";
+	reg = <APR_SVC_ASM>;
+	q6asmdai: dais {
+		#sound-dai-cells = <1>;
+	};
+};
diff --git a/dts/Bindings/sound/qcom,q6core.txt b/dts/Bindings/sound/qcom,q6core.txt
new file mode 100644
index 0000000000..7f36ff8bec
--- /dev/null
+++ b/dts/Bindings/sound/qcom,q6core.txt
@@ -0,0 +1,21 @@
+Qualcomm ADSP Core service binding
+
+Q6CORE is one of the APR audio service on Q6DSP.
+Please refer to qcom,apr.txt for details of the common apr service bindings
+used by the apr service device.
+
+- but must contain the following property:
+
+- compatible:
+	Usage: required
+	Value type: <stringlist>
+	Definition: must be "qcom,q6core-v<MAJOR-NUMBER>.<MINOR-NUMBER>".
+		   Or "qcom,q6core" where the version number can be queried
+		   from DSP.
+		   example "qcom,q6core-v2.0"
+
+= EXAMPLE
+q6core@3 {
+	compatible = "qcom,q6core";
+	reg = <APR_SVC_ADSP_CORE>;
+};
diff --git a/dts/Bindings/sound/rt274.txt b/dts/Bindings/sound/rt274.txt
index e9a6178c78..791a1bd767 100644
--- a/dts/Bindings/sound/rt274.txt
+++ b/dts/Bindings/sound/rt274.txt
@@ -26,7 +26,7 @@ Pins on the device (for linking into audio routes) for RT274:
 
 Example:
 
-codec: rt274@1c {
+rt274: codec@1c {
 	compatible = "realtek,rt274";
 	reg = <0x1c>;
 	interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
diff --git a/dts/Bindings/sound/rt5514.txt b/dts/Bindings/sound/rt5514.txt
index 4f33b0d96a..b25ed08c7a 100644
--- a/dts/Bindings/sound/rt5514.txt
+++ b/dts/Bindings/sound/rt5514.txt
@@ -32,7 +32,7 @@ Pins on the device (for linking into audio routes) for I2C:
 
 Example:
 
-codec: rt5514@57 {
+rt5514: codec@57 {
 	compatible = "realtek,rt5514";
 	reg = <0x57>;
 };
diff --git a/dts/Bindings/sound/rt5616.txt b/dts/Bindings/sound/rt5616.txt
index e410858185..540a4bf252 100644
--- a/dts/Bindings/sound/rt5616.txt
+++ b/dts/Bindings/sound/rt5616.txt
@@ -26,7 +26,7 @@ Pins on the device (for linking into audio routes) for RT5616:
 
 Example:
 
-codec: rt5616@1b {
+rt5616: codec@1b {
 	compatible = "realtek,rt5616";
 	reg = <0x1b>;
 };
diff --git a/dts/Bindings/sound/rt5640.txt b/dts/Bindings/sound/rt5640.txt
index 57fe646430..e40e4893ee 100644
--- a/dts/Bindings/sound/rt5640.txt
+++ b/dts/Bindings/sound/rt5640.txt
@@ -22,6 +22,41 @@ Optional properties:
 
 - realtek,ldo1-en-gpios : The GPIO that controls the CODEC's LDO1_EN pin.
 
+- realtek,dmic1-data-pin
+  0: dmic1 is not used
+  1: using IN1P pin as dmic1 data pin
+  2: using GPIO3 pin as dmic1 data pin
+
+- realtek,dmic2-data-pin
+  0: dmic2 is not used
+  1: using IN1N pin as dmic2 data pin
+  2: using GPIO4 pin as dmic2 data pin
+
+- realtek,jack-detect-source
+  u32. Valid values:
+  0: jack-detect is not used
+  1: Use GPIO1 for jack-detect
+  2: Use JD1_IN4P for jack-detect
+  3: Use JD2_IN4N for jack-detect
+  4: Use GPIO2 for jack-detect
+  5: Use GPIO3 for jack-detect
+  6: Use GPIO4 for jack-detect
+
+- realtek,jack-detect-not-inverted
+  bool. Normal jack-detect switches give an inverted signal, set this bool
+  in the rare case you've a jack-detect switch which is not inverted.
+
+- realtek,over-current-threshold-microamp
+  u32, micbias over-current detection threshold in µA, valid values are
+  600, 1500 and 2000µA.
+
+- realtek,over-current-scale-factor
+  u32, micbias over-current detection scale-factor, valid values are:
+  0: Scale current by 0.5
+  1: Scale current by 0.75
+  2: Scale current by 1.0
+  3: Scale current by 1.5
+
 Pins on the device (for linking into audio routes) for RT5639/RT5640:
 
   * DMIC1
diff --git a/dts/Bindings/sound/rt5645.txt b/dts/Bindings/sound/rt5645.txt
index 7cee1f518f..a03f9a872a 100644
--- a/dts/Bindings/sound/rt5645.txt
+++ b/dts/Bindings/sound/rt5645.txt
@@ -69,4 +69,4 @@ codec: rt5650@1a {
 	realtek,dmic-en = "true";
 	realtek,en-jd-func = "true";
 	realtek,jd-mode = <3>;
-};
\ No newline at end of file
+};
diff --git a/dts/Bindings/sound/rt5651.txt b/dts/Bindings/sound/rt5651.txt
index b85221864c..a41199a5cd 100644
--- a/dts/Bindings/sound/rt5651.txt
+++ b/dts/Bindings/sound/rt5651.txt
@@ -50,7 +50,7 @@ Pins on the device (for linking into audio routes) for RT5651:
 
 Example:
 
-codec: rt5651@1a {
+rt5651: codec@1a {
 	compatible = "realtek,rt5651";
 	reg = <0x1a>;
 	realtek,dmic-en = "true";
diff --git a/dts/Bindings/sound/rt5663.txt b/dts/Bindings/sound/rt5663.txt
index 497bcfc58b..23386446c6 100644
--- a/dts/Bindings/sound/rt5663.txt
+++ b/dts/Bindings/sound/rt5663.txt
@@ -47,7 +47,7 @@ Pins on the device (for linking into audio routes) for RT5663:
 
 Example:
 
-codec: rt5663@12 {
+rt5663: codec@12 {
 	compatible = "realtek,rt5663";
 	reg = <0x12>;
 	interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
diff --git a/dts/Bindings/sound/rt5668.txt b/dts/Bindings/sound/rt5668.txt
new file mode 100644
index 0000000000..c88b96e776
--- /dev/null
+++ b/dts/Bindings/sound/rt5668.txt
@@ -0,0 +1,50 @@
+RT5668B audio CODEC
+
+This device supports I2C only.
+
+Required properties:
+
+- compatible : "realtek,rt5668b"
+
+- reg : The I2C address of the device.
+
+Optional properties:
+
+- interrupts : The CODEC's interrupt output.
+
+- realtek,dmic1-data-pin
+  0: dmic1 is not used
+  1: using GPIO2 pin as dmic1 data pin
+  2: using GPIO5 pin as dmic1 data pin
+
+- realtek,dmic1-clk-pin
+  0: using GPIO1 pin as dmic1 clock pin
+  1: using GPIO3 pin as dmic1 clock pin
+
+- realtek,jd-src
+  0: No JD is used
+  1: using JD1 as JD source
+
+- realtek,ldo1-en-gpios : The GPIO that controls the CODEC's LDO1_EN pin.
+
+Pins on the device (for linking into audio routes) for RT5668B:
+
+  * DMIC L1
+  * DMIC R1
+  * IN1P
+  * HPOL
+  * HPOR
+
+Example:
+
+rt5668 {
+	compatible = "realtek,rt5668b";
+	reg = <0x1a>;
+	interrupt-parent = <&gpio>;
+	interrupts = <TEGRA_GPIO(U, 6) GPIO_ACTIVE_HIGH>;
+	realtek,ldo1-en-gpios =
+		<&gpio TEGRA_GPIO(R, 2) GPIO_ACTIVE_HIGH>;
+	realtek,dmic1-data-pin = <1>;
+	realtek,dmic1-clk-pin = <1>;
+	realtek,jd-src = <1>;
+};
diff --git a/dts/Bindings/sound/sgtl5000.txt b/dts/Bindings/sound/sgtl5000.txt
index 9a36c7e2a1..0f21445747 100644
--- a/dts/Bindings/sound/sgtl5000.txt
+++ b/dts/Bindings/sound/sgtl5000.txt
@@ -39,7 +39,7 @@ VDDIO		1.8V		2.5V		3.3V
 
 Example:
 
-codec: sgtl5000@a {
+sgtl5000: codec@a {
 	compatible = "fsl,sgtl5000";
 	reg = <0x0a>;
 	#sound-dai-cells = <0>;
diff --git a/dts/Bindings/sound/simple-card.txt b/dts/Bindings/sound/simple-card.txt
index 17c13e7466..a4c72d09cd 100644
--- a/dts/Bindings/sound/simple-card.txt
+++ b/dts/Bindings/sound/simple-card.txt
@@ -86,6 +86,11 @@ Optional CPU/CODEC subnodes properties:
 					  in dai startup() and disabled with
 					  clk_disable_unprepare() in dai
 					  shutdown().
+					  If a clock is specified and a
+					  multiplication factor is given with
+					  mclk-fs, the clock will be set to the
+					  calculated mclk frequency when the
+					  stream starts.
 - system-clock-direction-out		: specifies clock direction as 'out' on
 					  initialization. It is useful for some aCPUs with
 					  fixed clocks.
diff --git a/dts/Bindings/sound/st,stm32-i2s.txt b/dts/Bindings/sound/st,stm32-i2s.txt
index 4bda520424..58c3413005 100644
--- a/dts/Bindings/sound/st,stm32-i2s.txt
+++ b/dts/Bindings/sound/st,stm32-i2s.txt
@@ -18,7 +18,7 @@ Required properties:
     See Documentation/devicetree/bindings/dma/stm32-dma.txt.
   - dma-names: Identifier for each DMA request line. Must be "tx" and "rx".
   - pinctrl-names: should contain only value "default"
-  - pinctrl-0: see Documentation/devicetree/bindings/pinctrl/pinctrl-stm32.txt
+  - pinctrl-0: see Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt
 
 Optional properties:
   - resets: Reference to a reset controller asserting the reset controller
diff --git a/dts/Bindings/sound/st,stm32-sai.txt b/dts/Bindings/sound/st,stm32-sai.txt
index f301cdf0b7..3a3fc506e4 100644
--- a/dts/Bindings/sound/st,stm32-sai.txt
+++ b/dts/Bindings/sound/st,stm32-sai.txt
@@ -37,7 +37,7 @@ SAI subnodes required properties:
 	"tx": if sai sub-block is configured as playback DAI
 	"rx": if sai sub-block is configured as capture DAI
   - pinctrl-names: should contain only value "default"
-  - pinctrl-0: see Documentation/devicetree/bindings/pinctrl/pinctrl-stm32.txt
+  - pinctrl-0: see Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt
 
 SAI subnodes Optional properties:
   - st,sync: specify synchronization mode.
diff --git a/dts/Bindings/sound/ti,tas6424.txt b/dts/Bindings/sound/ti,tas6424.txt
index 1c4ada0eef..eacb54f341 100644
--- a/dts/Bindings/sound/ti,tas6424.txt
+++ b/dts/Bindings/sound/ti,tas6424.txt
@@ -6,6 +6,8 @@ Required properties:
 	- compatible: "ti,tas6424" - TAS6424
 	- reg: I2C slave address
 	- sound-dai-cells: must be equal to 0
+	- standby-gpios: GPIO used to shut the TAS6424 down.
+	- mute-gpios: GPIO used to mute all the outputs
 
 Example:
 
diff --git a/dts/Bindings/sound/tscs42xx.txt b/dts/Bindings/sound/tscs42xx.txt
index 2ac2f09966..7eea32e9d0 100644
--- a/dts/Bindings/sound/tscs42xx.txt
+++ b/dts/Bindings/sound/tscs42xx.txt
@@ -8,9 +8,15 @@ Required Properties:
 	- reg : 	<0x71> for analog mic
 			<0x69> for digital mic
 
+	- clock-names:	Must one of  the following "mclk1", "xtal", "mclk2"
+
+	- clocks:	phandle of the clock that provides the codec sysclk
+
 Example:
 
 wookie: codec@69 {
 	compatible = "tempo,tscs42A2";
 	reg = <0x69>;
+	clock-names = "xtal";
+	clocks = <&audio_xtal>;
 };
diff --git a/dts/Bindings/sound/tscs454.txt b/dts/Bindings/sound/tscs454.txt
new file mode 100644
index 0000000000..3ba3e2d2c2
--- /dev/null
+++ b/dts/Bindings/sound/tscs454.txt
@@ -0,0 +1,23 @@
+TSCS454 Audio CODEC
+
+Required Properties:
+
+	- compatible :	"tempo,tscs454"
+
+	- reg : 	<0x69>
+
+	- clock-names:	Must one of  the following "xtal", "mclk1", "mclk2"
+
+	- clocks:	phandle of the clock that provides the codec sysclk
+
+	Note: If clock is not provided then bit clock is assumed
+
+Example:
+
+redwood: codec@69 {
+	#sound-dai-cells = <1>;
+	compatible = "tempo,tscs454";
+	reg = <0x69>;
+	clock-names = "mclk1";
+	clocks = <&audio_mclk>;
+};
diff --git a/dts/Bindings/sound/wm8510.txt b/dts/Bindings/sound/wm8510.txt
index fa1a32b855..e6b6cc041f 100644
--- a/dts/Bindings/sound/wm8510.txt
+++ b/dts/Bindings/sound/wm8510.txt
@@ -12,7 +12,7 @@ Required properties:
 
 Example:
 
-codec: wm8510@1a {
+wm8510: codec@1a {
 	compatible = "wlf,wm8510";
 	reg = <0x1a>;
 };
diff --git a/dts/Bindings/sound/wm8523.txt b/dts/Bindings/sound/wm8523.txt
index 04746186b2..f3a6485f4b 100644
--- a/dts/Bindings/sound/wm8523.txt
+++ b/dts/Bindings/sound/wm8523.txt
@@ -10,7 +10,7 @@ Required properties:
 
 Example:
 
-codec: wm8523@1a {
+wm8523: codec@1a {
 	compatible = "wlf,wm8523";
 	reg = <0x1a>;
 };
diff --git a/dts/Bindings/sound/wm8524.txt b/dts/Bindings/sound/wm8524.txt
index 0f0553563f..f6c0c263b1 100644
--- a/dts/Bindings/sound/wm8524.txt
+++ b/dts/Bindings/sound/wm8524.txt
@@ -10,7 +10,7 @@ Required properties:
 
 Example:
 
-codec: wm8524 {
+wm8524: codec {
 	compatible = "wlf,wm8524";
 	wlf,mute-gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
 };
diff --git a/dts/Bindings/sound/wm8580.txt b/dts/Bindings/sound/wm8580.txt
index 78fce9b149..ff3f9f5f21 100644
--- a/dts/Bindings/sound/wm8580.txt
+++ b/dts/Bindings/sound/wm8580.txt
@@ -10,7 +10,7 @@ Required properties:
 
 Example:
 
-codec: wm8580@1a {
+wm8580: codec@1a {
 	compatible = "wlf,wm8580";
 	reg = <0x1a>;
 };
diff --git a/dts/Bindings/sound/wm8711.txt b/dts/Bindings/sound/wm8711.txt
index 8ed9998cd2..c30a1387c4 100644
--- a/dts/Bindings/sound/wm8711.txt
+++ b/dts/Bindings/sound/wm8711.txt
@@ -12,7 +12,7 @@ Required properties:
 
 Example:
 
-codec: wm8711@1a {
+wm8711: codec@1a {
 	compatible = "wlf,wm8711";
 	reg = <0x1a>;
 };
diff --git a/dts/Bindings/sound/wm8728.txt b/dts/Bindings/sound/wm8728.txt
index a8b5c3668e..a3608b4c78 100644
--- a/dts/Bindings/sound/wm8728.txt
+++ b/dts/Bindings/sound/wm8728.txt
@@ -12,7 +12,7 @@ Required properties:
 
 Example:
 
-codec: wm8728@1a {
+wm8728: codec@1a {
 	compatible = "wlf,wm8728";
 	reg = <0x1a>;
 };
diff --git a/dts/Bindings/sound/wm8731.txt b/dts/Bindings/sound/wm8731.txt
index 236690e99b..f660d9bb0e 100644
--- a/dts/Bindings/sound/wm8731.txt
+++ b/dts/Bindings/sound/wm8731.txt
@@ -12,7 +12,7 @@ Required properties:
 
 Example:
 
-codec: wm8731@1a {
+wm8731: codec@1a {
 	compatible = "wlf,wm8731";
 	reg = <0x1a>;
 };
diff --git a/dts/Bindings/sound/wm8737.txt b/dts/Bindings/sound/wm8737.txt
index 4bc2cea3b1..eda1ec6a75 100644
--- a/dts/Bindings/sound/wm8737.txt
+++ b/dts/Bindings/sound/wm8737.txt
@@ -12,7 +12,7 @@ Required properties:
 
 Example:
 
-codec: wm8737@1a {
+wm8737: codec@1a {
 	compatible = "wlf,wm8737";
 	reg = <0x1a>;
 };
diff --git a/dts/Bindings/sound/wm8741.txt b/dts/Bindings/sound/wm8741.txt
index a133154087..b69e196c74 100644
--- a/dts/Bindings/sound/wm8741.txt
+++ b/dts/Bindings/sound/wm8741.txt
@@ -21,7 +21,7 @@ Optional properties:
 
 Example:
 
-codec: wm8741@1a {
+wm8741: codec@1a {
 	compatible = "wlf,wm8741";
 	reg = <0x1a>;
 
diff --git a/dts/Bindings/sound/wm8750.txt b/dts/Bindings/sound/wm8750.txt
index 8db239fd5e..682f221f6f 100644
--- a/dts/Bindings/sound/wm8750.txt
+++ b/dts/Bindings/sound/wm8750.txt
@@ -12,7 +12,7 @@ Required properties:
 
 Example:
 
-codec: wm8750@1a {
+wm8750: codec@1a {
 	compatible = "wlf,wm8750";
 	reg = <0x1a>;
 };
diff --git a/dts/Bindings/sound/wm8753.txt b/dts/Bindings/sound/wm8753.txt
index 8eee612821..eca9e5a825 100644
--- a/dts/Bindings/sound/wm8753.txt
+++ b/dts/Bindings/sound/wm8753.txt
@@ -34,7 +34,7 @@ Pins on the device (for linking into audio routes):
 
 Example:
 
-codec: wm8753@1a {
+wm8753: codec@1a {
 	compatible = "wlf,wm8753";
 	reg = <0x1a>;
 };
diff --git a/dts/Bindings/sound/wm8770.txt b/dts/Bindings/sound/wm8770.txt
index 866e00ca15..cac762a110 100644
--- a/dts/Bindings/sound/wm8770.txt
+++ b/dts/Bindings/sound/wm8770.txt
@@ -10,7 +10,7 @@ Required properties:
 
 Example:
 
-codec: wm8770@1 {
+wm8770: codec@1 {
 	compatible = "wlf,wm8770";
 	reg = <1>;
 };
diff --git a/dts/Bindings/sound/wm8776.txt b/dts/Bindings/sound/wm8776.txt
index 3b9ca49abc..01173369c3 100644
--- a/dts/Bindings/sound/wm8776.txt
+++ b/dts/Bindings/sound/wm8776.txt
@@ -12,7 +12,7 @@ Required properties:
 
 Example:
 
-codec: wm8776@1a {
+wm8776: codec@1a {
 	compatible = "wlf,wm8776";
 	reg = <0x1a>;
 };
diff --git a/dts/Bindings/sound/wm8804.txt b/dts/Bindings/sound/wm8804.txt
index 6fd124b164..2c1641c17a 100644
--- a/dts/Bindings/sound/wm8804.txt
+++ b/dts/Bindings/sound/wm8804.txt
@@ -19,7 +19,7 @@ Optional properties:
 
 Example:
 
-codec: wm8804@1a {
+wm8804: codec@1a {
 	compatible = "wlf,wm8804";
 	reg = <0x1a>;
 };
diff --git a/dts/Bindings/sound/wm8903.txt b/dts/Bindings/sound/wm8903.txt
index afc51caf11..6371c2434a 100644
--- a/dts/Bindings/sound/wm8903.txt
+++ b/dts/Bindings/sound/wm8903.txt
@@ -57,7 +57,7 @@ Pins on the device (for linking into audio routes):
 
 Example:
 
-codec: wm8903@1a {
+wm8903: codec@1a {
 	compatible = "wlf,wm8903";
 	reg = <0x1a>;
 	interrupts = < 347 >;
diff --git a/dts/Bindings/sound/wm8960.txt b/dts/Bindings/sound/wm8960.txt
index 2deb8a3da9..6d29ac3750 100644
--- a/dts/Bindings/sound/wm8960.txt
+++ b/dts/Bindings/sound/wm8960.txt
@@ -23,7 +23,7 @@ Optional properties:
 
 Example:
 
-codec: wm8960@1a {
+wm8960: codec@1a {
 	compatible = "wlf,wm8960";
 	reg = <0x1a>;
 
diff --git a/dts/Bindings/sound/wm8962.txt b/dts/Bindings/sound/wm8962.txt
index 7f82b59ec8..dcfa9a3369 100644
--- a/dts/Bindings/sound/wm8962.txt
+++ b/dts/Bindings/sound/wm8962.txt
@@ -24,7 +24,7 @@ Optional properties:
 
 Example:
 
-codec: wm8962@1a {
+wm8962: codec@1a {
 	compatible = "wlf,wm8962";
 	reg = <0x1a>;
 
diff --git a/dts/Bindings/sound/wm8994.txt b/dts/Bindings/sound/wm8994.txt
index 68c4e8d96b..4a9dead1b7 100644
--- a/dts/Bindings/sound/wm8994.txt
+++ b/dts/Bindings/sound/wm8994.txt
@@ -59,7 +59,7 @@ Optional properties:
 
 Example:
 
-codec: wm8994@1a {
+wm8994: codec@1a {
 	compatible = "wlf,wm8994";
 	reg = <0x1a>;