net: rework the mii support

this rework is done in order to add a phylib and allow to have phy driver support

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

1 files changed, 232 insertions, 0 deletions

diff --git a/include/linux/mii.h b/include/linux/mii.h
new file mode 100644
index 0000000000..734517268f
--- /dev/null
+++ b/include/linux/mii.h
@@ -0,0 +1,232 @@
+/*
+ * linux/mii.h: definitions for MII-compatible transceivers
+ * Originally drivers/net/sunhme.h.
+ *
+ * Copyright (C) 1996, 1999, 2001 David S. Miller (davem@redhat.com)
+ */
+
+#ifndef __LINUX_MII_H__
+#define __LINUX_MII_H__
+
+/* Generic MII registers. */
+
+#define MII_BMCR            0x00        /* Basic mode control register */
+#define MII_BMSR            0x01        /* Basic mode status register  */
+#define MII_PHYSID1         0x02        /* PHYS ID 1                   */
+#define MII_PHYSID2         0x03        /* PHYS ID 2                   */
+#define MII_ADVERTISE       0x04        /* Advertisement control reg   */
+#define MII_LPA             0x05        /* Link partner ability reg    */
+#define MII_EXPANSION       0x06        /* Expansion register          */
+#define MII_CTRL1000        0x09        /* 1000BASE-T control          */
+#define MII_STAT1000        0x0a        /* 1000BASE-T status           */
+#define MII_ESTATUS	    0x0f	/* Extended Status */
+#define MII_DCOUNTER        0x12        /* Disconnect counter          */
+#define MII_FCSCOUNTER      0x13        /* False carrier counter       */
+#define MII_NWAYTEST        0x14        /* N-way auto-neg test reg     */
+#define MII_RERRCOUNTER     0x15        /* Receive error counter       */
+#define MII_SREVISION       0x16        /* Silicon revision            */
+#define MII_RESV1           0x17        /* Reserved...                 */
+#define MII_LBRERROR        0x18        /* Lpback, rx, bypass error    */
+#define MII_PHYADDR         0x19        /* PHY address                 */
+#define MII_RESV2           0x1a        /* Reserved...                 */
+#define MII_TPISTATUS       0x1b        /* TPI status for 10mbps       */
+#define MII_NCONFIG         0x1c        /* Network interface config    */
+
+/* Basic mode control register. */
+#define BMCR_SPEED_MASK		0x2040	/* 10/100/1000		       */
+#define BMCR_SPEED10		0x0000	/* Select 10Mbps	       */
+#define BMCR_RESV               0x003f  /* Unused...                   */
+#define BMCR_SPEED1000		0x0040  /* MSB of Speed (1000)         */
+#define BMCR_CTST               0x0080  /* Collision test              */
+#define BMCR_FULLDPLX           0x0100  /* Full duplex                 */
+#define BMCR_ANRESTART          0x0200  /* Auto negotiation restart    */
+#define BMCR_ISOLATE            0x0400  /* Disconnect DP83840 from MII */
+#define BMCR_PDOWN              0x0800  /* Powerdown the DP83840       */
+#define BMCR_ANENABLE           0x1000  /* Enable auto negotiation     */
+#define BMCR_SPEED100           0x2000  /* Select 100Mbps              */
+#define BMCR_LOOPBACK           0x4000  /* TXD loopback bits           */
+#define BMCR_RESET              0x8000  /* Reset the DP83840           */
+
+/* Basic mode status register. */
+#define BMSR_ERCAP              0x0001  /* Ext-reg capability          */
+#define BMSR_JCD                0x0002  /* Jabber detected             */
+#define BMSR_LSTATUS            0x0004  /* Link status                 */
+#define BMSR_ANEGCAPABLE        0x0008  /* Able to do auto-negotiation */
+#define BMSR_RFAULT             0x0010  /* Remote fault detected       */
+#define BMSR_ANEGCOMPLETE       0x0020  /* Auto-negotiation complete   */
+#define BMSR_RESV               0x00c0  /* Unused...                   */
+#define BMSR_ESTATEN		0x0100	/* Extended Status in R15 */
+#define BMSR_100HALF2           0x0200  /* Can do 100BASE-T2 HDX */
+#define BMSR_100FULL2           0x0400  /* Can do 100BASE-T2 FDX */
+#define BMSR_10HALF             0x0800  /* Can do 10mbps, half-duplex  */
+#define BMSR_10FULL             0x1000  /* Can do 10mbps, full-duplex  */
+#define BMSR_100HALF            0x2000  /* Can do 100mbps, half-duplex */
+#define BMSR_100FULL            0x4000  /* Can do 100mbps, full-duplex */
+#define BMSR_100BASE4           0x8000  /* Can do 100mbps, 4k packets  */
+
+/* Advertisement control register. */
+#define ADVERTISE_SLCT          0x001f  /* Selector bits               */
+#define ADVERTISE_CSMA          0x0001  /* Only selector supported     */
+#define ADVERTISE_10HALF        0x0020  /* Try for 10mbps half-duplex  */
+#define ADVERTISE_1000XFULL     0x0020  /* Try for 1000BASE-X full-duplex */
+#define ADVERTISE_10FULL        0x0040  /* Try for 10mbps full-duplex  */
+#define ADVERTISE_1000XHALF     0x0040  /* Try for 1000BASE-X half-duplex */
+#define ADVERTISE_100HALF       0x0080  /* Try for 100mbps half-duplex */
+#define ADVERTISE_1000XPAUSE    0x0080  /* Try for 1000BASE-X pause    */
+#define ADVERTISE_100FULL       0x0100  /* Try for 100mbps full-duplex */
+#define ADVERTISE_1000XPSE_ASYM 0x0100  /* Try for 1000BASE-X asym pause */
+#define ADVERTISE_100BASE4      0x0200  /* Try for 100mbps 4k packets  */
+#define ADVERTISE_PAUSE_CAP     0x0400  /* Try for pause               */
+#define ADVERTISE_PAUSE_ASYM    0x0800  /* Try for asymetric pause     */
+#define ADVERTISE_RESV          0x1000  /* Unused...                   */
+#define ADVERTISE_RFAULT        0x2000  /* Say we can detect faults    */
+#define ADVERTISE_LPACK         0x4000  /* Ack link partners response  */
+#define ADVERTISE_NPAGE         0x8000  /* Next page bit               */
+
+#define ADVERTISE_FULL (ADVERTISE_100FULL | ADVERTISE_10FULL | \
+			ADVERTISE_CSMA)
+#define ADVERTISE_ALL (ADVERTISE_10HALF | ADVERTISE_10FULL | \
+                       ADVERTISE_100HALF | ADVERTISE_100FULL)
+
+/* Link partner ability register. */
+#define LPA_SLCT                0x001f  /* Same as advertise selector  */
+#define LPA_10HALF              0x0020  /* Can do 10mbps half-duplex   */
+#define LPA_1000XFULL           0x0020  /* Can do 1000BASE-X full-duplex */
+#define LPA_10FULL              0x0040  /* Can do 10mbps full-duplex   */
+#define LPA_1000XHALF           0x0040  /* Can do 1000BASE-X half-duplex */
+#define LPA_100HALF             0x0080  /* Can do 100mbps half-duplex  */
+#define LPA_1000XPAUSE          0x0080  /* Can do 1000BASE-X pause     */
+#define LPA_100FULL             0x0100  /* Can do 100mbps full-duplex  */
+#define LPA_1000XPAUSE_ASYM     0x0100  /* Can do 1000BASE-X pause asym*/
+#define LPA_100BASE4            0x0200  /* Can do 100mbps 4k packets   */
+#define LPA_PAUSE_CAP           0x0400  /* Can pause                   */
+#define LPA_PAUSE_ASYM          0x0800  /* Can pause asymetrically     */
+#define LPA_RESV                0x1000  /* Unused...                   */
+#define LPA_RFAULT              0x2000  /* Link partner faulted        */
+#define LPA_LPACK               0x4000  /* Link partner acked us       */
+#define LPA_NPAGE               0x8000  /* Next page bit               */
+
+#define LPA_DUPLEX		(LPA_10FULL | LPA_100FULL)
+#define LPA_100			(LPA_100FULL | LPA_100HALF | LPA_100BASE4)
+
+/* Expansion register for auto-negotiation. */
+#define EXPANSION_NWAY          0x0001  /* Can do N-way auto-nego      */
+#define EXPANSION_LCWP          0x0002  /* Got new RX page code word   */
+#define EXPANSION_ENABLENPAGE   0x0004  /* This enables npage words    */
+#define EXPANSION_NPCAPABLE     0x0008  /* Link partner supports npage */
+#define EXPANSION_MFAULTS       0x0010  /* Multiple faults detected    */
+#define EXPANSION_RESV          0xffe0  /* Unused...                   */
+
+#define ESTATUS_1000_TFULL	0x2000	/* Can do 1000BT Full */
+#define ESTATUS_1000_THALF	0x1000	/* Can do 1000BT Half */
+
+/* N-way test register. */
+#define NWAYTEST_RESV1          0x00ff  /* Unused...                   */
+#define NWAYTEST_LOOPBACK       0x0100  /* Enable loopback for N-way   */
+#define NWAYTEST_RESV2          0xfe00  /* Unused...                   */
+
+/* 1000BASE-T Control register */
+#define ADVERTISE_1000FULL      0x0200  /* Advertise 1000BASE-T full duplex */
+#define ADVERTISE_1000HALF      0x0100  /* Advertise 1000BASE-T half duplex */
+
+/* 1000BASE-T Status register */
+#define LPA_1000LOCALRXOK       0x2000  /* Link partner local receiver status */
+#define LPA_1000REMRXOK         0x1000  /* Link partner remote receiver status */
+#define LPA_1000FULL            0x0800  /* Link partner 1000BASE-T full duplex */
+#define LPA_1000HALF            0x0400  /* Link partner 1000BASE-T half duplex */
+
+/* Flow control flags */
+#define FLOW_CTRL_TX		0x01
+#define FLOW_CTRL_RX		0x02
+
+/**
+ * mii_nway_result
+ * @negotiated: value of MII ANAR and'd with ANLPAR
+ *
+ * Given a set of MII abilities, check each bit and returns the
+ * currently supported media, in the priority order defined by
+ * IEEE 802.3u.  We use LPA_xxx constants but note this is not the
+ * value of LPA solely, as described above.
+ *
+ * The one exception to IEEE 802.3u is that 100baseT4 is placed
+ * between 100T-full and 100T-half.  If your phy does not support
+ * 100T4 this is fine.  If your phy places 100T4 elsewhere in the
+ * priority order, you will need to roll your own function.
+ */
+static inline unsigned int mii_nway_result (unsigned int negotiated)
+{
+	unsigned int ret;
+
+	if (negotiated & LPA_100FULL)
+		ret = LPA_100FULL;
+	else if (negotiated & LPA_100BASE4)
+		ret = LPA_100BASE4;
+	else if (negotiated & LPA_100HALF)
+		ret = LPA_100HALF;
+	else if (negotiated & LPA_10FULL)
+		ret = LPA_10FULL;
+	else
+		ret = LPA_10HALF;
+
+	return ret;
+}
+
+/**
+ * mii_duplex
+ * @duplex_lock: Non-zero if duplex is locked at full
+ * @negotiated: value of MII ANAR and'd with ANLPAR
+ *
+ * A small helper function for a common case.  Returns one
+ * if the media is operating or locked at full duplex, and
+ * returns zero otherwise.
+ */
+static inline unsigned int mii_duplex (unsigned int duplex_lock,
+				       unsigned int negotiated)
+{
+	if (duplex_lock)
+		return 1;
+	if (mii_nway_result(negotiated) & LPA_DUPLEX)
+		return 1;
+	return 0;
+}
+
+/**
+ * mii_advertise_flowctrl - get flow control advertisement flags
+ * @cap: Flow control capabilities (FLOW_CTRL_RX, FLOW_CTRL_TX or both)
+ */
+static inline u16 mii_advertise_flowctrl(int cap)
+{
+	u16 adv = 0;
+
+	if (cap & FLOW_CTRL_RX)
+		adv = ADVERTISE_PAUSE_CAP | ADVERTISE_PAUSE_ASYM;
+	if (cap & FLOW_CTRL_TX)
+		adv ^= ADVERTISE_PAUSE_ASYM;
+
+	return adv;
+}
+
+/**
+ * mii_resolve_flowctrl_fdx
+ * @lcladv: value of MII ADVERTISE register
+ * @rmtadv: value of MII LPA register
+ *
+ * Resolve full duplex flow control as per IEEE 802.3-2005 table 28B-3
+ */
+static inline u8 mii_resolve_flowctrl_fdx(u16 lcladv, u16 rmtadv)
+{
+	u8 cap = 0;
+
+	if (lcladv & rmtadv & ADVERTISE_PAUSE_CAP) {
+		cap = FLOW_CTRL_TX | FLOW_CTRL_RX;
+	} else if (lcladv & rmtadv & ADVERTISE_PAUSE_ASYM) {
+		if (lcladv & ADVERTISE_PAUSE_CAP)
+			cap = FLOW_CTRL_RX;
+		else if (rmtadv & ADVERTISE_PAUSE_CAP)
+			cap = FLOW_CTRL_TX;
+	}
+
+	return cap;
+}
+
+#endif /* __LINUX_MII_H__ */