dts: update to v5.18-rc2

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

6 files changed, 15 insertions, 20 deletions

diff --git a/dts/Bindings/display/bridge/chipone,icn6211.yaml b/dts/Bindings/display/bridge/chipone,icn6211.yaml
index 62c3bd4cb2..7257fd0ae4 100644
--- a/dts/Bindings/display/bridge/chipone,icn6211.yaml
+++ b/dts/Bindings/display/bridge/chipone,icn6211.yaml
@@ -51,7 +51,6 @@ properties:
           Video port for MIPI DPI output (panel or connector).
 
     required:
-      - port@0
       - port@1
 
 required:
diff --git a/dts/Bindings/display/bridge/toshiba,tc358762.yaml b/dts/Bindings/display/bridge/toshiba,tc358762.yaml
index 5216c27fc0..a412a1da95 100644
--- a/dts/Bindings/display/bridge/toshiba,tc358762.yaml
+++ b/dts/Bindings/display/bridge/toshiba,tc358762.yaml
@@ -39,7 +39,6 @@ properties:
           Video port for MIPI DPI output (panel or connector).
 
     required:
-      - port@0
       - port@1
 
 required:
diff --git a/dts/Bindings/display/panel/panel-mipi-dbi-spi.yaml b/dts/Bindings/display/panel/panel-mipi-dbi-spi.yaml
index f29789994b..c2df8d28aa 100644
--- a/dts/Bindings/display/panel/panel-mipi-dbi-spi.yaml
+++ b/dts/Bindings/display/panel/panel-mipi-dbi-spi.yaml
@@ -83,6 +83,8 @@ properties:
 required:
   - compatible
   - reg
+  - width-mm
+  - height-mm
   - panel-timing
 
 unevaluatedProperties: false
diff --git a/dts/Bindings/net/ethernet-controller.yaml b/dts/Bindings/net/ethernet-controller.yaml
index 817794e562..4f15463611 100644
--- a/dts/Bindings/net/ethernet-controller.yaml
+++ b/dts/Bindings/net/ethernet-controller.yaml
@@ -106,6 +106,12 @@ properties:
   phy-mode:
     $ref: "#/properties/phy-connection-type"
 
+  pcs-handle:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description:
+      Specifies a reference to a node representing a PCS PHY device on a MDIO
+      bus to link with an external PHY (phy-handle) if exists.
+
   phy-handle:
     $ref: /schemas/types.yaml#/definitions/phandle
     description:
diff --git a/dts/Bindings/net/micrel.txt b/dts/Bindings/net/micrel.txt
index c5ab62c391..8d157f0295 100644
--- a/dts/Bindings/net/micrel.txt
+++ b/dts/Bindings/net/micrel.txt
@@ -45,20 +45,3 @@ Optional properties:
 
 	In fiber mode, auto-negotiation is disabled and the PHY can only work in
 	100base-fx (full and half duplex) modes.
-
- - lan8814,ignore-ts: If present the PHY will not support timestamping.
-
-	This option acts as check whether Timestamping is supported by
-	hardware or not. LAN8814 phy support hardware tmestamping.
-
- - lan8814,latency_rx_10: Configures Latency value of phy in ingress at 10 Mbps.
-
- - lan8814,latency_tx_10: Configures Latency value of phy in egress at 10 Mbps.
-
- - lan8814,latency_rx_100: Configures Latency value of phy in ingress at 100 Mbps.
-
- - lan8814,latency_tx_100: Configures Latency value of phy in egress at 100 Mbps.
-
- - lan8814,latency_rx_1000: Configures Latency value of phy in ingress at 1000 Mbps.
-
- - lan8814,latency_tx_1000: Configures Latency value of phy in egress at 1000 Mbps.
diff --git a/dts/Bindings/net/xilinx_axienet.txt b/dts/Bindings/net/xilinx_axienet.txt
index b8e4894bc6..1aa4c6006c 100644
--- a/dts/Bindings/net/xilinx_axienet.txt
+++ b/dts/Bindings/net/xilinx_axienet.txt
@@ -26,7 +26,8 @@ Required properties:
 		  specified, the TX/RX DMA interrupts should be on that node
 		  instead, and only the Ethernet core interrupt is optionally
 		  specified here.
-- phy-handle	: Should point to the external phy device.
+- phy-handle	: Should point to the external phy device if exists. Pointing
+		  this to the PCS/PMA PHY is deprecated and should be avoided.
 		  See ethernet.txt file in the same directory.
 - xlnx,rxmem	: Set to allocated memory buffer for Rx/Tx in the hardware
 
@@ -68,6 +69,11 @@ Optional properties:
 		  required through the core's MDIO interface (i.e. always,
 		  unless the PHY is accessed through a different bus).
 
+ - pcs-handle: 	  Phandle to the internal PCS/PMA PHY in SGMII or 1000Base-X
+		  modes, where "pcs-handle" should be used to point
+		  to the PCS/PMA PHY, and "phy-handle" should point to an
+		  external PHY if exists.
+
 Example:
 	axi_ethernet_eth: ethernet@40c00000 {
 		compatible = "xlnx,axi-ethernet-1.00.a";