dts: update to v4.3-rc3

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

10 files changed, 49 insertions, 25 deletions

diff --git a/dts/Bindings/arm/gic-v3.txt b/dts/Bindings/arm/gic-v3.txt
index ddfade40ac..7803e77d85 100644
--- a/dts/Bindings/arm/gic-v3.txt
+++ b/dts/Bindings/arm/gic-v3.txt
@@ -57,6 +57,8 @@ used to route Message Signalled Interrupts (MSI) to the CPUs.
 These nodes must have the following properties:
 - compatible : Should at least contain  "arm,gic-v3-its".
 - msi-controller : Boolean property. Identifies the node as an MSI controller
+- #msi-cells: Must be <1>. The single msi-cell is the DeviceID of the device
+  which will generate the MSI.
 - reg: Specifies the base physical address and size of the ITS
   registers.
 
@@ -83,6 +85,7 @@ Examples:
 		gic-its@2c200000 {
 			compatible = "arm,gic-v3-its";
 			msi-controller;
+			#msi-cells = <1>;
 			reg = <0x0 0x2c200000 0 0x200000>;
 		};
 	};
@@ -107,12 +110,14 @@ Examples:
 		gic-its@2c200000 {
 			compatible = "arm,gic-v3-its";
 			msi-controller;
+			#msi-cells = <1>;
 			reg = <0x0 0x2c200000 0 0x200000>;
 		};
 
 		gic-its@2c400000 {
 			compatible = "arm,gic-v3-its";
 			msi-controller;
+			#msi-cells = <1>;
 			reg = <0x0 0x2c400000 0 0x200000>;
 		};
 	};
diff --git a/dts/Bindings/arm/idle-states.txt b/dts/Bindings/arm/idle-states.txt
index a8274eabae..b8e41c148a 100644
--- a/dts/Bindings/arm/idle-states.txt
+++ b/dts/Bindings/arm/idle-states.txt
@@ -497,7 +497,7 @@ cpus {
 	};
 
 	idle-states {
-		entry-method = "arm,psci";
+		entry-method = "psci";
 
 		CPU_RETENTION_0_0: cpu-retention-0-0 {
 			compatible = "arm,idle-state";
diff --git a/dts/Bindings/gpio/gpio.txt b/dts/Bindings/gpio/gpio.txt
index 5788d5cf12..82d40e2505 100644
--- a/dts/Bindings/gpio/gpio.txt
+++ b/dts/Bindings/gpio/gpio.txt
@@ -16,7 +16,9 @@ properties, each containing a 'gpio-list':
 GPIO properties should be named "[<name>-]gpios", with <name> being the purpose
 of this GPIO for the device. While a non-existent <name> is considered valid
 for compatibility reasons (resolving to the "gpios" property), it is not allowed
-for new bindings.
+for new bindings. Also, GPIO properties named "[<name>-]gpio" are valid and old
+bindings use it, but are only supported for compatibility reasons and should not
+be used for newer bindings since it has been deprecated.
 
 GPIO properties can contain one or more GPIO phandles, but only in exceptional
 cases should they contain more than one. If your device uses several GPIOs with
diff --git a/dts/Bindings/iio/accel/bma180.txt b/dts/Bindings/iio/accel/bma180.txt
index c5933573e0..4a3679d544 100644
--- a/dts/Bindings/iio/accel/bma180.txt
+++ b/dts/Bindings/iio/accel/bma180.txt
@@ -1,10 +1,11 @@
-* Bosch BMA180 triaxial acceleration sensor
+* Bosch BMA180 / BMA250 triaxial acceleration sensor
 
 http://omapworld.com/BMA180_111_1002839.pdf
+http://ae-bst.resource.bosch.com/media/products/dokumente/bma250/bst-bma250-ds002-05.pdf
 
 Required properties:
 
-  - compatible : should be "bosch,bma180"
+  - compatible : should be "bosch,bma180" or "bosch,bma250"
   - reg : the I2C address of the sensor
 
 Optional properties:
@@ -13,6 +14,9 @@ Optional properties:
 
   - interrupts : interrupt mapping for GPIO IRQ, it should by configured with
 		flags IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_EDGE_RISING
+		For the bma250 the first interrupt listed must be the one
+		connected to the INT1 pin, the second (optional) interrupt
+		listed must be the one connected to the INT2 pin.
 
 Example:
 
diff --git a/dts/Bindings/pci/pci-rcar-gen2.txt b/dts/Bindings/pci/pci-rcar-gen2.txt
index d8ef5bf50f..7fab84b335 100644
--- a/dts/Bindings/pci/pci-rcar-gen2.txt
+++ b/dts/Bindings/pci/pci-rcar-gen2.txt
@@ -7,7 +7,8 @@ OHCI and EHCI controllers.
 
 Required properties:
 - compatible: "renesas,pci-r8a7790" for the R8A7790 SoC;
-	      "renesas,pci-r8a7791" for the R8A7791 SoC.
+	      "renesas,pci-r8a7791" for the R8A7791 SoC;
+	      "renesas,pci-r8a7794" for the R8A7794 SoC.
 - reg:	A list of physical regions to access the device: the first is
 	the operational registers for the OHCI/EHCI controllers and the
 	second is for the bridge configuration and control registers.
diff --git a/dts/Bindings/regulator/pbias-regulator.txt b/dts/Bindings/regulator/pbias-regulator.txt
index 32aa26f1e4..acbcb452a6 100644
--- a/dts/Bindings/regulator/pbias-regulator.txt
+++ b/dts/Bindings/regulator/pbias-regulator.txt
@@ -2,7 +2,12 @@ PBIAS internal regulator for SD card dual voltage i/o pads on OMAP SoCs.
 
 Required properties:
 - compatible:
-  - "ti,pbias-omap" for OMAP2, OMAP3, OMAP4, OMAP5, DRA7.
+  - should be "ti,pbias-dra7" for DRA7
+  - should be "ti,pbias-omap2" for OMAP2
+  - should be "ti,pbias-omap3" for OMAP3
+  - should be "ti,pbias-omap4" for OMAP4
+  - should be "ti,pbias-omap5" for OMAP5
+  - "ti,pbias-omap" is deprecated
 - reg: pbias register offset from syscon base and size of pbias register.
 - syscon : phandle of the system control module
 - regulator-name : should be
diff --git a/dts/Bindings/spi/spi-mt65xx.txt b/dts/Bindings/spi/spi-mt65xx.txt
index dcefc43827..6160ffbcb3 100644
--- a/dts/Bindings/spi/spi-mt65xx.txt
+++ b/dts/Bindings/spi/spi-mt65xx.txt
@@ -15,17 +15,18 @@ Required properties:
 - interrupts: Should contain spi interrupt
 
 - clocks: phandles to input clocks.
-  The first should be <&topckgen CLK_TOP_SPI_SEL>.
-  The second should be one of the following.
+  The first should be one of the following. It's PLL.
    -  <&clk26m>: specify parent clock 26MHZ.
    -  <&topckgen CLK_TOP_SYSPLL3_D2>: specify parent clock 109MHZ.
 				      It's the default one.
    -  <&topckgen CLK_TOP_SYSPLL4_D2>: specify parent clock 78MHZ.
    -  <&topckgen CLK_TOP_UNIVPLL2_D4>: specify parent clock 104MHZ.
    -  <&topckgen CLK_TOP_UNIVPLL1_D8>: specify parent clock 78MHZ.
+  The second should be <&topckgen CLK_TOP_SPI_SEL>. It's clock mux.
+  The third is <&pericfg CLK_PERI_SPI0>. It's clock gate.
 
-- clock-names: shall be "spi-clk" for the controller clock, and
-  "parent-clk" for the parent clock.
+- clock-names: shall be "parent-clk" for the parent clock, "sel-clk" for the
+  muxes clock, and "spi-clk" for the clock gate.
 
 Optional properties:
 - mediatek,pad-select: specify which pins group(ck/mi/mo/cs) spi
@@ -44,8 +45,11 @@ spi: spi@1100a000 {
 	#size-cells = <0>;
 	reg = <0 0x1100a000 0 0x1000>;
 	interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_LOW>;
-	clocks = <&topckgen CLK_TOP_SPI_SEL>, <&topckgen CLK_TOP_SYSPLL3_D2>;
-	clock-names = "spi-clk", "parent-clk";
+	clocks = <&topckgen CLK_TOP_SYSPLL3_D2>,
+		 <&topckgen CLK_TOP_SPI_SEL>,
+		 <&pericfg CLK_PERI_SPI0>;
+	clock-names = "parent-clk", "sel-clk", "spi-clk";
+
 	mediatek,pad-select = <0>;
 	status = "disabled";
 };
diff --git a/dts/Bindings/thermal/thermal.txt b/dts/Bindings/thermal/thermal.txt
index 8a49362dea..41b817f7b6 100644
--- a/dts/Bindings/thermal/thermal.txt
+++ b/dts/Bindings/thermal/thermal.txt
@@ -55,19 +55,11 @@ of heat dissipation). For example a fan's cooling states correspond to
 the different fan speeds possible. Cooling states are referred to by
 single unsigned integers, where larger numbers mean greater heat
 dissipation. The precise set of cooling states associated with a device
-(as referred to be the cooling-min-state and cooling-max-state
+(as referred to by the cooling-min-level and cooling-max-level
 properties) should be defined in a particular device's binding.
 For more examples of cooling devices, refer to the example sections below.
 
 Required properties:
-- cooling-min-state:	An integer indicating the smallest
-  Type: unsigned	cooling state accepted. Typically 0.
-  Size: one cell
-
-- cooling-max-state:	An integer indicating the largest
-  Type: unsigned	cooling state accepted.
-  Size: one cell
-
 - #cooling-cells:	Used to provide cooling device specific information
   Type: unsigned	while referring to it. Must be at least 2, in order
   Size: one cell      	to specify minimum and maximum cooling state used
@@ -77,6 +69,15 @@ Required properties:
 			See Cooling device maps section below for more details
 			on how consumers refer to cooling devices.
 
+Optional properties:
+- cooling-min-level:	An integer indicating the smallest
+  Type: unsigned	cooling state accepted. Typically 0.
+  Size: one cell
+
+- cooling-max-level:	An integer indicating the largest
+  Type: unsigned	cooling state accepted.
+  Size: one cell
+
 * Trip points
 
 The trip node is a node to describe a point in the temperature domain
@@ -225,8 +226,8 @@ cpus {
 			396000  950000
 			198000  850000
 		>;
-		cooling-min-state = <0>;
-		cooling-max-state = <3>;
+		cooling-min-level = <0>;
+		cooling-max-level = <3>;
 		#cooling-cells = <2>; /* min followed by max */
 	};
 	...
@@ -240,8 +241,8 @@ cpus {
 	 */
 	fan0: fan@0x48 {
 		...
-		cooling-min-state = <0>;
-		cooling-max-state = <9>;
+		cooling-min-level = <0>;
+		cooling-max-level = <9>;
 		#cooling-cells = <2>; /* min followed by max */
 	};
 };
diff --git a/dts/Bindings/usb/ci-hdrc-usb2.txt b/dts/Bindings/usb/ci-hdrc-usb2.txt
index d71ef07bca..a057b75ba4 100644
--- a/dts/Bindings/usb/ci-hdrc-usb2.txt
+++ b/dts/Bindings/usb/ci-hdrc-usb2.txt
@@ -6,6 +6,7 @@ Required properties:
 	"lsi,zevio-usb"
 	"qcom,ci-hdrc"
 	"chipidea,usb2"
+	"xlnx,zynq-usb-2.20a"
 - reg: base address and length of the registers
 - interrupts: interrupt for the USB controller
 
diff --git a/dts/Bindings/vendor-prefixes.txt b/dts/Bindings/vendor-prefixes.txt
index ac5f0c34ae..82d2ac97af 100644
--- a/dts/Bindings/vendor-prefixes.txt
+++ b/dts/Bindings/vendor-prefixes.txt
@@ -203,6 +203,7 @@ sitronix	Sitronix Technology Corporation
 skyworks	Skyworks Solutions, Inc.
 smsc	Standard Microsystems Corporation
 snps	Synopsys, Inc.
+socionext	Socionext Inc.
 solidrun	SolidRun
 solomon        Solomon Systech Limited
 sony	Sony Corporation