dts: update to v4.16-rc1

Also includeded:

ARM: dts: am33xx: do not delete no longer existing clocks

Several clocks are removed from the am33xx dts files with v4.16-rc1.
Remove the corresponding /delete-node/ directives aswell to avoid
dtc breakage.

Also included:

ARM: dts: imx6qdl: SolidRun: Fix upstream include

Upstream dts file way renamed, so change include name accordingly.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

6 files changed, 96 insertions, 14 deletions

diff --git a/dts/Bindings/usb/dwc3.txt b/dts/Bindings/usb/dwc3.txt
index 52fb41046b..44e8bab159 100644
--- a/dts/Bindings/usb/dwc3.txt
+++ b/dts/Bindings/usb/dwc3.txt
@@ -47,6 +47,8 @@ Optional properties:
 			from P0 to P1/P2/P3 without delay.
  - snps,dis-tx-ipgap-linecheck-quirk: when set, disable u2mac linestate check
 			during HS transmit.
+ - snps,dis_metastability_quirk: when set, disable metastability workaround.
+			CAUTION: use only if you are absolutely sure of it.
  - snps,is-utmi-l1-suspend: true when DWC3 asserts output signal
 			utmi_l1_suspend_n, false when asserts utmi_sleep_n
  - snps,hird-threshold: HIRD threshold
diff --git a/dts/Bindings/usb/mediatek,mtk-xhci.txt b/dts/Bindings/usb/mediatek,mtk-xhci.txt
index 3059596487..88d9f4a4b2 100644
--- a/dts/Bindings/usb/mediatek,mtk-xhci.txt
+++ b/dts/Bindings/usb/mediatek,mtk-xhci.txt
@@ -35,10 +35,14 @@ Required properties:
  - phys : a list of phandle + phy specifier pairs
 
 Optional properties:
- - mediatek,wakeup-src : 1: ip sleep wakeup mode; 2: line state wakeup
-	mode;
- - mediatek,syscon-wakeup : phandle to syscon used to access USB wakeup
-	control register, it depends on "mediatek,wakeup-src".
+ - wakeup-source : enable USB remote wakeup;
+ - mediatek,syscon-wakeup : phandle to syscon used to access the register
+	of the USB wakeup glue layer between xHCI and SPM; it depends on
+	"wakeup-source", and has two arguments:
+	- the first one : register base address of the glue layer in syscon;
+	- the second one : hardware version of the glue layer
+		- 1 : used by mt8173 etc
+		- 2 : used by mt2712 etc
  - mediatek,u3p-dis-msk : mask to disable u3ports, bit0 for u3port0,
 	bit1 for u3port1, ... etc;
  - vbus-supply : reference to the VBUS regulator;
@@ -46,6 +50,7 @@ Optional properties:
  - pinctrl-names : a pinctrl state named "default" must be defined
  - pinctrl-0 : pin control group
 	See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
+ - imod-interval-ns: default interrupt moderation interval is 5000ns
 
 Example:
 usb30: usb@11270000 {
@@ -64,8 +69,9 @@ usb30: usb@11270000 {
 	vusb33-supply = <&mt6397_vusb_reg>;
 	vbus-supply = <&usb_p1_vbus>;
 	usb3-lpm-capable;
-	mediatek,syscon-wakeup = <&pericfg>;
-	mediatek,wakeup-src = <1>;
+	mediatek,syscon-wakeup = <&pericfg 0x400 1>;
+	wakeup-source;
+	imod-interval-ns = <10000>;
 };
 
 2nd: dual-role mode with xHCI driver
diff --git a/dts/Bindings/usb/mediatek,mtu3.txt b/dts/Bindings/usb/mediatek,mtu3.txt
index b2271d8e6b..d589a1ef96 100644
--- a/dts/Bindings/usb/mediatek,mtu3.txt
+++ b/dts/Bindings/usb/mediatek,mtu3.txt
@@ -42,9 +42,14 @@ Optional properties:
  - enable-manual-drd : supports manual dual-role switch via debugfs; usually
 	used when receptacle is TYPE-A and also wants to support dual-role
 	mode.
- - mediatek,enable-wakeup : supports ip sleep wakeup used by host mode
- - mediatek,syscon-wakeup : phandle to syscon used to access USB wakeup
-	control register, it depends on "mediatek,enable-wakeup".
+ - wakeup-source: enable USB remote wakeup of host mode.
+ - mediatek,syscon-wakeup : phandle to syscon used to access the register
+	of the USB wakeup glue layer between SSUSB and SPM; it depends on
+	"wakeup-source", and has two arguments:
+	- the first one : register base address of the glue layer in syscon;
+	- the second one : hardware version of the glue layer
+		- 1 : used by mt8173 etc
+		- 2 : used by mt2712 etc
  - mediatek,u3p-dis-msk : mask to disable u3ports, bit0 for u3port0,
 	bit1 for u3port1, ... etc;
 
@@ -71,8 +76,8 @@ ssusb: usb@11271000 {
 	vbus-supply = <&usb_p0_vbus>;
 	extcon = <&extcon_usb>;
 	dr_mode = "otg";
-	mediatek,enable-wakeup;
-	mediatek,syscon-wakeup = <&pericfg>;
+	wakeup-source;
+	mediatek,syscon-wakeup = <&pericfg 0x400 1>;
 	#address-cells = <2>;
 	#size-cells = <2>;
 	ranges;
diff --git a/dts/Bindings/usb/renesas_usbhs.txt b/dts/Bindings/usb/renesas_usbhs.txt
index 47394ab788..d060172f15 100644
--- a/dts/Bindings/usb/renesas_usbhs.txt
+++ b/dts/Bindings/usb/renesas_usbhs.txt
@@ -13,8 +13,10 @@ Required properties:
 	- "renesas,usbhs-r8a7795" for r8a7795 (R-Car H3) compatible device
 	- "renesas,usbhs-r8a7796" for r8a7796 (R-Car M3-W) compatible device
 	- "renesas,usbhs-r8a77995" for r8a77995 (R-Car D3) compatible device
+	- "renesas,usbhs-r7s72100" for r7s72100 (RZ/A1) compatible device
 	- "renesas,rcar-gen2-usbhs" for R-Car Gen2 or RZ/G1 compatible devices
 	- "renesas,rcar-gen3-usbhs" for R-Car Gen3 compatible device
+	- "renesas,rza1-usbhs" for RZ/A1 compatible device
 
 	When compatible with the generic version, nodes must list the
 	SoC-specific version corresponding to the platform first followed
diff --git a/dts/Bindings/usb/usb-device.txt b/dts/Bindings/usb/usb-device.txt
index 1b27cebb47..036be172b1 100644
--- a/dts/Bindings/usb/usb-device.txt
+++ b/dts/Bindings/usb/usb-device.txt
@@ -4,8 +4,49 @@ Usually, we only use device tree for hard wired USB device.
 The reference binding doc is from:
 http://www.devicetree.org/open-firmware/bindings/usb/usb-1_0.ps
 
+Four types of device-tree nodes are defined: "host-controller nodes"
+representing USB host controllers, "device nodes" representing USB devices,
+"interface nodes" representing USB interfaces and "combined nodes"
+representing simple USB devices.
 
-Required properties:
+A combined node shall be used instead of a device node and an interface node
+for devices of class 0 or 9 (hub) with a single configuration and a single
+interface.
+
+A "hub node" is a combined node or an interface node that represents a USB
+hub.
+
+
+Required properties for device nodes:
+- compatible: "usbVID,PID", where VID is the vendor id and PID the product id.
+  The textual representation of VID and PID shall be in lower case hexadecimal
+  with leading zeroes suppressed. The other compatible strings from the above
+  standard binding could also be used, but a device adhering to this binding
+  may leave out all except for "usbVID,PID".
+- reg: the number of the USB hub port or the USB host-controller port to which
+  this device is attached. The range is 1-255.
+
+
+Required properties for device nodes with interface nodes:
+- #address-cells: shall be 2
+- #size-cells: shall be 0
+
+
+Required properties for interface nodes:
+- compatible: "usbifVID,PID.configCN.IN", where VID is the vendor id, PID is
+  the product id, CN is the configuration value and IN is the interface
+  number. The textual representation of VID, PID, CN and IN shall be in lower
+  case hexadecimal with leading zeroes suppressed. The other compatible
+  strings from the above standard binding could also be used, but a device
+  adhering to this binding may leave out all except for
+  "usbifVID,PID.configCN.IN".
+- reg: the interface number and configuration value
+
+The configuration component is not included in the textual representation of
+an interface-node unit address for configuration 1.
+
+
+Required properties for combined nodes:
 - compatible: "usbVID,PID", where VID is the vendor id and PID the product id.
   The textual representation of VID and PID shall be in lower case hexadecimal
   with leading zeroes suppressed. The other compatible strings from the above
@@ -31,8 +72,31 @@ Example:
 	#address-cells = <1>;
 	#size-cells = <0>;
 
-	hub@1 {	/* hub connected to port 1 */
+	hub@1 {		/* hub connected to port 1 */
 		compatible = "usb5e3,608";
 		reg = <1>;
 	};
+
+	device@2 {	/* device connected to port 2 */
+		compatible = "usb123,4567";
+		reg = <2>;
+	};
+
+	device@3 { 	/* device connected to port 3 */
+		compatible = "usb123,abcd";
+		reg = <3>;
+
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		interface@0 {	/* interface 0 of configuration 1 */
+			compatible = "usbif123,abcd.config1.0";
+			reg = <0 1>;
+		};
+
+		interface@0,2 {	/* interface 0 of configuration 2 */
+			compatible = "usbif123,abcd.config2.0";
+			reg = <0 2>;
+		};
+	};
 };
diff --git a/dts/Bindings/usb/usb-xhci.txt b/dts/Bindings/usb/usb-xhci.txt
index ae6e484a8d..e2ea59bbca 100644
--- a/dts/Bindings/usb/usb-xhci.txt
+++ b/dts/Bindings/usb/usb-xhci.txt
@@ -7,12 +7,14 @@ Required properties:
     - "marvell,armada3700-xhci" for Armada 37xx SoCs
     - "marvell,armada-375-xhci" for Armada 375 SoCs
     - "marvell,armada-380-xhci" for Armada 38x SoCs
+    - "renesas,xhci-r8a7743" for r8a7743 SoC
     - "renesas,xhci-r8a7790" for r8a7790 SoC
     - "renesas,xhci-r8a7791" for r8a7791 SoC
     - "renesas,xhci-r8a7793" for r8a7793 SoC
     - "renesas,xhci-r8a7795" for r8a7795 SoC
     - "renesas,xhci-r8a7796" for r8a7796 SoC
-    - "renesas,rcar-gen2-xhci" for a generic R-Car Gen2 compatible device
+    - "renesas,rcar-gen2-xhci" for a generic R-Car Gen2 or RZ/G1 compatible
+      device
     - "renesas,rcar-gen3-xhci" for a generic R-Car Gen3 compatible device
     - "xhci-platform" (deprecated)
 
@@ -29,6 +31,7 @@ Optional properties:
   - usb2-lpm-disable: indicate if we don't want to enable USB2 HW LPM
   - usb3-lpm-capable: determines if platform is USB3 LPM capable
   - quirk-broken-port-ped: set if the controller has broken port disable mechanism
+  - imod-interval-ns: default interrupt moderation interval is 5000ns
 
 Example:
 	usb@f0931000 {