dts: update to v4.13-rc2

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>

5 files changed, 139 insertions, 31 deletions

diff --git a/dts/Bindings/spi/sh-msiof.txt b/dts/Bindings/spi/sh-msiof.txt
index dc975064fa..64ee489571 100644
--- a/dts/Bindings/spi/sh-msiof.txt
+++ b/dts/Bindings/spi/sh-msiof.txt
@@ -38,6 +38,8 @@ Optional properties:
 			 specifiers, one for transmission, and one for
 			 reception.
 - dma-names            : Must contain a list of two DMA names, "tx" and "rx".
+- spi-slave            : Empty property indicating the SPI controller is used
+			 in slave mode.
 - renesas,dtdl         : delay sync signal (setup) in transmit mode.
 			 Must contain one of the following values:
 			 0   (no bit delay)
diff --git a/dts/Bindings/spi/spi-bus.txt b/dts/Bindings/spi/spi-bus.txt
index 4b1d6e74c7..1f6e86f787 100644
--- a/dts/Bindings/spi/spi-bus.txt
+++ b/dts/Bindings/spi/spi-bus.txt
@@ -1,17 +1,23 @@
 SPI (Serial Peripheral Interface) busses
 
-SPI busses can be described with a node for the SPI master device
-and a set of child nodes for each SPI slave on the bus.  For this
-discussion, it is assumed that the system's SPI controller is in
-SPI master mode.  This binding does not describe SPI controllers
-in slave mode.
+SPI busses can be described with a node for the SPI controller device
+and a set of child nodes for each SPI slave on the bus.  The system's SPI
+controller may be described for use in SPI master mode or in SPI slave mode,
+but not for both at the same time.
 
-The SPI master node requires the following properties:
+The SPI controller node requires the following properties:
+- compatible      - Name of SPI bus controller following generic names
+		    recommended practice.
+
+In master mode, the SPI controller node requires the following additional
+properties:
 - #address-cells  - number of cells required to define a chip select
 		address on the SPI bus.
 - #size-cells     - should be zero.
-- compatible      - name of SPI bus controller following generic names
-		recommended practice.
+
+In slave mode, the SPI controller node requires one additional property:
+- spi-slave       - Empty property.
+
 No other properties are required in the SPI bus node.  It is assumed
 that a driver for an SPI bus device will understand that it is an SPI bus.
 However, the binding does not attempt to define the specific method for
@@ -21,7 +27,7 @@ assumption that board specific platform code will be used to manage
 chip selects.  Individual drivers can define additional properties to
 support describing the chip select layout.
 
-Optional properties:
+Optional properties (master mode only):
 - cs-gpios	  - gpios chip select.
 - num-cs	  - total number of chipselects.
 
@@ -41,28 +47,36 @@ cs1 : native
 cs2 : &gpio1 1 0
 cs3 : &gpio1 2 0
 
-SPI slave nodes must be children of the SPI master node and can
-contain the following properties.
-- reg             - (required) chip select address of device.
-- compatible      - (required) name of SPI device following generic names
-		recommended practice.
-- spi-max-frequency - (required) Maximum SPI clocking speed of device in Hz.
-- spi-cpol        - (optional) Empty property indicating device requires
-		inverse clock polarity (CPOL) mode.
-- spi-cpha        - (optional) Empty property indicating device requires
-		shifted clock phase (CPHA) mode.
-- spi-cs-high     - (optional) Empty property indicating device requires
-		chip select active high.
-- spi-3wire       - (optional) Empty property indicating device requires
-		3-wire mode.
-- spi-lsb-first   - (optional) Empty property indicating device requires
-		LSB first mode.
-- spi-tx-bus-width - (optional) The bus width (number of data wires) that is
-                      used for MOSI. Defaults to 1 if not present.
-- spi-rx-bus-width - (optional) The bus width (number of data wires) that is
-                      used for MISO. Defaults to 1 if not present.
-- spi-rx-delay-us  - (optional) Microsecond delay after a read transfer.
-- spi-tx-delay-us  - (optional) Microsecond delay after a write transfer.
+
+SPI slave nodes must be children of the SPI controller node.
+
+In master mode, one or more slave nodes (up to the number of chip selects) can
+be present.  Required properties are:
+- compatible      - Name of SPI device following generic names recommended
+		    practice.
+- reg             - Chip select address of device.
+- spi-max-frequency - Maximum SPI clocking speed of device in Hz.
+
+In slave mode, the (single) slave node is optional.
+If present, it must be called "slave".  Required properties are:
+- compatible      - Name of SPI device following generic names recommended
+		    practice.
+
+All slave nodes can contain the following optional properties:
+- spi-cpol        - Empty property indicating device requires inverse clock
+		    polarity (CPOL) mode.
+- spi-cpha        - Empty property indicating device requires shifted clock
+		    phase (CPHA) mode.
+- spi-cs-high     - Empty property indicating device requires chip select
+		    active high.
+- spi-3wire       - Empty property indicating device requires 3-wire mode.
+- spi-lsb-first   - Empty property indicating device requires LSB first mode.
+- spi-tx-bus-width - The bus width (number of data wires) that is used for MOSI.
+		    Defaults to 1 if not present.
+- spi-rx-bus-width - The bus width (number of data wires) that is used for MISO.
+		    Defaults to 1 if not present.
+- spi-rx-delay-us - Microsecond delay after a read transfer.
+- spi-tx-delay-us - Microsecond delay after a write transfer.
 
 Some SPI controllers and devices support Dual and Quad SPI transfer mode.
 It allows data in the SPI system to be transferred using 2 wires (DUAL) or 4
diff --git a/dts/Bindings/spi/spi-meson.txt b/dts/Bindings/spi/spi-meson.txt
index dc6d031332..825c39cae7 100644
--- a/dts/Bindings/spi/spi-meson.txt
+++ b/dts/Bindings/spi/spi-meson.txt
@@ -20,3 +20,34 @@ Required properties:
 		#address-cells = <1>;
 		#size-cells = <0>;
 	};
+
+* SPICC (SPI Communication Controller)
+
+The Meson SPICC is generic SPI controller for general purpose Full-Duplex
+communications with dedicated 16 words RX/TX PIO FIFOs.
+
+Required properties:
+ - compatible: should be "amlogic,meson-gx-spicc" on Amlogic GX SoCs.
+ - reg: physical base address and length of the controller registers
+ - interrupts: The interrupt specifier
+ - clock-names: Must contain "core"
+ - clocks: phandle of the input clock for the baud rate generator
+ - #address-cells: should be 1
+ - #size-cells: should be 0
+
+Optional properties:
+ - resets: phandle of the internal reset line
+
+See ../spi/spi-bus.txt for more details on SPI bus master and slave devices
+required and optional properties.
+
+Example :
+	spi@c1108d80 {
+		compatible = "amlogic,meson-gx-spicc";
+		reg = <0xc1108d80 0x80>;
+		interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
+		clock-names = "core";
+		clocks = <&clk81>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
diff --git a/dts/Bindings/spi/spi-mt65xx.txt b/dts/Bindings/spi/spi-mt65xx.txt
index e43f4cf4cf..e0318cf92d 100644
--- a/dts/Bindings/spi/spi-mt65xx.txt
+++ b/dts/Bindings/spi/spi-mt65xx.txt
@@ -3,7 +3,9 @@ Binding for MTK SPI controller
 Required properties:
 - compatible: should be one of the following.
     - mediatek,mt2701-spi: for mt2701 platforms
+    - mediatek,mt2712-spi: for mt2712 platforms
     - mediatek,mt6589-spi: for mt6589 platforms
+    - mediatek,mt7622-spi: for mt7622 platforms
     - mediatek,mt8135-spi: for mt8135 platforms
     - mediatek,mt8173-spi: for mt8173 platforms
 
diff --git a/dts/Bindings/spi/spi-stm32.txt b/dts/Bindings/spi/spi-stm32.txt
new file mode 100644
index 0000000000..1b3fa2c119
--- /dev/null
+++ b/dts/Bindings/spi/spi-stm32.txt
@@ -0,0 +1,59 @@
+STMicroelectronics STM32 SPI Controller
+
+The STM32 SPI controller is used to communicate with external devices using
+the Serial Peripheral Interface. It supports full-duplex, half-duplex and
+simplex synchronous serial communication with external devices. It supports
+from 4 to 32-bit data size. Although it can be configured as master or slave,
+only master is supported by the driver.
+
+Required properties:
+- compatible: Must be "st,stm32h7-spi".
+- reg: Offset and length of the device's register set.
+- interrupts: Must contain the interrupt id.
+- clocks: Must contain an entry for spiclk (which feeds the internal clock
+	  generator).
+- #address-cells:  Number of cells required to define a chip select address.
+- #size-cells: Should be zero.
+
+Optional properties:
+- resets: Must contain the phandle to the reset controller.
+- A pinctrl state named "default" may be defined to set pins in mode of
+  operation for SPI transfer.
+- dmas: DMA specifiers for tx and rx dma. DMA fifo mode must be used. See the
+  STM32 DMA bindings, Documentation/devicetree/bindings/dma/stm32-dma.txt.
+- dma-names: DMA request names should include "tx" and "rx" if present.
+- cs-gpios: list of GPIO chip selects. See the SPI bus bindings,
+  Documentation/devicetree/bindings/spi/spi-bus.txt
+
+
+Child nodes represent devices on the SPI bus
+  See ../spi/spi-bus.txt
+
+Optional properties:
+- st,spi-midi-ns: (Master Inter-Data Idleness) minimum time delay in
+		  nanoseconds inserted between two consecutive data frames.
+
+
+Example:
+	spi2: spi@40003800 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "st,stm32h7-spi";
+		reg = <0x40003800 0x400>;
+		interrupts = <36>;
+		clocks = <&rcc SPI2_CK>;
+		resets = <&rcc 1166>;
+		dmas = <&dmamux1 0 39 0x400 0x01>,
+		       <&dmamux1 1 40 0x400 0x01>;
+		dma-names = "rx", "tx";
+		pinctrl-0 = <&spi2_pins_b>;
+		pinctrl-names = "default";
+		cs-gpios = <&gpioa 11 0>;
+
+		aardvark@0 {
+			compatible = "totalphase,aardvark";
+			reg = <0>;
+			spi-max-frequency = <4000000>;
+			st,spi-midi-ns = <4000>;
+		};
+	};